Technogym Skillmill GO Technical Service Manual
  1. Manuals
  2. Brands
  3. Technogym Manuals
  4. Treadmill
  5. Skillmill GO
  6. Technical service manual

Technogym Skillmill GO Technical Service Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

S
killmill
T
S
G
echnical
ervice
uide
r
. 2.2 - (SePTemBer 2016)
ev

Advertisement

Table of Contents
loading

Related Manuals for Technogym Skillmill GO

Summary of Contents for Technogym Skillmill GO

  • Page 1 killmill echnical ervice uide . 2.2 - (SePTemBer 2016)
  • Page 3 The information in this manual is intended for QUALIFIED TECHNICAL PERSONNEL, who have been specifically trained by Technogym S.p.A. and are qualified to carry out fine-tuning and start- up of the equipment, as well as major maintenance work and repairs, requiring in-depth under- standing of the equipment, how it works, its safety devices and maintenance procedures.
  • Page 4 Skillmill Technical Service Guide - Rev. 2.2 Blank page. Page 4 e-mail: support@technogym.com...

  • Page 5: Table Of Contents

    Battery (Console version) ....................28 3 . 1 . 8 NFC (connect version) ....................... 31 3 . 1 . 9 Bluetooth smart ........................ 31 3 . 1 . 10 WiFi (connect version) ...................... 31 ACCESSORIES ......................... 33 MOVING AND INSTALLING THE EQUIPMENT ..........35 e-mail: support@technogym.com Page 5...
  • Page 6 6 . 3 . 1 Steps necessary for configuring the SKILLMILL application ........47 6 . 4 Display configuration (Connect version) ..........48 6 . 5 TROUBLESHOOTING ................. 50 6 . 5 . 1 The display does not turn on (Connect version) ............50 6 . 5 . 2 The display does not turn on (Console version) ............51 e-mail: support@technogym.com Page 6...
  • Page 7 10. PLANNED MAINTENANCE ..................... 69 11. TOOLS TO BE USED ......................71 12. LIST OF CHANGES FOR MANUAL REVISION ............. 73 12 . 1 REVISION 1 . 1 ....................73 12 . 2 revision 2 . 0 ....................... 73 e-mail: support@technogym.com Page 7...
  • Page 8 Skillmill Technical Service Guide - Rev. 2.2 12 . 3 revision 2 . 1 ....................... 73 12 . 4 revision 2 . 2 ....................... 74 e-mail: support@technogym.com Page 8...

  • Page 9: General Warnings

    Technical Service Guide - Rev. 2.2 GENERAL WARNINGS INTRODUCTION This document has been prepared specifically for Technogym After Sales Service, with the aim of providing authorised personnel with the information for carrying out maintenance and repair operations in the correct manner.

  • Page 10: Useful Advice

    Technical Service Guide - Rev. 2.2 USEFUL ADVICE Technogym advises you to plan your technical assistance task in the following way: Carefully assess the impressions reported by the Customer regarding the equipment’s operating faults and ask questions suitable to clarify the signs of the defect.

  • Page 11: Technical Specifications

    Rechargeable Battery LPS 5V Wall Supply Yes, via NFC (RFID), mywellness® platform QR Code, Bluetooth connectivity connection Wi-Fi® IEEE 802.11b/g 2.4 Ghz Network connectivity Security: WPA / WPA2 / WEP / none (open network) Used for Bluetooth Used for Bluetooth Bluetooth smart connectivity Chest Belt Chest Belt and Login Resistance technology Multidrive Technology - patent pending Magnetic resistance in 11 Levels (0 Resistance Off - 1-3 Low - 4-6 Resistance control Mid - 7-9 High - 10 Max) Platform type Foil, formed by means of EPDM injection Platform trajectory control On-slat bearings Platform dimensions (LxW) 1680 x 480 mm (66” x 19”) Cell phone holder Holds phones up to 77.8 mm Table 1 e-mail: support@technogym.com Page 11...

  • Page 12: Mechanical Characteristics

    1910 mm - 75.2” WIDTH (W) 890 mm - 35” HEIGHT (H) 1540 mm - 60.6” WEIGHT (of the equipment) 180 kg - 397 lbs MAXIMUM USER WEIGHT 180 kg - 397 lbs Table 2 1910 mm 890 mm (75,2") (35") Figure 1 Page 12 e-mail: support@technogym.com...

  • Page 13: Dimensions And Weight Of Packaging

    2.1.2 DIMENSIONS AND WEIGHT OF PACKAGING The equipment may be shipped in two ways depending on the country of destination: • Italy: equipment without cardboard, assembled and bagged; • Abroad: equipment disassembled with cardboard packaging (for the assembly, refer to the distribu- tion logistics course or the document “Skillmill - Assembly instructions” contained in the packag- ing). Italy packaging 2250 x 1030 x 1760 (mm) DIMENSIONS (L x W x H) 88.6 x 40.6 x 69.3 (inch) WEIGHT 200 kg - 441 lbs Table 3 Figure 2 e-mail: support@technogym.com Page 13...

  • Page 14: Environmental Characteristics

    Technical Service Guide - Rev. 2.2 External packaging 2250 x 1030 x 800 (mm) DIMENSIONS (L x W x H) 88.6 x 40.6 x 31.5 (inch) WEIGHT 240 kg MAX - 529 lbs MAX Table 4 Figure 3 ENVIRONMENTAL CHARACTERISTICS In operation from +10° to 25°C Temperature In storage from -10° to 70°C In operation from 20% to 90% Dampness In storage from 20% to 90% Table 5 Page 14 e-mail: support@technogym.com...

  • Page 15: Conformity With Standards And Directives

    EN61000-3-2 • EN61000-3-3 • ISO EN 20957-1 EUROPEAN REFERENCE STANDARDS • EN 957-6 • EN 62233 • ETSI EN 300 329 • ETSI EN 301 489-1 • ETSI EN 301 489-17 • Regulation 1275/2008 • Standard UL1647 AMERICAN REFERENCE STANDARDS • FCC 15 Table 6 The reference Directives and Standards are subject to legal changes, those indicated in these manuals are valid at the moment of product release. The Directives and Standards updated for a specific product are included in the Declaration of Con- formity and delivered with every product. e-mail: support@technogym.com Page 15...

  • Page 16: Equipment Coding

    T = TGS 8, 9 Frame colour AN = Anthracite 10, 11 Upholstery colour 00 = None 12, 13, Guard colour EA = Anthracite 14, 15, Plastics colour NR = Black 0 = None Packaging and power 1 = Standard packaging supply 2 = External packaging Table 7 For example, a possible code number could be the following: Page 16 e-mail: support@technogym.com...

  • Page 17: Serial Number Structure

    DJ = Line K = Skillmill 0 = Standard 1 = UL 1, 2, 3, 4, 5, 6 Type of product 3 = Powered 4 = Battery N = None D = Display N = None 7, 8 Year of production 9, 10, 11, 12, 13, 14 Progressive 000001 Table 8 For example, a possible SN code is as follows: 000001 e-mail: support@technogym.com Page 17...

  • Page 18: Position Of Serial Number And Equipment Code

    POSITION OF SERIAL NUMBER AND EQUIPMENT CODE There are two labels indicating the serial number and equipment code: below the central handlebar; below the left side guard on the frame. Technogym S.p.A. Via Calcinaro 2861, Cesena (FC) Made in Italy SKILLMILL Model No: DJK03D...

  • Page 19: Wiring Diagrams

    BOARD Patch Patch TX and RX Patch connection connection connection CU0867 CU0864 CU0884 LOW KIT Patch connection CU0865 CPU BOARD POWER SUPPLY CU0855 CU0866 +5.5V TX and RX CU0853 CU0883 Patch Patch connection connection Figure 5 e-mail: support@technogym.com Page 19...

  • Page 20: Wiring Diagram, Console Version

    CU0867 CU0864 LOW KIT CPU BOARD CU0890 CU0866 +5.5V TX and RX CU0853 CU0883 Battery CU0889 Patch Patch connection connection POWER SUPPLY Figure 6 2.7.3 WIRING DIAGRAM, GO VERSION It is not equipped with electronic components. Page 20 e-mail: support@technogym.com...

  • Page 21: Cables

    (NFC / Patch connector) NFC Board Signal Colour Patch connector +3.3 Vdc NFC Yellow rs232_RFID_RX Brown rs232_RFID_TX White DGND Green CU0855: 5V power supply cable (Power supply/ Low Kit) Low Kit board Signal Colour 5V input JACK 5.5 Vdc 5.5 Vdc Black Black e-mail: support@technogym.com Page 21...
  • Page 22 Brown rs232_RFID_TX White DGND Green CU0866: TGS / NFC cable (Low Kit / UI board connection) Patch connector Signal Colour Low Kit +5Vdc Black UI_TX Brown UI_RX White LKIT_RPM-SENSOR Blue GND_Power Grey N.C. (GND) N.C. (AUX_TX) N.C. (AUX_RX) Page 22 e-mail: support@technogym.com...
  • Page 23 Signal Colour Patch connector +5 Vdc Yellow UI_TX Brown UI_RX White Green Grey CU0884: Cable B - TGS / NFC (Patch connector/Patch connector) Patch connector Signal Colour Patch connector NFC_Power-ON Yellow rs232_RFID_RX Brown rs232_RFID_TX White DGND Green e-mail: support@technogym.com Page 23...
  • Page 24 Technical Service Guide - Rev. 2.2 CU0889: 5V JACK cable (Battery/5V jack) Battery Signal Colour 5V jack (Jack with cast cable) +5 Vdc Black CU0890: 5V USB cable (Battery/5V jack) Low Kit Signal Colour Battery +5 Vdc Black Page 24 e-mail: support@technogym.com...

  • Page 25: Operating Principle

    If the display is replaced, the QR Code sticker must be replaced. 3.1.3 DISPLAY (CONSOLE VERSION) In comparison to the Connect version display, the Console version display does not include the following: • WI-FI technology; • Display backlighting; • Keyboard backlighting; • Heart button not illuminated, drawn. e-mail: support@technogym.com Page 25...

  • Page 26: Low Kit

    This is the sensor that sends the horizontal speed of the treadmill to the Low Kit. When the CPU is powered and receives the speed signal, the display turns on. Based on the equipment characteristics, there can be two mechanical regulations: • if the pulley has standard screws without magnets, the distance between the RPM sensor and the nearest screw is D=0.8mm (D=0.0315”) (doing a complete revolution of the pulley, using a thick- ness gauge); For the Skillmill Console version, starting from SN DJK04D16000241 for the non-UL version and DJK14D16000003 for the UL version, the equipment has standard screws without magnets, whose distance between the RPM sensor and the nearest screw is D=0.8mm (D=0.0315”) (doing a complete revolution of the pulley, using a thickness gauge). Page 26 e-mail: support@technogym.com...
  • Page 27 Skillmill: Technical Service Guide - Rev. 2.2 D=0,8mm D=0,0315” Figure 7 • if the pulley has magnets (magnetic washer below the screws) the distance between the RPM sensor and the nearest magnet is D=0,5mm (D=0.0197”) (doing a complete revolution of the pulley, using a thickness gauge). D=0,5mm D=0,0197” Figure 8 e-mail: support@technogym.com Page 27...

  • Page 28: Angle Sensor

    The battery lasts 90 days with 4 hours of equipment operation per day. When the equipment is delivered, the battery charge level is between 40% and 60%. Before starting the equipment, completely charge the battery using the specific power supply. Page 28 e-mail: support@technogym.com...
  • Page 29 1-Remove the battery from its housing; 2-Disconnect the two connectors that connect the battery to the equipment; 3-Connect the power supply to the battery; 4-Let the battery charge for at least 16 hours; e-mail: support@technogym.com Page 29...
  • Page 30 If the battery is not used for a long period of time, check that the display is on and press the button (B); or disconnect the battery. To reactivate the battery, recharge it completely. Function of the button (B): • if the battery is off, the button turns it on; • if the battery is on, the button turns it off. Page 30 e-mail: support@technogym.com...

  • Page 31: Nfc (Connect Version)

    Display of the Skillmill class data in real time on the Mega screen/Monitor/Tv. Display of the Skillmill class data in real time on the Mega screen/Monitor/Tv: this function requires Unity Self with an HDMI output, starting from product E0202V15: UNITY SELF EXCITE HDMI and E0204V15 UNITY SELF ARTIS HDMI. The sw that manages the wi-fi can be updated. e-mail: support@technogym.com Page 31...
  • Page 32 Skillmill Technical Service Guide - Rev. 2.2 Blank page. Page 32 e-mail: support@technogym.com...

  • Page 33: Accessories

    Skillmill: Technical Service Guide - Rev. 2.2 ACCESSORIES For details, refer to the Marketing material. e-mail: support@technogym.com Page 33...
  • Page 34 Skillmill Technical Service Guide - Rev. 2.2 Blank page. Page 34 e-mail: support@technogym.com...

  • Page 35: Moving And Installing The Equipment

    “Skillmill - Assembly instructions” contained in the packaging. The area is not dusty or sandy. You have observed the temperature and humidity operating requirements indicated in para- graph: “2.2 Environmental characteristics” on page 14. e-mail: support@technogym.com Page 35...

  • Page 36: Lifting And Moving The Equipment

    Given the weight of the equipment, we recommend that more than one person be involved in the operation. ATTENTION: Moving and placing on the ground must be carried out with extreme care, because the equipment may lose stability. If wheels cannot be used on the floor, move the equipment with normal lifting and transport methods, according to what is shown in the distribution logistics installation video. Skillmill Figure 9 Page 36 e-mail: support@technogym.com...

  • Page 37: Troubleshooting & Configuration

    The first time that the PC is connected with Skillmill or New Group Cycle (D92) or MYRUN TECHNOGYM, the PC asks to install a driver for the detected device. Stop the automatic search for the driver on Windows update and select the manual path on your PC where the file was previously saved, which can be downloaded from TG Direct: myrun_usb_driver.inf.

  • Page 38: Structure For Entering Commands

    First Topic of the command (if required by the command) ARG2 Second Topic of the command (if required by the command) Message end marker (hash) Table 9 6.2.1 READING FIRMWARE VERSIONS 6.2.1.1 (CPU) FIRMWARE VERSION Command Notes Command @FWVER# Prints CPU firmware version. Table 10 Page 38 e-mail: support@technogym.com...

  • Page 39: Wi-Fi) Firmware Version

    Notes Command @LOWKITFWVER# Prints the version of the Low Kit firmware. Table 13 6.2.1.5 LOW KIT BRAKING TABLE VERSION Command Notes Prints the version of the braking table in the Command @LOWKITTBVER# Low Kit. Table 14 e-mail: support@technogym.com Page 39...

  • Page 40: Reading And Writing The Serial Numbers And Identification Parameters

    6.2.2.2 READING THE CONSOLE SERIAL NUMBER Command Notes Command @RCONSOLESN# Prints the console serial number. Table 16 6.2.2.3 SETTING THE FACILITY URL Command Notes Command @SFACILITYURL fc# Sets the facility URL of the equipment. Table 17 The parameter fc indicates the name of the facility URL of the equipment. Page 40 e-mail: support@technogym.com...

  • Page 41: Viewing The Facility Url

    6.2.2.5 WRITING THE LOW KIT SERIAL NUMBER Command Notes Command @SLOWKITSN sn# Sets the Low Kit serial number. Table 19 The parameter sn indicates the Low Kit serial number. It must have a length of 16 characters. 6.2.2.6 READING THE LOW KIT SERIAL NUMBER Command Notes Command @RLOWKITSN# Displays the Low Kit serial number. Table 20 e-mail: support@technogym.com Page 41...

  • Page 42: Determining Mac Address

    Command @SWIFIKEY key# the console must connect. Table 23 The parameter key indicates the value of the access point password. If the access point does not have a password, write only @WIFISETKEY#. 6.2.3.3 WRITING THE WEP KEY NUMBER Command Notes Sets the WEP key used to connect to the access Command @SWEPKEYINDEX index# point with WEP encryption. Table 24 Page 42 e-mail: support@technogym.com...

  • Page 43: Checking Connection Type

    6.2.3.5 WRITING THE CONSOLE IP ADDRESS Command Notes Command @SIPADDRESS ipaddress# Sets the console’s static IP address. Table 26 The parameter ipaddress indicates the static IP address of the console. 6.2.3.6 WRITING THE GATEWAY ADDRESS Command Notes Command @SDEFGATEWAY gateway# Sets the IP address of the default gateway. Table 27 The parameter gateway indicates the value of the IP address of the default gateway. e-mail: support@technogym.com Page 43...

  • Page 44: Checking The Ip Address - Default Gateway - Netmask

    Command @SRTMSOCKET ip_add port# realtime monitor is located. Table 30 The parameter ip_add indicates the IP address where the real-time monitor is located. The param- eter port indicates the number of the UDP power at which the real-time monitor is located. 6.2.4.2 SETTING THE DATA SEND PERIOD Command Notes Sets the data send period to the realtime mon- Command @SRTMPOLLING tsend# itor. Table 31 Page 44 e-mail: support@technogym.com...

  • Page 45: Displaying The Monitor Configuration

    Table 32 6.2.4.4 ENABLING DATA SENDING Command Notes Command @ENABLERTM# Enables sending data to the realtime monitor. Table 33 6.2.4.5 DISABLING DATA SENDING Command Notes Command @DISABLERTM# Disables sending data to the realtime monitor. Table 34 e-mail: support@technogym.com Page 45...

  • Page 46: Configuration And Settings For Classes: Skillmill App

    Set by default to “off”: the Skillmill app, if installed, is present in the standard Unity Self dashboard and the final user or the trainer must click on the “Skillmill” tile to use it. • When set to “on”: the Skillmill app starts automatically when Unity Self is turned on. To exit the Skillmill app, if set as the main app, press down on the screen in the top left area of the display, as shown in the following figure: Figure 11 Page 46 e-mail: support@technogym.com...

  • Page 47: Steps Necessary For Configuring The Skillmill Application

    TG Direct). Configure the consoles for the WiFi connection and for the connection with UNITY SELF (setting on the Technogym Equipment Set Up APP plus switching on of the console to store the data).

  • Page 48: Display Configuration (Connect Version)

    • time and distance (min:sec - km/mile); • heart frequency (bpm); • calories (kcal). Three types of displays are available: • instantaneous exercise values (while working out); • max values (at the end of the work out); • average values, kcal burned and move (at the end of the work out). Proceed as follows to change the display settings: • disconnect the power supply (Connect version) or switch off the battery (Console version); • power the display via the mini USB port; • 3 buttons appear when the equipment turns on (initial boot); • when the boot is complete, the buttons turn off and are active. The buttons are always active. It is useful to power the console via the USB socket to see the correct positioning of the buttons. Page 48 e-mail: support@technogym.com...
  • Page 49 Enters brake table calibration mode. Access the software update procedure (for de- tails, see paragraph: “9. SW Update” on page 67). LONG PRESS key This combo must be pressed when the display is off but the heart is illuminat- e-mail: support@technogym.com Page 49...

  • Page 50: Troubleshooting

    There are two possibilities - RPM not present - RPM not present - Effort level does not change - Effort level changes REPLACE THE LOW KIT / display low REPLACE the RPM sensor kit connection cable Page 50 e-mail: support@technogym.com...

  • Page 51: The Display Does Not Turn On (Console Version)

    There are two possibilities - RPM not present - RPM not present - Effort level does not change - Effort level changes REPLACE THE LOW KIT / display low REPLACE the RPM sensor kit connection cable e-mail: support@technogym.com Page 51...

  • Page 52: The Display Only Turns On At A High Speed

    Check the position of the RPM sensor Ok finished and move it close to the screws that it must detect. Is the problem solved? Replace the RPM sensor and the Ok finished connection cable. Is the problem solved? Replace the low kit Page 52 e-mail: support@technogym.com...

  • Page 53: The Effort Level Does Not Change On The Display

    If the display of the Skillmill Console version shows an abnormal speed (speed higher than the real value), try to execute the following procedure: - replace magnets with standard screws; - verify that the distance between the RPM sensor and the nearest screw is D=0.8mm (D=0.0315’’) (doing a complete revolution of the pulley, using a thickness gauge). e-mail: support@technogym.com Page 53...

  • Page 54: Login Problems

    Bluetooth If it does not pass to the the response from the cloud next channel, the problem is relative to the network, unity self configuration….. TGS/NFC The icon is off when no user is Bluetooth Login performed correctly. logged in (initial state) Qr code Page 54 e-mail: support@technogym.com...

  • Page 55: Bluetooth Login Problems

    Is the problem repeated on repeated on is probably not complies with the different equipment? different compatible minimum equipment? configuration Replace the Configure the display network on the Ok, done display. Is the problem solved? Replace display e-mail: support@technogym.com Page 55...

  • Page 56: Qr Code Login Problems

    Check that the serial number of the display read with the Replace terminal software corresponds with the serial number read on display the QR code with a QR reader. Are they the same? Set the correct number with the terminal software Page 56 e-mail: support@technogym.com...

  • Page 57: Tgs_Nfc Login Problems

    Replace the TGS/ NFC board Replace Configure the and the connection cable. display network on the Problem solved? Ok, done display. Is the problem solved? Ok, done Replace display e-mail: support@technogym.com Page 57...

  • Page 58: Brake Table Calibration

    Skillmill Technical Service Guide - Rev. 2.2 BRAKE TABLE CALIBRATION • Disconnect the external power supply (Connect version) or switch off the battery (Console version); • power the display with a PC or use a backup battery via the USB socket on the console; • long press of keys 1-2-3 (they must be pressed when the time stops flashing); CAL appears on the screen. • position the lever on the lowest braking (lever towards the rear of the equipment); • press the heart button, effort level indicated “0” will flash for a few moments and will become “1”; • move the lever forward (one click); • press the heart button, effort level indicated “1” will flash for a few moments and will become “2”; • proceed to level 10; • at the end of the procedure, END will appear and flash for a few moments; • disconnect the USB socket from the console; • reconnect the external power supply (Connect version) or switch on the battery (Console version). Page 58 e-mail: support@technogym.com...

  • Page 59: Disassembly

    Disconnect the two connectors. • Rubber hammer Loosen the screws fastening the handle- bar. • Long articulated T-handle wrench, 8 mm Remove the right guard. Remove the screws fastening the handle- bar (left side). Remove the handlebar by removing the screws (right side). e-mail: support@technogym.com Page 59...

  • Page 60: Disassembling The Side Handlebars

    Remove the front guard. Disassemble the braking system as indicated Remove the side guard. in paragraph “7.7.1 Disassembling the braking Disconnect the brake cable. system”. Remove the post. Remove the pulley and remove the cable from its seat. Page 60 e-mail: support@technogym.com...

  • Page 61: Replacing The Brake Disc And Pulley

    BRAKE FRAME Disassemble the brake disc and pulley as indi- cated in paragraph “7.7.4 Replacing the brake disc and pulley”. Mark the position of the brake frame with a marker. Remove the brake frame fastening screws. e-mail: support@technogym.com Page 61...

  • Page 62: Replacing The Platform

    Remove the nuts locking the right bearing. Remove the screws. Remove the flange. Remove the snap ring on the left side. To remove the shaft, align the two keys in the shaft with the holes present on the pulleys. Page 62 e-mail: support@technogym.com...

  • Page 63: Disassembling The Roller Bearings (Rear Zone)

    Remove the containment flange. Remove the board from the pin. Remove the belt from the pulley. The platform is free to move. Disassemble 13 slats as indicated in para- graph “7.8.1 Replacing the slats”. e-mail: support@technogym.com Page 63...
  • Page 64 Skillmill Technical Service Guide - Rev. 2.2 Blank page. Page 64 e-mail: support@technogym.com...

  • Page 65: Adjustments

    Skillmill: Technical Service Guide - Rev. 2.2 ADJUSTMENTS No adjustments are required. e-mail: support@technogym.com Page 65...
  • Page 66 Skillmill Technical Service Guide - Rev. 2.2 Blank page. Page 66 e-mail: support@technogym.com...

  • Page 67: Sw Update

    If asked (depending on the operating system installed) “Do you want to repair the content?” respond: “Continue without analysing”. Connect the upgrade USB key to the PC as soon as synchronised (with PC Synch): • Open the “Skillmill” folder on the synchronised USB key. • Drag the SW (file with the .bin extension) to the equipment folder. e-mail: support@technogym.com Page 67...
  • Page 68 Repeat the operations described above for all the software to be installed. Reposition the guard of the console's MINI USB connector. The “Skillmill” folder contains two sub-folders: • the sub-folder that contains 4 files applies to the Skillmill version Connect version. The SW has the following structure: high_kit_WFW----BA-----version; wifi_WFW----CA-----version; Low kit-----version; Table-----version. • the sub-folder that contains 3 files applies to the Skillmill version Console version. The SW has the following structure: high_kit_WFW----BA-----version; Low kit-----version; Table-----version. Page 68 e-mail: support@technogym.com...

  • Page 69: Planned Maintenance

    ROUTINE maintenance operations must also of the equipment. be carried out by Technogym technicians during planned maintenance visits. Refer to the Skillmill preventive maintenance Check List, available on TG DIRECT. Refer to the USER Manual. ROUTINE MAINTENANCE: MAJOR MAINTENANCE No technical specialisation required. Performed ONLY by a Qualified Technician authorised by Technogym and in accordance with the maintenance envisaged in the pre- ventive maintenance contract. e-mail: support@technogym.com Page 69...
  • Page 70 Skillmill Technical Service Guide - Rev. 2.2 Blank page. Page 70 e-mail: support@technogym.com...

  • Page 71: Tools To Be Used

    Skillmill: Technical Service Guide - Rev. 2.2 11. TOOLS TO BE USED The tools required to carry out all the disassembling, adjustment and maintenance operations on the equipment are given in the TG SERVICE TOOLS BOX LIST, available on TG DIRECT and during the training course on the e-learning platform. e-mail: support@technogym.com Page 71...
  • Page 72 Blank page.

  • Page 73: List Of Changes For Manual Revision

    §9 - SW update: change to pop-up figure; change to point 2. §10 - Planned maintenance. 12.3 REVISION 2.1 §1.2: New paragraph “Useful advice”. §6.3.1: Change to steps necessary for configuring the Skillmill application. §6.1: Executable SW for diagnostics with PC e-mail: support@technogym.com Page 73...
  • Page 74 Changed Paragraph 2.2 Environmental Characteristics, 3.1.10 WiFi (connect version), 5.2 Lifting and moving the equipment, 9 SW update, 3.1.5 RPM Sensor. Insert the new Paragraph 6.5.6 The display shows an abdormal speed (console version). Paragraph “WI-FI connection” eliminated because it is redundant. Page 74 e-mail: support@technogym.com...
  • Page 76 TECHNOGYM S.p.A. Via Calcinaro, 2861 - 47521 Cesena (FC) - Operational Headquarters ITALY Tel.: +39-0547-650638 Fax: +39-0547-650150 e-mail: support@technogym.com 0SM00931AA-UK...

This manual is also suitable for:

Skillmill connectSkillmill console

Table of Contents