Download Print this page
Cleco 75 Series Operation & Service Manual

Cleco 75 Series Operation & Service Manual

Fixturized nutrunners
Hide thumbs Also See for 75 Series:

Advertisement

Quick Links

75 Series Fixturized Nutrunners
Series:
75
Rotation:
Non Reversible
R
Reversible
Motor:
Torque Control Mechanism:
A
Clecomatic
Stall Type
T
Transducer
J
Joint Rate
Handle:
L
Lever
SL
Lock-Off Lever
NORTH AMERICA
CooperTools
P.O. Box 1410
Lexington, SC 29071
75
X M X XX
-
X
XXX
V
X
VHD
LS
LR
OS200 200Nm Off-Set Spindle
R6
R8
Operation & Service Manual
823076
-
X
-
X
-
X
Output Drive:
4
Terminations:
5
6
Hold & Drive
Solid Spindle
Retractable Spindle
6" Transducer Spindle
8" Non-Transducer Spindle
Gear Train Designation:
2
4
3
5
EUROPE
Cooper Power Tools GmbH & Co.
Postfach 30
D-73461 Westhausen
2/01
Output Drive for LS & LR:
13/16
13
2
2
1/2"
3 3/4
3 - 6
5/8"
3/4"
1

Advertisement

loading
Need help?

Need help?

Do you have a question about the 75 Series and is the answer not in the manual?

Questions and answers

Summary of Contents for Cleco 75 Series

  • Page 1 Operation & Service Manual 823076 2/01 75 Series Fixturized Nutrunners X M X XX Series: Output Drive for LS & LR: 13/16 Output Drive: Rotation: 1/2" 3 3/4 3 - 6 Non Reversible Terminations: 5/8" Reversible 3/4" Hold & Drive...
  • Page 2: Safety Recommendations

    Cleco tools are designed to operate on 90 psig (6.2 bar) or any other disorder of the shoulders, arms, wrists, or maximum air pressure. If the tool is properly sized and fingers is advised to consult a physician.
  • Page 3 Safety Recommendations The following suggestions will help reduce or moderate the Work gloves with vibration reducing liners and wrist sup- effects of repetitive work motions and/or extended vibra- ports are available from some manufacturers of industrial tion exposure: work gloves. Tool wraps and grips are also available from •...
  • Page 4 lightly in the vise and unscrew the rotor lock nut. Rest the rear OPERATING INSTRUCTIONS bearing plate on the vise jaws and use a soft faced mallet to drive the rotor out of the rear rotor bearing. The 75 Nutrunner is designed to operate on 90 PSIG (6.2 bar) air Handle pressure using a 1/2"...
  • Page 5: Transducer Specifications

    2(Rcal) + Rbr Where Rcal = Calibration Resistor Value in ohms of the torque monitor used. The following is an example of a 75 series right angle tool, a "V" head and a torque monitor with a 110,000 ohm calibration resistor.
  • Page 6 75 R8 FIXTURE MOUNTED TOOL SPINDLE SUBASSEMBLIES 203485 (Req. 2) 864471 202958 5/8" OPT. 203207 202918 1/2" STD. 202936 202933 843179 202915 202920 202934 864710 203198 864710 5/8" 844013 1/2" 864712 5/8" 844014 1/2" 864711 5/8" 844011 1/2" PARTS LIST — R8 SPINDLE SUBASSEMBLIES PART NO.
  • Page 7 75 R6 FIXTURE MOUNTED TOOL TRANSDUCERIZED SPINDLE SUBASSEMBLIES 202957 (2Req.) 864471 202930 202912 Std. 202925 202966 843179 202967 863093 202968 202976 3/8" *202932 (4Req.) 202918 1/2" 202914 202915 *203000 *202931 202920 844013 3/8" 844013 1/2" 844017 3/8" 844014 1/2" 844016 3/8"...
  • Page 9 75 FIXTURE MOUNTED OS200 OFFSET SPINDLE PARTS LIST — OFFSET SPINDLE — OS200 PART NO. NAME OF PART QTY. PART NO. NAME OF PART QTY. 548151 GEAR HOUSING 546058 LOWER IDLER SPACER 548261 843179 MOTOR SHAFT RETAINER RING 548262 GEAR CASE ADAPTOR 882507 NEEDLE BEARING 548067...
  • Page 10 847659 869877 869878 869879 "V" & "X" RIGHT ANGLE HEADS 869882 "V" 883720 "X" 869874 "V" 861903 "V" 867546 869875 "X" 869880 861905 "X" 864711 864710 864712 867997 861903 "V" 869886 "V" 1/2" 869881 "V" 869876 "V" 861905 "X" 869883 "V" 5/8" 812222 "X"...
  • Page 11 75 M, MT, RM & MA FIXTURE MOUNTED TOOL GEAR TRAINS Part No. Model Part No. Model Part No. Model 869907 869908 869900 869907 869908 869900 869907 869908 869899 869907 869908 869899 Part No. Model 869902 Part No. Model 869903 NONE 869902 NONE...
  • Page 12 75 CLECOMATIC CLUTCH 869920 202057 869916 869921 869913 842161 869914 847022 869915 867670 202056 867666 842161 869626 867669 867683 869917 847528 869919 869918 869912 842162 PARTS LIST — 75 CLECOMATIC CLUTCH PART NO. NAME OF PART QTY. PART NO. NAME OF PART QTY.
  • Page 13 75 M, MT, MA, RM & MSL FIXTURE MOUNTED TOOL MOTOR UNITS 617754 Trans. Models Only 203197 Trans. 203147 869923 Non-Trans. 847603 Revsible Only 812918 865352 847528 847960 Alll Models 203149 Non-Rev. 869925 Non-Rev. 847528 Except MA 203148 Rev. 869928 Rev.
  • Page 14 75 M, RM, MT & MA FIXTURE MOUNTED TOOL MOTOR HOUSINGS 867758 NON-REV. 202495 REV. (QTY.2) 869943 615018 202050 615018 867732 202051 202957 843434 NON -REV. 843434 TRANS. AIR SIGNAL 202601 PORT ONLY 202603 AUTOMATIC 843434 842161 SHUT-OFF ONLY 869938 863880 869937 203196...
  • Page 15 75 MSL FIXTURE MOUNTED MOTOR HOUSING 869943 615018 202050 615018 203416 PART NO. NAME OF PART QTY. 202050 Deflector Spacer 202970 MSL Motor Housing 203416 Exhaust Deflector (MSL Model) 615018 Exhaust Deflector "O"-ring 2-1/2" x 2-5/8" 869943 Muffler 202970 615018 75 MSL FIXTURE MOUNTED LOCK OFF LEVER HANDLE PART 867769-2...
  • Page 16 75 HANDLE 864973 202508 869931 869933 622881 843656 202055 AND MOTOR 622062 RMAL, MAL, RML, 869942 ML & MJL NUTRUNNERS 202050 Rev. Tools 202051 869943 615018 615018 Only 864195 865063 869938 Automatic Shut-off Tools Only 203150 Non-Rev. 203151 Rev. 869936 202481 863880 Non-reversible...
  • Page 17 NOTES...
  • Page 18 NOTES...
  • Page 19 NOTES...
  • Page 20 CooperTools 670 Industrial Drive Lexington, SC 29072 Phone: (803) 359-1200 Fax: (803) 359-2013 www.cooperindustries.com...