Page 1
Quick Installation Guide P2600KA-EN REV B | 2023-07 CLBA & CLBP Data Transmission For additional product information visit our website at www.ClecoTools.com...
Page 2
Disclaimer Apex Tool Group reserves the right to modify, supplement, or improve this document or the product with- out prior notice. Trademark Cleco® is a registered trademark of Apex Brands, Inc. Apex Tool Group 670 Industrial Drive Lexington, SC 29072...
Content About this Document ................4 Other Documents ......................4 Symbols in the Text ......................4 System Layout ..................5 WLAN communication ....................5 2.1.1 Tool Data ........................5 2.1.2 Country-specific channel settings ................... 6 2.1.3 Cell planning for access point ..................7 Before Initial Operation ................
About this Document About this Document This document is intended for qualified employees responsible for installation and maintenance (adminis- trators, installers, maintenance technician, service, operator). It contains information for save, appropriate installation and handling. This document is not sufficient for planning complex •...
System Layout System Layout The communication between the controller and the tool is possible via WLAN or Bluetooth. The tool can communicate with a mPro200GC-AP or mPro400GCD controller. The model name of WLAN or Bluetooth enabled tools has a "W" in the 5th position of the name and ends with a country abbreviation.
System Layout 2.1.2 Country-specific channel settings The tools work in the license-free 2.4 GHz/5 GHz ISM band. Band Channel Frequency in World Europe USA/ China Canada World 2.4 GHz 2.412 IEEE802.11b/g 2.417 2.422 2.427 2.432 2.437 2.442 2.447 2.452 2.457 2.462 2.467 –...
System Layout Band Channel Frequency in World Europe USA/ China Canada World 5 GHz 5.745 – – U-NII-3 5.765 – – 5.785 – – 5.805 – – 5.825 – – Legend x: Approved and available -: Not permissible, blocking necessary o: Permissible with limited power to 20 dBm (SRD) 2.1.3 Cell planning for access point...
Page 8
System Layout SSID 2 SSID 3 SSID 4 SSID 5 SSID 7 SSID 6 SSID 8 SSID 9 Fig. 2-4: Idealized radio cells = Range of use of the tools, channel 60 P2600KA | REV B | 2023-07 Apex Tool Group...
Before Initial Operation Before Initial Operation Requirements Laptop/PC with: • Operating system: Windows 10, 64 Bit Screen resolution: 1280 x 768 or higher Software CLPC100 • • Software S168691 mProRemote Professional Monitor with VGA connector, keyboard and mouse (optional) • Micro-B USB cable •...
Initial operation Initial operation The CellClutch tool and the tightening sequence are configured with the CLPC100 software. Configuring the access point 4.1.1 mPro200GC-AP In the factory setting, the IP address and the subnet mask of the controller are specified with a default value (Ethernet 1): Parameter Default value...
Initial operation Parameter Description Activate WLAN Communi- If the checkbox is activated, WLAN is enabled on the controller. cation The bluetooth function is deactivated. SSID Enter the SSID for the WLAN name (access point) to which a connection is to be established.
Initial operation Configuring RF settings The tool RF settings can be configured with a laptop/PC. Perform the following steps only when WLAN communication is to be established. Connect the tool to the laptop/PC via USB Connect the tool to the laptop/PC via a Micro-B USB cable. Fig.
Page 13
Initial operation The WLAN settings on the tool are configured via the CLPC100 software. This function is only possible with WLAN compatible CellClutch tools. The Model name of WLAN-capable tools has a "W" in the 5th po- sition of the name and ends with a country abbreviation. Example: Tool model without WLAN Tool model with WLAN...
Initial operation Parameter Description Security Select security. Security must be identical to the access point. Network Key Enter the network key. The network key must be identical to the access point. User Enter a username. Password Enter a password. Regulatory Domain Specifies country-specific channel settings.
Page 15
Initial operation The Tool List is displayed. Status of tool is now Online. To save the settings, select <Navigator>. For additional programming for tightening (e.g., PG), see document P2280PM. Apex Tool Group P2600KA | REV B | 2023-07...
Page 16
POWER TOOLS SALES & SERVICE CENTERS Please note that all locations may not service all products. Contact the nearest Cleco® Sales & Service Center for the appropriate facility to handle your service requirements. Sales Center Service Center NORTH AMERICA | SOUTH AMERICA...
Need help?
Do you have a question about the CellClutch CLBA and is the answer not in the manual?
Questions and answers