American National Standards Institute, ANSI S12.6, Hearing Protec- tors. Cleco nutrunners are designed to operate on 90 psig (6.2 bar) maximum air pressure. If the tool is properly sized and applied, higher air pressure is unnecessary. Excessive air pressure in- creases the loads and stresses on the tool parts, sockets, and fasteners and may result in breakage.
Page 3
Safety Recommendations The following suggestions will help reduce or moderate the effects WARNING of repetitive work motions and/or extended vibration exposure: Repetitive work motions and/or vibration may cause injury to hands and arms. • Use a minimum hand grip force consistent with proper Use minimum hand grip force consistent control and safe operation with proper control and safe operation.
Page 4
Safety Recommendations ADDITIONAL SAFETY RECOMMENDATIONS FOR USE OF RIGHT For more information on the safe use of portable air tools, see the ANGLE DRILLS latest edition of ANSI B186.1, Safety Code for Portable Air Tools, available from the American National Standards Institute, Inc. 11 West 42nd Street, New York, NY 10036.
Page 5
3/4" or larger hose should be connected to the 1/2" hose. OPERATING INSTRUCTIONS The air hose should be cleared of accumulated dirt and moisture, then one (1) teaspoonful of 10W machine oil should be pou- red into the tool's air inlet before connecting The No.
Page 6
Stall Type Tools Motor Clamp the flats of the handle in a vise with the tool in a Use a soft faced mallet to drive the rotor out of the front rotor vertical position. bearing, No. 847528. This will allow the removal of the front bearing plate, No.
1st REDUCTION GEAR TRAIN REASSEMBLY "V" Right Angle Head = 3- 3/16" (81mm) "X" Right Angle Head = 3" (76.2mm) - 2 Gear Train (13 Tooth Spider) 21 Tooth idler gears on inner set of gear pins. The pinion bearing retainer, No. 869877, should be tight- ened to 35 to 40 ft.
Page 8
"V" & "X" 847659 869877 869878 869879 RIGHT ANGLE HEADS 869882 "V" 883720 "X" 869874 "V" 861903 "V" 867546 869875 "X" 869880 861905 "X" 864711 864710 864712 867997 861903 "V" 869886 "V" 1/2" 869881 "V" 869876 "V" 861905 "X" 869883 "V" 5/8" 812222 "X"...
Page 9
75 NUTRUNNER GEAR TRAINS Part No. Model Part No. Model Part No. Model 869907 869908 869900 869907 869908 869900 869907 869908 869899 869907 869908 869899 Part No. Model 869902 Part No. Model 869903 NONE 869902 NONE 832125 869903 869901 869901 844774 Part No.
Page 10
75 NUTRUNNER CLECOMATIC CLUTCH 869920 202057 869916 869921 869913 842161 869914 847022 869915 867670 202056 867666 842161 869626 867669 867683 869917 847528 869919 869918 869912 842162 PARTS LIST — 75 CLECOMATIC CLUTCH PART NO. NAME OF PART QTY. PART NO. NAME OF PART QTY.
Page 11
864973 202508 75 NUTRUNNER 869931 869933 622881 843656 202055 622062 HANDLE AND MOTOR 869942 H202050 Rev. Tools 202051 869943 615018 615018 Only 864195 865063 869938 Automatic Shut-off Tools Only H203150 Non-Rev. 203151 Rev. 869936 202481 863880 Non-reversible Automatic Shut-off Tools Only 869937 867554 617510...
Page 12
"V" RIGHT ANGLE HOLD & DRIVE HEAD 847659 869877 869878 869879 867924 204384 867546 869880 204385 864711 864712 864710 867997 204350 204349 204346 622772 204344 842160 617290 204355 204345 PART NO. DESCRIPTION QTY. 204344 DRIVE SPINDLE 204345 BEARING CAP 204346 HOLD SPINDLE 204347 CLAMP RING†...
Need help?
Do you have a question about the 75 Series and is the answer not in the manual?
Questions and answers