Maintenance; Cleaning The Appliance; Error Detection - Champion CHDS210 User Manual

• Switch off the vacuum cleaner by pressing the ON/Off button once (8) and unplug the power cord (14) from the power socket.
• Press the automatic cord winding button (15) to wind the power cable [FIG. F1]. Hold the plug while winding the cable in
order to prevent whiplash.
1. Press the locking buttons of the flexible suction pipe (6) and disconnect the flexible suction pipe (5) from the appliance.
2. Press the release button of the dust collection system (9) to extract the dust collection system (16) from the appliance [G1].
EN
3. Press the upper cover opening/locking button (16B) to open the upper cover (16A) [FIG. G2].
4. Empty the container.
5. Fit the upper cover back on (16A) ensuring the couplings with the dust container (16E) are perfectly engaged and the upper
cover opening/locking button (16B) is perfectly engaged as well.
6. Fit the dust collection system (16) back onto the vacuum cleaner ensuring the position
ATTENTION! The vacuum cleaner has a motor protection thermostat, which intervenes in the case of overheating (caused by the inlet opening,
filters, etc. being clogged). If it is triggered, press the ON/OFF (8) button to switch the appliance off and let it cool down completely for a few hours.
Verify whether dust has clogged the filters or the inlet opening before restarting the appliance.
ATTENTION! S witch the appliance off and disconnect the plug from the socket before opening the appliance! Make sure all cleaned parts are
completely dry before reusing the appliance.

Maintenance

• When necessary, clean the appliance with a damp cloth.
• Cleaning the combination brush (4): With the motor ON, rub the brush with your hand to remove the dust and fluff, which
will be drawn in.
• Cleaning the dust collection system (16): Clean the dust collection system following the instructions below, paying
attention to the pictures in the illustrative guide.

Cleaning the appliance

ATTENTION! DO NOT USE SOLVENTS OR OTHER AGGRESSIVE OR ABRASIVE DETERGENTS. OTHERWISE, THIS MAY DAMAGE THE SURFACE.
ATTENTION! Empty the dust container (16E) and clean the HEPA premotor filter (16D) after each use. Lock clicks.
Cleaning or replacing the promotor HEPA filter (16D)
1. Press the release button of the dust collection system (9) to extract the dust collection system (16) from the appliance [FIG. G1].
2. Remove the HEPA premotor filter (16D) from the dust collection system (16) [FIG. G3].
3. If the HEPA premotor filter (16D) is obstructed by dust, remove the dust taking care not to damage it. If the filter is especially dirty, replace
it with a new one.
4. Fit the HEPA premotor filter (16D) back onto the dust collection system (16) taking care to push the frame until the top appendix closes the
safety interlock (16C).
5. Fit the dust collection system (16) onto the vacuum cleaner ensuring the position lock clicks.
Cleaning or replacing the outlet filter (16)
1. Press the release/locking button of the outlet filter grid (20) to remove the outlet filter grid (19).
2. Extract the outlet filter (18) [FIG. G4].
3. If the outlet filter (18) is obstructed by dust, remove the dust taking care not to damage it. If the filter is especially dirty, replace it with a
new one.
4. Refit the outlet filter (18) in the appliance [FIG. G4].
5. Fit the outlet filter grid back on (19) and click the coupling/locking button of the outlet filter grid in position (20).

Error detection

Before you contact our services center, please check the following points:
PROBLEM
The appliance does not start.
The appliance turns off during use and does not turn on again.
SOLUTION
• Ensure the power cord (14) is connected to the power socket.
• Ensure the ON/Off switch (8) has been pressed [FIG. F1].
• The vacuum cleaner is equipped with a protective motor thermostat
that shuts off the appliance in the event of overheating! (caused by
obstructing objects or a clogged dust collection system). In the event of
this, press the ON/Off switch, unplug the power cord (14) from the power
socket and let the vacuum cleaner cool down completely. Remove any
dust or the obstructing object before restarting the appliance.