Epic motherboard with intel atom processor, vga, dual lvds, gbe lan, eight usb 2.0, two sata 3gb/s, four rs-232, rs-232/422/485, pcie mini, pci-104, rohs (147 pages)
Epic sbc with 3rd generation 22nm intel mobile cpu up to 8.0 gb ddr3, dvi,hdmi, lvds, dual gbe, sata 6gb/s, usb 3.0, pcle mini, intel atm,rohs (191 pages)
NANO-HM651 EPIC SBC IEI Technology Corp. MODEL: NANO-HM651 EPIC SBC with Intel® Celeron® 847E Dual-Core CPU and Intel® HM65 Chipset, DDR3, VGA, HDMI, USB 3.0, Dual PCIe GbE, SATA 6Gb/s, HD Audio, RoHS Compliant User Manual Page i Rev. 1.00 – 10 September, 2012...
Page 2
NANO-HM651 EPIC SBC Revision Date Version Changes 10 September, 2012 1.00 Initial release Page ii...
Page 3
NANO-HM651 EPIC SBC Copyright COPYRIGHT NOTICE The information in this document is subject to change without prior notice in order to improve reliability, design and function and does not represent a commitment on the part of the manufacturer. In no event will the manufacturer be liable for direct, indirect, special, incidental, or consequential damages arising out of the use or inability to use the product or documentation, even if advised of the possibility of such damages.
Page 5
NANO-HM651 EPIC SBC 3.2.12 Power Connector ................... 26 3.2.13 SATA 6Gb/s Connector................... 27 3.2.14 SATA Power Connectors ................28 3.2.15 Serial Port Connectors (COM 1 and COM 2) ..........28 3.2.16 Serial Port Connector (COM3) ..............29 3.2.17 SMBus Connector ..................30 3.2.18 SPI Flash Connector..................
Page 6
NANO-HM651 EPIC SBC 4.8.5 USB Cable (Optional)..................55 4.9 E ........... 56 XTERNAL ERIPHERAL NTERFACE ONNECTION 4.9.1 HDMI Display Device Connection ..............57 4.9.2 LAN Connection....................58 4.9.3 USB Connection....................58 4.9.4 VGA Monitor Connection ................59 4.10 S ..................60...
Page 7
NANO-HM651 EPIC SBC A BIOS OPTIONS ......................93 B ONE KEY RECOVERY ..................... 96 B.1 O ..............97 ECOVERY NTRODUCTION B.1.1 System Requirement..................98 B.1.2 Supported Operating System ................99 B.2 S ................ 100 ETUP ROCEDURE FOR INDOWS B.2.1 Hardware and BIOS Setup ................101 B.2.2 Create Partitions ...................
Page 8
NANO-HM651 EPIC SBC D.3.1 Enable the DIO Input Function ..............144 D.3.2 Enable the DIO Output Function..............144 E WATCHDOG TIMER....................145 F HAZARDOUS MATERIALS DISCLOSURE............148 F.1 H IPB P AZARDOUS ATERIALS ISCLOSURE ABLE FOR RODUCTS ERTIFIED AS HS C 2002/95/EC W ........
Page 14
NANO-HM651 EPIC SBC BIOS Menus BIOS Menu 1: Main ........................65 BIOS Menu 2: Advanced ......................66 BIOS Menu 3: ACPI Configuration ....................67 BIOS Menu 4: TPM Configuration ....................68 BIOS Menu 5: CPU Configuration ....................69 BIOS Menu 6: SATA Configuration .....................70 BIOS Menu 7: USB Configuration ....................71 BIOS Menu 8: Super IO Configuration..................72...
SSD. The PCIe Mini slot allows an mSATA card to be installed. The NANO-HM651 also comes with two Gigabit Ethernet (GbE) connectors, two USB 3.0 connectors and two USB 2.0 connectors. Serial device connectivity is provided by two internal RS-232 connectors and one internal RS-422/485 connector.
NANO-HM651 EPIC SBC 1.3 Dimensions The dimensions of the board are listed below: Length: 115 mm Width: 165 mm Figure 1-3: NANO-HM651 Dimensions (mm) Page 4...
NANO-HM651 EPIC SBC 1.4 Data Flow F igure 1-4 shows the data flow between the two on-board chipsets and other components installed on the motherboard and described in the following sections of this chapter. Figure 1-4: Data Flow Block Diagram...
NANO-HM651 EPIC SBC 1.5 Technical Specifications NANO-HM651 technical specifications are listed in table below. Specification NANO-HM651 EPIC Form Factor Intel® Celeron® dual-core 847E processor 1.1GHz CPU Options Intel® HM65 System Chipset Graphics Engine Intel® HD Graphics Gen 6 support for DX10.1 and OpenGL 3.0...
NANO-HM651 EPIC SBC Specification NANO-HM651 Two external USB 2.0 ports USB Ports Two external USB 3.0 ports (via ASMedia ASM1042 USB 3.0 extended host controller) Keyboard/Mouse One keyboard and mouse connector via internal 6-pin header SMBus One 4-pin wafer connector...
Only handle the edges of the PCB: Don't touch the surface of the motherboard. Hold the motherboard by the edges when handling. 2.2 Unpacking Precautions When the NANO-HM651 is unpacked, please do the following: Follow the antistatic guidelines above. Make sure the packing box is facing upwards when opening.
If any of the components listed in the checklist below are missing, do not proceed with the installation. Contact the IEI reseller or vendor the NANO-HM651 was purchased from or contact an IEI sales representative directly by sending an email to ales@iei.com.tw.
NANO-HM651 EPIC SBC Enclosure heatsink Mini jumper pack Utility CD One Key Recovery CD Quick Installation Guide 2.3.2 Optional Items The following component is optional: Item and Part Number Image Dual USB cable (wo bracket) (P/N: 32000-070301-RS) Page 11...
NANO-HM651 EPIC SBC 3.1.2 Peripheral Interface Connectors T able 3-1 shows a list of the peripheral interface connectors on the NANO-HM651. Detailed descriptions of these connectors can be found below. Connector Type Label Audio connector 10-pin header AUDIO1 Battery connector...
NANO-HM651 EPIC SBC 3.1.3 External Interface Panel Connectors T able 3-2 lists the rear panel connectors on the NANO-HM651. Detailed descriptions of these connectors can be found in Section 3 .3 on page 3 2. Connector Type Label Ethernet connectors...
NANO-HM651 EPIC SBC Description Battery+ Ground Table 3-4: Battery Connector Pinouts 3.2.3 Digital Input/Output (DIO) Connector CN Label: DIO1 CN Type: 10-pin header (2x5) CN Location: See Figure 3-4 CN Pinouts: See Table 3-5 The digital input/output connector is managed through a Super I/O chip. The DIO connector pins are user programmable.
NANO-HM651 EPIC SBC 3.2.5 Fan Connector (CPU) CN Label: CPU_FAN1 4-pin wafer (1x4) CN Type: CN Location: F igure 3-6 CN Pinouts: T able 3-7 The cooling fan connector provides a 12V, 500mA current to the cooling fan. The connector has a "rotation" pin to get rotation signals from fans and notify the system so the system BIOS can recognize the fan speed.
NANO-HM651 EPIC SBC CN Location: F igure 3-7 CN Pinouts: T able 3-8 The cooling fan connector provides a 12V, 500mA current to the cooling fan. The connector has a "rotation" pin to get rotation signals from fans and notify the system so the system BIOS can recognize the fan speed.
NANO-HM651 EPIC SBC CN Pinouts: See Table 3-13 The PCIe Mini card slot enables a PCIe Mini card expansion module to be connected to the board. Cards supported include among others wireless LAN (WLAN) cards and mSATA cards. Figure 3-12: PCIe Mini Card Slot Location...
NANO-HM651 EPIC SBC Description Description USBD+ 1.5V VCC3 Table 3-13: PCIe Mini Card Slot Pinouts 3.2.12 Power Connector CN Label: PWR1 CN Type: 4-pin connector (2x2) CN Location: See Figure 3-13 CN Pinouts: See Table 3-14 This connector accepts 12 V of power for the processor.
NANO-HM651 EPIC SBC Description Description +12 V +12 V Table 3-14: CPU Power Connector Pinouts 3.2.13 SATA 6Gb/s Connector CN Label: S_ATA1, S_ATA2 CN Type: 7-pin SATA drive connector CN Location: F igure 3-14 CN Pinouts: T able 3-15 The SATA connectors connect to SATA hard drives or optical drives with data transfer speeds as high as 6Gb/s.
NANO-HM651 EPIC SBC 3.2.14 SATA Power Connectors CN Label: CN1, CN2 2-pin wafer CN Type: CN Location: See Figure 3-15 CN Pinouts: See Table 3-16 Use the SATA Power Connector to connect to SATA device power connections. Total +5V SATA power is 2A (CN1+CN2).
NANO-HM651 EPIC SBC Figure 3-17: Serial Port Connector Location Description RXD422- RXD422+ TXD422+/TXD485+ TXD422-/TXD485- Table 3-18: Serial Port Connector Pinouts Use the optional RS-422/485 cable to connect to a serial device. The pinouts of the DB-9 connector are listed below.
SPI_CLK_SW Table 3-21: SPI Flash Connector 3.3 External Peripheral Interface Connector Panel F igure 3-20 shows the NANO-HM651 external peripheral interface connector (EPIC) panel. The NANO-HM651 EPIC panel consists of the following: 2 x RJ-45 LAN connectors 2 x HDMI connectors 2 x USB 2.0 connectors...
CN Pinouts: T able 3-22 The NANO-HM651 is equipped with two built-in RJ-45 Ethernet controllers. The controllers can connect to the LAN through two RJ-45 LAN connectors. There are two LEDs on the connector indicating the status of LAN. The pin assignments are listed in the...
NANO-HM651 EPIC SBC CN Location: F igure 3-20 CN Pinouts: T able 3-25 The NANO-HM651 has two external USB 2.0 ports. The ports connect to both USB 2.0 and USB 1.1 devices. Description DATA- DATA+ Table 3-25: USB 2.0 Port Pinouts 3.3.4 USB 3.0 Connectors...
15-pin Female CN Type: CN Location: F igure 3-20 CN Pinouts: F igure 3-23 and T able 3-27 The NANO-HM651 has a single 15-pin female connector for connectivity to standard display devices. Figure 3-23: VGA Connector Description Description GREEN BLUE...
Electrostatic discharge (ESD) can cause serious damage to electronic components, including the NANO-HM651. Dry climates are especially susceptible to ESD. It is therefore critical that whenever the NANO-HM651 or any other electrical component is handled, the following anti-static precautions are strictly adhered to.
NANO-HM651 is installed. All installation notices pertaining to the installation of the NANO-HM651 should be strictly adhered to. Failing to adhere to these precautions may lead to severe damage of the NANO-HM651 and injury to the person installing the CPU card. WARNING:...
NANO-HM651 EPIC SBC Before and during the installation of the NANO-HM651 DO NOT: Remove any of the stickers on the PCB board. These stickers are required for warranty validation. Use the product before verifying all the cables and power connectors are properly connected.
0: 4.5 Heat Sink Enclosure WARNING: Never run the NANO-HM651 without the heat sink secured to the board. The heat sink ensures the system remains cool and does not need addition heat sinks to cool the system. Page 41...
When the NANO-HM651 is shipped it is secured to a heat sink with eight retention screws. If the NANO-HM651 must be removed from the heat sink, the eight retention screws must be removed.
OPEN a jumper means removing the plastic clip from a jumper. Before the NANO-HM651 is installed in the system, the jumpers must be set in accordance with the desired configuration. The jumpers on the NANO-HM651 are listed in T able 4-1.
Jumper Location: F igure 4-5 If the NANO-HM651 fails to boot due to improper BIOS settings, the clear CMOS jumper clears the CMOS data and resets the system BIOS information. To do this, use the jumper cap to close pins 2 and 3 for a few seconds then reinstall the jumper clip back to pins 1 and 2.
NANO-HM651 EPIC SBC Load Failsafe Defaults. After having done one of the above, save the changes and exit the CMOS Setup menu. The clear CMOS jumper settings are shown in T able 4-3. Setting Description Short 1 - 2 Keep CMOS Setup (Default)
NANO-HM651 EPIC SBC The LCD voltage selection jumper sets the voltage of the power supplied to the LCD panel. Setting Description Short 1-2 +3.3 V (Default) Short 2-3 +5.0 V Table 4-4: LVDS Voltage Selection Jumper Settings Figure 4-6: LVDS Voltage Selection Jumper Location 4.6.4 LVDS Panel Resolution Selection Jumper...
NANO-HM651 EPIC SBC Description 3-4 and 5-6 1600 X 1200 (48bit) 1-2 and 3-4 and 5-6 1280 X 768 (18bit) 1280 X 800 (18bit) 1-2 and 7-8 1366 X 768 (24bit) 3-4 and 7-8 1440 X 900 (48bit) 1-2 and 3-4 and 7-8...
The NANO-HM651 must be installed in a chassis with ventilation holes on the sides allowing airflow to travel through the heat sink surface. In a system with an individual power supply unit, the cooling fan of a power supply can also help generate airflow through the board surface.
This section outlines the installation of peripheral devices to the onboard connectors. 4.8.1 AT Power Connection Follow the instructions below to connect the NANO-HM651 to an AT power supply. WARNING: Disconnect the power supply power cord from its AC power source to prevent a sudden power surge to the NANO-HM651.
NANO-HM651 EPIC SBC Figure 4-10: Power Cable to Motherboard Connection Step 3: Connect Power Cable to Power Supply. Connect one of the 4-pin (1x4) Molex type power cable connectors to an AT power supply. See Figure 4-11. Page 51...
Figure 4-11: Connect Power Cable to Power Supply 4.8.2 Audio Kit Installation The Audio Kit that came with the NANO-HM651 connects to the audio connector on the NANO-HM651. The audio kit consists of three audio jacks. Mic-in connects to a microphone.
0: 4.8.3 SATA Drive Connection The NANO-HM651 is shipped with a SATA drive cable. To connect the SATA drive to the connector, please follow the steps below. Step 1: Locate the SATA connector and the SATA power connector. The locations of the connectors are shown in Chapter 3.
NANO-HM651 EPIC SBC Figure 4-13: SATA Drive Cable Connection Step 3: Connect the cable to the SATA disk. Connect the connector on the other end of the cable to the connector at the back of the SATA drive. See Figure 4-13.
Step 0: 4.8.5 USB Cable (Optional) The NANO-HM651 is shipped with a dual port USB 2.0 cable. To connect the USB cable connector, please follow the steps below. Step 1: Locate the connectors. The locations of the USB connectors are shown in Chapter 3.
NANO-HM651 EPIC SBC Step 3: Insert the cable connectors. Once the cable connectors are properly aligned with the USB connectors on the NANO-HM651, connect the cable connectors to the on-board connectors. See Figure 4-15. Figure 4-15: Dual USB Cable Connection Step 4: Attach the USB connectors to the chassis.
NANO-HM651 EPIC SBC 4.9.1 HDMI Display Device Connection The HDMI connector transmits a digital signal to compatible HDMI display devices such as a TV or computer screen. To connect the HDMI cable to the NANO-HM651, follow the steps below. Step 1: Locate the HDMI connector.
Locate the RJ-45 connectors. The locations of the USB connectors are shown in Chapter 3. Step 2: Align the connectors. Align the RJ-45 connector on the LAN cable with one of the RJ-45 connectors on the NANO-HM651. See F igure 4-17. Figure 4-17: LAN Connection Step 3: Insert the LAN cable RJ-45 connector.
Figure 4-18: USB Connector 4.9.4 VGA Monitor Connection The NANO-HM651 has a single female DB-15 connector on the external peripheral interface panel. The DB-15 connector is connected to a CRT or VGA monitor. To connect a monitor to the NANO-HM651, please follow the instructions below.
Step 0: 4.10 Software Installation All the drivers for the NANO-HM651 are on the CD that came with the system. To install the drivers, please follow the steps below. Step 1: Insert the CD into a CD drive connected to the system.
NANO-HM651 EPIC SBC Figure 4-20: Introduction Screen Step 3: Click NANO-HM651. Step 4: A new screen with a list of available drivers appears (Figure 4-21). Figure 4-21: Available Drivers Step 5: Install all of the necessary drivers in this menu.
NANO-HM651 EPIC SBC 5.1 Introduction The BIOS is programmed onto the BIOS chip. The BIOS setup program allows changes to certain system settings. This chapter outlines the options that can be changed. 5.1.1 Starting Setup The AMI BIOS is activated when the computer is turned on. The setup program can be activated in one of two ways.
NANO-HM651 EPIC SBC Function F4 key Save all the CMOS changes Esc key Main Menu – Quit and not save changes into CMOS Status Page Setup Menu and Option Page Setup Menu -- Exit current page and return to Main Menu Table 5-1: BIOS Navigation Keys 5.1.3 Getting Help...
NANO-HM651 EPIC SBC 5.2 Main The Main BIOS menu (BIOS Menu 1) appears when the BIOS Setup program is entered. The Main menu gives an overview of the basic system information. Aptio Setup Utility – Copyright (C) 2011 American Megatrends, Inc.
NANO-HM651 EPIC SBC System Time [xx:xx:xx] Use the System Time option to set the system time. Manually enter the hours, minutes and seconds. 5.3 Advanced Use the Advanced menu (BIOS Menu 2) to configure the CPU and peripheral devices through the following sub-menus:...
NANO-HM651 EPIC SBC Aptio Setup Utility – Copyright (C) 2010 American Megatrends, Inc. Advanced ACPI Settings Select the highest ACPI sleep state the system ACPI Sleep State [S1 (CPU Stop Clock)] will enter when the SUSPEND button is pressed. ---------------------- : Select Screen ↑...
NANO-HM651 EPIC SBC Aptio Setup Utility – Copyright (C) 2011 American Megatrends, Inc. Advanced TPM Configuration Enables or Disables TPM TPM SUPPORT [Disable] support. O.S. will not show TPM. Reset of Current TPM Status Information platform is required. TPM SUPPORT OFF...
NANO-HM651 EPIC SBC Aptio Setup Utility – Copyright (C) 2011 American Megatrends, Inc. Advanced CPU Configuration Socket specific CPU Information Intel(R) Celeron(R) CPU 847E @ 1.10GHz Processor Stepping 206a7 Microcode Revision ---------------------- Max Processor Speed 1100 MHz Min Processor Speed...
NANO-HM651 EPIC SBC Enabled Enables Intel Virtualization Technology. 5.3.4 SATA Configuration Use the SATA Configuration menu (BIOS Menu 6) to change and/or set the configuration of the SATA devices installed in the system. Aptio Setup Utility – Copyright (C) 2011 American Megatrends, Inc.
NANO-HM651 EPIC SBC 5.3.5 USB Configuration Use the USB Configuration menu (BIOS Menu 7) to read USB configuration information and configure the USB settings. Aptio Setup Utility – Copyright (C) 2011 American Megatrends, Inc. Advanced USB Configuration USB Support Parameters...
NANO-HM651 EPIC SBC 5.3.6 Super IO Configuration Use the Super IO Configuration menu (BIOS Menu 8) to set or change the configurations for the FDD controllers, parallel ports and serial ports. Aptio Setup Utility – Copyright (C) 2011 American Megatrends, Inc.
Page 87
NANO-HM651 EPIC SBC 5.3.6.1.1 Serial Port 1 Configuration Serial Port [Enabled] Use the Serial Port option to enable or disable the serial port. Disabled Disable the serial port Enable the serial port Enabled EFAULT Change Settings [Auto] Use the Change Settings option to change the serial port IO port address and interrupt address.
Page 88
NANO-HM651 EPIC SBC 5.3.6.1.2 Serial Port 2 Configuration Serial Port [Enabled] Use the Serial Port option to enable or disable the serial port. Disabled Disable the serial port Enable the serial port Enabled EFAULT Change Settings [Auto] Use the Change Settings option to change the serial port IO port address and interrupt address.
Page 89
NANO-HM651 EPIC SBC 5.3.6.1.3 Serial Port 3 Configuration Serial Port [Enabled] Use the Serial Port option to enable or disable the serial port. Disabled Disable the serial port Enable the serial port Enabled EFAULT Change Settings [Auto] Use the Change Settings option to change the serial port IO port address and interrupt address.
NANO-HM651 EPIC SBC IO=2F0h; Serial Port I/O port address is 2F0h and the interrupt IRQ=3, address is IRQ3, 4, 5, 6, 7, 10, 11, 12 5, 6, 7, 10, 11, 12 Serial Port I/O port address is 2E0h and the interrupt IO=2E0h;...
NANO-HM651 EPIC SBC Aptio Setup Utility – Copyright (C) 2011 American Megatrends, Inc. Advanced PC Health Status Smart FAN Configuration CPU temperature :+42 C SYS temperature :+44 C CPU Fan Speed :N/A SYS Fan Speed :N/A VCC_CORE :+0.976 V +5VS :+5.171 V...
NANO-HM651 EPIC SBC 5.3.7.1 Smart Fan Mode Configuration Use the Smart Fan Mode Configuration submenu (BIOS Menu 11) to configure fan temperature and speed settings. Aptio Setup Utility – Copyright (C) 2011 American Megatrends, Inc. Advanced Smart Fan Mode Configuration...
NANO-HM651 EPIC SBC Temperature n Use the + or – key to change the fan Temperature n value. Enter a decimal number between 0 and 100. Duty Cycle n Use the + or – key to change the fan Duty Cycle n value. Enter a decimal number between 0 and 100.
NANO-HM651 EPIC SBC 5.3.9 Sandybridge DTS Configuration Use the Sandybridge DTS Configuration menu (BIOS Menu 13) to configure CPU DTS. BIOS SETUP UTILITY Advanced Disabled: ACPI thermal Sandybridge DTS Configuration management uses EC ⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯ reported temperature values. CPU DTS [Disabled]...
NANO-HM651 EPIC SBC 5.4 Chipset Use the Chipset menu (BIOS Menu 14) to access the Northbridge, Southbridge, Integrated Graphics, and ME Subsystem configuration menus. WARNING! Setting the wrong values for the Chipset BIOS selections in the Chipset BIOS menu may cause the system to malfunction.
NANO-HM651 EPIC SBC 5.4.1 NorthBridge Configuration Use the NorthBridge Configuration menu (BIOS Menu 15) to configure the Northbridge chipset. Aptio Setup Utility – Copyright (C) 2011 American Megatrends, Inc. Chipset NorthBridge Configuration Check to enable VT-d function on MCH. Memory Information...
NANO-HM651 EPIC SBC 5.4.1.1 Graphics Configuration Use the Graphics Configuration menu to configure the video device connected to the system. Aptio Setup Utility – Copyright (C) 2011 American Megatrends, Inc. Chipset Graphics Configuration Select DVMT 5.0 DVMT Pre-Allocated [64M] Pre-Allocated (Fixed)
Page 99
NANO-HM651 EPIC SBC DVMT Total Gfx Mem [MAX] Use the DVMT Total Gfx Mem option to specify the total amount of memory that can be allocated as graphics memory. Configuration options are listed below. 128M 256M EFAULT Boot Display Device Use the Boot Display Device option to select the display device used by the system when it boots.
NANO-HM651 EPIC SBC 1366x768 (24bit) 1440x900 (48bit) 1600x900 (48bit) 1600x1200 (48bit) 1680x1050 (48bit) 1920x1080 (48bit) 1920x1200 (48bit) 5.4.2 Southbridge Configuration Use the Southbridge Configuration menu (BIOS Menu 17) to configure the Southbridge chipset. Aptio Setup Utility – Copyright (C) 2011 American Megatrends, Inc.
Page 101
NANO-HM651 EPIC SBC Enabled The onboard High Definition Audio controller is detected EFAULT automatically and enabled Power Saving Function [Disabled] Use the Power Saving Function option to enable or disable the power saving function. The power saving function is disabled...
NANO-HM651 EPIC SBC 5.5 Boot Use the Boot menu (BIOS Menu 18) to configure system boot options. Aptio Setup Utility – Copyright (C) 2011 American Megatrends, Inc. Main Advanced Chipset Boot Security Save & Exit Boot Configuration Select the keyboard...
Page 103
NANO-HM651 EPIC SBC Quiet Boot [Enabled] Use the Quiet Boot BIOS option to select the screen display when the system boots. Normal POST messages displayed Disabled Enabled OEM Logo displayed instead of POST messages EFAULT Launch PXE OpROM [Disabled] Use the Launch PXE OpROM option to enable or disable boot option for legacy network devices.
NANO-HM651 EPIC SBC 5.6 Security Use the Security menu (BIOS Menu 19) to set system and user passwords. Aptio Setup Utility – Copyright (C) 2011 American Megatrends, Inc. Main Advanced Chipset Boot Security Save & Exit Password Description Set Setup Administrator Password If ONLY the Administrator’s password is set,...
NANO-HM651 EPIC SBC 5.7 Exit Use the Exit menu (BIOS Menu 20) to load default BIOS values, optimal failsafe values and to save configuration changes. Aptio Setup Utility – Copyright (C) 2011 American Megatrends, Inc. Main Advanced Chipset Boot Security Save &...
Page 106
NANO-HM651 EPIC SBC Save as User Defaults Use the Save as User Defaults option to save the changes done so far as user defaults. Restore User Defaults Use the Restore User Defaults option to restore the user defaults to all the setup options.
Page 108
NANO-HM651 EPIC SBC Below is a list of BIOS configuration options in the BIOS chapter. System Overview .........................65 System Date [xx/xx/xx] ......................65 System Time [xx:xx:xx] .......................66 ACPI Sleep State [S1 (CPU Stop Clock)] ................67 TPM Support [Disable] ......................68 ...
Page 109
NANO-HM651 EPIC SBC Restore on AC Power Loss [Last State] ................87 Bootup NumLock State [On]....................88 Quiet Boot [Enabled] ......................89 Launch PXE OpROM [Disabled] ..................89 Option ROM Messages [Keep Current] ................89 Administrator Password .....................90 ...
NANO-HM651 EPIC SBC B.1 One Key Recovery Introduction The IEI one key recovery is an easy-to-use front end for the Norton Ghost system backup and recovery tool. This tool provides quick and easy shortcuts for creating a backup and reverting to that backup or reverting to the factory default settings.
NANO-HM651 EPIC SBC After completing the five initial setup procedures as described above, users can access the recovery tool by pressing <F3> while booting up the system. The detailed information of each function is described in Section B.5. NOTE: The initial setup procedures for Linux system are described in Section B.3.
NANO-HM651 EPIC SBC partitions. Please take the following table as a reference when calculating the size of the partition. OS Image after Ghost Compression Ratio Windows® 7 7 GB 5 GB Windows® XPE 776 MB 560 MB Windows® CE 6.0...
NANO-HM651 EPIC SBC The detailed descriptions are described in the following sections. NOTE: The setup procedures described below are for Microsoft Windows operating system users. For Linux, most of the setup procedures are the same except for several steps described in Section B.3.
NANO-HM651 EPIC SBC Step 2: Boot the system from recovery CD. When prompted, press any key to boot from the recovery CD. It will take a while to launch the recovery tool. Please be patient! Figure B-2: Launching the Recovery Tool Step 3: The recovery tool setup menu is shown as below.
NANO-HM651 EPIC SBC Figure B-4: Command Prompt Step 5: The command prompt window appears. Type the following commands (marked in red) to create two partitions. One is for the OS installation; the other is for saving recovery files and images which will be an invisible partition.
NANO-HM651 EPIC SBC NOTE: Use the following commands to check if the partitions were created successfully. Step 6: Press any key to exit the recovery tool and automatically reboot the system. Please continue to the following procedure: Build the Recovery Partition.S t e p 0 :...
NANO-HM651 EPIC SBC B.2.4 Building the Recovery Partition Step 1: Put the recover CD in the optical drive. Step 2: Start the system. Step 3: Boot the system from the recovery CD. When prompted, press any key to boot from the recovery CD. It will take a while to launch the recovery tool. Please...
NANO-HM651 EPIC SBC Step 5: The Symantec Ghost window appears and starts configuring the system to build a recovery partition. In this process the partition created for recovery files in Section B.2.2 is hidden and the recovery tool is saved in this partition.
NANO-HM651 EPIC SBC B.2.5 Create Factory Default Image NOTE: Before creating the factory default image, please configure the system to a factory default environment, including driver and application installations. To create a factory default image, please follow the steps below.
NANO-HM651 EPIC SBC Figure B-12: About Symantec Ghost Window Step 4: Use mouse to navigate to the option shown below (Figure B-13). Figure B-13: Symantec Ghost Path Step 5: Select the local source drive (Drive 1) as shown in Figure B-14. Then click OK.
NANO-HM651 EPIC SBC Figure B-14: Select a Local Source Drive Step 6: Select a source partition (Part 1) from basic drive as shown in Figure B-15. Then click OK. Figure B-15: Select a Source Partition from Basic Drive Step 7: Select 1.2: [Recovery] NTFS drive and enter a file name called...
NANO-HM651 EPIC SBC Figure B-16: File Name to Copy Image to Step 8: When the Compress Image screen in Figure B-17 prompts, click High to make the image file smaller. Figure B-17: Compress Image Page 111...
NANO-HM651 EPIC SBC Step 12: The recovery tool main menu window is shown as below. Press any key to reboot the system. S t e p 0 : Figure B-21: Press Any Key to Continue B.3 Auto Recovery Setup Procedure...
NANO-HM651 EPIC SBC Step 1: Follow the steps described in Section B.2.1 ~ Section B.2.3 to setup BIOS, create partitions and install operating system. Step 2: Install the auto recovery utility into the system by double clicking the Utility/AUTORECOVERY-SETUP.exe in the One Key Recovery CD. This utility MUST be installed in the system, otherwise, the system will automatically restore from the factory default image every ten (10) minutes.
NANO-HM651 EPIC SBC Step 4: Reboot the system from the recovery CD. When prompted, press any key to boot from the recovery CD. It will take a while to launch the recovery tool. Please be patient! Figure B-24: Launching the Recovery Tool Step 5: When the recovery tool setup menu appears, press <4>...
NANO-HM651 EPIC SBC Figure B-26: Building the Auto Recovery Partition Step 7: After completing the system configuration, the following message prompts to confirm whether to create a factory default image. Type Y to have the system create a factory default image automatically. Type N within 6 seconds to skip this process (The default option is YES).
NANO-HM651 EPIC SBC Step 8: The Symantec Ghost starts to create the factory default image (Figure B-28). Figure B-28: Image Creation Complete Step 9: After completing the system configuration, press any key in the following window to restart the system.
NANO-HM651 EPIC SBC Partition 1: / Partition 2: SWAP NOTE: Please reserve enough space for partition 3 for saving recovery images. Figure B-30: Partitions for Linux Step 3: Create a recovery partition. Insert the recovery CD into the optical disk drive.
NANO-HM651 EPIC SBC recovery partition. After completing the system configuration, press any key to reboot the system. Eject the recovery CD. Figure B-31: Manual Recovery Environment for Linux Step 5: Access the recovery tool main menu by modifying the “menu.lst”. To first access the recovery tool main menu, the menu.lst must be modified.
NANO-HM651 EPIC SBC Step 7: The recovery tool menu appears. (Figure B-33) Figure B-33: Recovery Tool Menu Step 8: Create a factory default image. Follow Step 2 Step 12 described in Section B.2.5 to create a factory default image. S t e p 0 : B.5 Recovery Tool Functions...
NANO-HM651 EPIC SBC Figure B-34: Recovery Tool Main Menu The recovery tool has several functions including: 1. Factory Restore: Restore the factory default image (iei.GHO) created in Section B.2.5. 2. Backup system: Create a system backup image (iei_user.GHO) which will be saved in the hidden partition.
NANO-HM651 EPIC SBC B.5.1 Factory Restore To restore the factory default image, please follow the steps below. Step 1: Type <1> and press <Enter> in the main menu. Step 2: The Symantec Ghost window appears and starts to restore the factory default. A factory default image called iei.GHO is created in the hidden Recovery partition.
NANO-HM651 EPIC SBC B.5.2 Backup System To backup the system, please follow the steps below. Step 1: Type <2> and press <Enter> in the main menu. Step 2: The Symantec Ghost window appears and starts to backup the system. A backup image called iei_user.GHO is created in the hidden Recovery partition.
NANO-HM651 EPIC SBC B.5.3 Restore Your Last Backup To restore the last system backup, please follow the steps below. Step 1: Type <3> and press <Enter> in the main menu. Step 2: The Symantec Ghost window appears and starts to restore the last backup image (iei_user.GHO).
NANO-HM651 EPIC SBC B.5.4 Manual To restore the last system backup, please follow the steps below. Step 1: Type <4> and press <Enter> in the main menu. Step 2: The Symantec Ghost window appears. Use the Ghost program to backup or recover the system manually.
NANO-HM651 EPIC SBC B.6 Restore Systems from a Linux Server through LAN The One Key Recovery allows a client system to automatically restore to a factory default image saved in a Linux system (the server) through LAN connectivity after encountering a Blue Screen of Death (BSoD) or a hang for around 10 minutes.
NANO-HM651 EPIC SBC B.6.1 Configure DHCP Server Settings Step 1: Install the DHCP #yum install dhcp (CentOS, commands marked in red) #apt-get install dhcp3-server (Debian, commands marked in blue) Step 2: Confirm the operating system default settings: dhcpd.conf. CentOS Use the following command to show the DHCP server sample location: #vi /etc/dhcpd.conf...
NANO-HM651 EPIC SBC filename “pxelinux.0”; B.6.2 Configure TFTP Settings Step 1: Install the tftp, httpd and syslinux. #yum install tftp-server httpd syslinux (CentOS) #apt-get install tftpd-hpa xinetd syslinux (Debian) Step 2: Enable the TFTP server by editing the “/etc/xinetd.d/tftp” file and make it use the remap file.
NANO-HM651 EPIC SBC Debian Replace the TFTP settings from “inetd” to “xinetd” and annotate the “inetd” by adding “#”. #vi /etc/inetd.conf Modify: #tftp dgram udp wait root /usr/sbin..(as shown below) #vi /etc/xinetd.d/tftp B.6.3 Configure One Key Recovery Server Settings Step 1: Copy the Utility/RECOVERYR10.TAR.BZ2 package from the One Key...
NANO-HM651 EPIC SBC Figure B-42: Disable Automatically Restart Step 2: Configure the following BIOS options of the client system. Advanced → iEi Feature → Auto Recovery Function → Enabled Advanced → iEi Feature → Recover from PXE → Enabled Boot → Launch PXE OpROM → Enabled...
Page 148
NANO-HM651 EPIC SBC MUST be installed in the system, otherwise, the system will automatically restore from the factory default image every ten (10) minutes. Step 6: Restart the client system from LAN. If the system encounters a Blue Screen of Death (BSoD) or a hang for around 10 minutes, it will automatically restore from the factory default image.
NANO-HM651 EPIC SBC NOTE: A firewall or a SELinux is not in use in the whole setup process described above. If there is a firewall or a SELinux protecting the system, modify the configuration information to accommodate them. B.7 Other Information B.7.1 Using AHCI Mode or ALi M5283 / VIA VT6421A Controller...
Page 150
NANO-HM651 EPIC SBC Step 5: When the following window appears, press <S> to select “Specify Additional Device”. Page 136...
NANO-HM651 EPIC SBC Step 6: In the following window, select a SATA controller mode used in the system. Then press <Enter>. The user can now start using the SATA HDD. Step 7: After pressing <Enter>, the system will get into the recovery tool setup menu.
Page 153
NANO-HM651 EPIC SBC AC ’97 Audio Codec 97 (AC’97) refers to a codec standard developed by Intel® in 1997. ACPI Advanced Configuration and Power Interface (ACPI) is an OS-directed configuration, power management, and thermal management interface. AHCI Advanced Host Controller Interface (AHCI) is a SATA Host controller register-level interface.
Page 154
NANO-HM651 EPIC SBC Direct Memory Access (DMA) enables some peripheral devices to bypass the system processor and communicate directly with the system memory. DIMM Dual Inline Memory Modules are a type of RAM that offer a 64-bit data bus and have separate electrical contacts on each side of the module.
Page 155
NANO-HM651 EPIC SBC Liquid crystal display (LCD) is a flat, low-power display device that consists of two polarizing plates with a liquid crystal panel in between. LVDS Low-voltage differential signaling (LVDS) is a dual-wire, high-speed differential electrical signaling system commonly used to connect LCD displays to a computer.
NANO-HM651 EPIC SBC D.1 Introduction The DIO connector on the NANO-HM651 is interfaced to GPIO ports on the Super I/O chipset. The DIO has both 4-bit digital inputs and 4-bit digital outputs. The digital inputs and digital outputs are generally control signals that control the on/off circuit of external devices or TTL devices.
NANO-HM651 EPIC SBC D.3 Assembly Language Samples D.3.1 Enable the DIO Input Function The BIOS interrupt call INT 15H controls the digital I/O. An assembly program to enable digital I/O input functions is listed below. Sets the digital port as input...
Page 160
NANO-HM651 EPIC SBC NOTE: The following discussion applies to DOS. Contact IEI support or visit the IEI website for drivers for other operating systems. The Watchdog Timer is a hardware-based timer that attempts to restart the system when it stops working. The system may stop working because of external EMI or software bugs.
Page 161
NANO-HM651 EPIC SBC NOTE: The Watchdog Timer is activated through software. The software application that activates the Watchdog Timer must also deactivate it when closed. If the Watchdog Timer is not deactivated, the system will automatically restart after the Timer has finished its countdown.
NANO-HM651 EPIC SBC F.1 Hazardous Materials Disclosure Table for IPB Products Certified as RoHS Compliant Under 2002/95/EC Without Mercury The details provided in this appendix are to ensure that the product is compliant with the Peoples Republic of China (China) RoHS standards. The table below acknowledges the presences of small quantities of certain materials in the product, and is applicable to China RoHS only.
Page 164
NANO-HM651 EPIC SBC Part Name Toxic or Hazardous Substances and Elements Lead Mercury Cadmium Hexavalent Polybrominated Polybrominated Biphenyls Diphenyl (Pb) (Hg) (Cd) Chromium (CR(VI)) (PBB) Ethers (PBDE) Housing Display Printed Circuit Board Metal Fasteners Cable Assembly Fan Assembly Power Supply...