Table of Contents
Advertisement
Quick Links
AM
MIS49
9587
Ge
etting st
tarted w
49
9587 Eva
aluation
Prep
pared by: Ind
ustrial ASSP
In
ntroductio
n
Co
ongratulations, h
here is the AMI
mode
em demonstrati
ion kit from ON
prese
ent document w
will help you to
U
npack you
ur materia
Th
he evaluation ki
t contains the fo
•
•
2 AMIS-4
49587 evaluatio
plugged on D
Daughter Board
•
•
2 USB ser
rial cables
•
•
This manu
ual
Ma
ains connection
HW
W require
ements
Th
he material nec
essary to run a
given
n hereunder:
•
•
1 PC runn
ning Windows
free.
•
•
2 AMIS-4
49587 evaluatio
•
•
2 USB cab
bles
•
•
2 mains c
cables. To conn
connector.
(not included)
connect to L
Line and Neutra
SW
W require
ments
Be
efore starting th
he PLC UI, mak
JRE
6.13 or higher
r is installed o
'java
a.com/getjava'.
On MS Windo
be in
nstalled automat
tically.
Th
he User Interfac
ce Software and
be do
ownloaded from
m:.
http:/
//www.onsemi.
com/PowerSolu
4958
7
© S
Semiconductor Comp
ponents Industries, LL
Au
ugust 31, 2011
– Rev. 008
with the
e AMIS-
n kit
- ON Semico
onductor
IS-49587 powe
er line carrier
N Semiconducto
or, Inc.. The
get the kit work
king quickly.
al
following eleme
ents:
n boards (Moth
her Board and
d)
Mothter Boar
d
Da
aughter Board
USB conn
a communicatio
on with the kit
XP or higher w
with 2 USB po
n boards
nect to the Mo
other Board m
. Please take
care to correc
al.
ke sure the Java
a Runtime Eng
or download an
nd install it fro
ows based platf
forms the JRE w
d most recent do
ocumentation ca
utions/product.
do?id=AMIS-
LC, 2011
-
The USB po
co
onverter. A ded
do
ownload it from
http://www.ftd
Setting u
Once you get t
Step 1:
Connect the bo
AMIS-49587
RESET
USB conn
Step 2:
Connect the PL
nection
t is
orts
ain
ctly
Mains connec
Step 3:
Power the PLC
ine
om
will
IM
MPORTANT
de
emonstration
an
Di
isconnect the b
of
f it. Be sure
manipulate it.
m
1
http://onsem
mi.com
ort communica
ates with a F
dicated USB d
driver is neede
m the FTDI web
bsite:
dichip.com/FTD
Drivers.htm.
p the hard
dware
the above listed
d elements, you
oth PLC MODE
EM's to the US
nection
LC MODEM m
mains plug to the
ction
C MODEM.
REMARK: 2
230V mains a
board. Keep
p the board
board from th
he mains befor
that only tra
ained people
Publication
FTDI serial U
UART
ed for this. Yo
ou can
need to:
B ports of the P
PC.
e mains.
are present on
n the
in a safe
area.
re any manipul
lation
are authorize
ed to
Order Number:
:
AMIS-49587
Advertisement
Table of Contents
Related Manuals for ON Semiconductor AMIS-49587
Summary of Contents for ON Semiconductor AMIS-49587
- Page 1 B ports of the P • • 2 USB ser rial cables • • This manu Mothter Boar ains connection AMIS-49587 RESET USB conn nection Step 2: aughter Board Connect the PL LC MODEM m mains plug to the e mains.
- Page 2 If it is not, the installer will start downloading it from the Sun website and install it. For non MS Windows based platforms see SW requirements. When the required Java Runtime Engine is installed, installation of the ON Semiconductor PLC Modem application will proceed. 1.4.7 AMIS49587 GUI application note.pdf plcui.chm PlcUi.jar...
- Page 3 AMIS-49587 Enter the frame length. The maximum is 247 bytes, the minimum is 13 bytes. Chat Application Enter the number of times the data needs to be transmitted Enter the destination address When the Chat application is chosen: Check the ‘Wait for looped data’ checkbox to make sure the Type the address of the MODEM to whom you would like transmitter doesn’t send a new frame before receiving the...
- Page 4 AMIS-49587 File Transfer Application 0 Never Repeater or Mode=Master, 1 Always Repeater, 2 Not Repeater (accept frame ISACall), The file transfer application sends a file from the transmitter to 3 Repeater (accept frame ISACall) the receiver. Before initiating transmit, the addressed node should </Note>...
- Page 5 MIS-495 Sending an a alarm When a slave encounters an n alarm conditi ion, managed b by the pplication layer r on the extern nal controller, the application n may ecide to send o out an alarm no otification on t the power line.
- Page 6 AMIS-49587 All MODEM parameters are listed in the xml configuration file The embedded SW in our PLC silicon issues the error message as follows: LM_TU1, or NEG at the MAC level when: Slave MODEM is set to 'never repeater' <parameter string representation>...
- Page 7 AMIS-49587 Go back to the status pane on the slave node and witness that the repeater status has changed from no repeater to repeater because the server did not receive any ISA call pattern from any other MODEM. Note that the MODEM may respond negative (62 00) many times because its physical layer is busy.
- Page 8 Emai l: orderlit@onsemi.c Japan Cu ustomer Focus Cent Sales R Representative Phone: 81 1-3-5773-3850 Publication Order Number: © S Semiconductor Comp ponents Industries, LL LC, 2011 ugust 31, 2011 – Rev. 008 AMIS-49587...
Need help?
Do you have a question about the AMIS-49587 and is the answer not in the manual?
Questions and answers