Download Print this page

Before Operation - Sanyo DC-D27 Instruction Manual

Hide thumbs

Advertisement

BEFORE OPERATION
i
Turning the power on and off
Press the POWER button. The displays light and the STANDBY indicator
goes out. (After connecting the mains lead, when you press the POWER
button for the first time, the volume reset feature automatically
reduces the
volume level.)
To turn off the power, press the POWER button again. The STANDBY
indicator lights.
When the mains lead is connected to the AC outlet, the STANDBY
indicator lights and the unit will respond to commands from the remote
control.
Smart start function
If the following buttons are pressed when the power is turned off, the
unit turns on automatically
and the selected function is set.
CD player section
PLAY/PAUSE,
DISC 1, DISC 2, DISC 3,
OPEN/CLOSE
Tuner section
BAND
Cassette section
D , Q DECK A ONLY
Graphic display
Below indication
appears on the display for a few seconds when corre-
sponding operation button is pressed.
F,<,
-F,
<<,
II, m, O, O, A,B,
1,2,.....16
Selecting the function
Press the FUNCTION button to select the desired function. The selected
function indicator lights in red.
The function is automatically
selected when CD play or tape playback is
started, or when the BAND button has been pressed (except during
recording or tape dubbing).
When the function selection is changed, CD play or tape playback is
automatically
stopped.
Adjusting the volume
Turn the VOLUME control, or press the "+" or "-" VOLUME button on the
remote control.
Adjusting the left/right speaker balance
Use the BALANCE
control to adjust the lefVright speaker balance.
Adjusting
the sound quality
Turn the SPECTRUM
CONTROL to LOW to increase the Iowfrequencies.
Turn the control to HIGH to increase the high frequencies.
To reduce the volume temporarily
(muting)
Press the MUTE button on the remote control. "MUTE" blinks on the
display.
To restore the previous volume setting, press the MUTE button again.
"MUTE" disappears.
Bass expander system
Press the BASSXPANDER
button to enhance the bass sound. "BASS"
appears on the display.
The initial setting of this function is ON.
Selecting
the sound mode
Press the SOUND PRESET button to select the sound mode matching the
music to be listened to.
POP: Pops, etc.
ROCK:
Rock music, etc.
.10-
+10-=
.==
=
=
==-
=
0-
=-
o—
====
-
=
-lo -
.lo -
.%
150 400
lk
24k
%
15k-
60
150 4CUI lk
24k
6k
15k-
CLASSIC:
Classical music, etc.
JAZZ:
Jazz, etc.
.10-.
.10-
.=
-=
=
0.======
-
0-
===
==-
-10-
-10-
60
150 400
Ik
24k
%
15k-
EO 150 4W
lk
24k
6k
1*-
Spectrum
analyzer
Indicates the input level and peak value of each sound range.
Demonstration
mode
If the DISPLAY button is Dressed, the disdav
enters the demonstration
mode. The following dispiay modes will sequentially
appear.
AMP—CD
—TUNER—TAPE
—AMP—
.
To cancel this mode, press the DISPLAY button again.
WHAT TO DO IF ...
If the operation
of the unit or display is not normal or when all the
memory contents are to be cleared, disconnect the mains lead from the
AC outlet, then press the RESET button (rear of the unit) for20 seconds
or more.
RESET
%
r-
-5-

Advertisement

loading

  Also See for Sanyo DC-D27

  Related Manuals for Sanyo DC-D27