Sanyo DC-D27 Instruction Manual page 9

Hide thumbs Also See for DC-D27:
Table of Contents

Advertisement

Disc check
Press the DISC CHECK button to play the first 10 seconds of the first track
of each disc. " D" and "dlSC CH" appear and the disc number blinks on
the display.
Press the F-/
FFi SKlP/SEARCH
button toskipto
the next disc.
Each time the button is pressed, the player will skip to the next disc.
Press the DISC CHECK button again to return to normal play.
PROGRAMMED
PLAY
Up to 24 selections, from up to 3 discs, can be programmed
for play in any
order.
To begin the programming
procedure, select "CD function first.
The discs or tracks must be programmed
in the stop mode.
-
The same disc or track can be programmed
more than once.
Load discs that you want to programme
before starting programmed
play.
Follow the example below to programme tracks 2 and 6 on DISC 1 and all
tracks on DISC 3. In this example, each disc has 9 tracks and DISC 3 is
in playing position.
1.
Press the MEMORY button
C-5
,,/
mm
m
2.
Select disc 1 by pressing the DISC 1 button.
The DISC SELECT button on the remote control can also be used.
,,,
PKx
EB
3.
Select track 2 by pressing the
P/ bbl
SKIP/SEARCH
button.
The number buttons on the remote control can also be used.
Pr.
1
\l/
mm
BI
4.
Press the MEMORY button.
m'
•E
5.
Select track 6 by pressing the
F/
Pl SKIP/SEARCH
button
Pr.
2
&'
E!
6.
Press the MEMORY button.
8.
Press the MEMORY button.
9.
Press the PLAY/PAUSE
button to start play.
When
all programmed
selections
have played,
the player stops
automatically.
"O 0.00 appears on the display.
The programme
contents are retained in memory.
Any attempt to programme
more than 24 selections
will result in
"FULL" being displayed and discontinuation
of the programming.
-
The programme
is cleared in the following cases:
-
When the STOP button is pressed in the stop mode
When the OPEN/CLOSE
button is pressed
Checking
the programme
Each time the MEMORY
button is pressed in the stop mode, the pro-
grammed details sequentially
appear on the display.
Changing
a programme
To add a new selection
to a programme:
1.
In the stop mode, press the MEMORY button repeatedly until"- - --
.- -" is displayed.
2.
Select a disc and track number as explained above.
3.
Press the MEMORY button.
To change
a selection:
1.
In the stop mode, press the MEMORY
button repeatedly
until the
selection to be replaced is displayed.
2.
Select a disc and track number as explained above.
3.
Press the MEMORY button.
Note:
Programmed
details cannot be partially deleted or inserted.
WHAT TO DO IF ...
If "ME dlSC
appears.
1.
Press the POWER button to turn the power off.
2.
Press the POWER button to turn the power on.
If the operation
of the unit or display is not normal, even though the
appropriate
buttons have been pressed.
1.
Disconnect the mains lead.
2.
Press the RESET button (rear of the unit) for 20 seconds or more.
3.
Connect the mains lead.
4.
Press the POWER button to turn the power on.
5.
Press the desired function button.
Note:
If the unit does not operate correctly, or "ME dlSC
appears again,
please contact your nearest SANYO Authorized Service Centre.
mm:
EBl
7.
Select disc 3 by pressing the DISC 3 button.
IEE
-7-

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the DC-D27 and is the answer not in the manual?

Subscribe to Our Youtube Channel

Table of Contents