Vertiv Liebert ITA2 Installation Manual
Vertiv Liebert ITA2 Installation Manual

Vertiv Liebert ITA2 Installation Manual

Battery cabinet 8-10kva, 60hz, 208/220v
Hide thumbs Also See for Liebert ITA2:

Advertisement

Quick Links

Liebert
ITA2
Battery Cabinet 8-10kVA, 60Hz,
®
208/220V
Installation Manual

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Liebert ITA2 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Vertiv Liebert ITA2

  • Page 1 Liebert ITA2 Battery Cabinet 8-10kVA, 60Hz, ® ™ 208/220V Installation Manual...
  • Page 2 Services offers a complete range of startup services, repair services, preventive maintenance plans and service contracts. For repair or maintenance service outside the 48 contiguous United States, contact Vertiv Services, if available in your area. For Vertiv Services to assist you promptly, have the following information available:...
  • Page 3: Table Of Contents

    Figure 10 Cables between Liebert ITA2 and battery cabinets ....... .
  • Page 4 Vertiv ™ ® | Liebert ITA2 208/220V Battery Cabinet Installation Manual | Rev. 0 | 01/18 |...
  • Page 5: Important Safety Instructions

    Special safety precautions are required for procedures involving handling, installation and maintenance of the UPS system. Only properly trained and qualified personnel wearing appropriate personal protective equipment should be involved in installing the Liebert ITA2 battery system or preparing the system for installation.
  • Page 6 Operation of this unit in a residential area may cause harmful interference that the user must correct at his own expense. Vertiv | Liebert ®...
  • Page 7: Introduction

    INTRODUCTION The Liebert ITA2 Battery Cabinet (ITA2-BCI0020K03) provides DC input power the Liebert ITA2 UPS. Read this manual carefully before installing or operating the battery system. The battery cabinet may be installed either in a rack or in a tower configuration. A maximum of five battery strings can be connected to a Liebert ITA2 UPS.
  • Page 8: Installation

    INSTALLATION Preparation 2.1.1 Installation Environment The Liebert ITA2 Battery Cabinet must be installed in an environment meeting the following requirements: • Well-ventilated • No direct sunlight on the system • Free from water, heat source and flammable and explosive substances •...
  • Page 9: Mechanical Installation-Tower

    Place the battery cabinets and the UPS on the support bases, as shown in Figure 5. Figure 5 Tower installation Liebert ITA2 UPS 2. Liebert ITA2 Battery Cabinets, 4 3. Support Base Attach the bezel to each battery cabinet, see 2.3 - Attaching and Removing the Bezel. Vertiv | Liebert ®...
  • Page 10: Mechanical Installation-Rack

    Risk of improper transport. Can cause damage to the UPS or battery cabinets. Never attempt to lift or move the Liebert ITA2 or battery cabinets with the rack brackets. The brackets and screws are not designed to be used to lift the units.
  • Page 11: Connecting One Battery Cabinet

    Figure 8 Standard rack installation Liebert ITA2 UPS 2. Battery Cabinets, 4 Connecting One Battery Cabinet Do not reverse the polarity of the battery cables. Before replacing the battery cabinet and connecting the battery cables, ensure the battery breaker on the rear of the battery cabinet is open (Off).
  • Page 12: Installing The Battery Cabinet

    Figure 10, Terminals A of the first string connects to the UPS. Terminal B of the first string will connect to Terminal A of the second string. Figure 10 Cables between Liebert ITA2 and battery cabinets CABLES FOR UPS TO ONE BATTERY STRING CABLES FOR ADDITIONAL BATTERY STRINGS Communication Cable 2.
  • Page 13: Figure 11

    Battery Cabinet 3 13. RJ-45 Communication Cables 14. Communication Port 2 15. Communication Port 1 of Battery Cabinet 1 of Battery Cabinet 1 Vertiv | Liebert ® ™ ITA2 208/220V Battery Cabinet Installation Manual | Rev. 0 | 01/18 |...
  • Page 14: Connecting Additional Battery Cabinets

    Connect the communication cable to the RJ-45 port on the battery cabinet to the UPS as shown in Figure 11 shows two battery strings connected in parallel. To connect the battery cabinets to the Liebert ITA2 UPS, refer to the UPS user manual, SL-00030, which shipped with the UPS and is available at Vertiv’s Web site: www.vertivco.com...
  • Page 15: Specifications

    32.4 x 32.4 x 29.5 ( 822.5 x 823 750) (2 Cabinets per Carton) Weight, Approximate, lb. (kg) Net (One Cabinet) 115 (52.2) Shipping 306.4 (139) (2 Cabinets per Carton) Vertiv | Liebert ® ™ ITA2 208/220V Battery Cabinet Installation Manual | Rev. 0 | 01/18 |...
  • Page 16 Vertiv | Liebert ® ™ ITA2 208/220V Battery Cabinet Installation Manual | Rev. 0 | 01/18 |...
  • Page 17 TECHNICAL SUPPORT / SERVICE Web Site www.vertivco.com Monitoring liebert.monitoring@vertivco.com 800-222-5877 Outside North America: +00800 1155 4499 Three-Phase UPS & Power Systems 800-543-2378 Outside North America: 614-841-6598 LOCATIONS United States 1050 Dearborn Drive P.O. Box 29186 Columbus, OH 43085 Europe Via Leonardo Da Vinci 8 Zona Industriale Tognana 35028 Piove Di Sacco (PD) Italy +39 049 9719 111...
  • Page 18 © 2016 Vertiv Co. All rights reserved. Vertiv and the Vertiv logo are trademarks or registered trademarks of Vertiv Co. All other names and logos referred to are trade names, trademarks or registered trademarks of their respective owners. While every precaution has been taken to ensure accuracy and completeness herein, Vertiv Co. assumes no responsibility, and disclaims all liability, for damages resulting from use of this information or for any errors or omissions. Specifications are subject to change without notice.

Table of Contents