Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for Datalogic BC9030
Summary of Contents for Datalogic BC9030
- Page 1 BC9030 BT Presentation Base Quick Reference Guide...
- Page 2 U.S. and the E.U. The Bluetooth word mark and logos are owned by Blue- tooth SIG, Inc. and any use of such marks by Datalogic Group companies is under license. All other brand and product names may be trademarks of their respective owners.
-
Page 3: Table Of Contents
Table of Contents Using the BC9030 BT Presentation Base ............. 1 Installation ....................... 2 Regulating the Cradle Position .............. 2 Mounting with the Metal Plate ............. 4 System Connections ..................5 Connecting and Disconnecting the Interface Cable ......5 BC9030-BT-BP Configuration ................ 6 Datalogic Aladdin™... -
Page 5: Using The Bc9030 Bt Presentation Base
Using the BC9030 BT Presentation Base The BC9030 BT Presentation Base, when paired with one or more PowerScan™ PM9500 readers, builds a Cordless Reading System for the collection, decod- ing and transmission of bar code data. It can be connected to a Host PC via RS-232, USB, or KBD Wedge, and is suited for single-cradle layouts. -
Page 6: Installation
Installation Installation To set up your BC9030-BT-BP cradle you must: Physically install the cradle. Make all system connections. Configure the BC9030-BT-BP cradle. The cradle package contains the following items: • BC9030 BT Presentation Base • Hex Key • BC9030-BT-BP Quick Reference Guide •... - Page 7 Installation The rubber spacers included in the box can be used to fix the position of the cradle: Quick Reference Guide...
-
Page 8: Mounting With The Metal Plate
Installation Mounting with the Metal Plate Affix the metal plate onto the desired mounting surface using the two center screw holes (see Figure 1 on page Slide the tabs on the back of the cradle onto the metal plate as shown in Figure After aligning the tabs, push up to lock into place. -
Page 9: System Connections
Multi-Interface Connector Connecting and Disconnecting the Interface Cable The BC9030-BT-BP can be connected to a Host by means of a multi-interface cable, which must be simply plugged into the Host connector, visible on the front panel of the cradle. To disconnect the cable, insert a paper clip or other similar object into the hole corresponding to the Host connector on the body of the cradle. -
Page 10: Bc9030-Bt-Bp Configuration
USB Port. The power supply is not required if you connect the interface cable to a PoweredUSB 12V or 24V port. NOTE BC9030-BT-BP Configuration The BC9030-BT-BP configuration can be performed in three ways: by using ™ the Datalogic Aladdin software configuration program, by sending configura- tion strings from the Host PC via the RS-232 or USB-COM interface or by reading configuration bar codes with the PowerScan™... -
Page 11: Serial Configuration
PM9500. Any customized settings that may have been applied to the reader will be lost. CAUTION To change the defaults refer to the PowerScan™ 9500 PRG, or to the Datalogic ™ Aladdin Configuration program, both downloadable from the Datalogic web- site. -
Page 12: Selecting The Interface Type
Selecting the Interface Type Selecting the Interface Type Upon completing the physical connection between the reader and its host, scan the appropriate bar code for your system’s correct interface type. Configuring the Interface Scan the programming bar code which selects the appropriate interface type for the system the reader will be connected to. - Page 13 (can be used for OPOS/UPOS/JavaPOS) USB-OEM USB Keyboard with standard key encoding Select USB Keyboard USB Keyboard with alternate key encoding USB Alternate Keyboard USB Keyboard for Apple computers USB-KBD-APPLE a. Download the correct USB COM driver from www.datalogic.com Quick Reference Guide...
-
Page 14: Keyboard Interface
Selecting the Interface Type Keyboard Interface Use the programming bar codes to select options for USB Keyboard and Wedge Interfaces. KEYBOARD AT, PS/2 25-286, 30-286, 50, 50Z, 60, 70, 80, 90 & 95 w/ Standard Key Encoding Select KBD-AT Keyboard Wedge for IBM AT PS2 with standard key encoding but without external keyboard Select KBD-AT-NK AT, PS/2 25-286, 30-286, 50, 50Z, 60, 70, 80, 90 &... -
Page 15: Scancode Tables
Selecting the Interface Type KEYBOARD (continued) Keyboard Wedge for IBM Terminal 3153 Select KBD-IBM-3153 Keyboard Wedge for IBM Terminals 31xx, 32xx, 34xx, 37xx make only keyboard Select KBD-IBM-M Keyboard Wedge for IBM Terminals 31xx, 32xx, 34xx, 37xx make break keyboard Select KBD-IBM-MB Keyboard Wedge for DIGITAL Terminals VT2xx, VT3xx, VT4xx... -
Page 16: Country Mode
Selecting the Interface Type Country Mode This feature specifies the country/language supported by the keyboard. Only these interfaces support ALL Country Modes: • USB Keyboard (without alternate key encoding) • AT, PS/2 25-286, 30-286, 50, 50Z, 60, 70, 80, 90 & 95 w/Std Key Encoding •... - Page 17 Selecting the Interface Type COUNTRY MODE (continued) Country Mode = Croatia* Country Mode = Czech Republic* Country Mode = Denmark* Country Mode = France $CKBCO13(CR) Country Mode = French Canadian Country Mode = Germany *Supports only the interfaces listed in the Country Mode feature description Quick Reference Guide...
- Page 18 Selecting the Interface Type COUNTRY MODE (continued) Country Mode = Hungary* Country Mode = Italy Country Mode = Japanese 106-key* $CKBCO14(CR) Country Mode = Lithuanian Country Mode = Norway* Country Mode = Poland* Country Mode = Portugal* *Supports only the interfaces listed in the Country Mode feature description BC 9xx0-BT Cradle...
- Page 19 Selecting the Interface Type COUNTRY MODE (continued) Country Mode = Romania* Country Mode = Spain Country Mode = Sweden Country Mode = Slovakia* Country Mode = Switzerland* *Supports only the interfaces listed in the Country Mode feature description Quick Reference Guide...
-
Page 20: Caps Lock State
Selecting the Interface Type Caps Lock State This option specifies the format in which the reader sends character data. This applies to keyboard wedge interfaces. This does not apply when an alter- nate key encoding keyboard is selected. ENTER/EXIT PROGRAMMING MODE Caps Lock State = Caps Lock OFF Caps Lock State = Caps Lock ON Caps Lock State = AUTO Caps Lock Enable... -
Page 21: Numlock
Selecting the Interface Type Numlock This option specifies the setting of the Numbers Lock (Numlock) key while in keyboard wedge interface. This only applies to alternate key encoding inter- faces. It does not apply to USB keyboard. ENTER/EXIT PROGRAMMING MODE Numlock = Numlock key unchanged Numlock = Numlock key toggled Quick Reference Guide... -
Page 22: Technical Features
Technical Features Technical Features ELECTRICAL FEATURES Supply Voltage External Power 10 - 30 VDC Host Power (Powered USB or RS232) Power Consumption External Power max. 10 W (charging) * Host Power max. 10 W (charging) * Ext. Power/Data yellow LED Host Power/Data yellow LED Reader batt. - Page 23 Width 98mm SYSTEM CONFIGURATION Max number of devices per base station * Having a switching regulator inside, the BC9030-BT-BP draws the same power, regardless of the supply voltage. i.e. as the input voltage increases the current drawn decreases Quick Reference Guide...
-
Page 24: Datalogic Limited Factory Warranty
Datalogic service center, with ship- ping charges prepaid. Datalogic shall pay for the return of the product to Customer if the shipment is to a location within the country in which the Datalogic service center is located. -
Page 25: Ergonomic Recommendations
DAMAGES. Risk of Loss Customer shall bear risk of loss or damage for product in transit to Datalogic. Datalogic shall assume risk of loss or damage for product in Datalogic’s possession. In the absence of spe- cific written instructions for the return of product to Customer, Datalogic will select the car- rier, but Datalogic shall not thereby assume any liability in connection with the return shipment. -
Page 26: Support Through The Website
Support Through the Website Support Through the Website Datalogic provides several services as well as technical support through its website. Log on to www.datalogic.com and click on the SUPPORT > Industrial Hand- held Scanners category link. From this page you can select your product... - Page 27 Support Through the Website NOTES Quick Reference Guide...
- Page 28 Support Through the Website NOTES BC 9xx0-BT Cradle...
- Page 29 Support Through the Website NOTES Quick Reference Guide...
- Page 30 Support Through the Website NOTES BC 9xx0-BT Cradle...
- Page 32 ©2013-2017 Datalogic S.p.A. and/or its affiliates. All rights reserved. Datalogic and the Datalogic logo are registered trademarks of Datalogic S.p.A. in many countries, including the U.S.A. and the E.U. Datalogic USA, Inc 959 Terry Street | Eugene, OR 97402 |USA...