Husqvarna Automower 105 Operator's Manual page 23

follows this to and from the charging station. The area
beside the wire which the robotic lawnmower uses is
called the Corridor.
The robotic lawnmower has a default setting for
wide corridors. To further reduce the risk of tracks
forming, it is recommended to select as wide corridor as
Narrow corridor setting is not normally
possible. The
recommended, but in a garden with one or many narrow
passages, a narrow corridor may be the only option. The
Narrow corridor setting increases the risk for tracks
forming along the guide.
3.14.2 Remote start 1
One important function with the guide wire is the
possibility to steer the robotic lawnmower to remote
garden areas when required. This function is very useful
in gardens where, for instance, the front and back are
joined by a narrow passage.
Remote start 1
3.14.2.1 Proportion
With this function activated, (any option other than
Never is selected) the robotic lawnmower will at times
follow the guide wire from the charging station to the
remote area and begin mowing there.
How often the robotic lawnmower must follow the guide
wire from the charging station is selected as a proportion
of the total number of times it leaves the charging
station. At all other times, the robotic lawnmower leaves
the charging station in the standard manner and starts to
mow.
Proportion
Never
Rarely
Medium
Often
Always
• The following five options can be selected;
Never (0%)
-
Rarely (approx. 20%)
-
Medium (approx. 50%)
-
Often (approx. 80%)
-
Always (100%)
-
Select the percentage that corresponds to the size
of the remote area relative to the total working area.
If the remote area is for instance less than half of the
total working area, then
the remote area is for instance half of the total
Medium should be selected. Compare
working area,
136 - 003 -
Medium
Proportion
Distance
Rarely should be selected. If
with the examples in
27 . The default setting is Rarely .
3.14.2.2 Distance
Enter the distance in metres along the guide wire from
the charging station to the remote area where the
robotic lawnmower begins mowing. Tip! Use the
OUT function to determine how far it is to the remote
area. The distance, stated in metres, will be shown in
the robotic lawnmower's display.
3.14.3 Remote start 2
If the working area contains two remote areas, the guide
wire should be installed so that it reaches both areas.
Remote start 1 and Remote start 2 can then be
combined to steer the robotic lawnmower to each area.
Proportion and Distance are carried out
The settings for
Remote start 1 . The default
in the same way as for
Never .
setting is
Take into account that the total figure for
cannot exceed 100%. If one has for instance selected
Often for Remote start 1 , then one can only select Never
or Rarely for Remote start 2 .
3.14.4 Test settings
Test settings menu, it is possible to test how the
In the
Remote start 1 and Remote start 2 work in
settings for
the working area in question.
Test settings
Test OUT Remote start 1
Remote start 2
3.14.4.1 Test OUT
Test OUT function is used to test if the selected
The
Guide width suits the installation in question and to
calculate the distance from the charging station to a
remote area.
Remote start 1 :
To test the settings in
Park the robotic lawnmower in the charging station and
select Test OUT - Remote start 1 . The robotic
lawnmower will then leave the charging station straight
away along the guide wire and begin mowing after the
designated distance.
If there is a passage that the robotic lawnmower cannot
get through, the settings in Guide width ought to be
Wide to Medium . If required, the setting
changed from
Narrow . The Narrow guide width
can also be changed to
setting should only be used if none of the other settings
work for this installation. When the
activated, the robotic lawnmower travels the farthest
distance from the wire allowed by the selected guide
width.
Yard layout examples on page
Test
Proportion
Test IN
Test OUT
Test OUT function is
Installation - 23