First Start-Up And Calibration; Test Docking With The Charging Station; Control Panel - Husqvarna Automower 105 Operator's Manual

See Indicator lamp in the charging station on page 38 if
the lamp does not indicate a solid or flashing green light.

3.9 First start-up and calibration

When the main switch is set to position
time, a start-up sequence in the robotic lawnmower's
menu must be carried out as well as an automatic
calibration of the guide signal.
1. Open the hatch by pressing the STOP button.
2. Set the main switch to position
A start-up sequence begins when the robotic
lawnmower is started for the first time. The following
is requested:
• Language.
• Country
• Date
• Time
• Selection and confirmation of personal PIN code.
All combinations except 0000 are permitted.
MEMO page at the beginning of the
Note: Use the
manual to make a note of the PIN code.
3. Place the robotic lawnmower in the charging station
and press START. The robotic lawnmower will now
begin to calibrate the guide wire.
Press START and close the hatch. The calibration is
performed by the robotic lawnmower backing out of
the charging station and running a calibration
process in front of the charging station. When this is
completed, mowing can begin.

3.10 Test docking with the charging station

Before using the robotic lawnmower, check that the
robotic lawnmower can follow the guide wire all the way
to the charging station and easily docks with the
charging station. Perform the test below.
1. Open the panel hatch by pressing the STOP button.
2. Place the robotic lawnmower close to the point
where the guide wire is connected to the boundary
wire. Place the robotic lawnmower about 2 m from
the guide wire, facing the guide wire.
3. Select HOME mode by pressing the house symbol
OK when the cursor is at Home.
key and pressing
Press START and close the hatch.
4. Check that the robotic lawnmower follows the guide
wire all the way to the charging station and that it
docks with the charging station. The test is approved
only if the robotic lawnmower is able to follow the
guide wire the entire distance to the charging station
20 - Installation
1 for the first
1 .
and docks at the first attempt. If the robotic
lawnmower is unable to dock on the first attempt, it
will automatically try again. The installation is not
approved if the robotic lawnmower needs two or
more attempts to dock with the charging station. In
this case, check that the charging station, the
boundary wire and the guide wire are installed in
accordance with the instructions.
5. The robotic lawnmower will stay in the charging
AUTO or MAN mode is selected. See
station until
Operation selection on page 30 .
The guide system must first be calibrated if the
above test is to provide a satisfactory result. See
First start-up and calibration on page 20 .

3.11 Control panel

3.11.1 Instruction - Control panel
All commands and settings for the robotic lawnmower
are made via the control panel. All functions are
accessed via a number of menus.
The control panel consists of a display and a keypad. All
information is shown on the display and all input is done
using the buttons.
3.11.2 Keypad
The keypad consists of 4 groups of buttons:
• The START button is used to activate the robotic
lawnmower. This is normally the last button to be
pressed before closing the hatch.
• The 3 multi-choice buttons offer various functions,
depending on where in the menu structure you are.
The button function is shown at the bottom of the
display.
• The number keys are used for instance to enter the
PIN code or time settings.
• The operation selection button is symbolised by a
house. When the button has been pressed, the
selected operation mode is shown in the display.
3.11.3 Display
When the STOP button has been pressed and the hatch
is opened, the operation window appears showing the
time, selected operating mode, number of mowing
hours, battery status and timer setting.
• The clock shows the current time.
• Date shows the current day.
136 - 003 -