1. Manuals
  2. Brands
  3. Utopia Manuals
  4. Indoor Furnishing
  5. Lustre series
  6. Installation instructions manual

Utopia Lustre series Installation Instructions Manual

Bathroom
Hide thumbs
Table of Contents

Advertisement

Quick Links

Bathroom Installation Instructions

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Lustre series and is the answer not in the manual?

Questions and answers

Related Manuals for Utopia Lustre series

Summary of Contents for Utopia Lustre series

  • Page 1 Bathroom Installation Instructions...

  • Page 2: Table Of Contents

    It is also advised that all doors and fascias are removed prior to fitting to avoid unnecessary damage occurring. Please note that some of Utopia’s units, sanitaryware and worktops are heavy. Always take care when lifting, and follow health and safety guidelines.

  • Page 3: Base Units

    Utopia Bathroom Group assumes that this/these product/s will be fitted by an experienced and competent installer. Failure to do so will result in the invalidation of Utopia’s guarantee. Under our policy of improvement we reserve the right to alter materials or specification in line with our continuing programme of product and service development.

  • Page 4: Fitting Wall Hung Base And Wall Units

    INSTALLATION INSTRUCTIONS Base Units FITTING WALL HUNG BASE UNITS AND WALL UNITS Units should be fitted by professional installers. All base units whether with legs or wall-hung come complete with leg sockets fitted for transit purposes. If the units are to be installed wall-hung, please remove these sockets prior to fixing.

  • Page 5: Adjusting A Soft Close Drawer Box

    Drawer boxes are factory installed and should not need to be adjusted. However, if adjustment is required, pull the drawer box out and remove the Utopia branded plastic cover cap. This will reveal the two adjustment screws. Use one of the screws to raise and lower the drawer box (see fig 1 A) and the other (see fig 1 B) to move it, left and right.

  • Page 6: Wc Fascia Cut Outs

    (see fig 6). Re-seal all cut edges. UTOPIA PUSH BUTTON CONCEALED CISTERNS The concealed cistern for use in Utopia Furniture is pneumatically operated by a small push button which is both aesthetically pleasing and functional. fig 2...

  • Page 7: Cut-Out Semi Recessed Washbasin Units

    Base Unit Cut-Outs CUT-OUT SEMI RECESSED WASHBASIN UNITS fig 1 The cut-out washbasin unit incorporates a void at the back to allow pipework to pass behind the unit. (see fig 1). WWW.UTOPIAGROUP .COM page 7...

  • Page 8: Wall Units

    INSTALLATION INSTRUCTIONS Wall Units FITTING WALL CABINETS, DELUXE MIRROR UNITS, DOUBLE FULL MIRROR UNITS, WALL CABINETS, OPEN SHELF UNITS AND QUBE MIRROR CABINET Wall cabinet hanging brackets are supplied with the unit. It is advised that a line is drawn along the length of the wall, level with where the units are to be fitted at the desired height above floor level.

  • Page 9: Mirror Cabinet Handle Fitting

    Wall Units MIRROR CABINET HANDLE FITTING fig 1 Please ensure all components are fitted in accordance with the diagram (see fig 1). Please fit hand tight only using a manual screwdriver. Do not overtighten as this may cause damage to the mirror door. DOOR ADJUSTMENT When adjustment is necessary to the doors, follow these directions (see fig 2): W - Lift this clip to release the door from the carcass...

  • Page 10: Mirrors

    INSTALLATION INSTRUCTIONS Mirrors FITTING A MIRROR Decide which way you wish to hang the mirror, horizontal or vertical. Insert the white plastic pegs into the carcass holes (see fig 1), ensuring they are pushed in properly, and straight. (Please note that once the white plastic inserts are fitted into the holes on the carcass backboard, they cannot be removed).

  • Page 11: Fitting Designer Illuminated, Curved And Modular Offset Mirrors

    Designer Illuminated, Curved and Modular Offset Mirrors Decide on the position that you want your mirror and mark a horizontal line on the wall. (see fig 1). Mark out the position of the supporting brackets. It is important that they are fitted as accurately as possible, so the mirror does not move left or right when installed.

  • Page 12: Lighting, Flyover Shelves And Cornice

    INSTALLATION INSTRUCTIONS Lighting, Flyover Shelves and Cornice We strongly recommend that a qualified electrician be used for the installation of fig 1 electrical products. example 1 FITTING FLYOVER SHELVES Three types of material may be used as flyover shelving; (a) 16mm carcass material (b) 28mm worktop material (c) Solid Surface worktop material All are fitted in the same way, by either;...

  • Page 13: Tall Units

    Tall Units FITTING A TALL GLASS SHELF DISPLAY UNIT AND ALL OTHER TALL UNITS With either drawers or cabinet. Drill the fixing holes in the back of the unit as follows: a In the top and bottom sections of the unit, mark the positions of the two fig 1 fixing holes as shown (see figs 1 and 2).

  • Page 14: Modular Units

    INSTALLATION INSTRUCTIONS Modular Units The recommended height from the floor to the top of the basin shown above as Y, is 900mm FITTING WALL-HUNG BASE UNITS AND WALL UNITS fig 1 fig 2 Wall hanging brackets need to be fixed to the carcass if supplied separately. The brackets should be fixed the correct way up by knocking four prongs into the holes at the rear of the carcass.

  • Page 15: Modular Mirror Fitting

    INSTALLATION INSTRUCTIONS Modular Units MODULAR WALL MIRROR FITTING fig 1 Determine the orientation of the mirror required for this installation, either vertical or horizontal (see fig 1). It is advised that a line is now drawn along the length of the wall, level with where the unit is to be fitted at the desired height above floor level at position x (see fig 2 and 3).

  • Page 16: Mirror Cabinet Handle Fitting

    fig 7 fig 8 fig 9 Modular Unit Mirror Door Handles and Door Hinge Adjustment MIRROR CABINET HANDLE FITTING fig 1 Please ensure all components are fitted in accordance with the diagram (see fig 1). Please fit hand tight only using a manual screwdriver. Do not overtighten as this may cause damage to the mirror door.

  • Page 17: Fitting A Square Profile Laminate Worktop

    Drawer boxes are factory installed and should not need to be adjusted. However, if adjustment is required, pull the drawer box out and remove the Utopia branded plastic cap. This will reveal the two adjustment screws. Use one of the screws to raise and lower the drawer box (see fig 4 A) and the other (see fig 4 B) to move it left and right.
  • Page 18 INSTALLATION INSTRUCTIONS Halo Units 1200 HINGED DOOR MIRROR UNIT fig 1 fig 2 Mirror door can be either left hand or right hand. Fitting the cabinet to the wall, Depress button to release hinge from backplate Remove the door from the unit, care needs to be taken due to the weight of the mirror door panel Note: the door hinges are fitted the reverse way to a normal hinged door (see fig 2) - the hinge back plate is fitted to the door not the unit side panel, to release the hinge and door...
  • Page 19 Halo and Qube Units TWIN BASE UNIT 650MM - 1200MM fig 1 Draw a line along the length of the wall for the wall brackets (fig 2), the line is approx. 30mm below worktop height, ensure that the line is drawn level. Measure between the gables ‘Y’...
  • Page 20 INSTALLATION INSTRUCTIONS Halo Units SIDE CABINET Open and remove the main drawer by lifting the drawer up and pull off runners. Push the top drawer so that it opens and lift off the runners. To fit wall brackets and how to mount and adjust cabinet refer to page 20. Fit and fix worktop or basin into position, refer to page 40 for full fittng instructions.
  • Page 21 i-Line Fitted and Freestanding Furniture i-LINE 50MM SIDE PANELS WITH FITTED FURNITURE 50mm tops and sides are fitted flush with the back of the units with almost no overhang around the sides and to the front fascia. See pages 3 and 4 for installing base units. There are two ways of installing 50mm side panels with fitted furniture.

  • Page 22: Www.utopiagroup .Com

    INSTALLATION INSTRUCTIONS i-Line Wall and Frameless Mirror Unit FITTING WALL UNITS fig 1 See page 9 of these instructions. FITTING AN i-LINE FRAMELESS MIRROR UNIT The frameless mirror is held onto the backboard with an integrated 50mm side panel with two keyhole grommets.

  • Page 23: Symmetry Furniture

    Symmetry Furniture FITTING SYMMETRY MODULAR BASE UNITS AND fig 2 fig 1 FITTED/FREESTANDING BASE UNITS It is advised that a line is drawn along the length of the wall, level with where the units are to be fitted at the desired height above floor level. The space between the floor and the level line unit is 175mm when using a plinth or as required for a modular unit.

  • Page 24: Decorative End Panels

    INSTALLATION INSTRUCTIONS Symmetry Furniture All units are fitted with extra leg sockets during manufacture. When installed next to a WC (see fig 1) unit a straight plinth is supplied so you will need to remove the leg sockets from the front curve of the unit before installation. To do this, insert a small flat-headed screwdriver into the centre section and carefully lever out the centre pin.

  • Page 25: Fitting Traditional Base Unit

    INSTALLATION INSTRUCTIONS Downton TRADITIONAL BASE UNITS fig 1 fig 2 Basin Support shelf The base unit comes in two parts. Base unit assembled (see fig 1). Worktop and Basin come separately. Front 1. Place and fix base unit into position (see fig 1). fig 3 2.

  • Page 26: Downton

    Downton This range of furniture is supplied assembled and can be placed in position for installation to start. Any electrical work must be completed by a qualified electrician. Mirror transformers could be set into the wall plaster behind the mirror, or in the recess on top of the unit keeping it to the back.

  • Page 27: Bath Panels

    INSTALLATION INSTRUCTIONS Bath Panels COMPONENT IDENTIFICATION MAGNET CATCH SOCKET AND PLATE CORNER SUPPORT KEKU CLIPS EXTENSION ONLY USE ROUND-HEADED ‘L’ BRACKET SCREWS WITH THE CATCH DOWEL LEG CLIP BOLT Including the Dualelle, Roundelle and Definity. Please note: The bath being fitted must have a wooden batten fitted under the bath rim to hold the bath panel clips.

  • Page 28: Definity Fitted Bath

    Definity Bath Panels DEFINITY FITTED BATH - CORNER OR RECESSED fig 1 INSTALLATION WALL Remove all protective film from panels before fixing together. Note in some instances the pre-drilled holes will be covered by the panels finish. These holes will need to be reinstated. PANEL NOTE when fitting a top rail this is to be done first.

  • Page 29: Free-Standing Bath

    Free-staning Bath WWW.UTOPIAGROUP .COM page 29...

  • Page 30: Fitting Symmetry Baths

    Assembly fig 1 fig 2 WWW.UTOPIAGROUP .COM page 30...
  • Page 31 WWW.UTOPIAGROUP .COM page 31...
  • Page 32 Symmetry Bath Side and End Panels NOTE: DEPENDING ON TILING, PANELS MAY NEED TO BE TRIMMED FOR A BETTER FIT TO THE WALL. Top Rail Keku clips Bracket fixed to top rail only 2mm gap 2mm gap Keku hook clip SYMMETRY BATHS fig 1 Please note - remove all protective film from panels before fixing them together.
  • Page 33 INSTALLATION INSTRUCTIONS Symmetry Bath Panel Keku clip Bracket fixed to Top Rail top rail only 2mm gap 2mm gap Keku clip SYMMETRY BATHS fig 1 Please note - remove all protective film from panels before fixing them together. Ensure the under side of this bath rim is fitted at a height which will give the required clearance for the panels and/or a bath end storage unit when fitting.
  • Page 34 Symmetry Bath Panel with End Storage Unit Keku clip Top Rail Bracket fixed to top rail only Keku clip 2mm gap 2mm gap Transit support. This should be removed prior to installation by cutting at the pre-marked “V” cuts fig 1 SYMMETRY BATHS Please note - remove all protective film from panels before fixing them together.

  • Page 35: Geo

    GEO DRAWER UNIT When fitting this unit draw a line along the length of the wall, level with where the units are to be fitted at the desired height - X (see fig 1 and fig 2). Fix the brackets to the wall with appropriate plugs and screws for your wall type (not supplied).

  • Page 36: Tap Holes

    Use a quality silicone seal around both hole cuts and insert sleeve and fit tap 35mm hole Nylon sleeve 52-54mm hole fig 4 fig 5 WORKTOP MOUNTED TAP Warning - For your information and guidance Utopia’s Solid Surface products are not suitable for use in a shower enclosure. WWW.UTOPIAGROUP .COM page 36...

  • Page 37: Solid Surface And Laminate Worktops

    Solid Surface and Laminate Worktops PLEASE READ THESE INSTRUCTIONS CAREFULLY BEFORE COMMENCING WORK All Solid Surface tops are packed together with a relevant fitting pack and are identified by a label which appears on the front of the box and the rear of the packaging.

  • Page 38: Fitting A Worktop

    INSTALLATION INSTRUCTIONS Worktops fig 1 FITTING A WORKTOP Position the worktop on the units and push up against the wall to enable you to mark (see fig 1). and measure for cutting If the worktop needs scribing to the wall contours do so using a compass and pencil (see fig 2).

  • Page 39: Installing A Washbasin Into A Worktop

    All worktops must be cut at points A, B and C and sealed with a good quality silicone (see fig 4) sealant as illustrated to accommodate a Utopia basin. This will allow the basin fig 3 to fit closely to the fascia of the unit below.

  • Page 40: Fitting A Solid Surface Apron Standard And Short Projection

    INSTALLATION INSTRUCTIONS Worktops FITTING A SOLID SURFACE APRON STANDARD fig 1 AND SHORT PROJECTION Position the fascia into the slot ensuring that the fascia is tight against the front edge of the slot. (see fig 1) Ensure that the apron remains central on the fascia, , and the distance that the top edge of the apron sits above the top edge of the fascia (a) is equal on both sides (see fig 2)
  • Page 41 Worktops 50mm Decorative Floating Shelf with Adjustable Support fig 1 Spirit Level (see fig 1) Draw a horizontal line on the wall at the desired height X Fix the concealed shelf supports to the wall using appropriate fixings for the wall type (not supplied).

  • Page 42: Roseberry Painted Products Fitting Instructions

    Roseberry Painted Products Fitting Instructions Please read instructions carefully before commencing fitting WWW.UTOPIAGROUP .COM page 42...
  • Page 43 WWW.UTOPIAGROUP .COM page 43...
  • Page 44 WWW.UTOPIAGROUP .COM page 44...
  • Page 45 For Fitting Basins and Worktops see page 49 WWW.UTOPIAGROUP .COM page 45...
  • Page 46 For Fitting Basins and Worktops see page 49 WWW.UTOPIAGROUP .COM page 46...
  • Page 47 WWW.UTOPIAGROUP .COM page 47...
  • Page 48 For Fitting Basins and Worktops see page 50 WWW.UTOPIAGROUP .COM page 48...
  • Page 49 WWW.UTOPIAGROUP .COM page 49...
  • Page 50 WWW.UTOPIAGROUP .COM page 50...
  • Page 51 WWW.UTOPIAGROUP .COM page 51...
  • Page 52 Care and Maintenance Instructions For Roseberry Painted Product’s Spills should be removed immediately using a clean cloth. Furniture should be regularly dusted with a soft cotton or micro-fibre cloth. For more thorough cleaning, occasionally wipe your furniture with a soft cloth dampened with a mild detergent solution. Surfaces should be thoroughly dried with a lint free cloth to prevent watermarks.

  • Page 53: Modular 2017 (Star, Lustre, Opula)

    Modular 2017 (Star, Lustre, Opula) WWW.UTOPIAGROUP .COM page 53...
  • Page 54 WWW.UTOPIAGROUP .COM page 54...
  • Page 55 WWW.UTOPIAGROUP .COM page 55...
  • Page 56 WWW.UTOPIAGROUP .COM page 56...
  • Page 57 WWW.UTOPIAGROUP .COM page 57...
  • Page 58 WWW.UTOPIAGROUP .COM page 58...
  • Page 59 WWW.UTOPIAGROUP .COM page 59...
  • Page 60 Utopia Furniture Limited, Springvale Avenue, Wolverhampton WV14 0QL Tel - 01902 406402 Fax - 01902 406401 nfo@utopiagroup.com utopiagroup.com Proudly designed and manufactured in Britain UFI - 07/17...

This manual is also suitable for:

Star seriesDownton seriesSymmetry seriesGeo seriesI-line modular seriesQube series ... Show all

Table of Contents