Table of Contents
Advertisement
Quick Links
MODEL W1766
1/2 HP POWER FEEDER
OWNER'S MANUAL
Phone: (360) 734-3482 • Online Technical Support: tech-support@shopfox.biz
COPYRIGHT © SEPTEMBER, 2007 BY WOODSTOCK INTERNATIONAL, INC., REVISED JULY, 2014 (MN)
WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE OR FORM WITHOUT
THE WRITTEN APPROVAL OF WOODSTOCK INTERNATIONAL, INC.
Printed in Taiwan
#9772CR
Advertisement
Table of Contents
Related Manuals for Woodstock Shopfox W1766
Summary of Contents for Woodstock Shopfox W1766
- Page 1 MODEL W1766 1/2 HP POWER FEEDER OWNER'S MANUAL Phone: (360) 734-3482 • Online Technical Support: tech-support@shopfox.biz COPYRIGHT © SEPTEMBER, 2007 BY WOODSTOCK INTERNATIONAL, INC., REVISED JULY, 2014 (MN) WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE OR FORM WITHOUT THE WRITTEN APPROVAL OF WOODSTOCK INTERNATIONAL, INC. Printed in Taiwan #9772CR...
- Page 2 This manual provides critical safety instructions on the proper setup, operation, maintenance, and service of this machine/tool. Save this document, refer to it often, and use it to instruct other operators. Failure to read, understand and follow the instructions in this manual may result in fire or serious personal injury—including amputation, electrocution, or death.
-
Page 3: Table Of Contents
Contents INTRODUCTION ........2 OPERATIONS ........16 Woodstock Technical Support ....2 General .......... 16 Data Sheet ........3 Changing Feed Speed ......17 ACCESSORIES ........18 SAFETY ..........6 Standard Safety Instructions ....6 Power Feeder Accessories ....18 Additional Safety for Power Feeders .. -
Page 4: Introduction
Woodstock International, Inc. is committed to customer satisfaction. Our intent with this manual is to include the basic information for safety, setup, operation, maintenance, and service of this product. -
Page 5: Data Sheet
W1766 ⁄ HP Power Feeder MACHINE MACHINE SPECIFICATIONS SPECIFICATIONS Phone #: (360) 734–3482 • Online Tech Support: tech–support@shopfox.biz • Web: www.shopfox.biz MODEL W1766 Data Sheet 1/2 HP POWER FEEDER Motor Type ..................TEFC Capacitor Start Induction Horsepower ......................1/2 HP Voltage ........................ - Page 6 W1766 ⁄ HP Power Feeder Shipping Dimensions Carton #1 Type ......................Cardboard Content ......................Machine Weight ......................70 lbs. Length/Width/Height ................. 20 x 11 x 19 in. Carton #2 Type ......................Cardboard Content ......................Stand Weight ......................48 lbs. Length/Width/Height ................... 30 x 11 x 9 in. Electrical Switch ....................
- Page 7 W1766 ⁄ HP Power Feeder Controls and Features Vertical Travel Upper Elbow Handcrank Joint Lock Lower Elbow Horizontal ⁄ Joint Lock Vertical Travel Lock Motor Travel Lock Horizontal Handcrank Gearbox Oil Plug Labeled "OIL" Located on Top of Case Behind Motor Rotary Movement Lock...
-
Page 8: Safety
W1766 ⁄ HP Power Feeder SAFETY READ MANUAL BEFORE OPERATING MACHINE. FAILURE TO FOLLOW INSTRUCTIONS BELOW WILL RESULT IN PERSONAL INJURY. Indicates an imminently hazardous situation which, if not avoided, WILL result in death or serious injury. Indicates a potentially hazardous situation which, if not avoided, COULD result in death or serious injury. - Page 9 W1766 ⁄ HP Power Feeder 10. NEVER LEAVE WHEN MACHINE IS RUNNING. Turn power off and allow all moving parts to come to a complete stop before leaving machine unattended. 11. DO NOT USE IN DANGEROUS ENVIRONMENTS. DO NOT use machinery in damp, wet locations, or where any flammable or noxious fumes may exist.
-
Page 10: Additional Safety For Power Feeders
W1766 ⁄ HP Power Feeder Additional Safety for Power Feeders READ and understand this USE this and other machinery with caution entire instruction manual and respect. Always consider safety first, before using this machine. as it applies to your individual working Serious personal injury conditions. -
Page 11: Electrical
W1766 ⁄ HP Power Feeder ELECTRICAL The machine must be properly set up before it is safe to operate. DO NOT connect this machine to the power source until instructed to do so in the "Test Run" portion of this manual. 220V Operation 6-15 R 6-15 P... -
Page 12: Setup
W1766 ⁄ HP Power Feeder SETUP Unpacking This machine has been carefully packaged for safe transportation. If you notice the machine has been damaged during shipping, please contact your authorized Shop Fox dealer immediately. Inventory Keep machine disconnected from The following is a description of the main components power until instructed otherwise. -
Page 13: Machine Placement
W1766 ⁄ HP Power Feeder Machine Placement Cleaning Machine • Table Load: This power feeder distributes Some unpainted parts of your power feeder a heavy load in a small footprint. Some may be coated with oil or a waxy grease that machine table tops may require additional protects them from corrosion during shipment. -
Page 14: Assembly
W1766 ⁄ HP Power Feeder Assembly To correctly position this power feeder on your table top, first gather the stand parts shown in Figure 5 and assemble the power feeder stand (refer to the parts diagram for any intricate details). Next, connect the stand to the power feeder as shown in Figure 6, and then refer to Base Mounting on Page 14. -
Page 15: Base Mounting
W1766 ⁄ HP Power Feeder Base Mounting Assemble the power feeder before you mount the Also, you must be able to adjust the power base to determine where on the table top to drill feeder so it points towards the machine fence slightly (see Figure 8). - Page 16 W1766 ⁄ HP Power Feeder Through-Bolt Mounting We recommend that you mount your new power feeder to the machine table with through bolts, nuts and washers (Figure 9). This option will give the most rigidity and clamping strength to prevent the feeder base from Bolt Feeder twisting out of alignment during use.
-
Page 17: Test Run
W1766 ⁄ HP Power Feeder Test Run Once power feeder assembly is complete and mounted on the table, you must test run your power feeder to make sure it runs properly. If, during the test run, you cannot easily locate the source of an unusual noise or vibration, stop using the power feeder immediately, then review the Troubleshooting table on Page 21. -
Page 18: Operations
W1766 ⁄ HP Power Feeder OPERATIONS General This machine will perform many types of operations that are beyond the scope of this manual. Many of these operations can be dangerous or deadly if performed incorrectly. The instructions in this section are written with the understanding that the operator has the necessary knowledge and skills to operate this machine. -
Page 19: Changing Feed Speed
W1766 ⁄ HP Power Feeder Changing Feed Speed Your power feeder has the option to feed a workpiece at four different feed rates: 9.5, 15, 25, and 38 feet per minute. These rates are achieved by changing the combination of change gears in the power feeder gear box. -
Page 20: Accessories
Inc. Dealer. If you do not have a dealer in your area, these products are also available through online dealers. Please call or e-mail Woodstock International Inc. Customer Service to get a current listing of dealers at: 1-800-545-8420 or at sales@woodstockint.com. -
Page 21: Maintenance
W1766 ⁄ HP Power Feeder MAINTENANCE General Regular periodic maintenance on your machine will ensure its optimum performance. Make a habit of inspecting your machine each time you use it. Check for the following conditions and repair or replace when necessary: •... -
Page 22: Service
If you require additional machine service not included in this section, please contact Woodstock International Technical Support at (360) 734-3482 or send e-mail to: tech-support@shopfox.biz. MAKE SURE that your machine is... -
Page 23: Troubleshooting
W1766 ⁄ HP Power Feeder Troubleshooting This section covers the most common problems and corrections with this type of machine. WARNING! DO NOT make any adjustments until power is disconnected and moving parts have come to a complete stop! PROBLEM POSSIBLE CAUSE CORRECTIVE ACTION Motor will not start. -
Page 24: Electrical
W1766 ⁄ HP Power Feeder Electrical Model W1766 Power Feeder Wiring Diagram Motor Power and 220V Direction Switch Motor Side A Side B Ground Capacitor Start Capacitor 220 VAC Ground 6-15 Plug Figure 16. Motor capacitor. Figure 17. Motor power and direction switch. -
Page 25: Parts
W1766 1/2 HP Power Feeder PARTS -23-... - Page 26 W1766 1/2 HP Power Feeder REF PART # DESCRIPTION PART # DESCRIPTION X1766001 COVER X1766044 GREASE FITTING M6-1 STRAIGHT X1766003 CONE X1766045 SPROCKET CASE X1766004 LOCK WASHER 8MM X1766046 TORSION SPRING 3.5 X 100 X1766005 CAP SCREW M8-1.25 X 25 X1766047 CASE COVER X1766007...
-
Page 27: Stand
W1766 1/2 HP Power Feeder Stand REF PART # DESCRIPTION REF PART # DESCRIPTION X1766100 COLUMN BASE X1766128 FLAT WASHER 12MM X1766102 STUD M12-1.75 X 70 X1766129 CAP SCREW M12-1.75 X 50 X1766103 FLAT WASHER 12MM X1766131 HORIZONTAL TUBE CONE X1766104 T-HANDLE X1766134... -
Page 28: Label Placement
MUST maintain the original location and readability of all labels on this machine. If any label is removed or becomes unreadable, REPLACE that label before allowing the machine to enter service again. Contact Woodstock International, Inc. at (360) 734-3482 or www. shopfoxtools.com to order new labels. -
Page 29: Warranty Registration
W1766 1/2 HP Power Feeder Warranty Registration Name ___________________________________________________________________________________ Street __________________________________________________________________________________ City _________________________ State ___________________________Zip ________________________ Phone # ______________________ Email___________________________Invoice # ___________________ Model #_________Serial #______________Dealer Name__________________Purchase Date___________ The following information is given on a voluntary basis. It will be used for marketing purposes to help us develop better products and services. - Page 30 FOLD ALONG DOTTED LINE Place Stamp Here WOODSTOCK INTERNATIONAL INC. P.O. BOX 2309 BELLINGHAM, WA 98227-2309 FOLD ALONG DOTTED LINE TAPE ALONG EDGES--PLEASE DO NOT STAPLE...
- Page 31 We do not warrant that machinery complies with the provisions of any law or acts. In no event shall Woodstock International, Inc.'s liability under this warranty exceed the purchase price paid for the product, and any legal actions brought against Woodstock International, Inc.
Need help?
Do you have a question about the Shopfox W1766 and is the answer not in the manual?
Questions and answers