Woodstock H0626 Instruction Manual
  1. Manuals
  2. Brands
  3. Woodstock Manuals
  4. Power Tool
  5. H0626
  6. Instruction manual

Woodstock H0626 Instruction Manual

Oscillating drill press
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
MODEL W1668
1
13
⁄
" Oscillating Drill Press
4

INSTRUCTION MANUAL

Phone: 1-800-840-8420 • On-Line Technical Support: tech-support@woodstockint.com
COPYRIGHT © 2000 BY WOODSTOCK INTERNATIONAL, INC.
WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE OR FORM WITHOUT
THE WRITTEN APPROVAL OF WOODSTOCK INTERNATIONAL, INC.
Printed in China

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the H0626 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Woodstock H0626

Summary of Contents for Woodstock H0626

  • Page 1: Instruction Manual

    MODEL W1668 ⁄ " Oscillating Drill Press INSTRUCTION MANUAL Phone: 1-800-840-8420 • On-Line Technical Support: tech-support@woodstockint.com COPYRIGHT © 2000 BY WOODSTOCK INTERNATIONAL, INC. WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE OR FORM WITHOUT THE WRITTEN APPROVAL OF WOODSTOCK INTERNATIONAL, INC.

  • Page 2: Table Of Contents

    Table Of Contents INTRODUCTION ABOUT YOUR NEW DRILL PRESS ...2 WOODSTOCK SERVICE AND SUPPORT ...2 WARRANTY AND RETURNS ...3 MACHINE SPECIFICATIONS ...3 SAFETY...4 STANDARD SAFETY INSTRUCTIONS ...4-5 DRILL PRESS SAFETY ...5 ELECTRICAL REQUIREMENTS ...6 AVOIDING POTENTIAL INJURIES ...7 ASSEMBLY INSTRUCTIONS ...8 BOX CONTENTS ...8...

  • Page 3: Introduction

    ® Model W1668 is a drill press and oscillating sander in one compact machine. It is Shop Fox capable of a wide variety of drilling and sanding operations. A sanding spindle is included for use with drums ranging in size from 1"...

  • Page 4: Warranty And Returns

    WARRANTY AND RETURNS Woodstock International, Inc. warrants all SHOP FOX ship and materials for a period of 2 years from the date of original purchase by the original owner. This warranty does not apply to defects due directly or indirectly to misuse, abuse, negligence or accidents, lack of maintenance, or to repair or alterations made or specifically authorized by anyone other than Woodstock International, Inc.

  • Page 5: Safety

    SAFETY FIRST! READ MANUAL BEFORE OPERATING MACHINE FAILURE TO FOLLOW INSTRUCTIONS BELOW WILL RESULT IN PERSONAL INJURY Indicates an imminently hazardous situation which, if not avoided, WILL result in death or serious injury. Indicates a potentially hazardous situation which, if not avoided, COULD result in death or serious injury.

  • Page 6: Drill Press Safety

    Additional Safety Instructions For Drill Presses Always operate your drill press at speeds that are appropriate for the drill bit size and the mate- rial that you are drilling. Feed the drill bit evenly into the workpiece. Back the bit out of deep holes and clear the chips with a brush after you have turned the machine off.

  • Page 7: Electrical Requirements

    Add up the load rat- ings of all machines on the circuit. If this num- ber exceeds the rating of the circuit breaker or fuse, use a different outlet.

  • Page 8: Avoiding Potential Injuries

    AVOIDING POTENTIAL INJURIES Figure 2. Never drill, holding workpiece by hand. Figure 3. Keep fingers away from spinning tool. Fig. 4. Remove Switch Safety Key when not in use. Figure 5. Remove handles when using oscillating mode.

  • Page 9: Assembly Instructions

    ASSEMBLY INSTRUCTIONS Figure 6. Components laid out for identification. The following is a description of the components shipped with the Shop Fox Press. It is recommended that the components be laid out in a similar fashion to those in Figure 6. This will help in identification before beginning assembly.

  • Page 10: Base And Column

    Figure 7. Using holes in base as drill guide. Figure 8. Installing the dust port. ASSEMBLY ® W1668 Oscillating Drill Press are assembled at the factory, Base/Column 1. Ensure machine is unplugged before begin- ning assembly! 2. Place base on a stable work bench. Make sure the work bench will handle the weight of the drill press and workpiece.

  • Page 11: Table Support

    Table Support 1. Thread the 12mm table lock handle 3 turns into the table support bracket. 2. Insert the pinion into the hole on the side of the table support bracket from the inside, starting with the pinion shaft. Figure 9. Align setscrew in crank handle with flat, Figure 10, on pinion shaft and secure using ®...

  • Page 12: Mounting Table

    Figure 12. Hold rack in position while installing. Figure 13. Inside bevel in the correct position. Figure 14. Lock shoe in place and secured. Table Support, Cont. 4. Examine the rack and note that the gear teeth extend further on one end than the other.

  • Page 13: Headstock

    2. Align the headstock directly over the foot of the base by using a plumb bob. Lay a mea- suring tape or ruler across the drill press base and find its center. Suspend the plumb line from the center of the headstock label as in Figure 16 and lower the bob until it is near the tape/ruler.

  • Page 14: Drill Chuck

    1 and 2. Handles Three handles are supplied with your new Oscillating Drill Press. Thread them into the hub as in Figure 20. Unplug remove handles before using the oscillating fea- ture.

  • Page 15: Adjustments

    Unplug the drill press before changing speeds. The Oscillating Drill Press has 12 speeds ranging from 250 to 3050 RPM. There is a speed chart located under the belt guard and one on the fol- lowing page.

  • Page 16: Speed Change

    Figure 25. Actual stop depth being measured. More About Speed Change Spindle Adjustments Your new drill press comes fitted with a depth stop for use when drilling. Follow the instruc- tions below for use. 1. Loosen the depth collar lock knob. Figure 2.

  • Page 17: Oscillating Feature

    One of the great features of the W1668 Drill Press is its capability for oscillating sanding. The drill press can be converted from drilling opera- tions to sanding operations in just a few steps. 1. Unplug the drill press and remove the spindle handles.

  • Page 18: Table Adjustments

    Turn the table hand crank to raise or lower the table. Figure 27. 2. The table can be adjusted out of the way so the base of the drill press may be used to support the workpiece for drilling opera- tions only. Loosen the table lock knob and pivot the table to the back side of the col- umn.

  • Page 19: Operations

    Pull the START paddle. Make sure that your finger is poised over the paddle,as in Figure 30, just in case there is a problem. The drill press should run smoothly, with little or no vibration or rubbing noises. Strange or unnatural noises require you to stop the machine, investigate and correct before continuing.

  • Page 20: Drill Changes

    Figure 31. Installing bit. Figure 32. Chuck key engaged. Installing the sanding drum spindle is identical to installing a drill bit. However, it is important to install the paper and drum before installing the spindle into the drill chuck. See your local retailer for drums and paper.

  • Page 21: Maintenance

    Regular periodic maintenance on your Model W1668 Oscillating Drill Press will ensure its opti- mum performance. Make a habit of inspecting your drill press each time you use it. Check for the following conditions and repair or replace when necessary.

  • Page 22: Closure

    Trade journals, woodworking magazines, and your As with all power tools, there is danger asso- ciated with the Model W1668 Drill Press. Use the tool with respect and caution to lessen the possibility of mechanical damage or operator injury.
  • Page 24 PART # DESCRIPTION X1668001 BASE X1668002 COLUMN FLANGE X1668003 COLUMN X1668004 TABLE BRACKET XPB32M HEX BOLT M10-1.5 X 25 X1668007 RACK X1668008 COLUMN RING XPSS01M SET SCREW M6-1.0 X 10 X1668010 TABLE BRACKET X1668011 TABLE X1668012 WORM PINION X1668013 LOCK HANDLE M10 X1668014 LOCK SHOE X1668015...

  • Page 25: Your Notes

    NOTES:...
  • Page 26 ___Jointer ___Lathe ___Mortiser ___Other__________________________________________________ Which benchtop tools do you own? Check all that apply. ___1" x 42" Belt Sander ___5" - 8" Drill Press ___8" Table Saw ___8" - 10" Bandsaw ___Disc/Belt Sander ___Mini Jointer ___Other__________________________________________________ Which portable/hand held power tools do you own? Check all that apply.
  • Page 27 FOLD ALONG DOTTED LINE FOLD ALONG DOTTED LINE WOODSTOCK INTERNATIONAL, INC. P.O. BOX 2309 BELLINGHAM, WA 98227-2309 TAPE ALONG EDGES--PLEASE DO NOT STAPLE Place Stamp Here...

This manual is also suitable for:

W1668

Table of Contents