Advertisement
PLUG
CAP
COLLECTOR
DRAIN
TUBE
(BLUE
& WHITE
STRIPED)
COLLECTOR
TUBE
(PINK)
COLLECTOR
BOX
--_
TUBE
(GREEN)
(MOLDED)
DRAIN
TUBE
(BEHIND
COLLECTOR
BOX
DRAIN
TUBE)
DRAIN
TUBE
(BLUE)
FACTORY-SUPPLIED
DRAIN
TUBE
COUPLING
(LEFT
DRAIN
OPTION)
FIELD-INSTALLED
FACTORY-SUPPLiED
DRAIN
TUBE
FIELD-INSTALLED
FACTORY-SUPPLIED
V_-IN.
CPVC
STREET
ELBOWS
(2) FOR
LEFT
DRAIN
OPTION
FIELD-INSTALLED
FACTORY-SUPPLIED
DRAIN
TUBE
COUPLING
(RIGHT
DRAIN
OPTION)
A94163
Fig. 6--Factory-SNpped
Upflow Tube Configuration
(Shown With Blower Access
Panel Removed}
b. Remove
and discard
casing
drain
hole plug
button
from
desired
side.
c Install
&ain
tube coupling
grommet
(factor-supplied
in
loose parts bag)
in selected
casing
hole.
& Slide drain
robe coupling
di_ctok_'°supplied
in loose parts
bag) through
grommet
ensuring
tong end of coupling
fi_ces
blower.
e. Cement
2 factory°supplied
1i2qn.
stleet
CPVC
elbows
to
the rigid drain tube connection
on the condensate
trap. (See
Fig.
6.)
These
elbows
must
be
cemented
together
and
cemented
to condensate
trap drain
connection.
NOTE:
Failure to use CPV(
elbows
may allow
&ain to kink and
prevent
draining.
t_ Connect
larger
diameter
drain
tube
and clamp
(factory°
supplied
in loose parts bag)
to condensate
trap and clamp
securely.
g. Route
robe to coupling
and cut to appropriate
length.
h. Attach
robe to coupling
and clamp
securely.
(ONDENSATE
TRAP LOCATION (ALTERNATE
UPFLOW
ORIENTATION)
An alternate location fbr the condensate tlap is the left-hand side
of casing. (See Fig 2 and 7)
PLUG
CAP
COLLECTOR
BOX
DRAIN
TUBE
(BLUE
& WHITE
STRIPED)
COLLECTOR
BOX
TUBE
(PINK)
COLLECTOR
BOX
TUBE
(GREEN)
COLLECTOR
BOX
DRAIN
TUBE
(BLUE)
TRAP
HOUSING
DRAIN
TUBE
(VIOLET)
O O
A94164
Fig. 7--Alternate
Upflow Tube Configuration
and
Trap Location
--9
NOTE:
If the alternate
tef_-hand
side of casing
location
is used_
the factory-connected
drain
and relief port robes must he discon-
nected
and modified
for attachment
See Condensate
Trap Tubing
(Alternate
Upflow
Orientation)
section
for tubing
attachment
To relocate
condensate
trap to the te_t-hand
side,
perfbrm
the
following:
1
Remove
3 tubes connected
to condensate
t_ap.
2
Remove
trap from blower
shelf by gently
pushing
tabs inward
and rotating
trap.
3. Install
casing
hole filler
cap (_i_ctory=supplied
in loose parts
bag) into blower
shelf hole where
trap was removed.
CARBON
MONOXIDE
POISONING
HAZARD
Failure
to follow
this warning
eoutd result
in personal
inju W
or death,
Casing
hole filler cap must
be installed
in blower
shelf hole
when condensate
trap is relocated.
4
Install
condensate
trap
into
left=hand
side
casing
hole
by
inserting
tube
cormection
stubs
through
casing
hole
and
rotating
until tabs snap into locking
position.
5. Fill unused
condensate
tlap
casing
holes
with
plastic
filler
caps (bactory=supplied
in loose parts
bag).
Advertisement
