Advertisement
PLUG
CAP
BOX DRAIN TUBE (BLUE)
COLLECTOR BOX TUBE (GREEN)
BOX EXTENSION TUBE
COLLECTOR BOX TUBE (PINK)
BOX RELOCATED HERE
COLLECTOR
BOX DRAIN
TUBE
(BLUE
AND WHITE
STRIPED)
INDUCER
HOUSING
DRAIN
TUBE
(VIOLET)
COLLECTOR
BOX
EXTENSION
TUBE
CONDENSATE
TRAP
A00214
Fig. 12--Horizontal
Right Tube Configuration
NOTE:
In (anada,
installations
shall
be
in accordance
with
current
NSCNGPIC
Installation
Codes
andor
local
codes.
NOTE:
The auxilial_- junction
box (J°Box) MUST
be relocated
to
opposite
side
of _/rnace
casing.
(See
Fig.
12.)
See Electrical
Connection
section
_br J-Box relocation.
CONDENSATE
TRAP
LOCATION
The condensate
tlap
must be removed
from
the factor-installed
blower
shelf location
and relocated
in selected
application
location
as shown
in Fig. 2 or 12.
To relocate
condensate
trap from
the
blower
shelf
to desired
location,
perform
the fbllowing:
1. Remove
3 tubes connected
to condensate
trap.
2. Remove
tlap fi'om blower
shelf by gently
pushing
tabs inward
and rotating
trap.
3. Install
casing
hole filler
cap (factov-supplied
in loose
parts
bag) into blower
shelf
hole where
tlap was remo_ ed.
-->
(ARBON
MONOXIDE
POISONING
HAZARD
Failure
to follow
this warning
could result
in personal
in3u D'
or death.
Casing
hole filler
cap must be installed
in blower
shelf
hole
when
condensate
trap is relocated.
4. Install
condensate
trap
into casing
hole
by
inserting
tube
connection
stubs through
casing
hole and rotating
until tabs
snap into locking
position.
5. Fill unused
condensate
trap casing
holes
with
plastic
filler
caps (_Sctoryosupplied
in loose parts bag)
12
(ONDENSATE
TRAP TL BING
NOTE:
See Fig
12 or robe routing
label on main furnace
door to
check
for proper
connections
1. Collector
Box Drain
Tube
a
Remove
_ctoryoinsta!led
plug from LOWER
collector
box
drain robe (blue and white
striped
label).
b. Install
removed
clamp
and plug into UPPER
collector
box
&ain tube (blue label) which
was previously
connected
to
condensate
tlap.
c. Connect
LOWER
collector
box drain robe (blue and white
striped
label) to condensate
trap. Tube does not need to be
cut.
d. (lamp
robe to prevent
any condensate
leakage.
2. Inducer
Housing
Drain Tube
a. Remove
fhctoryoinstalled
cap and clamp
from
LOWER
inducer
housing
drain connection.
b. Remove
and discard
UPPER
(molded)
inducer
housing
&ain robe which
was previously
connected
to condensate
tlap.
c. Install
cap and clamp
on UPPER
inducer
housing
&ain
connection
where
molded
&ain robe was removed.
d. Use inducer
housing
&ain extension
tube (violet
label and
factory-supplied
in loose parts
bag)
to connect
LOWER
inducer
housing
&ain connection
to condensate
trap.
e. Detem?ine
appropriate
length,
cuk
and
connect
robe
to
condensate
trap.
_ Clamp
robe to prevent
any condensate
leakage.
3. Relief
Port Tube
Refer
to
Pressure
Switch
Tubing
section
_br connection
procedure.
Advertisement
