Adjustments - Sharp MX-FN10 Service Manual

[8] ADJUSTMENTS

MX-FN10
1. Finisher/saddle unit and Punch unit
1) Select "FINISHER ADJUSTMENT" in SIM 3-10.
2) Select a setup item and change the setup value.
SIMULATION NO.03-10
TEST
FINISHER ADJUSTMENT
A : 50 : SADDLE POSITION
A
50
B : 50 : FOLDING POSITION
C : 50 : FRONT ADJUST
D : 50 : REAR ADJUST
E : 50 : STAPLE REAR
F : 50 : STAPLE REAR R
G : 50 : STAPLE FRONT
H : 50 : STAPLE FRONT R
I : 50 : STAPLE BOTH
J : 50 : STAPLE PITCH
K : 50 : PUNCH CENTER
: PUNCH HOLE
L : 50
10 key
SIMULATION NO.03-10
TEST
FINISHER ADJUSTMENT
A : 30 : SADDLE POSITION
A
30
B : 50 : FOLDING POSITION
C : 50 : FRONT ADJUST
D : 50 : REAR ADJUST
E : 50 : STAPLE REAR
F : 50 : STAPLE REAR R
G : 50 : STAPLE FRONT
H : 50 : STAPLE FRONT R
I : 50 : STAPLE BOTH
J : 50 : STAPLE PITCH
K : 50 : PUNCH CENTER
L : 50 : PUNCH HOLE
Adjustable setup range is as follows.
<Set range and default value of each set value>
Item Display
SADDLE Saddle binding
A
POSITION
FOLDING Saddle folding position
B
POSITION adjustment
FRONT Alignment position
C
ADJUST adjustment (Front)
REAR Alignment position
D
ADJUST adjustment (Rear)
STAPLE Staple binding position
E REAR adjustment (Rear one
position)
STAPLE Staple binding position
F REAR R adjustment (Rear one
position/ R system)
STAPLE Staple binding position
G FRONT adjustment (Front one
position)
STAPLE Staple binding position
H FRONT R adjustment (Front one
position/ R system)
STAPLE Staple binding position
I BOTH adjustment (Two positions
center)
STAPLE Staple binding position
J PITCH adjustment (Two positions
pitch)
PUNCH Punch center adjustment
K
CENTER
CLOSE
OK
OK
CLOSE
OK
Set
Item Default
range
25 - 75 50
25 - 75 50
35 - 65 50
35 - 65 50
25 - 75 50
45 - 75 50
25 - 75 50
25 - 55 50
45 - 55 50
35 - 62 50
35 - 65 50
MX-FN10 ADJUSTMENTS 8 – 1
Service Manual
Item Display
PUNCH
L
HOLE
SADDLE_A
M DJUST_
POS
GRIPPER_
N
0
POS
<Amount of change and change direction for each set value>
Item Display
A SADDLE
POSITION
B FOLDING
POSITION
C FRONT
ADJUST
0
D REAR
ADJUST
E STAPLE
REAR
F STAPLE
REAR R
G STAPLE
FRONT
H STAPLE
FRONT R
I STAPLE
BOTH
Item
range
Punch hole position 30 - 60
adjustment
Saddle alignment position 35 - 65
adjustment
Gripper exit position 35 - 65
adjustment
Item Change Change direction
Saddle 0.2mm Large value: The binding
binding position is lower than the
center.
Small value: The binding
position is upper than the
center.
Saddle 0.2mm Large value: The folding
folding position is lower than the
position center.
adjustment Small value: The folding
position is upper than the
center.
Alignment 0.2mm Large value: The
position alignment plate position is
adjustment shifted to the center.
(Front) Small value: The
alignment plate position is
shifted to the outside.
Alignment 0.2mm Large value: The
position alignment plate position is
adjustment shifted to the center.
(Rear) Small value: The
alignment plate position is
shifted to the outside.
Staple 0.2mm Large value: The distance
binding between the staple
position position and the paper
adjustment edge becomes longer.
(Rear one Small value: The distance
position) between the staple
position and the paper
edge becomes shorter.
Staple 0.2mm Large value: The distance
binding between the staple
position position and the paper
adjustment edge becomes longer.
(Rear one Small value: The distance
position/ R between the staple
system) position and the paper
edge becomes shorter.
Staple 0.2mm Large value: The distance
binding between the staple
position position and the paper
adjustment edge becomes shorter.
(Front one Small value: The distance
position) between the staple
position and the paper
edge becomes longer.
Staple 0.2mm Large value: The distance
binding between the staple
position position and the paper
adjustment edge becomes shorter.
(Front one Small value: The distance
position/ R between the staple
system) position and the paper
edge becomes longer.
Staple 0.2mm Large value: The staple
binding position is shifted to the
position front side from the center.
adjustment Small value: The staple
(Two position is shifted to the
positions rear side from the center.
center)
Set
Default
50
50
50