Dimensions W 878 x D 729 x H 980 mm Occupied dimension W 880 x D 730 Weight Approximately 175 kg Installation/Maintenance By service person Heater AC 18W x 2 36W (By service parts: 0PQC4180431//) MX-LCX5 SPECIFICATIONS 1 – 1...
Page 3
Main 100 (4.0) 100 (4.0) 100 (4.0) max Main 320 (12.5) 320 (12.5) 320 (12.5) min Sub 140 (5.5) 140 (5.5) 140 (5.5) max Sub 470 (18.5) 470 (18.5) 470 (18.5) Special – Size uncertain MX-LCX5 SPECIFICATIONS 1 – 2...
Gear UKOG-0307FCZZ [Note 1] Replacement reference: Replace according to each paper feed counter value. MX-LCX5 Paper feed tray 1, 2, 3: 200K or 1 year Torque limiter: 800K (NOTE) Paper feed section roller life Each roller life is as shown on the left. When, therefore, a certain paper feed unit is excessively used, its life may be expired before the mainte- nance timing.
[C] Left rear cover (screw x 6) [D] Top cover (screw x 5) [E] Front door (stopper x 1) NOTE: While lifting the top cover, remove the snap ring and front door. [F] Paper slot cover (screw x 2) MX-LCX5 REPLACEMENT AND ADJUSTMENT 3 – 1...
[B] Knobs (x 3) (screw x 1 ea.) [C] Upper inner cover (screw x 2) [D] Knob (screw x 1) [E] Lower inner cover (screw x 1) [F] Paper feed unit (connector x 1, screw x 2) MX-LCX5 REPLACEMENT AND ADJUSTMENT 3 – 2...
Page 7
5th Lift Motor • Rear cover. (see 2.) [C] Motor unit (screw x 4, connector x 1) [D] 5th lift motor (screw x 2, Clip x 1, Coupling x 1, Spring x 1) MX-LCX5 REPLACEMENT AND ADJUSTMENT 3 – 3...
[B] 6th Transport sensor (screw x 1, connector x 1) 10. Side registration adjustment 8. Main control board • Remove the rear covers. (see 2.) [A] Main control board (screw x 6, Standoffs x 2, connector x All). MX-LCX5 REPLACEMENT AND ADJUSTMENT 3 – 5...
• Disconnect the LCT from the copier. [D] Cover (screw x 2, clamp x 2) [E] Image position sensor board (screw x 2, connector x 2, clamp x Remove the rear cabinet. (6 screws) MX-LCX5 REPLACEMENT AND ADJUSTMENT 3 – 6...
Page 11
Screw (x 2) harness Heater harness section Snap band fixing Interface harness Install two heaters with two screws fro each of them. Earth fixing screw Attach the clamp. Snap band fixing Clamp (2 positions) MX-LCX5 REPLACEMENT AND ADJUSTMENT 3 – 7...
Page 12
Install the rear cabinet, and fix it with the fixing screw. Fix the harness with the clamp. Snap band fixing Connect the heater and the harness. Install the heater cover. (3 screws) MX-LCX5 REPLACEMENT AND ADJUSTMENT 3 – 8...
The paper feed motor drives the pick-up roller [C] and the paper feed roller [D]. The grip motor drives the grip roller [E] that feeds the paper out of the tray, and the separation roller [F]. MX-LCX5 DETAILED DESCRIPTIONS 4 – 1...
YES: Detected automatically NO: Not detected automatically. Requires size setting change with the "Tray Paper Setting" key on the copier operation panel to detect the desired paper size. H: Sensor OFF L: Sensor ON MX-LCX5 DETAILED DESCRIPTIONS 4 – 2...
NOTE: When the actuator enters the gap of the near end sensor [E], the machine signals near end. Finally, when the last sheet feeds, the paper end sensor signals that the tray is empty. MX-LCX5 DETAILED DESCRIPTIONS 4 – 3...
Feed Slot (from Bypass Tray) *1: Each feed unit has 1 paper feed motor that drives the pick-up roller and paper feed roller, and 1 grip motor that drives the separa- tion roller and grip roller. MX-LCX5 OVERALL MECHANICAL INFORMATION 5 – 1...
5th Paper Feed Motor SOL5 6th Pick-up Solenoid 5th Transport Motor SOL6 6th Separation Solenoid 6th Grip Motor Door Safety Switch 6th Lift Motor 6th Paper Feed Motor 6th Transport Motor LCT Exit Motor MX-LCX5 OVERALL MECHANICAL INFORMATION 5 – 2...
4th Relay Sensor – Lower 4th Relay Sensor – Upper 4th Transport Sensor 5th Paper Feed Sensor 5th Relay Sensor 5th Transport Sensor 6th Paper Feed Sensor 6th Relay Sensor 6th Transport Sensor LCT Exit Sensor MX-LCX5 OVERALL MECHANICAL INFORMATION 5 – 3...
Page 19
5th Transport Detects jams in the paper path where (L2TS) Sensor the transport motor feeds the paper from the 5th tray. MX-LCX5 OVERALL MECHANICAL INFORMATION 5 – 4...
Page 20
An interlock safety switch that detects (LILSW) Switch when the front door is opened and closed. Other Name Description H1, H2 Anti-Condensation Evaporates moisture around the trays in Heaters the LCT (230V 18W). This is an option MX-LCX5 OVERALL MECHANICAL INFORMATION 5 – 5...
Page 21
For 2nd Tray SOL2 For 2nd Tray Intermediate Sensor For 3rd Tray Pick-Up Solenoid Connecting Unit Sensor SOL5 For 2nd Tray Reverse Solenoid SOL3 For 3rd Tray Pick-Up Solenoid SOL6 For 3rd Tray MX-LCX5 OVERALL MECHANICAL INFORMATION 5 – 6...
Page 22
Dotted line : Pulse 1. A3LCT only : Signal flow 2. Because it is common in A3LCT/A4LCT but the using component is different, the connection, too, is different. : A4LCT only. A4LCT doesn't use drawer connector. MX-LCX5 OVERALL MECHANICAL INFORMATION 5 – 7...
Page 26
LEAD-FREE SOLDER The PWB’s of this model employs lead-free solder. The “LF” marks indicated on the PWB’s and the Service Manual mean “Lead-Free” solder. The alphabet following the LF mark shows the kind of lead-free solder. Example: <Solder composition code of lead-free solder> Solder composition Solder composition code Solder composition...
Page 27
CAUTION FOR BATTERY REPLACEMENT (Danish) ADVARSEL ! Lithiumbatteri – Eksplosionsfare ved fejlagtig håndtering. Udskiftning må kun ske med batteri af samme fabrikat og type. Levér det brugte batteri tilbage til leverandoren. (English) Caution ! Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the manufacturer.
Page 28
Adobe Systems Incorporated. PCL is a registered trademark of the Hewlett-Packard Company. All other trademarks and copyrights are the property of their respective owners. Sharpdesk is a trademark of Sharp Corporation. SHARP CORPORATION Digital Document System Group CS Promotion Center...