Punch Unit (Option) - Sharp MX-FN10 Service Manual

Item Display Item
J STAPLE Staple
PITCH binding
position
adjustment
(Two
positions
pitch)
K PUNCH Punch
CENTER center
adjustment
L PUNCH Punch hole
HOLE position
adjustment
M SADDLE_ Saddle
ADJUST_ alignment
POS position
adjustment
N GRIPPER_ Gripper exit
POS position
adjustment
NOTE: "A: SADDLE POSITION (Saddle binding position adjust-
ment)" and "B: FOLDING POSITION (Saddle folding posi-
tion adjustment)"
The saddle binding position adjustment and the saddle
folding position adjustment can be executed in the system
setting menu. However, the adjustments in the system set-
ting are based on the adjustment value of this simulation.
If, therefore, the adjustment value of this simulation is set
to an extreme level, the adjustment range in the system
setting may be narrowed. (Adjustment range in the system
setting  5.0mm)
If the adjustment range in the system setting is to narrow,
change the adjustment value of this simulation.
In general, when the saddle binding position and the sad-
dle folding positions are adjusted to the center by this simu-
lation, the above trouble will not occur.
Change Change direction
0.2mm Large value: The pitch of
two positions becomes
wider.
Small value: The pitch of
two positions becomes
narrower.
0.2mm Large value: The hole
position is shifted to the
front side from the center.
Small value: The hole
position is shifted to the
rear side from the center.
0.2mm Large value: The distance
between the hole position
and the paper edge
becomes shorter.
Small value: The distance
between the hole position
and the paper edge
becomes longer.
0.2mm Large value: The
alignment plate position is
shifted to the center.
Small value: The
alignment plate position is
shifted to the outside.
0.2mm Large value: The gripper
exit position is shifted to
the front.
Small value: The gripper
exit position is shifted to
the rear.
MX-FN10 ADJUSTMENTS 8 – 2

2. Punch unit (option)

A. Punch unit and punch PWB destination setting
1) When the punch PWB is replaced, the destination must be set
accordingly.
2) Use the DIP switch and the push switch on the punch PWB to
set the destination.
3) The DIP switch setting and destinations are shown in the table
below.
Model Kind of punch
MX-PNX5 (2-hole) 2-hole type
MX-PNX5 (2/3-hole) 2/3-hole type
MX-PNX5 4-hole type
(4-hole France) (France)
MX-PNX5 4-holel type
(4-hole Sweden) (Sweden)
4) Destination setting procedures
a) Check to confirm that the punch unit power is turned OFF.
b) Set the DIP switches 1, 2, and 4 to ON, then push and
hold the push switch and supply the power.
c) Set the DIP switch for a desired destination.
d) Push the push switch to fix the destination setting. (The
LED flashes.)
e) Check to confirm that the LED turns ON (fixed state), and
turn OFF the power of the punch unit.
f) Set all the DIP switches to OFF, and terminate the opera-
tion.
5) Checking the currently set destination
a) Check to confirm that the punch unit power is turned OFF.
b) Set the DIP switches 1, 2, and 4 to ON, then push and
hold the push switch and supply the power.
c) Set the DIP switches 1 and 4 to OFF. (In this case, only
the DIP switch 2 is set to ON.)
d) Push the push switch, and check the number of flashing of
the LED.
(Since the first cycle includes the first lighting of the LED,
count the number of flashing in the second cycle.)
e) Turn OFF the power of the punch unit.
f) Set all the DIP switches to OFF, and terminate the opera-
tion.
DIP switch
1 2 3 4
OFF OFF OFF OFF
OFF OFF OFF ON
OFF OFF ON OFF
OFF OFF ON ON