Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Norac U5
Summary of Contents for Norac U5
- Page 1 Kverneland (Fixed Geometry) Installation Manual RA02...
- Page 2 Reorder P/N: UC5-BC-RA02-INST Rev H (Kverneland Fixed Geometry) NOTICE: NORAC Systems International Inc. reserves the right to improve products and their specifications without notice and without the requirement to update products sold previously. Every effort has been made to ensure the accuracy of the information...
- Page 3 Contents Introduction .....................1 Technical Specifications .................2 General UC5 System Layout .................3 Kit Parts ......................4 Pre-Install Checklist ..................6 Ultrasonic Sensor Installation ...............9 Module Installation ..................12 Software Setup ..................... 13 ...
-
Page 4: Introduction
Introduction Congratulations on your purchase of the NORAC UC5 Spray Height Control System. This system is manufactured with top quality components and is engineered using the latest technology to provide operating reliability unmatched for years to come. When properly used the system can provide protection from sprayer boom damage, improve sprayer efficiency, and ensure chemicals are applied correctly. -
Page 5: Technical Specifications
Technical Specifications CAN ICES-3(A)/NMB-3(A) This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. -
Page 6: General Uc5 System Layout
General UC5 System Layout Figure 1 illustrates the general layout of the UC5 system components: Figure 1: General UC5 System Layout... -
Page 7: Kit Part
Kit Parts Kit Overview Figure 2: RA02 System Parts The use of dielectric grease is not recommended on any NORAC electrical connections. To ensure all stainless steel hardware does not gall or seize apply a light coating of the supplied Permatex Anti-seize grease to all threaded parts upon installation. - Page 8 List of Parts Item Part Number Name Quantity 44706-01 KIT CABLE TIE BLACK 10 PCS 21 IN 150 PCS 7.5 IN 44210-05 CABLE UC5 NETWORK 14 AWG 5M (MOUNTED SPRAYERS) *C01 43210-10 CABLE UC5 NETWORK 14 AWG 10M (TRAILED SPRAYERS) 43210-15 CABLE UC5 NETWORK 18 AWG 15M (BOOMS UP TO 24M) *C05...
-
Page 9: Pre-Install Checklist
Pre-Install Checklist The pre-install checklist is necessary to check the existing sprayer functionality and settings before the installation. 1. Inspect boom suspension wear-pads for excessive wear and ensure the boom rotates freely. 2. Ensure the boom suspension is configured as a short-pendulum (hilly mode). Insert the boom pin to constrain the long-pendulum suspension as shown in Figure 3. - Page 10 4. Adjust the slant speed of the boom until the full stroke of the slant cylinder (not the boom) is 6 seconds (Figure 5). This is the time required for the slant cylinder to travel from fully extended to fully retracted, or vice-versa. 6 Seconds Figure 5: Setting the Slant Speed 5.
- Page 11 Figure 6: Pre-Install Boom Speeds...
-
Page 12: Ultrasonic Sensor Installation
Ultrasonic Sensor Installation Ultrasonic Sensor Serial Number Arrangement When installing the UC5 sensors, start with the smallest serial number on the left-hand side, and proceed to the largest serial number on the right hand side. Each UC5 sensor has a serial number stamped on the sensor housing. - Page 13 Ultrasonic Sensor Mounting Guidelines The following guidelines will ensure optimal sensor performance and prevent sensor measurement error. These rules should be followed for both the wing sensors and the main lift (middle) sensor. 1. In its lowest position, the sensor must be 9 inches (23 cm) or more from the ground (A). 2.
- Page 14 Wing Sensor Installation 1. Install the wing sensors as shown in Figure 9. 2. Typically the best mounting location for the wing sensor brackets will be near just inside the breakaway sections. Figure 9: Wing Sensor Installation A problem can arise if a sensor is not mounted correctly. It is possible for the sensor to read off of the boom instead of the ground.
-
Page 15: Module Installation
Module Installation Control Module An optional module mounting bracket kit is available for purchase from NORAC. Item Part Number Name Quantity 43708 UC5 MOUNTING BRACKET KIT (CONTROL AND INPUT MODULES) 1. Refer to Figure 1 and Figure 10. 2. Securely mount the control module (E01) near the bypass valve on the front right side of the sprayer, near the sprayer CANbus connection, using screws, cable ties or optional brackets. -
Page 16: Software Setup
Software Setup 1. Start up your sprayer and test the sprayer’s functionality. The display terminal does not need to be powered on for the original boom function switches to operate. Unfold the booms and raise/lower each boom and the main section. Confirm that the cabling and hoses are agreeable to the entire range of motion. -
Page 17: Cable Drawings
Cable Drawings ITEM C01: 43210-05 - CABLE UC5 NETWORK 18 AWG - 5M 43210-10 - CABLE UC5 NETWORK 18 AWG - 10M ITEM C05: 43210-15 - CABLE UC5 NETWORK 18 AWG - 15M 43210-20 - CABLE UC5 NETWORK 18 AWG - 20M 43210-25 - CABLE UC5 NETWORK 18 AWG - 25M... - Page 18 ITEM C20: 43240-28 – CABLE UC5 INTERFACE CAN BUS (PIGTAIL)
- Page 19 ITEM C30: 43250-11 - CABLE UC5 BATTERY PIGTAIL...
- Page 20 Canada NORAC Systems International Inc. Phone: (+1) 306 664 6711 Toll Free: 1 800 667 3921 Shipping Address: 3702 Kinnear Place Saskatoon, SK S7P 0A6 United States NORAC, Inc. Phone: (+1) 952 224 4142 Toll Free: 1 866 306 6722...
Need help?
Do you have a question about the U5 and is the answer not in the manual?
Questions and answers