1. Manuals
  2. Brands
  3. Speck pumps Manuals
  4. Swimming Pool Pump
  5. BADU ECOM2/S90
  6. Installation, operating and service manual

Speck pumps BADU ECOM2/S90 Installation, Operating And Service Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Installation, Operating,
and Service Manual
BADU
EcoM2/S90
®
Swimming Pool Pump

Advertisement

Table of Contents
loading

Related Manuals for Speck pumps BADU ECOM2/S90

Summary of Contents for Speck pumps BADU ECOM2/S90

  • Page 1 Installation, Operating, and Service Manual BADU EcoM2/S90 ® Swimming Pool Pump...
  • Page 2 800-223-8538 Phone: 904-739-2626 Fax: 904-737-5261 Website: www.usa.speck-pumps.com Date of Installation: Installed by: Serial Number: For Service Call: Manufactured by Speck Pumps, Jacksonville Florida USA, © 2017 All Rights Reserved. This document is subject to change without notice. Rev. 0317 SW...

  • Page 3: Important Safety Instructions

    OWNER’S MANUAL Swimming Pool Pump READ THIS MANUAL CAREFULLY BEFORE USING THE SPECK PUMP Important Notice: This manual contains important information about the installation, operation and safe use of this product. This information should be given to the owner and/or operator of this equipment. WARNING: This product must be installed and serviced by a qualified pool professional, and must conform to all national, state, and local codes.
  • Page 4 SECTION 1 EQUIPMENT OPERATION AND MAINTENANCE 1/1 LOCATION 5. Before starting the pump for the first time, remove the 1. Locate the pump as close to the pool as practical. Consult see-through lid. (Turn lid ring counterclockwise to remove.) local codes for minimum distance between pool and pump. Fill strainer tank with water until it is level with the suction inlet.
  • Page 5 SECTION 1 EQUIPMENT OPERATION AND MAINTENANCE - Continued 1/3 MAINTENANCE - continued 1/4 WINTERIZING - continued Place a screwdriver, allen wrench or appropriate tool in the CAUTION: Allowing the pump to freeze will cause severe end of the motor shaft and turn it clockwise. OR Remove damage and void the warranty.
  • Page 6 Replacement parts may be available from your installer. When calling the manufacturer regarding a question or Call, fax, or write: Speck Pumps at 8125 Bayberry Road, problem with your pump, please have the serial number available. The serial number is located on the pump either Jacksonville, Florida 32256 Phone (904) 739-2626 Fax on the flange or motor labels.
  • Page 7 2. To the fullest extent permitted by law, the Limited Warranty will be void and of no force or e ect and Speck Pumps - Pool Products, Inc. will have no liability, responsibilities or obligations to Buyer or with respect to the pump and motor in the event...
  • Page 8 32256. Under no condition will products be accepted after the expiration of the Limited Warranty Period. Speck Pumps - Pool Products, Inc. shall not bear any costs or risks incurred by Buyer in shipping a defective pump and motor to Speck Pumps - Pool Products, Inc.
  • Page 9 TWO SPEED POOL MOTOR WITH PROGRAMMABLE CONTROL / TIMER INSTALLATION AND MAINTENANCE MANUAL These instructions cover the motor and the operation of the user interface timer/controller which may be integrated with the motor. Save this instruction manual for future reference.

  • Page 10: Table Of Contents

    IMPorTAnT SAFETy InSTruCTIonS 2EZ Speed Motor Control/Timer Installation Maintenance Manual Save this Instruction Manual for future reference. Table of Contents Motor Control/Timer Specifications ........3 About the 2EZ Speed Motor Control/Timer .

  • Page 11: Motor Control/Timer Specifications

    M017837080000 REV. January 19, 2011 2EZ Speed Motor Control/Timer Speci cations Motor User Interface w/Cover Timer/Control Terminal Cover • Energy Ef cient: Did you know that you can save the The 2EZ Speed motor control is designed to operate from most energy by maximizing your low speed operation, a typical U.S.

  • Page 12: Important Safety Instructions

    M017837080000 REV. January 19, 2011 Important Safety Instructions WARNING This unit should not be serviced in the eld. Do not disassemble or reconnect components in the eld use authori ed factory service only. High voltage and rotating parts can cause serious or fatal in ury.
  • Page 13 M017837080000 REV. January 19, 2011 terminals should be examined carefully for any signs NOTICE Safety glasses should be worn to inspect of physical deterioration or loose fit to the terminals on the equipment while it is running or while a mallet or the motor/control terminal board.

  • Page 14: General Installation Instructions

    M017837080000 REV. January 19, 2011 General Installation Instructions Basic Motor/Timer operation WARNING Follow these instructions to prolong the life of your A properly un tionin motor may swimming pool pump motor/control. e too hot to tou h and ause in ury Be careful when touching the exterior of an operating motor! This condition is normal for most motors when operated at rated load a.

  • Page 15: User Interface Identification

    M017837080000 REV. January 19, 2011 user Interface Identi cation This section describes the motor’s user interface. Program High MEnu run / SToP Set Clock MTuWThFSaSu Set on Time Set off Time override EnTEr Press Enter to Con rm www.nidec-motor.com/Pool HIGH SPEED LoW SPEED o ErrIDE o ErrIDE...
  • Page 16 M017837080000 REV. January 19, 2011 M017837080000 REV. January 19, 2011 user Interface Identi cation user Interface Identi cation This section describes the user interface in detail, including buttons, and LCD data. This section describes the user interface in detail, including buttons, and LCD data. Program Program High...
  • Page 17 M017837080000 REV. January 19, 2011 user Interface Identi cation This section describes the user interface in detail, including buttons, and LCD data. Program High MEnu run / SToP Set Clock MTuWThFSaSu Set on Time Set off Time override EnTEr Press Enter to Con rm www.nidec-motor.com/Pool HIGH SPEED LoW SPEED...

  • Page 18: Quick Start Programming

    M017837080000 REV. January 19, 2011 M017837080000 REV. January 19, 2011 How to Program your 2EZ Speed Control How to Program your 2EZ Speed Control uick Start uick Start A Setting the Clock and Day A Setting the Clock and Day •...

  • Page 19: Detail Programming

    M017837080000 REV. January 19, 2011 How to Program Detail tart i esired Factory Settings B. Set Low Speed on Time (Monday thru Friday) LOW will be flashing, Press ENTER. Set desired Timer is preset with the following factory default settings. “on”...
  • Page 20 M017837080000 REV. January 19, 2011 Functions of The Enter Button: H. Set High Speed on Time (Saturday and Sunday) Press ENTER. Set desired “on” time for motor to 1. Press to activate menu selection. begin running on high speed. Use   keys to navigate through each of the fields.
  • Page 21 M017837080000 REV. January 19, 2011 The second event is a press of the run/SToP button. 1. When the timer has been “enabled”, the RUN/STOP button will be illuminated. Pressing the RUN/STOP button when the timer is “enabled” will disable the timer and the motor will STOP.

  • Page 22: How To Connect

    M017837080000 REV. January 19, 2011 How to Connect Timer Wiring Instructions If AC power is supplied by a GFCI circuit breaker, use a WARNING This unit shall not be serviced in the properly sized dedicated circuit that has no other electrical eld.

  • Page 23: Locking The Keypad

    M017837080000 REV. January 19, 2011 Locking The eypad not run when the filtration pump is off. The pool heater program timer should be set to start and stop during the To prevent undesired changes to your programming, programmed on and off times programmed on your 2EZ a keypad lockout feature is included.

  • Page 24: General Troubleshooting

    M017837080000 REV. January 19, 2011 General Troubleshooting This chart suggests common answers to electric motor and control/timer issues. Refer to your pump manual for hydraulic guidance. When repetitive issues occur, Nidec recommends contacting your local pool and spa professional for technical assistance. Symptom Possible Causes Corrective Action...

  • Page 25: Recommended Maintenance

    M017837080000 REV. January 19, 2011 recommended Maintenance Certain repairs or services are the responsibility of the Purchaser and the Purchaser is expected to WARNING Always disconnect electrical power pay for them. This warranty does not extend to any at the fuse box or circuit breaker before handling losses or damages due to misuse, accident, abuse, electrical connections or performing maintenance neglect, negligence, unauthorized modification or...
  • Page 26 Nidec Motor Corporation 8050 W. Florissant Avenue St. Louis, MO 63136 www.nidec-motor.com/pool Pool Motor Product Service Hotline: 1-800-566-1418...

Table of Contents