GE G60 Instruction Manual page 592

TRANSDUCER INPUTS/OUTPUTS
5.10.3.2 Remote RTDs 1 through 12
SETTINGS  TRANSDUCER I/O  RRTD INPUTS  RRTD RTD 1(12)
 RRTD 1

5
The remote RTD inputs convert values of input resistance into temperature for further operations. These inputs are
intended to be connected to any of the RTD types in common use. Hardware details are contained in chapter 3.
On power up, the G60 reads and saves all application and type settings from the RRTD. This synchronizes the RRTD and
G60. Any changes to RRTD settings (function, application, or type) from the G60 interface are immediately reflected in the
RRTD. The following rules are followed:
• If the
RRTD 1 FUNCTION
• If the
RRTD 1 FUNCTION
• If the
RRTD 1 APPLICATION
device
• If the
RRTD 1 APPLICATION
An RRTD actual value of –43°C implies that the
setting is "None."
APPLICATION
If the RRTD communication link with the G60 is broken, then the last temperature actual values are retained until the RRTD
communication failure is detected. When this occurs, a RRTD COMM FAILURE self-test alarm and target message is
generated, an event is logged in the event recorder, and the temperature actual values are reset to 0. When the link is re-
established, the
RRTD 1 APPLICATION
— This setting enables and disables the remote RTD. When disabled, no actual value is created for the
RRTD 1 FUNCTION
remote RTD.
5-378
RRTD 1 FUNCTION:

Disabled
RRTD 1 ID:

RRTD 1
RRTD 1 TYPE:

100 Ω Platinum
RRTD 1

APPLICATION: None
RRTD 1 ALARM

TEMPERATURE: 130°C
RRTD 1 ALARM

PKP DELAY: 5 s
RRTD 1 TRIP

TEMPERATURE: 130°C
RRTD 1 TRIP

PKP DELAY: 5 s
RRTD 1 TRIP

RST DELAY: 5 s
RRTD 1 TRIP VOTING:

None
RRTD 1 OPEN:

None
RRTD 1 BLOCK:

Off
RRTD 1 TARGET:

Self-reset
RRTD 1 EVENTS:

Disabled
setting is "Enabled," then the
setting is "Disabled," then
RRTD1 APPLICATION
or settings are changed, then these settings are immediately written to the RRTD
RRTD 1 TYPE
setting is "Group 1" or "Group 2," then a value of "Other" is written to the RRTD device
RRTD 1 FUNCTION
and settings are read from the RRTD to re-synchronize the device.
RRTD 1 TYPE
Range: Disabled, Enabled
Range: Up to 20 alphanumeric characters
Range: 100 Ω Nickel, 10 Ω Copper, 100 Ω Platinum,
120 Ω Nickel
Range: None, Stator, Bearing, Ambient, Group 1,
Group 2
Range: 1 to 200°C in steps of 1
Range: 5 to 600 s in steps of 5
Range: 1 to 200°C in steps of 1
Range: 5 to 600 s in steps of 5
Range: 5 to 600 s in steps of 5
Range: None, Group, Remote RTD 1, Remote RTD 2,...,
Remote RTD 12
Range: None, Alarm, Block
Range: FlexLogic operand
Range: Self-reset, Latched, Disabled
Range: Disabled, Enabled
setting value is written to RRTD device
RRTD 1 APPLICATION
setting value is set as "None"
setting is "Enabled" but the corresponding
G60 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL
CHAPTER 5: SETTINGS
RRTD 1