Page 1 Liberty 2 0 0 8 O W N E R ’ S M A N U A L...
Page 2: Introduction
TABLE OF CONTENTS SECTION PAGE ............. 3 INTRODUCTION .
Page 4: Table Of Contents
INTRODUCTION CONTENTS Introduction ......4 Warnings And Cautions ....7 Rollover Warning .
Page 5: Introduction
4 INTRODUCTION INTRODUCTION ROLLOVER WARNING This Owner’s Manual has been prepared with the assis- Utility vehicles have a significantly higher rollover rate tance of service and engineering specialists to acquaint than other types of vehicles. This vehicle has a higher you with the operation and maintenance of your vehicle.
Page 6: How To Use This Manual
INTRODUCTION 5 belts could cut the highway death toll by 10,000 or more each year and could reduce disabling injuries by two million annually. In a rollover crash, an unbelted person is significantly more likely to die than a person wearing a seat belt.
Page 7 6 INTRODUCTION...
Page 8: Warnings And Cautions
INTRODUCTION 7 WARNINGS AND CAUTIONS This Owners Manual contains WARNINGS against op- erating procedures that could result in an accident or bodily injury. It also contains CAUTIONS against proce- dures that could result in damage to your vehicle. If you do not read this entire Owners Manual, you may miss important information.
Page 9: Vehicle Modifications/Alterations
8 INTRODUCTION VEHICLE MODIFICATIONS/ALTERATIONS WARNING! Any modifications or alterations to this vehicle could seriously affect its roadworthiness and safety and may lead to an accident resulting in serious injury or death.
Page 10 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE CONTENTS ▫ To Release The Steering Wheel Lock ..18 A Word About Your Keys ....12 ▫...
Page 11 10 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE ▫ To Unlatch The Liftgate Flip-Up Window ..24 ▫ Wind Buffeting ......39 ▫...
Page 12 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 11 ▫ Child Restraint ......70 ▫ Exhaust Gas ......81 ▫...
Page 13: A Word About Your Keys
12 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE A WORD ABOUT YOUR KEYS numbers can be used to order duplicate keys from your You can insert the double-sided keys into the locks with authorized dealer. Ask your authorized dealer for these either side up.
Page 14 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 13 Information Center (EVIC), features such as the power window switches, radio, power sunroof or Sky Slider (if equipped), and power outlets will remain active for 45 seconds after the ignition switch is turned to the LOCK position.
Page 15: Key-In-Ignition Reminder
14 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Key-In-Ignition Reminder WARNING! If you open the driver’s door and the key is in the ignition, a chime will sound to remind you to remove the Never leave children alone in a vehicle. Leaving key.
Page 16 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 15 the vehicle. The system will shut the engine off in two longer than 10 seconds), it indicates that there is a fault in seconds if someone uses an invalid key to try to start the the electronics.
Page 17: Replacement Keys
16 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Replacement Keys procedure. This procedure consists of programming a blank key to the vehicle electronics. A blank key is one NOTE: Only keys that are programmed to the vehicle that has never been programmed. electronics can be used to start and operate the vehicle.
Page 18: General Information
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 17 3. Insert the second valid key into the ignition switch. Repeat this procedure to program up to eight keys. If you Turn the ignition switch to the ON position within 15 do not have a programmed Sentry Key , contact your seconds.
Page 19: Steering Wheel Lock - If Equipped
18 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • This device must accept any interference that may be To Release the Steering Wheel Lock received, including interference that may cause undes- Insert the key in the ignition and turn the wheel slightly ired operation.
Page 20: Rearming Of The System
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 19 NOTE: The PANIC and Security Alarms are quite NOTE: The system will not arm if you lock the doors different. Please take a moment to activate the PANIC with the manual door lock plungers or the driver’s door and the Security modes to hear the differences in the lock cylinder.
Page 21: To Disarm The System
20 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE To Disarm the System: Tamper Alert Either press the UNLOCK button on the RKE transmitter If something has triggered the alarm in your absence, the or insert a valid Sentry Key into the ignition lock horn will sound three times when you unlock the doors.
Page 22: Remote Keyless Entry (Rke)
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 21 NOTE: • The Illuminated Entry system will not operate the interior lights if the dimmer control is in the extreme downward position. REMOTE KEYLESS ENTRY (RKE) This system allows you to lock or unlock the doors and liftgate, open the liftgate flip-up window, or activate the PANIC alarm from distances up to 23 ft (7 m) using a hand-held Remote Keyless Entry (RKE) transmitter.
Page 23 22 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Remote Key Unlock, Driver Door/All Doors First 3. Test the feature from outside the vehicle by pressing This feature lets you program the system to unlock either the LOCK and UNLOCK buttons on the RKE transmitter. the driver’s door or all doors and the liftgate on the first 4.
Page 24: To Lock The Doors And Liftgate
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 23 1. Press the LOCK button on a programmed (i.e., func- To Lock the Doors and Liftgate: Press and release the LOCK button on the RKE transmit- tional) RKE transmitter for at least 4 seconds, but no ter to lock all doors and the liftgate.
Page 25: To Unlatch The Liftgate Flip-Up Window
24 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Flash Lights with Lock 3. Test the feature from outside the vehicle by pressing The feature will cause the turn signal lights to flash when the LOCK and UNLOCK buttons on the RKE transmitter. the doors are locked or unlocked with the RKE transmit- 4.
Page 26: Using The Panic Alarm
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 25 During the PANIC Mode, the door locks and Remote Using the PANIC Alarm Keyless Entry (RKE) system will function normally. NOTE: The PANIC and Security Alarms are quite PANIC mode will not disarm the Security System on different.
Page 27 26 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • Do not touch the battery terminals that are on the back housing or the printed circuit board. 1. Remove the screw from the RKE transmitter case (if equipped). 2. With the RKE transmitter buttons facing down, use a flat blade tool to pry the two halves of the RKE transmit- ter case apart.
Page 28: General Information
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 27 5. Reinstall and tighten the screw until snug (if 1. Weak batteries in RKE transmitter. The expected life of equipped). the batteries is from one to two years. General Information 2. Closeness to a radio transmitter such as a radio station This device complies with Part 15 of FCC rules and with tower, airport transmitter, and some mobile or CB radios.
Page 29: How To Use Remote Start
28 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE How To Use Remote Start All of the following conditions must be met before the engine will remote start: • Shift lever in PARK. • Doors closed. • Hood closed. • Liftgate closed. •...
Page 30 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 29 To Enter Remote Start Mode To Exit Remote Start Mode and Drive the Vehicle Press and release the REMOTE START button Before the end of the 15-minute cycle, press and release on the RKE transmitter twice. The engine will the UNLOCK button on the RKE transmitter to unlock start and the vehicle will remain in the Remote the doors and disarm the Vehicle Security Alarm (if...
Page 31: Door Locks
30 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE DOOR LOCKS If the door lock plunger is down when you shut the door, the door will lock. Therefore, make sure the keys are not Manual Door Locks inside the vehicle before closing the door. To lock each door, push the door lock plunger on each door trim panel downward.
Page 32: Power Door Locks
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 31 Power Door Locks WARNING! A power door lock switch is located on each of the front door trim panels. Use this switch to lock or unlock the • For personal security and safety in the event of an doors and liftgate.
Page 33 32 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE locks will not operate. This prevents you from acciden- Automatic Door Locks Programming tally locking your keys in the vehicle. Removing the key The Automatic Door Locks feature can be enabled or or closing the door will allow the locks to operate.
Page 34 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 33 4. A single chime will indicate the completion of the 5. The doors were not previously unlocked. programming. 6. The vehicle speed is 0 mph (0 km/h). 5. Repeat these steps if you want to return this feature to Automatic Unlock Doors on Exit Programming its previous setting.
Page 35: Child-Protection Door Lock System (Rear Doors)
34 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 3. Depress the power door UNLOCK switch to unlock the doors. 4. A single chime will indicate the completion of the programming. Repeat these steps if you want to return this feature to its previous setting.
Page 36 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 35 2. Insert the tip of the ignition key into the child lock WARNING! control and rotate it to the UNLOCK position. Avoid trapping anyone in a vehicle in a collision. Remember that the rear doors can only be opened from the outside when the child protection locks are engaged.
Page 37: Windows
36 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WINDOWS There are single window controls on each passenger door trim panel, which operate the passenger door windows. Power Windows The window controls will operate when the ignition The window controls on the driver’s door trim panel switch is in the ON or ACC position.
Page 38 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 37 To open the window part way, press the window switch Auto Up Feature with Anti-Pinch Protection — If to the first detent and release it when you want the Equipped window to stop. On some models, the driver’s power window switch has an Auto Up feature.
Page 39 38 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE For vehicles equipped with the EVIC, the power window WARNING! switches will remain active for up to 10 minutes after the ignition switch is turned to the LOCK position. Opening There is no anti-pinch protection when the window either front door will cancel this feature.
Page 40: Wind Buffeting
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 39 1. Pull the window switch up to close window com- pletely and continue to hold the switch up for an additional two seconds after the window is closed. 2. Push the window switch down firmly to the second detent to open the window completely and continue to hold the switch down for an additional two seconds after the window is fully open.
Page 41: Liftgate
40 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Slider open, adjust the sunroof or Sky Slider opening door trim panel or the Remote Keyless Entry (RKE) to minimize the buffeting or open any window. transmitter to lock and unlock the liftgate. The manual door locks on the doors and the driver’s door lock LIFTGATE cylinder will not lock and unlock the liftgate.
Page 42: Lap/Shoulder Belts
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 41 adult-size belts, your seat belts also can be used to hold and cause a collision that includes you. This can happen infant and child restraint systems. far away from home or on your own street. Please pay close attention to the information in this Research has shown that seat belts save lives, and they section.
Page 43 42 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! Lap/Shoulder Belt Operating Instructions • It is extremely dangerous to ride in a cargo area, 1. Enter the vehicle and close the door. Sit back and inside or outside of a vehicle. In a collision, people adjust the seat.
Page 44 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 43 Latch Plate Latch Plate To Buckle 3. When the belt is long enough to fit, insert the latch plate into the buckle until you hear a “click.”...
Page 45 44 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! 4. Position the lap belt across your thighs, below your • A belt that is buckled into the wrong buckle will abdomen. To remove slack in the lap belt portion, pull up not protect you properly.
Page 46 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 45 WARNING! • A lap belt worn too high can increase the risk of injury in a collision. The belt forces won’t be at the strong hip and pelvic bones, but across your abdo- men.
Page 47 46 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! A frayed or torn belt could rip apart in a collision and leave you with no protection. Inspect the belt system periodically, checking for cuts, frays, or loose parts. Damaged parts must be replaced immediately. Do not disassemble or modify the system.
Page 48: Lap/Shoulder Belt Untwisting Procedure
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 47 Lap/Shoulder Belt Untwisting Procedure Seat Belt Pretensioners Use the following procedure to untwist a twisted lap/ The driver and front passenger seat belts are equipped shoulder belt. with pretensioning devices that are designed to remove any slack from the seat belt systems in the event of a 1.
Page 49: Enhanced Seat Belt Use Reminder System (Beltalert )
48 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Enhanced Seat Belt Use Reminder System BeltAlert Programming The Enhanced Warning System (BeltAlert ) can be en- (BeltAlert ) If the driver’s or front passenger’s seat belt has not been abled or disabled by your authorized dealer or by buckled within 60 seconds of starting the vehicle, and if performing the following steps: the vehicle speed is greater than 5 mph (8 km/h), the...
Page 50: Automatic Locking Mode - If Equipped
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 49 3. Within 60 seconds of turning the ignition switch to the Automatic Locking Mode — If Equipped ON position, unbuckle and then re-buckle the driver’s In this mode, the shoulder belt is automatically pre- seat belt at least three times within 10 seconds, ending locked.
Page 51: Energy Management Feature
50 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE How to Disengage The Automatic Locking Mode WARNING! Disconnect the combination lap/shoulder belt from the buckle and allow it to retract completely to disengage the • The belt and retractor assembly must be replaced Automatic Locking mode and activate the vehicle sensi- if the seat belt assembly “automatic locking retrac- tive (emergency) locking mode.
Page 52: Seat Belt Extender
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 51 Keep the belt low so that it does not come across the WARNING! abdomen. That way the strong bones of the hips will take the force if there is a collision. Using a seat belt extender when not needed can increase the risk of injury in a collision.
Page 53 52 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE The front passenger airbag is also certified to the Federal regulations that define Occupant Classification (refer to information on Occupant Classification System in this section). This vehicle is equipped with side curtain airbags to protect the driver and the front and rear passengers sitting next to a window.
Page 54 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 53 Window Airbag Location NOTE: Airbag covers may not be obvious in the interior trim; but they will open to allow airbag deployment.
Page 55 54 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! Along with the seat belts, the front airbags provide • Do not put anything on or around the front and improved protection for the driver and front passenger. side curtain airbag covers or attempt to manually Side Curtain Airbags also work with seat belts to im- open them.
Page 56 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 55 Occupant Classification System has determined the pas- restraints or belt-positioning booster seats. Older chil- senger seat is empty or is occupied by someone that is dren who do not use child restraints or belt-positioning classified in a category other than that of an adult (refer booster seats should ride properly buckled up in the rear to information on Occupant Classification System in this...
Page 57 56 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 4. Do not lean against the door or window, airbags will WARNING! inflate forcefully into the space between you and the door. • Relying on the airbags alone could lead to more severe injuries in a collision.
Page 58 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 57 • Front Passenger Seat Track Position Sensors Airbag System Components The airbag system consists of the following: • Occupant Classification System (OCS) — Front Pas- • Occupant Restraint Controller (ORC) senger Seat Only •...
Page 59 58 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE The ORC also monitors the readiness of the electronic Warning Light” either momentarily or continuously. A parts of the system whenever the ignition switch is in single chime will sound if the light comes on again the START or ON position.
Page 60 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 59 NOTE: Children 12 years and younger should always ride buckled up in a rear seat in an appropriate child restraint. • The Passenger Airbag Disable (PAD) Indicator Light (an amber light located in the center of the instrument panel) tells the driver and front passenger when the front passenger airbag is turned off.
Page 61 60 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE is turned off and it will not inflate. If the “PAD Grocery Bags, Indicator Light” is not illuminated, DO NOT assume Heavy Brief- the airbag is turned off and move the child restraint to cases, and Other the rear seat.
Page 62 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 61 properly classified. Reclining the seat back too far may seat is removed (or even if the seat attachment bolts are change how an occupant is classified by the OCS. loosened or tightened in any way), take the vehicle to an authorized dealer.
Page 63 62 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • The Driver and Passenger Airbag/Inflator Units are • The Occupant Classification Module (OCM) is lo- located in the center of the steering wheel and the cated beneath the front passenger seat. The OCM passenger side of the instrument panel.
Page 64 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 63 sides of the vehicle for a rollover event. A quantity of (OCS) to properly classify the front passenger and calcu- nontoxic gas is generated to inflate the side curtain late the proper airbag deployment. Do not make any airbag.
Page 65 64 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: A collision that is not severe enough to need WARNING! airbag protection will not activate the system. This does not mean something is wrong with the airbag system. Unapproved modifications or service procedures to the front passenger seat assembly or its related com- If you do have a collision which deploys the airbags, any ponents may inadvertently change the airbag deploy-...
Page 66 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 65 inflation. These airborne particles may irritate the skin, WARNING! eyes, nose, or throat. If you have skin or eye irritation, rinse the area with cool water. For nose or throat Deployed airbags and seat belt pretensioners cannot irritation, move to fresh air.
Page 67 66 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • Turns on the interior lights, which remain on as long as the battery has power or until the ignition key is removed. • Unlocks the doors automatically. NOTE: The interior lights can only be deactivated if the key is removed from the ignition switch or the vehicle is driven.
Page 68 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 67 Maintaining Your Airbag System Airbag Warning Light WARNING! You will want to have the airbag system ready to inflate for your protection in an impact. The airbag system is • Modifications to any part of the airbag system designed to be maintenance free.
Page 69 68 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Event Data Recorder (EDR) used by DaimlerChrysler Corporation and others to learn In the event of an accident, your vehicle is designed to more about the possible causes of crashes and associated record up to five seconds of specific vehicle data param- injuries in order to assess and improve vehicle perfor- eters in an EDR.
Page 70 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 69 • Diagnostic trouble code(s) and warning light status for may be released for incorporation in aggregate crash databases, such as those maintained by the U.S. govern- electronically controlled safety systems, including the ment and various states.
Page 71: Child Restraint
70 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • Traction/stability control status WARNING! • Tire pressure monitoring system status In a collision, an unrestrained child, even a tiny baby, Child Restraint can become a missile inside the vehicle. The force Everyone in your vehicle needs to be buckled up all the required to hold even an infant on your lap can time —...
Page 72 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 71 Infants and Child Restraints “LATCH — Child Seat Anchorage System (Lower Anchors and Tether for CHildren)” in this section. • Safety experts recommend that children ride • Rearward-facing child seats must NEVER be used in rearward-facing in the vehicle until they are at least one year old and weigh at least 20 lbs (9 kg).
Page 73 72 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • Check belt fit periodically. A child’s squirming or The belt-positioning booster seat is for children weighing more than 40 lbs (18 kg), but who are still too small to fit slouching can move the belt out of position. the vehicle’s seat belts properly.
Page 74 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 73 Standards. The manufacturer also recommends that WARNING! you try a child restraint in the vehicle seats where you will use it before you buy it. • Improper installation can lead to failure of an infant or child restraint.
Page 75 74 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE LATCH — Child Seat Anchorage System (Lower kits or retrofit kits. You are urged to take advantage of all the available attachments provided with your child re- Anchors and Tether for CHildren) Your vehicle’s rear seat is equipped with the child straint in any vehicle.
Page 76 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 75 LATCH-Compatible Child Restraint System” and “In- stalling Child Restraints Using the Vehicle Seat Belt” in this section for typical installation instructions. Installing the LATCH-Compatible Child Restraint System We urge that you carefully follow the directions of the manufacturer when installing your child restraint.
Page 77 76 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE hook for attachment to the tether strap anchorage and a means of adjusting the tension of the strap. You will first loosen the adjusters on the lower straps and on the tether strap so that you can more easily attach the hooks or connectors to the vehicle anchorages.
Page 78 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 77 belt. However, any seat belt system may loosen with WARNING! time, so check the belt occasionally, and pull it tight if necessary. Improper installation of a child restraint to the LATCH anchorages can lead to failure of an infant or If the seat belt has an automatic locking retractor, pull the child restraint.
Page 79 78 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE If the belt still can’t be tightened, or if by pulling and pushing on the restraint loosens the belt, you may need to do something more. Disconnect the latch plate from the buckle, turn the buckle around, and insert the latch plate into the buckle again.
Page 80: Engine Break-In Recommendations
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 79 ENGINE BREAK-IN RECOMMENDATIONS WARNING! A long break-in period is not required for the engine in your vehicle. An incorrectly anchored tether strap could lead to increased head motion and possible injury to the Drive moderately during the first 300 mi (500 km).
Page 81: Safety Tips
80 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE A new engine may consume some oil during its first few WARNING! thousand miles (kilometers) of operation. This should be considered as a normal part of the break-in and not It is extremely dangerous to ride in a cargo area, interpreted as an indication of difficulty.
Page 82: Exhaust Gas
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 81 If you are required to drive with the liftgate open, make Exhaust Gas sure that all windows are closed, and the BLOWER WARNING! switch on the climate control is set at high speed. DO NOT use the recirculation mode.
Page 83: The Vehicle
82 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Safety Checks You Should Make Inside The authorized dealer. If the light stays on, flickers, or comes on while driving, have the system checked by an autho- Vehicle rized dealer. Seat Belts Inspect the seat belt system periodically, checking for Defroster cuts, frays, and loose parts.
Page 84 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 83 Lights Have someone observe the operation of exterior lights while you work the controls. Check turn signal and high beam indicator lights on the instrument panel. Door Latches Check for positive closing, latching, and locking. Fluid Leaks Check area under vehicle after overnight parking for fuel, engine coolant, oil, or other fluid leaks.
Page 86 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CONTENTS Mirrors .......90 Hands-Free Communication (UConnect ) — If Equipped .
Page 87 86 UNDERSTANDING THE FEATURES OF YOUR VEHICLE ▫ Voice Recognition System (VR) Operation ..121 ▫ Memory Position Recall ....137 ▫...
Page 88 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 87 ▫ Turn Signals ......144 Electronic Speed Control — If Equipped ..154 ▫...
Page 89 88 UNDERSTANDING THE FEATURES OF YOUR VEHICLE ▫ Programming HomeLink ▫ Sunshade Operation ....171 ....164 ▫...
Page 90 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 89 ▫ Electrical Outlet Use With Engine Off ..179 Cargo Area Features ..... 183 ▫...
Page 91: Mirrors
90 UNDERSTANDING THE FEATURES OF YOUR VEHICLE MIRRORS Annoying headlight glare can be reduced by moving the small control under the mirror to the night position Inside Day/Night Mirror (toward the rear of vehicle). The mirror should be ad- Adjust the mirror to center on the view through the rear justed while set in the day position (toward the wind- window.
Page 92: Outside Mirrors
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 91 Outside Mirrors To receive maximum benefit, adjust the outside mirror(s) to center on the adjacent lane of traffic and a slight overlap of the view obtained from the inside mirror. NOTE: The passenger side convex outside mirror will give a much wider view to the rear, and especially of the lane next to your vehicle.
Page 93: Exterior Mirrors Folding Feature - If Equipped
92 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Exterior Mirrors Folding Feature — If Equipped Some models have exterior mirrors that are hinged. The hinge allows the mirror to pivot forward and rearward to resist damage. The hinge has three detent positions: forward, rearward, and normal.
Page 94: Heated Remote Control Mirrors - If Equipped
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 93 Models with Express Window Feature Illuminated Vanity Mirrors — If Equipped Press and release the mirror SELECT button marked L or An illuminated vanity mirror is on each sun visor. To use R and then press one of the four arrow buttons to move the mirror, rotate the sun visor down and swing the the mirror in the direction the arrow is pointing.
Page 95: Hands-Free Communication (Uconnect ) - If Equipped
Hands-Free Communication (UConnect ) sys- tem. Refer to your “Navigation User’s Manual” for • www.dodge.com/uconnect UConnect system operating instructions for this radio. • www.jeep.com/uconnect UConnect is a voice-activated, hands-free, in-vehicle • or call 1–877–855–8400 communications system. UConnect allows you to dial a...
Page 96 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 95 UConnect allows you to transfer calls between the system at a time. The system is available in English, system and your cellular phone as you enter or exit your Spanish, or French languages (as equipped). vehicle and enables you to mute the system’s microphone Phone Button for private conversation.
Page 97: Operation
96 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • Prior to giving a voice command, one must wait for Profile) you may not be able to use any UConnect features. Refer to your cellular service provider or the the beep, which follows the Ready prompt or another phone manufacturer for details.
Page 98 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 97 Voice Command Tree Pair (Link) UConnect System to a Cellular Phone Refer to “Voice Tree” in this section. To begin using your UConnect system, you must pair your compatible Bluetooth enabled cellular phone. Help Command If you need assistance at any prompt, or if you want to To complete the pairing process, you will need to refer-...
Page 99 98 UNDERSTANDING THE FEATURES OF YOUR VEHICLE enter into your cellular phone. You can enter any make a call. You can select to use a lower priority four-digit PIN. You will not need to remember this PIN cellular phone at any time (refer to Advanced Phone after the initial pairing process.
Page 100 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 99 • The UConnect system will confirm the phone num- • The UConnect system will confirm the name and ber and then dial. The number will appear in the then dial the corresponding phone number, which display of certain radios.
Page 101 100 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • When prompted, enter the number designation (e.g., Phonebook Download Home, Work, Mobile, or Pager ). This will allow UConnect allows the user to download entries from you to store multiple numbers for each phonebook their phone via Bluetooth .
Page 102 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 101 • When prompted, recite the new phone number for the the UConnect system, and then send the address book entry via Bluetooth . Please see your phone phonebook entry that you are editing. Owner’s Manual for specific instructions on how to After you are finished editing an entry in the phonebook, drop the Bluetooth connection.
Page 103 102 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • After the Ready prompt and the following beep, say Delete All Entries in the UConnect Phonebook Phonebook Delete. • Press the PHONE button to begin. • After you enter the Phonebook Delete menu, you will •...
Page 104: Phone Call Features
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 103 • The UConnect system will play the names of all the accessed through the UConnect system. Check with phonebook entries. your cellular service provider for the features that you have. • To call one of the names in the list, press the “Voice Recognition”...
Page 105 104 UNDERSTANDING THE FEATURES OF YOUR VEHICLE call waiting that you normally hear when using your cell Place/Retrieve a Call From Hold phone. Press the PHONE button to place the current call To put a call on hold, press the PHONE button until you on hold and answer the incoming call.
Page 106 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 105 • After the Ready prompt and the following beep, say Three-Way Calling To initiate three-way calling, press the “Voice Recogni- Redial. tion” button while a call is in progress, and make a • The UConnect system will call the last number that second phone call, as described under Making a Second was dialed from your cellular phone.
Page 107: Uconnect System Features
106 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • After the ignition key is switched to OFF, a call can After selecting one of the languages, all prompts and continue on the UConnect system for a certain dura- voice commands will be in that language. tion, after which the call is automatically transferred NOTE: After every UConnect language change opera- from the UConnect system to the mobile phone.
Page 108 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 107 • After the Ready prompt and the following beep, say Towing Assistance Emergency and the UConnect system will instruct If you need towing assistance: the paired cellular phone to call the emergency num- •...
Page 109 108 UNDERSTANDING THE FEATURES OF YOUR VEHICLE certain companies, which time out a little too soon to sequence on your cellular phone keypad, you can press work properly with the UConnect system. the “Voice Recognition” button and say the sequence you wish to enter, followed by the word Send.
Page 110 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 109 • Press the PHONE button to begin. NOTE: • You may not hear all of the tones due to cellular phone • After the Ready prompt and the following beep, say network configurations; this is normal. Setup Confirmations.
Page 111: Advanced Phone Connectivity
110 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • Following the beep, say Mute. dialing a number with your paired Bluetooth cellular phone, the audio will be played through your vehicle’s In order to un-mute the UConnect system: audio system. The UConnect system will work the same •...
Page 112 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 111 Connect or Disconnect Link Between the the lowest priority. To “select” or “delete” a paired UConnect System and Cellular Phone phone being announced, press the “Voice Recogni- Your cellular phone can be paired with many different tion”...
Page 113: Things You Should Know About Your Uconnect System
112 UNDERSTANDING THE FEATURES OF YOUR VEHICLE UConnect system will return to using the highest Things You Should Know About Your UConnect priority phone present in or near (approximately System within 30 ft [9 m]) the vehicle. UConnect Tutorial To hear a brief tutorial of the system features, press the Delete UConnect Paired Cellular Phones PHONE button and say “UConnect Tutorial.”...
Page 114 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 113 • Speak normally, without pausing, just as you would Repeat the words and phrases when prompted by the UConnect system. For best results, the Voice Training speak to a person sitting a few feet/meters away from session should be completed when the vehicle is parked you.
Page 115 114 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • When navigating through an automated system such • In a convertible vehicle, system performance may be as voice mail, or when sending a page, at the end of compromised with the convertible top down. speaking the digit string, make sure to say Send.
Page 116 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 115 • Echo at the far end can sometimes be reduced by Power-Up lowering the in-vehicle audio volume. After switching the ignition key from OFF to either ON or ACC position, or after a language change, you must •...
Page 117 116 UNDERSTANDING THE FEATURES OF YOUR VEHICLE...
Page 118 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 117...
Page 119 118 UNDERSTANDING THE FEATURES OF YOUR VEHICLE...
Page 120 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 119 Voice Commands Voice Commands Primary Alternate(s) Primary Alternate(s) zero call cancel confirmation prompts three continue four delete five dial download seven edit eight emergency nine English star (*) erase all plus (+) Espanol pound (#) Francais add location...
Page 121 120 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Voice Commands Voice Commands Primary Alternate(s) Primary Alternate(s) language return to main menu return or main menu list names select phone select list phones send mobile set up phone settings or phone set up mute towing assistance mute off...
Page 122: General Information
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 121 possible. The ability of the Voice Interface System to General Information This device complies with Part 15 of the FCC rules and recognize user voice commands may be negatively af- RSS 210 of Industry Canada. Operation is subject to the fected by rapid speaking or a raised voice level.
Page 123: Commands
122 UNDERSTANDING THE FEATURES OF YOUR VEHICLE If you ever wish to interrupt the system while it lists The system will best recognize your speech if the win- options, press the VR hard-key, listen for the beep, and dows are closed, and the heater/air-conditioning fan is say your command.
Page 124 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 123 • NEXT STATION (to select the next station) 3. Use the ON/OFF VOLUME rotary knob to adjust the volume to a comfortable level while the voice recognition • PREVIOUS STATION (to select the previous station) system is speaking.
Page 125 124 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Satellite Radio Disc To switch to satellite radio mode say SAT or SATELLITE To switch to the disc mode say DISC. In this mode, you RADIO. In this mode, you may say the following com- may say the following commands: mands: •...
Page 126: Voice Training
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 125 − CONTINUE (to continue recording) Voice Training For users experiencing difficulty with the system recog- − DELETE (to delete the recording) nizing their voice commands or numbers, the UConnect • PLAY MEMOS (to play previously recorded memos) system Voice Training feature may be used.
Page 127: Seats
126 UNDERSTANDING THE FEATURES OF YOUR VEHICLE SEATS Manual Front Seat Adjustments Forward and Rearward Adjustment — If Equipped The manual seat adjustment bar is at the front of the seat, near the floor. Pull the bar upward to move the seat forward or rearward.
Page 128 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 127 WARNING! Adjusting a seat while the vehicle is moving is dangerous. The sudden movement of the seat could cause you to lose control. The seat belt might not be properly adjusted and you could be injured. Adjust any seat only while the vehicle is parked.
Page 129 128 UNDERSTANDING THE FEATURES OF YOUR VEHICLE inboard side of the seat. Turn the control lever downward WARNING! to increase and upward to decrease the desired amount of lumbar support. • Adjusting a seat while the vehicle is moving is dangerous.
Page 130: Power Seat - If Equipped
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 129 forward, rearward, or to tilt the seat. For vehicles equipped with a power passenger seat, use this switch to move the seat forward and rearward. Fold Flat Passenger Seat Power Seat — If Equipped The power seat switch is on the outboard side of the seat Power Seat Switch near the floor.
Page 131: Head Restraints
130 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Head Restraints CAUTION! Head restraints can reduce the risk of whiplash injury in the event of impact from the rear. Adjust the head Do not place any article under any seat as it may restraints so that the upper edge is as high as practical.
Page 132: Heated Seats - If Equipped
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 131 The controls for each heater are located near the bottom center of the instrument panel. After turning the ignition ON, you can choose from HIGH, LOW, or OFF heat settings. Amber indicator lights in each switch indicate the level of heat in use.
Page 133: 60/40 Split Folding Rear Seat With Fold Flat Feature
132 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Press the switch once to select HIGH-level heating. Press WARNING! the switch a second time to select LOW-level heating. Press the switch a third time to shut OFF the heating Persons who are unable to feel pain to the skin elements.
Page 134 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 133 NOTE: Prior to folding the rear seat, it may be necessary To Lower the Rear Seat to position the front seat to its mid-track position. Also, 1. Locate the release strap on the lower outboard side of be sure that the front seats are fully upright and posi- each rear seatback.
Page 135 134 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 4. If desired, push down on the seatback to lock it in the folded position. Recliner Adjustment To Raise the Rear Seat The rear seatback also reclines for additional passenger comfort. Pull the release strap while sitting in the rear NOTE: If interference from the cargo area prevents the seat to recline the seatback.
Page 136: Driver Memory Seat - If Equipped
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 135 1. Turn the ignition ON. DRIVER MEMORY SEAT — IF EQUIPPED This feature allows the driver to store up to two different 2. Adjust all memory profile settings to desired prefer- memory profiles, for easy recall through a memory ences (i.e., seat, side mirror, and radio station presets).
Page 137: Linking And Unlinking The Remote Keyless Entry
136 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 3. Press and release the SET (S) button on the memory Linking and Unlinking the Remote Keyless Entry switch, then press the side of the rocker switch labeled (2) (RKE) Transmitter to the Memory Feature within five seconds.
Page 138: Memory Position Recall
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 137 NOTE: Your RKE transmitters can be unlinked to the To recall the memory settings for driver one, press memory setting by pressing the SET (S) button followed memory button number 1 or the UNLOCK button on the by the UNLOCK button on the RKE transmitter in Step 4 RKE transmitter linked to memory position 1.
Page 139 138 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • The Easy Entry/Easy Exit feature is disabled when the The distance the driver seat moves depends on where you have the driver seat positioned when you remove the driver’s seat position is less than.9 in (23 mm) forward key from the ignition switch.
Page 140: To Open And Close The Hood
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 139 Outside of the vehicle, locate the safety latch lever TO OPEN AND CLOSE THE HOOD Two latches must be released to open the hood. First, pull between the grille and hood opening (left of center when the hood release lever located under the left side of the facing hood).
Page 141: Lights
140 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • Do not slam the hood to close it. Use a firm downward Use the hood prop rod to secure the hood in the open position. Place the upper end of the prop rod in the hole push at the center front edge of the hood to ensure that on the underside of the hood.
Page 142: Exterior And Interior Lighting Control
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 141 Exterior and Interior Lighting Control The multifunction control lever on the left side of the steering column controls the operation of the headlights, parking lights, turn signal lights, in- strument panel lights, instrument panel light dimming, interior lights, and fog lights (if equipped).
Page 143: Headlights With Wipers (Available With Auto Headlights Only)
142 UNDERSTANDING THE FEATURES OF YOUR VEHICLE headlights will stay on for up to 90 seconds after you turn On with Wipers,” under “Personal Settings (Customer the ignition switch to the LOCK position. To turn the Programmable Features)” under “Electronic Vehicle In- Automatic System off, turn the end of the multifunction formation Center”...
Page 144: Daytime Running Lights (Drl) - If Equipped
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 143 The Headlight delay time is programmable on vehicles Lights-On Reminder equipped with the Electronic Vehicle Information Center If the headlights or parking lights are on after the ignition (EVIC). For details, refer to “Delay Turning Headlights is turned to the LOCK position, a chime will sound to Off,”...
Page 145: Turn Signals
144 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Turn Signals Move the multifunction control lever upward or down- ward and the corresponding turn signal indicator on the instrument panel will flash to show proper operation of the front and rear turn signal lights. Front Fog Light Control NOTE: The front fog lights will only operate with the headlights on low beam.
Page 146: Highbeam/Lowbeam Select Switch
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 145 You can signal a lane change by moving the lever upward or downward partially without moving beyond the de- tent. If either turn signal indicator has a very fast flash rate, check for a defective outside light bulb. If an indicator fails to light when the lever is moved, see your autho- rized dealer for service.
Page 147: Interior Lights
146 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: If the multifunction control lever is held in the on the RKE transmitter, or rotate the Dimmer Control on Flash-to-Pass position for more than 15 seconds, the high the multifunction control lever completely upward to the beams will shut off.
Page 148 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 147 Parade Mode (Daytime Brightness Feature) Rotate the Dimmer Control to the first detent to brighten the odometer and radio display when the parking lights or headlights are on during daylight conditions. Interior Light ON Rotate the Dimmer Control completely upward to the second detent to turn on the interior lights.
Page 149: Windshield Wipers And Washers
148 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WINDSHIELD WIPERS AND WASHERS Rotate the end of the lever to the first detent past the The Windshield Wiper/Washer Control Lever is intermittent settings for low-speed wiper operation, or to located on the right side of the steering column. the second detent past the intermittent settings for high- speed wiper operation.
Page 150: Intermittent Wiper System
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 149 CAUTION! Intermittent Wiper System • Turn the windshield wipers off when driving Use the intermittent wiper system when weather condi- through an automatic car wash. Damage to the tions make a single wiping cycle with a variable pause windshield wipers may result if the wiper control between cycles desirable.
Page 151: Mist Feature
150 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! Sudden loss of visibility through the windshield could lead to an accident. You might not see other vehicles or other obstacles. To avoid sudden icing of the windshield during freezing weather, warm the windshield with defroster before and during wind- shield washer use.
Page 152: Rain Sensing Wipers - If Equipped
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 151 addition, the headlights will turn off when the wipers are position 1 is the least sensitive and wiper delay position turned off if they were turned on by this feature. 5 is the most sensitive. Choose position 3 for normal rain conditions.
Page 153: Windshield Washers
152 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Settings (Customer Programmable Features)” under speed is less than 5 mph (8 km/h), unless the wiper “Electronic Vehicle Information Center (EVIC)” in control is moved or the shift lever is moved out of the Section 4 of this manual.
Page 154: Adding Washer Fluid
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 153 If you activate the washer while the wiper control is in WARNING! the off position, the wipers will operate for two wipe cycles and then turn off. Commercially available windshield washer solvents are flammable. They could ignite and burn you. Care Adding Washer Fluid must be exercised when filling or working around NOTE: Refer to the “Engine Compartment”...
Page 155: Electronic Speed Control - If Equipped
154 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! Do not adjust the steering wheel while driving. The tilt adjustment must be locked while driving. Adjust- ing the steering wheel while driving or driving without the tilt adjustment locked could cause the driver to lose control of the vehicle.
Page 156: To Activate
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 155 and release the ON/OFF button a second time. The Cruise indicator lamp will turn off. Be sure to turn the system off when not in use. NOTE: • The Electronic Speed Control system will automati- cally turn off when the engine is turned off.
Page 157: To Set At A Desired Speed
156 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To Deactivate: WARNING! A soft tap on the brake pedal, or pulling the Speed Control lever toward you (cancel), or normal brake or Leaving the Electronic Speed Control system on clutch pressure while slowing the vehicle will deactivate when not in use is dangerous.
Page 158: To Vary The Speed Setting
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 157 To Vary The Speed Setting: To Accelerate For Passing When the Speed Control is set, you can increase speed by Depress the accelerator as you would normally. When the pushing up and holding the RESUME ACCEL lever. pedal is released, the vehicle will return to the set speed.
Page 159: Rear Park Assist System - If Equipped
158 UNDERSTANDING THE FEATURES OF YOUR VEHICLE System Usage Precautions WARNING! NOTE: Speed Control can be dangerous where the system • Ensure that the rear bumper is free of dirt and debris can’t maintain a constant speed. Your vehicle could to keep the Rear Park Assist System operating prop- go too fast for the conditions, and you could lose erly.
Page 160 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 159 • The Rear Park Assist System, when on, will MUTE the CAUTION! radio when it is sounding a tone. • The Rear Park Assist System is only a parking aid • If a Rear Park Assist System malfunction occurs, a and it is unable to recognize every obstacle, in- single chime will sound once per ignition cycle.
Page 161: Enabling And Disabling The System
160 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! Enabling and Disabling the System • Drivers must be careful when backing up even There are times when you may want to disable the Rear when using the Rear Park Assist System. Always Park Assist System, such as when towing a trailer.
Page 162: System Operation
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 161 Rear Park Assist Switch Rear Park Assist Indicator System Operation The warning display contains two sets of yellow and red The system uses four sensors located in the rear bumper LEDs, one set to warn of obstacles behind the left rear of fascia to scan for obstacles up to 79 in (200 cm) away from the vehicle and the other set to warn of obstacles behind the rear bumper fascia.
Page 163 162 UNDERSTANDING THE FEATURES OF YOUR VEHICLE When the ignition is turned to the ON position, and the driver shifts the transmission into the REVERSE position, system is enabled, the warning display will turn on all of and the vehicle speed is less than 11 mph (18 km/h). The its LEDs for approximately one second.
Page 164: Garage Door Opener - If Equipped
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 163 8th LED 6 in (15 cm) 12 in (30 cm GARAGE DOOR OPENER — IF EQUIPPED HomeLink replaces up to three remote controls (hand-held transmitters) that operate devices such as garage door openers, motorized gates, lighting, or home security systems. The HomeLink unit operates off your vehicle’s battery. The HomeLink buttons that are located in the headliner or sun visor designate the three different HomeLink channels.
Page 165: Programming Homelink
164 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: HomeLink is disabled when the Vehicle Secu- WARNING! rity Alarm is active. Vehicle exhaust contains carbon monoxide, a danger- WARNING! ous gas. Do not run your vehicle in the garage while training the transceiver. Exhaust gas can cause seri- Your motorized door or gate will open and close ous injury or death.
Page 166 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 165 Your vehicle should be parked outside of the garage NOTE: • Some gate operators and garage door openers may when programming. require you to replace Step 3 with procedures noted in 1. Turn the ignition switch to the ON/RUN position. the “Gate Operator/Canadian Programming”...
Page 167 166 UNDERSTANDING THE FEATURES OF YOUR VEHICLE If the indicator light blinks rapidly for two seconds, and then turns to a constant light, continue with program- ming for a Rolling Code. 5. PROGRAMMING A ROLLING CODE SYSTEM At the garage door opener motor (in the garage), locate the “Learn”...
Page 168: Gate Operator/Canadian Programming
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 167 7. Return to the vehicle and press the programmed Similar to this Canadian law, some U.S. gate operators are HomeLink button twice (holding the button for two designed to “time-out” in the same manner. seconds each time).
Page 169: Using Homelink
168 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Then proceed with Step 4 under “Programming 3. Without releasing the button, proceed with Program- HomeLink ” earlier in this section. ming Homelink Step 2 and follow all remaining steps. Using HomeLink Security To operate, simply press and release the programmed It is advised to erase all channels before you sell or turn HomeLink button.
Page 170: General Information
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 169 • Press the “Learn” button on the Garage Door Opener NOTE: The transmitter has been tested and it complies to complete the training for a Rolling Code. with FCC and IC rules. Changes or modifications not expressly approved by the party responsible for compli- •...
Page 171: Opening Sunroof - Express
170 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Opening Sunroof - Express Press the switch rearward and release, and the sunroof will open automatically from any position. The sunroof will open fully and stop automatically. This is called Express Open. During Express Open operation, any movement of the sunroof switch will stop the sunroof.
Page 172: Pinch Protect Feature
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 171 Pinch Protect Feature Venting Sunroof - Express This feature will detect an obstruction in the opening of Press and release the V button, and the sunroof will the sunroof during Express Close operation. If an ob- open to the vent position.
Page 173: Sunroof Maintenance
172 UNDERSTANDING THE FEATURES OF YOUR VEHICLE the rear windows open, then open the front and rear programmable. For details, refer to “Delay Power Off to windows together to minimize the buffeting. If the Accessories Until Exit,” under “Personal Settings (Cus- buffeting occurs with the sunroof open, adjust the sun- tomer Programmable Features)”...
Page 174 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 173 CAUTION! • Never attempt to open or close the Sky Slider when it is frozen. Wait until the Sky Slider is thawed before operating. • Opening the Sky Slider when damp, wet, or dirty can cause stains, mildew, and damage to the soft- top material and the inside of your vehicle.
Page 175: Power Top Control
174 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! Power Top Control • In an accident, there is a greater risk of being The Power Top switch is located between the sun visors thrown from a vehicle with the Sky Slider open. on the overhead console.
Page 176: Opening The Sky Slider
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 175 NOTE: The Power Top switch will operate when the To resume the operation from a partially open position, ignition switch is turned to the ON or ACC position, and press and release the switch once again. when the accessory delay feature is active.
Page 177: Closing The Sky Slider
176 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: The Sky Slider will not open from the front and To resume the operation from a partially closed position, the rear at the same time. The Sky Slider must close fully press and hold the switch once again. before opening it from the opposite end.
Page 178: Anti-Pinch Protect Feature
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 177 windows open, then open the front and rear windows Anti-Pinch Protect Feature The Sky Slider will retract automatically if it detects an together to minimize the buffeting. If the buffeting occurs obstruction while closing. If this occurs, remove the with the Sky Slider open, adjust the Sky Slider opening obstruction and use the switch again to close the Sky to minimize the buffeting or open any window.
Page 179 178 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Front Power Outlet NOTE: If desired, the instrument panel power outlet can be converted by your authorized dealer to provide power with the ignition switch in the LOCK position.
Page 180: Electrical Outlet Use With Engine Off
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 179 Electrical Outlet Use With Engine Off POWER INVERTER — If EQUIPPED CAUTION! Your vehicle may be equipped with a 115 volt AC (150 • Many accessories that can be plugged in draw Watt maximum) power outlet located on the back of the center console.
Page 181 180 UNDERSTANDING THE FEATURES OF YOUR VEHICLE A control switch for the outlet is located in the lower available at the outlet. Press and release the switch again switch bank below the climate controls. to turn off the power outlet. The status indicator will also turn off.
Page 182: Cupholders
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 181 CUPHOLDERS Front and rear cupholders are located in the center console. Rear Cupholders STORAGE Front Cupholders...
Page 183: Front Storage Compartment
182 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Front Storage Compartment Console Storage Compartment The front storage compartment (located on the left side of To open, press the latch and lift the cover. the instrument panel) can hold cell phones, PDAs, and other small items.
Page 184: Cargo Area Features
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 183 Cargo Load Floor The cargo load floor system has a load capacity of 400 lbs (181 kg). The load floor has a built-in storage bin that can hold a variety of items. The underside of the storage bin cover also contains a plastic lined tray.
Page 185 184 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 4. Reinstall the cover with the handle recess facing toward you. NOTE: You can install the cover with either side facing upward. 5. With the cover seated in the floor, pull upward on loops and twist them one-quarter turn so that they are no longer parallel to the slots in the cover.
Page 186 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 185 Cargo Tie-Down Hooks and Loops The tie-downs located on cargo area floor should be used to secure loads safely when the vehicle is moving. Cargo Tie-Down Loops Cargo tie-down loops are located on the trim panels. Cargo Tie-Down Hooks...
Page 187 186 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • Always place cargo evenly on the cargo floor. Put WARNING! heavier objects as low and as far forward as possible. • Cargo tie-downs are not safe anchors for a child • Place as much cargo as possible in front of the rear seat tether strap.
Page 188 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 187 Retractable Cargo Area Cover — If Equipped NOTE: The purpose of this cover is for privacy, not to secure loads. It will not prevent cargo from shifting or protect passengers from loose cargo. The removable retractable cargo area cover mounts in the cargo area behind the top of the rear seats.
Page 189: Rear Window Features
188 UNDERSTANDING THE FEATURES OF YOUR VEHICLE notches in the trim panels. Then, lower the cover to WARNING! position the posts into the bottom of the notches and release the handle. In an accident, a cargo cover loose in the vehicle could cause injury.
Page 190 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 189 switch. Once released, the wiper will cycle three times, return to the park position, and then resume normal operation. NOTE: The rear wiper will automatically return to the park position if you turn OFF the ignition switch while it is operating.
Page 191: Rear Window Defroster - If Equipped
190 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Adding Washer Fluid CAUTION! The windshield washer and rear window washer share the same fluid reservoir. The reservoir is located in the • Turn the rear wiper off when driving through an front of the engine compartment. Be sure to check the automatic car wash.
Page 192: Roof Luggage Rack - If Equipped
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 191 ROOF LUGGAGE RACK — IF EQUIPPED CAUTION! The load carried on the roof, when equipped with a luggage rack, must not exceed 150 lbs (68 kg), and it • Use care when washing the inside of the rear should be uniformly distributed over the cargo area.
Page 193 192 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CAUTION! WARNING! To avoid damage to the roof rack and vehicle, do not Cargo must be securely tied down before driving exceed the maximum roof rack load capacity. Always your vehicle. Improperly secured loads can fly off the distribute heavy loads as evenly as possible and vehicle, particularly at high speeds, resulting in per- secure the load appropriately.
Page 194 INSTRUMENT PANEL AND CONTROLS CONTENTS ▫ Telephone (UConnect ) — If Equipped ..222 Instrument Panel Features ....196 ▫...
Page 195 194 INSTRUMENT PANEL AND CONTROLS Sales Code REQ — AM/FM Stereo Radio And Sales Code RES — AM/FM Stereo Radio With CD 6–Disc CD/DVD Changer (MP3/WMA AUX Jack) 230 Player (MP3 AUX Jack) ....250 ▫...
Page 196: Instrument Panel And Controls
INSTRUMENT PANEL AND CONTROLS 195 ▫ Satellite Antenna ..... . 264 ▫ Left-Hand Switch Functions For Radio Operation 268 ▫ Reception Quality ..... 264 ▫...
Page 197: Instrument Panel Features
196 INSTRUMENT PANEL AND CONTROLS INSTRUMENT PANEL FEATURES 1 — Air Outlet 5 — Radio 9 — Lower S 2 — Instrument Cluster 6 — Glove Box 10 — Storag 3 — Storage Tray 7 — Climate Control 4 — Center Air Outlet 8 —...
Page 198: Instrument Cluster
INSTRUMENT PANEL AND CONTROLS 197 INSTRUMENT CLUSTER...
Page 199: Instrument Cluster Descriptions
198 INSTRUMENT PANEL AND CONTROLS INSTRUMENT CLUSTER DESCRIPTIONS 4. Tire Pressure Monitoring Telltale Light — If Equipped 1. Fuel Gauge Each tire, including the spare (if provided), The fuel gauge shows level of fuel in tank when should be checked monthly when cold and ignition switch is in the ON position.
Page 200 INSTRUMENT PANEL AND CONTROLS 199 can lead to tire failure. Under-inflation also reduces fuel as intended. TPMS malfunctions may occur for a variety efficiency and tire tread life, and may affect the vehicle’s of reasons, including the installation of replacement or handling and stopping ability.
Page 201 200 INSTRUMENT PANEL AND CONTROLS engine is running. If the light remains lit with the engine CAUTION! running your vehicle will usually be drivable and not need towing, however see your authorized dealer for The TPMS has been optimized for the original service as soon as possible.
Page 202 INSTRUMENT PANEL AND CONTROLS 201 position before engine start. If the light does not turn on CAUTION! when turning the key from LOCK or ACC to ON, have the condition checked promptly. Prolonged driving with the MIL on could cause damage to the engine control system.
Page 203 202 INSTRUMENT PANEL AND CONTROLS 9. Speedometer adapt your speed and driving to the prevailing road Shows the vehicle speed. conditions. (See page 327 for more information.) 10. Turn Signal Indicator Light 12. Charging System Warning Light The left or right arrow will flash in unison with the This light shows the status of the electrical charg- corresponding front and rear turn signal lights when ing system.
Page 204 INSTRUMENT PANEL AND CONTROLS 203 started. If the light does not turn on during starting, have the conventional brake system will continue to operate the system checked by an authorized dealer. normally, provided the BRAKE warning light is not on. If the light turns on and remains on while driving, safely If the ABS light is on, the brake system should be serviced bring the vehicle to a stop and shut off the engine.
Page 205 204 INSTRUMENT PANEL AND CONTROLS 16. 4 LOW Mode Indicator Light — If Equipped 18. TOW/HAUL Indicator Light — If Equipped This light alerts the driver that the vehicle is in This light will illuminate when selecting the 4WD LOW mode. In this mode, the front TOW/HAUL.
Page 206 INSTRUMENT PANEL AND CONTROLS 205 20. Electronic Stability Program (ESP)/Brake Assist NOTE: Each time the ignition switch is turned ON, the System (BAS) Malfunction Indicator Light – If ESP System will be on even if it was turned off previ- Equipped ously.
Page 207 206 INSTRUMENT PANEL AND CONTROLS on, turn it off. Also, shift the transmission into NEUTRAL CAUTION! and idle the vehicle. If the temperature reading does not return to normal, turn the engine off immediately and Driving with a hot cooling system could damage call for service.
Page 208 INSTRUMENT PANEL AND CONTROLS 207 the air conditioner is on, turn it off. Also, shift the WARNING! transmission into NEUTRAL and idle the vehicle. If the needle remains on the “H” mark, turn the engine OFF A hot engine cooling system is dangerous. You or immediately and call for service.
Page 209 208 INSTRUMENT PANEL AND CONTROLS 24. Transmission Temperature Warning Light — If once again to display the outside temperature and com- pass heading in the screen below the speedometer. Refer Equipped This light indicates that the transmission fluid to “Vacuum Fluorescent Display” for details. temperature is running hot.
Page 210 INSTRUMENT PANEL AND CONTROLS 209 27. Odometer/Trip Odometer NOTE: If the instrument cluster is equipped with the The odometer shows the total distance the vehicle has optional Electronic Vehicle Information Center (EVIC), been driven. The trip odometer shows individual trip then most warnings will display in the EVIC.
Page 211 210 INSTRUMENT PANEL AND CONTROLS Change Oil Message (Base And Mid Line Clusters 1. Turn the ignition switch to the ON position. Do not Only) start the engine. Your vehicle is equipped with an engine oil change 2. Fully depress the accelerator pedal slowly three indicator system.
Page 212 INSTRUMENT PANEL AND CONTROLS 211 30. Seat Belt Reminder Light indicated by the Brake Warning Light, which will turn on This light will turn on for several seconds after the when the brake fluid level in the master cylinder has ignition is turned ON as a reminder to “buckle dropped below a specified level.
Page 213 212 INSTRUMENT PANEL AND CONTROLS Vehicles equipped with Anti-Lock Brakes (ABS), are also 32. Vehicle Security Alarm Indicator Light — If equipped with Electronic Brake Force Distribution (EBD). Equipped In the event of an EBD failure, the Brake Warning Light This light will flash rapidly for approximately will turn on along with the ABS Light.
Page 214 INSTRUMENT PANEL AND CONTROLS 213 34. Vacuum Fluorescent Display (Mid Line And NOTE: Magnetic materials should be kept away from Premium Clusters Only) the top of the right rear quarter window. This is where On vehicles equipped with a Premium Cluster, this the compass sensor is located.
Page 215 214 INSTRUMENT PANEL AND CONTROLS NOTE: The factory default Zone is 8. During program- ming, the Zone value will wrap around from zone 15 to Zone 1. Calibrating the Compass (Mid Line Cluster Only) If the compass appears erratic, inaccurate, or abnormal, you may wish to calibrate it.
Page 216: Electronic Vehicle Information Center (Evic) - If Equipped
INSTRUMENT PANEL AND CONTROLS 215 • Compass display vehicle in one or more complete circles, at speeds under 5 mph (8 km/h), in an area free from power lines and • Outside temperature display large metallic objects, until the “CAL” indicator turns off. •...
Page 217: Electronic Vehicle Information Center (Evic) Displays
216 INSTRUMENT PANEL AND CONTROLS Press the SCROLL button to scroll through Trip Electronic Vehicle Information Center (EVIC) Functions, Navigation (if equipped), System Displays Status Messages, and Personal Settings (Cus- When the appropriate conditions exist, the Electronic tomer Programmable Features). Vehicle Information Center (EVIC) displays the following SCROLL messages:...
Page 218 INSTRUMENT PANEL AND CONTROLS 217 • Memory System Disabled – Vehicle Not in Park (with • Liftgate Ajar (with a single chime) a single chime) — automatic transmission • Left Front Low Pressure (with a single chime). Refer to • Memory System Disabled – Vehicle in Motion (with a “Tire Pressure Monitoring System”...
Page 219: Oil Change Required
218 INSTRUMENT PANEL AND CONTROLS • Check Gascap (refer to “Adding Fuel” in Section 5 of MENU button. To reset the oil change indicator system this manual for more details) (after performing the scheduled maintenance) perform the following procedure: • Service Park Assist System (with a single chime) 1.
Page 220 INSTRUMENT PANEL AND CONTROLS 219 • Elapsed Time and average fuel economy, according to the current fuel tank level. DTE cannot be reset through the FUNCTION • Display Units of Measure in SELECT button. Press the SCROLL button to cycle through all the Trip NOTE: Significant changes in driving style or vehicle Computer functions.
Page 221: Compass Display
220 INSTRUMENT PANEL AND CONTROLS • Display Units of Measure in: Automatic Compass Calibration To make your selection, press and release the FUNC- This compass is self-calibrating, which eliminates the TION SELECT button until “US” or “METRIC” appears. need to set the compass manually. When the vehicle is new, the compass may appear erratic and the EVIC will To Reset The Display display “CAL”...
Page 222 INSTRUMENT PANEL AND CONTROLS 221 3. Press the SCROLL button until “Calibrate Compass” NOTE: Magnetic materials should be kept away from displays in the EVIC. the top of the right rear quarter window. This is where the compass sensor is located. 4.
Page 223: Telephone (Uconnect ) - If Equipped
222 INSTRUMENT PANEL AND CONTROLS 1. Turn the ignition switch ON. 2. Press and hold the COMPASS button for approxi- mately two seconds. 3. Press the SCROLL button until “Compass Variance” message and the last variance zone number displays in the EVIC.
Page 224 INSTRUMENT PANEL AND CONTROLS 223 • Phone status: idle, voice mail, roaming, battery The EVIC displays this symbol to indicate an strength, and signal strength in increments of 20 incoming call. percent. Incom- • Call status: Incoming call, connecting, connected, air- ing Call time in minutes and seconds, call ended, call failed, The EVIC displays this symbol to indicate that...
Page 225: Personal Settings (Customer Programmable Features)
224 INSTRUMENT PANEL AND CONTROLS The EVIC displays this symbol to indicate that The EVIC displays this symbol to indicate that you have voice mail. a phone connection has been made. Voice Call in Mail Progress The EVIC displays this symbol to indicate a The EVIC displays this symbol to indicate that text message.
Page 226 INSTRUMENT PANEL AND CONTROLS 225 Press and release the MENU button until Personal Set- For vehicles equipped with sales code RER radio, refer to tings displays in the EVIC. your “Navigation User’s Manual” for UConnect system operating instructions. Use the SCROLL button to display one of the following choices: Lock Doors Automatically at 15 mph (24 km/h) When on is selected, all doors will lock automatically...
Page 227 226 INSTRUMENT PANEL AND CONTROLS Door 1st Press is selected, you must press of the RKE your selection, press and release the FUNCTION SE- transmitter UNLOCK button twice to unlock the passen- LECT button until “ON” or “OFF” appears. Refer to ger’s doors.
Page 228 INSTRUMENT PANEL AND CONTROLS 227 Automatically Move Seat Back on Exit — If your selection, press and release the FUNCTION SE- Equipped LECT button until “On” or “Off” appears. This feature provides automatic driver seat positioning to Headlights On with Wipers (Available with Auto enhance driver mobility when entering and exiting the Headlights Only) vehicle.
Page 229 228 INSTRUMENT PANEL AND CONTROLS when exiting the vehicle. To make your selection, press your selection, press and release the FUNCTION SE- and release the FUNCTION SELECT button until “0,” LECT button until “Off,” “45 sec.,” “5 min.,” or “10 min.” “30,”...
Page 230: Radio General Information
INSTRUMENT PANEL AND CONTROLS 229 km/h). Refer to “Rear Park Assist System” in Section 3 of you understand and save you concern about these “ap- this manual for system function and operating informa- parent” malfunctions, you must understand a point or tion.
Page 231: Am Reception
230 INSTRUMENT PANEL AND CONTROLS AM Reception switch is turned to the LOCK position. Opening either AM sound is based on wave amplitude, so AM reception front door will cancel this feature. The time is program- can be disrupted by such things as lightning, power lines mable.
Page 232: Operating Instructions - Radio Mode
INSTRUMENT PANEL AND CONTROLS 231 Power Switch/Volume Control (Rotary) Push the ON/VOLUME control knob to turn on the radio. Press the ON/VOLUME control knob a second time to turn off the radio. Electronic Volume Control The electronic volume control turns continuously (360 degrees) in either direction without stopping.
Page 233 232 INSTRUMENT PANEL AND CONTROLS SCAN Button Phone Button (UConnect Hands-Free Phone) — If Pressing the SCAN button causes the tuner to search for Equipped the next listenable station, in AM, FM or Satellite (if Press this button to operate the Hands-Free Phone equipped) frequencies, pausing for five seconds at each (UConnect ) feature (if equipped).
Page 234 INSTRUMENT PANEL AND CONTROLS 233 3. After adjusting the hours, press the right side TUNE/ RW/FF SCROLL control knob to set the minutes. The minutes Pressing the RW (Rewind) or FF (Fast Forward) buttons will begin to blink. causes the tuner to search for the next frequency in the direction of the arrows.
Page 235 234 INSTRUMENT PANEL AND CONTROLS Push the rotary TUNE/SCROLL control knob a third or turning the TUNE/SCROLL control knob within five time and TREBLE will display. Turn the TUNE/SCROLL seconds will allow the program format type to be se- control knob to the right or left to increase or decrease the lected.
Page 236 INSTRUMENT PANEL AND CONTROLS 235 16-Digit Character Dis- 16-Digit Character Dis- Program Type Program Type play play Jazz Jazz Top 40 Top 40 News News Weather Weather Nostalgia Nostalga By pressing the SEEK button when the Music Type icon Oldies Oldies is displayed, the radio will be tuned to the next frequency Personality...
Page 237 236 INSTRUMENT PANEL AND CONTROLS • Audio Stream – Repeatedly pressing SELECT will NOTE: Turn the TUNE/SCROLL control knob to scroll through the entries. Push the AUDIO/SELECT button to switch to different audio languages (if supported on select an entry and make changes. the disc) (if equipped).
Page 238 INSTRUMENT PANEL AND CONTROLS 237 • VES CH1/CH2 - Allows the user to change the mode Enter the four-digit country code using the TUNE/ of either the IR1 or IR2, wireless headphones by SCROLL control knob to scroll up and down to select the pressing the AUDIO/SELECT button (if equipped).
Page 239 238 INSTRUMENT PANEL AND CONTROLS Subtitles — If Equipped auto-play the main title. In such cases, use the MENU button on the remote control to select desired title to play. Selecting this item allows you to choose between subtitle Off or On. NOTE: The user will have to set these defaults before loading a disc.
Page 240: Operation Instructions - (Disc Mode For Cd And Mp3/Wma Audio Play, Dvd-Video)
INSTRUMENT PANEL AND CONTROLS 239 You may add a second station to each pushbutton by Operation Instructions - (DISC MODE for CD and repeating the above procedure with this exception: Press MP3/WMA Audio Play, DVD-VIDEO) the SET button twice and SET 2 will show in the display The radio DVD player and many DVD discs are coded by window.
Page 241 240 INSTRUMENT PANEL AND CONTROLS NOTE: The ignition switch must be in the ON or ACC Eject Button — Ejecting Compact Disc(s) position to operate the radio. Press the EJECT button and the pushbutton with the corresponding number (1-6) where the LOAD Button —...
Page 242: Notes On Playing Mp3/Wma Files
INSTRUMENT PANEL AND CONTROLS 241 SCAN Button (CD MODE) Notes On Playing MP3/WMA Files Press the SCAN button to scan through each track on the The radio can play MP3/WMA files; however, acceptable CD currently playing. MP3/WMA file recording media and formats are limited. When writing MP3/WMA files, pay attention to the TIME Button (CD MODE) following restrictions.
Page 243 242 INSTRUMENT PANEL AND CONTROLS • Maximum number of directory levels: 8 If a disc contains multi-formats, such as CD audio and MP3/WMA tracks, the radio will only play the MP3/ • Maximum number of files: 255 WMA tracks on that disc. •...
Page 244 INSTRUMENT PANEL AND CONTROLS 243 Playback of MP3/WMA Files MPEG Specifi- Sampling Fre- Bit Rate (kbps) When a medium containing MP3/WMA data is loaded, cation quency (kHz) the radio checks all files on the medium. If the medium 320, 256, 224, contains a lot of folders or files, the radio will take more MPEG-1 Audio 192, 160, 128,...
Page 245: List Button (Disc Mode For Mp3/Wma Play)
244 INSTRUMENT PANEL AND CONTROLS LIST Button (DISC Mode for MP3/WMA Play) Press and hold the INFO button again for three seconds Pressing the LIST button will bring up a list of all folders to return to elapsed time display. on the disc.
Page 246 INSTRUMENT PANEL AND CONTROLS 245 SCAN Button (Auxiliary Mode) Operating Instructions — Voice Recognition No function. System (VR) (If Equipped) For the radio, refer to “Voice Recognition System (VR)” in EJECT Button (Auxiliary Mode) Section 3. No function. For UConnect “Voice Recognition System (VR),” refer to “Hands-Free Communication (UConnect )”...
Page 247: Sales Code Rer - Multimedia System - If Equipped
246 INSTRUMENT PANEL AND CONTROLS Dolby SALES CODE RER — MULTIMEDIA SYSTEM — IF Manufactured under license from Dolby Laboratories. EQUIPPED Dolby and the double-D symbol are trademarks of NOTE: The sales code is located on the lower right side Dolby Laboratories.
Page 248: Operating Instructions - Satellite Radio
INSTRUMENT PANEL AND CONTROLS 247 The satellite navigation capability combines a Global- Other special features include direct tune, music type Positioning System (GPS)-based navigation system with selections, traffic messaging (optional), easy store presets, an integrated color screen to provide maps, turn identi- parental lockout for VES (if equipped), backup camera fication, selection menus, and instructions for selecting a display for vehicles equipped with a backup camera, and...
Page 249: Clock Setting Procedure
248 INSTRUMENT PANEL AND CONTROLS Clock Setting Procedure 4. Touch the screen where the words “Set Time Zone” are The GPS receiver in this system is synchronized to the displayed. The time zone selection menu will appear on time data being transmitted by the GPS satellites. The the screen.
Page 250 INSTRUMENT PANEL AND CONTROLS 249 3. When this feature is on, a check mark will appear in 4. To move the hour forward, touch the screen where the the box next to the words “Daylight Savings.” Touch the word “Hour” with the arrow pointing upward is dis- screen where the words “Daylight Savings”...
Page 251: Sales Code Res - Am/Fm Stereo Radio With Cd Player (Mp3 Aux Jack)
250 INSTRUMENT PANEL AND CONTROLS 2. Touch the screen where the time is displayed. The clock setting menu will appear on the screen. 3. When this feature is on, a check mark will appear in the box next to the words “Show Time if Radio is Off.” Touch the screen where the words “Show Time if Radio is Off”...
Page 252 INSTRUMENT PANEL AND CONTROLS 251 Power Switch/Volume Control (Rotary) SCAN Button Push the ON/VOLUME control knob to turn on the Pressing the SCAN button causes the tuner to search for radio. Push the ON/VOLUME control knob a second the next listenable station in AM or FM frequencies, time to turn off the radio.
Page 253 252 INSTRUMENT PANEL AND CONTROLS Phone Button (UConnect Hands-Free Phone) — If 3. After adjusting the hours, press the right side TUNE/ SCROLL control knob to set the minutes. The minutes Equipped Press this button to operate the Hands-Free Phone will begin to blink.
Page 254 INSTRUMENT PANEL AND CONTROLS 253 INFO Button Push the rotary TUNE/SCROLL control knob a second Press the INFO button for an RDS station (one with call time and MID will display. Turn the TUNE/SCROLL letters displayed). The radio will return a Radio Text control knob to the right or left to increase or decrease the message broadcast from an FM station (FM mode only).
Page 255 254 INSTRUMENT PANEL AND CONTROLS Push the rotary TUNE/SCROLL control knob again to 16-Digit Character Dis- Program Type exit setting tone, balance, and fade. play Classic Rock Cls Rock MUSIC TYPE Button College College Pressing this button once will turn on the Music Type mode for five seconds.
Page 256 INSTRUMENT PANEL AND CONTROLS 255 SETUP Button 16-Digit Character Dis- Program Type Pressing the SETUP button allows you to select between play the following items: Soft Soft • Set Clock — Pressing the SELECT button will allow Soft Rock Soft Rck you to set the clock.
Page 257: Operation Instructions - Cd Mode For Cd And Mp3 Audio Play
256 INSTRUMENT PANEL AND CONTROLS selected within five seconds after pressing the SET but- DISC Button ton, the station will continue to play but will not be Pressing the DISC button will allow you to switch from stored into pushbutton memory. AM/FM modes to Disc modes.
Page 258 INSTRUMENT PANEL AND CONTROLS 257 an inch (2.5 cm), a disc may already be loaded and must CAUTION! be ejected before a new disc can be loaded. • This CD player will accept 4–3/4 in (12 cm) discs If you insert a disc with the ignition ON and the radio only.
Page 259 258 INSTRUMENT PANEL AND CONTROLS If you have ejected a disc and have not removed it within TIME Button 10 seconds, it will be reloaded. If the CD is not removed, Press this button to change the display from a large CD the radio will reinsert the CD but will not play it.
Page 260: Notes On Playing Mp3 Files
INSTRUMENT PANEL AND CONTROLS 259 Press the right SEEK button to move to the next ran- files properly and may be unable to play the file nor- domly selected track. mally. UDF and Apple HFS formats are not supported. Press the RND button a second time to stop Random The radio uses the following limits for file systems: Play.
Page 261 260 INSTRUMENT PANEL AND CONTROLS • Level 2: 31 (including a separator . and a three- rates (VBR) are also supported. The majority of MP3 files character extension) use a 44.1 kHz sampling rate and a 192, 160, 128, 96 or VBR bit rates.
Page 262: List Button (Cd Mode For Mp3 Play)
INSTRUMENT PANEL AND CONTROLS 261 Playback of MP3 Files LIST Button (CD Mode for MP3 Play) When a medium containing MP3 data is loaded, the Pressing the LIST button will bring up a list of all folders radio checks all files on the medium. If the medium on the disc.
Page 263 262 INSTRUMENT PANEL AND CONTROLS Press and hold the INFO button again for three seconds TIME Button (Auxiliary Mode) to return to elapsed time display. Press this button to change the display to time of day. The time of day will display for five seconds (when ignition is Operation Instructions - Auxiliary Mode OFF).
Page 264: Satellite Radio - If Equipped (Ren/Req/Rer/Res Radios Only)
INSTRUMENT PANEL AND CONTROLS 263 number 888-539-7474, or visit the Sirius web site at SATELLITE RADIO — IF EQUIPPED (REN/REQ/RER/RES RADIOS ONLY) www.sirius.com, or at www.siriuscanada.ca for Cana- Satellite radio uses direct satellite-to-receiver broadcast- dian residents. ing technology to provide clear digital sound, coast to Electronic Serial Number/Sirius Identification coast.
Page 265: Selecting Satellite Mode
264 INSTRUMENT PANEL AND CONTROLS Sirius ID number will display. The Sirius ID number antenna will cause decreased performance. Larger lug- display will time out in two minutes. Press any button on gage items such as bikes should be placed as far rearward the radio to exit this screen.
Page 266: Operating Instructions - Satellite Mode
INSTRUMENT PANEL AND CONTROLS 265 INFO Button Operating Instructions - Satellite Mode Pressing the INFO button will cycle between Artist, Song NOTE: The ignition switch must be in the ON or ACC Title, and Composer (if available) information. Also, position to operate the radio. pressing and holding the INFO button for an additional SEEK Buttons three seconds will make the radio display the Song Title...
Page 267 266 INSTRUMENT PANEL AND CONTROLS • Display Sirius ID number — Press the AUDIO/ or turning the TUNE/SCROLL control knob within five seconds will allow the program format type to be se- SELECT button to display the Sirius ID number. This lected.
Page 268: Operating Instructions - Hands-Free Phone
INSTRUMENT PANEL AND CONTROLS 267 pushbutton memory. The channels stored in SET 2 REMOTE SOUND SYSTEM CONTROLS — IF memory can be selected by pressing the pushbutton EQUIPPED twice. The remote sound system controls are located on the rear surface of the steering wheel. The left- and right-hand Every time a preset button is used, a corresponding controls are rocker-type switches with a pushbutton in button number will display.
Page 269: Right-Hand Switch Functions
268 INSTRUMENT PANEL AND CONTROLS Left-Hand Switch Functions for Radio Operation • Press the top of the switch to SEEK the next listenable station up from the current setting. • Press the bottom of the switch to SEEK the next listenable station down from the current setting.
Page 270: Cd/Dvd Disc Maintenance
INSTRUMENT PANEL AND CONTROLS 269 • Press the switch up or down twice to listen to the 5. Store the disc in its case after playing. second track, three times to listen to the third track, 6. Do not expose the disc to direct sunlight. and so forth.
Page 271: Manual Air Conditioning And Heating System
270 INSTRUMENT PANEL AND CONTROLS Manual Air Conditioning and Heating System Blower Control Use this control to regulate the amount of air forced through the ven- tilation system in any mode. The blower speed increases as you move the control to the right from the “O” (Off) position.
Page 272 INSTRUMENT PANEL AND CONTROLS 271 • Panel NOTE: If your air conditioning performance seems lower than expected, check the front of the A/C con- Air is directed through the outlets in the instru- denser (located in front of the radiator) for an accumu- ment panel.
Page 273 272 INSTRUMENT PANEL AND CONTROLS • Floor Conditioning Snowflake button is not pressed. This de- Air is directed through the floor outlets with a humidifies the air to help dry the windshield. To improve small amount flowing through the defrost and fuel economy, use these modes only when necessary.
Page 274 INSTRUMENT PANEL AND CONTROLS 273 • Economy Mode because of moisture build-up inside the vehicle. Select the Outside Air position for maximum defogging. If economy mode is desired, press the A/C button to turn off the indicator light and the A/C compressor. Then, •...
Page 275: Automatic Temperature Control (Atc) - If Equipped
274 INSTRUMENT PANEL AND CONTROLS Automatic Temperature Control (ATC) — If cabin infrared sensor mounted between the sun-visors and from various sensors located throughout the vehicle. Equipped The controls on the climate control provide the system with operator input. Other sensors take account of ve- hicle speed, A/C pressure, outside temperature, and engine cooling temperature.
Page 276 INSTRUMENT PANEL AND CONTROLS 275 2. Dial in the temperature you would NOTE: • The temperature setting can be adjusted at anytime like the system to maintain by rotating the Temperature Control knob. without affecting automatic operation. • Pressing the Air Conditioning Control button while in AUTO mode will cause the LED in the control button to flash three times and then turn off.
Page 277 276 INSTRUMENT PANEL AND CONTROLS Mode Preferred Automatic, or Blower and Mode Pre- rotating the Blower Control knob (on the left). ferred Automatic. This means the operator can override NOTE: Please read the Automatic Temperature Control the blower, the mode, or both. There is a manual blower Operation Chart that follows for details.
Page 278 INSTRUMENT PANEL AND CONTROLS 277...
Page 279 278 INSTRUMENT PANEL AND CONTROLS The operator can override the AUTO mode setting to lower outlets. The warmer air flows to the floor outlets. change airflow distribution by rotating the Mode Control This feature gives improved comfort during sunny but knob (on the right) to one of the following positions.
Page 280 INSTRUMENT PANEL AND CONTROLS 279 maximum blower and temperature settings for best Activating recirculation will cause the LED in the windshield and side window defrosting. CONTROL button to illuminate. After ten minutes, the system will return to normal AUTO mode function •...
Page 281: Operating Tips
280 INSTRUMENT PANEL AND CONTROLS hamper visibility. For this reason, the system will not Operating Tips allow Recirculation to be selected while in floor, de- NOTE: Refer to the chart at the end of this section for frost, or defrost/floor mode. Attempting to use the suggested control settings for various weather condi- Recirculation while in these modes will cause the LED tions.
Page 282 INSTRUMENT PANEL AND CONTROLS 281 Vacation Storage Side Window Demisters Anytime you store your vehicle, or keep it out of service A side window demister outlet is located at each end of (i.e., vacation) for two weeks or more, run the air the instrument panel.
Page 283 282 INSTRUMENT PANEL AND CONTROLS outside the vehicle and recirculated air within the pas- senger compartment. Refer to “Maintenance Procedures” in Section 7 of this manual for A/C Air Filter service information or see your authorized dealer for service. Refer to the “Maintenance Schedules” in Section 8 of this manual for filter service intervals.
Page 284 INSTRUMENT PANEL AND CONTROLS 283 Control Setting Suggestions for Various Weather Conditions...
Page 286: Starting And Operating
STARTING AND OPERATING CONTENTS ▫ Shift Lock Manual Override — If Equipped . . . 294 Starting Procedures ..... 289 ▫...
Page 287 286 STARTING AND OPERATING ▫ MP3022 Selec-Trac II Transfer Case — If Electronic Brake Control System ... . 327 Equipped ......310 ▫...
Page 288 STARTING AND OPERATING 287 ▫ Tire Identification Number (TIN) ..345 Tire Rotation Recommendations ... . 360 ▫ Tire Loading And Tire Pressure ... 347 Tire Pressure Monitor System (TPMS) —...
Page 289 288 STARTING AND OPERATING ▫ Trailer Towing Weights (Maximum Trailer Weight Adding Fuel ......375 Ratings) .
Page 290: Starting Procedures
STARTING AND OPERATING 289 STARTING PROCEDURES Manual Transmission — If Equipped Before starting your vehicle, adjust your seat, adjust both Apply the parking brake, place the shift lever in NEU- inside and outside mirrors, and fasten your seat belts. TRAL and depress the clutch pedal before starting ve- hicle.
Page 291: Extreme Cold Weather (Below -20°F Or -29°C)
290 STARTING AND OPERATING Turn the ignition switch to the START position and Extreme Cold Weather (below –20°F or –29°C) release when the engine starts. If the engine fails to start To ensure reliable starting at these temperatures, use of within 10 seconds, turn the ignition switch to the LOCK an externally powered electric engine block heater (avail- position, wait 10 to 15 seconds, then repeat the normal...
Page 292: If Engine Fails To Start
STARTING AND OPERATING 291 If Engine Fails to Start Without Tip Start (Manual Transmission Only) WARNING! If the engine fails to start after you have followed the “Normal Starting” or “Extreme Cold Weather” proce- • Never pour fuel or other flammable liquids into dures, it may be flooded.
Page 293: After Starting
292 STARTING AND OPERATING seconds with the accelerator pedal pushed all the way to CAUTION! the floor. Release the accelerator pedal and the key once the engine is running smoothly. To prevent damage to the starter, wait 10 to 15 seconds before trying again.
Page 294: Engine Block Heater - If Equipped
STARTING AND OPERATING 293 ENGINE BLOCK HEATER — IF EQUIPPED AUTOMATIC TRANSMISSION The engine block heater warms the engine coolant and CAUTION! permits quicker starts in cold weather. Connect the cord to a standard 110-115 volt AC electrical outlet with a Damage to the transmission may occur if the follow- grounded three-wire extension cord.
Page 295: Shift Lock Manual Override - If Equipped
294 STARTING AND OPERATING 1. Firmly set the parking brake. WARNING! 2. Using a flat blade screwdriver, carefully remove the It is dangerous to shift lever out of PARK or NEU- shift lock manual override cover, which is located on the TRAL if the engine speed is higher than idle speed.
Page 296: Brake/Transmission Interlock System
STARTING AND OPERATING 295 Brake/Transmission Interlock System This system prevents you from moving the shift lever out of PARK and into any gear unless the brake pedal is pressed. Always depress the brake pedal first, before moving the shift lever out of PARK. 4–Speed Automatic Transmission Shifting from DRIVE to PARK or REVERSE should be done only after the accelerator pedal is released and the...
Page 297 296 STARTING AND OPERATING this range. Never use PARK while the vehicle is in motion. Apply the parking brake when leaving the vehicle in this range. Always apply the parking brake first, and then place the shift lever in PARK position. WARNING! Never use PARK position as a substitute for the parking brake.
Page 298 STARTING AND OPERATING 297 NEUTRAL WARNING! Shift into NEUTRAL when the vehicle is standing for prolonged periods with the engine running. The engine It is dangerous to shift the shift lever out of PARK or may be started in this range. Set the parking brake if you NEUTRAL if the engine speed is higher than idle must leave the vehicle.
Page 299 298 STARTING AND OPERATING (First) however, automatically select the most desirable gear For hard pulling at low speeds in mud, sand, snow, or on for operation at this temperature. Normal operation steep grades. The transmission begins and stays in low will resume when the transmission fluid temperature gear with no upshift.
Page 300 STARTING AND OPERATING 299 When To Use TOW/HAUL Mode When driving in hilly areas, towing a trailer, carrying a heavy load, etc., and frequent transmission shifting oc- curs, press the TOW/HAUL button. This will improve performance and reduce the potential for transmission overheating or failure due to excessive shifting.
Page 301 300 STARTING AND OPERATING Torque Converter Clutch A Reset feature allows the vehicle to be driven to an A feature designed to improve fuel economy has been authorized dealer for service without damaging the added to the automatic transmission of this vehicle. A transmission.
Page 302: Manual Transmission - If Equipped
STARTING AND OPERATING 301 PARK, REVERSE, and NEUTRAL will continue to oper- CAUTION! ate. Only second gear range will operate in the DRIVE position. Have the transmission checked at your autho- Never drive with your foot resting on the clutch rized dealer as soon as possible.
Page 303: Shifting
302 STARTING AND OPERATING You should always use 1st gear when starting from a standing position if under heavy load or when pulling a trailer. Recommended Vehicle Shift Speeds To utilize your manual transmission efficiently for both fuel economy and performance, it should be upshifted as listed in recommended shift speed chart.
Page 304: Downshifting
STARTING AND OPERATING 303 Downshifting CAUTION! Moving from a high gear down to a lower gear is When descending a hill, be very careful to downshift recommended to preserve brakes when driving down one gear at a time to prevent over-speeding the steep hills.
Page 305: Four-Wheel Drive Operation
304 STARTING AND OPERATING When additional traction is required, select the transfer Gear Selection 6 to 5 5 to 4 4 to 3 3 to 2 2 to 1 case 4WD LOCK position or 4WD LOW position. This Maximum Speed 85 mph (135 km/h) 75 mph (120 km/h) 55 mph (88 km/h)
Page 306 STARTING AND OPERATING 305 CAUTION! • Do not attempt to make a shift while only the front wheels or rear wheels are spinning. The MP1522 Command-Trac transfer case is not equipped with a synchronizer and therefore the speed of the front driveshaft and rear driveshaft must be equal for the shift to take place.
Page 307 306 STARTING AND OPERATING WARNING! Shift Positions • You or others could be injured if you leave the The electronic transfer case switch is located on the center vehicle unattended with the transfer case in the console next to the shift lever. NEUTRAL position without first fully engaging the parking brake.
Page 308 STARTING AND OPERATING 307 Interlocking Ignition System” under “Manual Transmis- Rear Wheel Drive High Range - Normal street and sion” or to “Starting Procedures” in this section for highway driving on dry hard-surfaced roads. details. 4WD Lock 4-Wheel Drive High Range - Locks the front driveshaft NEUTRAL - Disengages both the front driveshaft and and rear driveshaft together and forces the front and rear rear driveshaft from the powertrain.
Page 309 308 STARTING AND OPERATING If One or More Shift Requirements are not met: the 4WD Control Switch back to the original position, make certain all shift requirements have been met, wait • An indicator light will flash. five seconds, and try the shift again. •...
Page 310 STARTING AND OPERATING 309 position indicator light will remain ON. At this time, Preferred Procedure reduce speed and stop spinning the wheels to com- 1. With the engine RUNNING, slow the vehicle speed to plete the shift. There may be a delay up to 10 seconds 2 to 3 mph (3 to 5 km/h).
Page 311: Mp3022 Selec-Trac Ii Transfer Case - If Equipped
310 STARTING AND OPERATING 2. With the ignition switch in the ON position, and the original position, make certain all shift requirements engine OFF or RUNNING, shift the transmission into have been met, wait five seconds, and try the shift NEUTRAL (automatic transmission), or depress the again.
Page 312 STARTING AND OPERATING 311 • 4-wheel drive (4WD) Low range. CAUTION! This transfer case is intended to be driven in either the • The 4WD LOW position is intended for loose or 2-wheel drive position (2WD) or the 4-wheel drive Auto slippery road surfaces only.
Page 313 312 STARTING AND OPERATING WARNING! Shift Positions • You or others could be injured if you leave the The electronic transfer case switch is located on the center vehicle unattended with the transfer case in the console next to the gear selector lever. NEUTRAL position without first fully engaging the parking brake.
Page 314 STARTING AND OPERATING 313 mph (40 km/h). This position allows engine starting Rear Wheel Drive High Range - Normal street and without depressing the clutch pedal on vehicles highway driving on dry hard-surfaced roads. equipped with a manual transmission. Refer to “Clutch Interlocking Ignition System”...
Page 315 314 STARTING AND OPERATING (2WD). If the indicator light is on, the desired position light will continue to flash until all the requirements for (4WD AUTO, 4WD LOW, or NEUTRAL) has been ob- the selected position have been met. To retry a shift, move tained.
Page 316 STARTING AND OPERATING 315 Shifting can be performed with the vehicle rolling 2 to 3 Alternate Procedure mph (3 to 5 km/h) using the “Preferred Procedure” or 1. Bring the vehicle to a complete stop. completely stopped using the “Alternate Procedure.” 2.
Page 317: On-Road Driving Tips
316 STARTING AND OPERATING current transfer case position will be maintained. To They are not designed for cornering at the same speeds as retry a shift, move the 4WD Control Switch back to the conventional 2–wheel drive vehicles any more than low- original position, make certain all shift requirements slung sports cars are designed to perform satisfactorily in have been met, wait five seconds, and try the shift...
Page 318: Driving Through Water
STARTING AND OPERATING 317 entering. Proceed with caution and maintain a steady Driving Through Water Although your vehicle is capable of driving through controlled speed less than 5 mph (8 km/h) in deep water water, there are a number of precautions that must be to minimize wave effects.
Page 319: Driving In Snow, Mud And Sand
318 STARTING AND OPERATING Maintenance Hill Climbing After driving through deep water, inspect your vehicle NOTE: Before attempting to climb a hill, determine the fluids and lubricants (engine, transmission, axle, transfer conditions at the crest and/or on the other side. case) to assure they have not been contaminated.
Page 320: Traction Downhill
STARTING AND OPERATING 319 Traction Downhill WARNING! Shift the transmission into a low gear and the transfer case to 4WD LOW range. Let the vehicle go slowly down If the engine stalls or you lose headway or cannot the hill with all four wheels turning against engine make it to the top of a steep hill or grade, never compression drag.
Page 321 320 STARTING AND OPERATING • Completely inspect the underbody of your vehicle. WARNING! Check tires, body structure, steering, suspension, and exhaust system for damage. Abrasive material in any part of the brakes may cause • Check threaded fasteners for looseness, particularly on excessive wear or unpredictable braking.
Page 322: Parking Brake
STARTING AND OPERATING 321 PARKING BRAKE To set the parking brake, pull the lever up as firmly as possible. When the parking brake is applied with the ignition ON, the “Brake Warning Light” in the instru- ment cluster will light. To release the parking brake, pull up slightly, press the center button, then lower the lever completely.
Page 323 322 STARTING AND OPERATING the load on the transmission locking mechanism may WARNING! make it difficult to move the shift lever out of PARK. • Always apply the parking brake fully when leav- ing your vehicle or it may roll and cause damage or injury.
Page 324: Anti-Lock Brake System
STARTING AND OPERATING 323 When parking on a hill, turn the front wheels toward the WARNING! curb on a downhill grade and away from the curb on an uphill grade. Significant over or under-inflation of tires or mixing sizes of tires or wheels on the vehicle can lead to loss The parking brake should always be applied whenever of braking effectiveness.
Page 325 324 STARTING AND OPERATING WARNING! WARNING! • The Anti-Lock Brake System (ABS) cannot prevent Pumping of the Anti-Lock Brakes will diminish their effectiveness and may lead to an accident. Pumping the natural laws of physics from acting on the makes the stopping distance longer. Just press firmly vehicle, nor can it increase braking or steering on your brake pedal when you need to slow down or efficiency beyond that afforded by the condition...
Page 326 STARTING AND OPERATING 325 • Do not “ride” the brakes by resting your foot on the CAUTION! pedal. This could overheat the brakes and result in unpredictable braking action, longer stopping dis- The Anti-Lock Brake System (ABS) is subject to tances, or brake damage.
Page 327: Power Steering
326 STARTING AND OPERATING build up between the tire tread and the road. This NOTE: Increased noise levels at the end of the steering hydroplaning action can cause loss of traction, braking wheel travel are considered normal and do not indicate ability, and control.
Page 328: Electronic Brake Control System
STARTING AND OPERATING 327 are Hill Descent Control (HDC) and Trailer Sway Control CAUTION! (TSC). Your vehicle may be equipped with one or both of these options. Prolonged operation of the steering system at the end of the steering wheel travel will increase the steering Anti-Lock Brake System (ABS) fluid temperature and it should be avoided when This system aids the driver in maintaining vehicle control...
Page 329: Traction Control System (Tcs)
328 STARTING AND OPERATING Traction Control System (TCS) WARNING! This system monitors the amount of wheel spin of each of The Anti-Lock Brake System (ABS) cannot prevent the driven wheels. If wheel spin is detected, brake the natural laws of physics from acting on the ve- pressure is applied to the slipping wheel(s) and engine hicle, nor can it increase the traction afforded by power is reduced to provide enhanced acceleration and...
Page 330: Brake Assist System (Bas)
STARTING AND OPERATING 329 Brake Assist System (BAS) WARNING! The BAS is designed to optimize the vehicle’s braking capability during emergency braking maneuvers. The BAS (Brake Assist System) cannot prevent the natu- system detects an emergency braking situation by sens- ral laws of physics from acting on the vehicle, nor can ing the rate and amount of brake application and then it increase the traction afforded by prevailing road...
Page 331: Electronic Roll Mitigation (Erm)
330 STARTING AND OPERATING Electronic Roll Mitigation (ERM) WARNING! This system anticipates the potential for wheel lift by monitoring the driver’s steering wheel input and the Many factors, such as vehicle loading, road condi- speed of the vehicle. When ERM determines that the rate tions, and driving conditions, influence the chance of change of the steering wheel angle and vehicle’s speed that wheel lift or rollover may occur.
Page 332: Trailer Sway Control (Tsc) - If Equipped
STARTING AND OPERATING 331 Trailer Sway Control (TSC) — If Equipped WARNING! TSC uses sensors in the vehicle to recognize an exces- sively swaying trailer. TSC activates automatically once • Trailer Sway Control (TSC) cannot stop all trailers the excessively swaying trailer is recognized. When TSC from swaying.
Page 333: Hill Start Assist (Hsa)
332 STARTING AND OPERATING • For vehicles equipped with an automatic transmission, Hill Start Assist (HSA) The HSA system is designed to help the driver accelerate the HSA will work in REVERSE gear and all forward the vehicle from a complete stop while on an incline. If gears.
Page 334 STARTING AND OPERATING 333 Towing with HSA WARNING! HSA will provide assistance during acceleration on an incline while towing a trailer. There may be situations where the Hill Start Assist (HSA) will not activate and slight rolling may occur, such as on minor hills (i.e., less than 7%), or with a loaded vehicle, or while pulling a trailer.
Page 335 334 STARTING AND OPERATING WARNING! Disabling and Enabling HSA • If you use a trailer brake controller with your This feature can be turned on or turned off. To change the trailer, the trailer brakes may be activated and current setting, proceed as follows: deactivated with the brake switch.
Page 336: Hdc (Hill Descent Control) - If Equipped
STARTING AND OPERATING 335 2. Shift the transmission into PARK (automatic transmis- 10. Repeat these steps if you want to return this feature sion) or NEUTRAL (manual transmission). to its previous setting. 3. Apply the parking brake. HDC (Hill Descent Control) — If Equipped HDC is only intended for low speed off-road driving.
Page 337 336 STARTING AND OPERATING • HDC will NOT activate on level ground. NEUTRAL 3 mph (4.5 km/h) • HDC will NOT activate at vehicle speeds above 30 However, the driver can override HDC operation by mph (50 km/h). applying the brake to slow the vehicle down below the HDC control speed.
Page 338: Electronic Stability Program (Esp)
STARTING AND OPERATING 337 Enabling HDC Electronic Stability Program (ESP) Shift the transfer case into 4WD LOW range. This system enhances directional control and stability of Refer to “Four-Wheel Drive Operation” in this the vehicle under various driving conditions. ESP cor- section for transfer case operation information.
Page 339 338 STARTING AND OPERATING ESP/TCS Indicator Light WARNING! The ESP/TCS Indicator” light located in the instrument cluster, starts to flash as soon as the ESP (Electronic Stability Program) cannot prevent the tires lose traction and the ESP system becomes natural laws of physics from acting on the vehicle, active.
Page 340 STARTING AND OPERATING 339 ESP On — 2WD Vehicles and 4WD Vehicles in 2WD The “ESP OFF” button is located in the lower switch bank and 4WD High Range below the climate Control. To enter the “Partial Off” This is the normal operating mode for ESP when operat- mode, momentarily depress the “ESP OFF”...
Page 341 340 STARTING AND OPERATING mode is overcome, turn ESP back on by momentarily depressing the ESP OFF button. This may be done while the vehicle is in motion. Full Off — 4WD Vehicles in 4WD High and 4WD Low Range The “Full Off”...
Page 342: Esp/Bas Warning Light And Esp/Tcs Indicator
STARTING AND OPERATING 341 the vehicle reaches a speed of 40 mph (64 km/k). At to the PARK position and then moved out of the PARK speeds over 40 mph (64 km/k), the system automatically position. This will occur even if the message was switches to “Partial Off”...
Page 343: Tire Safety Information
342 STARTING AND OPERATING turn on when the ignition switch is turned to the ON will stop when ESP becomes inactive following the position. They should both turn off with the engine maneuver that caused the ESP activation. running. If the ESP/BAS Malfunction Indicator light TIRE SAFETY INFORMATION turns on continuously with the engine running, a mal- function has been detected in either the ESP or the BAS...
Page 344 STARTING AND OPERATING 343 standards. P-Metric tires have the letter “P” molded letters “LT” that are molded into the sidewall preced- into the sidewall preceding the size designation. Ex- ing the size designation. Example: LT235/85R16. ample: P215/65R15 95H. • Temporary spare tires are high-pressure compact •...
Page 345 344 STARTING AND OPERATING EXAMPLE: T = Temporary spare tire 31 = Overall diameter in inches (in) 215 = Section width in millimeters (mm) 65 = Aspect ratio in percent (%). — Ratio of section height to section width of tire 10.5 = Section width in inches (in) R = Construction code —...
Page 346: Tire Identification Number (Tin)
STARTING AND OPERATING 345 EXAMPLE: — The maximum speed corresponding to the speed symbol should only be achieved un- der specified operating conditions (i.e., tire pressure, vehicle loading, road conditions, and posted speed limits) Load Identification: ..blank..= Absence of any text on the sidewall of the tire indicates a Standard Load (SL) Tire Extra Load (XL) = Extra load (or reinforced) tire Light Load = Light load tire C, D, E = Load range associated with the maximum load a tire can carry at a specified pressure...
Page 347 346 STARTING AND OPERATING EXAMPLE: DOT MA L9 ABCD 0301 DOT = Department of Transportation — This symbol certifies that the tire is in compliance with the U.S. Department of Transportation tire safety standards, and is approved for highway use MA = Code representing the tire manufacturing location (two digits) L9 = Code representing the tire size (two digits) ABCD = Code used by the tire manufacturer (one to four digits)
Page 348: Tire Loading And Tire Pressure
STARTING AND OPERATING 347 Tire and Loading Information Placard Tire Loading and Tire Pressure Tire Placard Location NOTE: The proper cold tire inflation pressure is listed on either the face of the driver’s door or the driver’s side B-Pillar. Tire And Loading Information Placard This placard tells you important information about the: 1) number of people that can be carried in the vehicle...
Page 349 348 STARTING AND OPERATING occupants and cargo should never exceed XXX kg or XXX 3) tire size designed for your vehicle lbs.” on the Tire and Loading Information placard. The 4) cold tire inflation pressures for the front, rear, and combined weight of occupants, cargo/luggage and spare tires.
Page 350 STARTING AND OPERATING 349 available cargo and luggage load capacity is 650 lbs (295 NOTE: The following table shows examples on how to kg) {(since 5 x 150 = 750, and 1400 – 750 = 650 lbs (295 calculate total load, cargo/luggage, and towing capaci- kg)}.
Page 351 350 STARTING AND OPERATING WARNING! Overloading of your tires is dangerous. Overloading can cause tire failure, affect vehicle handling, and increase your stopping distance. Use tires of the...
Page 352: Tires - General Information
STARTING AND OPERATING 351 TIRES — GENERAL INFORMATION Tire Pressure Proper tire inflation pressure is essential to the safe and satisfactory operation of your vehicle. Three primary areas are affected by improper tire pressure:...
Page 353 352 STARTING AND OPERATING Safety Economy WARNING! Improper inflation pressures can cause uneven wear patterns to develop across the tire tread. These abnormal • Improperly inflated tires are dangerous and can wear patterns will reduce tread life resulting in a need for cause accidents.
Page 354: Tire Inflation Pressures
STARTING AND OPERATING 353 check tire pressure. Do not make a visual judgement Tire Inflation Pressures The proper cold tire inflation pressure is listed on either when determining proper inflation. Radial tires may look the face of the driver’s door or the driver’s side B-pillar. properly inflated even when they are underinflated.
Page 355: Tire Pressures For High Speed Operation
354 STARTING AND OPERATING Check tire pressures more often if subject to a wide range Tire Pressures For High Speed Operation of outdoor temperatures, as tire pressures vary with The manufacturer advocates driving at safe speeds temperature changes. within posted speed limits. Where speed limits or condi- tions are such that the vehicle can be driven at high Tire pressures change by approximately 1 psi (7 kPa) per speeds, maintaining correct tire inflation pressure is very...
Page 356: Radial-Ply Tires
STARTING AND OPERATING 355 Tire Spinning When stuck in mud, sand, snow, or ice conditions, do not Radial-Ply Tires spin your vehicle’s wheels above 35 mph (55 km/h). WARNING! WARNING! Combining radial ply tires with other types of tires Fast spinning tires can be dangerous. Forces gener- on your vehicle will cause your vehicle to handle ated by excessive wheel speeds may cause tire dam- poorly.
Page 357: Tread Wear Indicators
356 STARTING AND OPERATING Tread Wear Indicators becomes 1/16 in (2 mm). When the indicators appear in Tread wear indicators are in the original equipment tires two or more adjacent grooves, the tire should be re- to help you in determining when your tires should be placed.
Page 358: Replacement Tires
STARTING AND OPERATING 357 “Tread Wear Indicators”). Refer to the “Tire and Loading WARNING! Information” placard for the size designation of your tires. The service description and load identification will Tires and the spare tire should be replaced after six be found on the original equipment tire.
Page 359: Alignment And Balance
358 STARTING AND OPERATING WARNING! CAUTION! • Do not use a tire, wheel size or rating other than that specified for your vehicle. Some combinations Replacing original tires with tires of a different size of unapproved tires and wheels may change sus- may result in false speedometer and odometer pension dimensions and performance characteris- readings.
Page 360: Tire Chains
STARTING AND OPERATING 359 Improper alignment will not cause vehicle vibration. Vibration may be a result of tire and wheel out-of- balance. Proper balancing will reduce vibration and avoid tire cupping and spotty wear. TIRE CHAINS Use only compact chains, or other traction aids that meet SAE type “Class S”...
Page 361: Tire Rotation Recommendations
360 STARTING AND OPERATING CAUTION! These cautions apply to all chain traction devices, includ- To avoid damage to your vehicle, tires, or chains, ing link and cable (radial) chains. observe the following precautions: TIRE ROTATION RECOMMENDATIONS • Do not use tire chains on vehicles equipped with Tires on the front and rear axles of vehicles operate at tires other than P235/65R17 or smaller tires.
Page 362: Tire Pressure Monitor System (Tpms) - If Equipped
STARTING AND OPERATING 361 Remember, more frequent rotation is permissible if de- TIRE PRESSURE MONITOR SYSTEM (TPMS) — IF sired. Also, correct for anything causing rapid or unusual EQUIPPED wear prior to performing the tire rotation. • The Tire Pressure Monitor System (TPMS) will warn The suggested rotation method is the “forward-cross”...
Page 363 362 STARTING AND OPERATING The tire pressure will also increase as the vehicle is may need to be driven for up to 10 minutes above 15 driven. This is normal and there should be no adjust- mph (25 km/h) in order for the TPMS to receive this ment for this increased pressure.
Page 364 STARTING AND OPERATING 363 CAUTION! NOTE: • The TPMS has been optimized for the original • The TPMS is not intended to replace normal tire care equipment tires and wheels. TPMS pressures and and maintenance, or to provide warning of a tire warning have been established for the tire size failure or condition.
Page 365: Base System - If Equipped
364 STARTING AND OPERATING • Four Tire Pressure Monitoring Sensors gauge, even if under-inflation has not reached the level to trigger illumination of the Tire Pressure Moni- • Tire Pressure Monitoring Telltale light toring Telltale light. The matching full-size spare wheel and tire assembly (if •...
Page 366 STARTING AND OPERATING 365 value. Once the system receives the updated tire pres- 2. Installing some form of aftermarket window tinting sures, the system will automatically update and the Tire that affects radio wave signals. Pressure Monitoring Telltale light will turn off. The 3.
Page 367: Premium System - If Equipped
366 STARTING AND OPERATING 3. Driving the vehicle for up to 10 minutes above 15 mph 4. For each subsequent ignition key cycle, a chime will (25 km/h) will turn off the TPMS Telltale light, as long as sound and the TPMS Telltale light will flash on and off no tire pressure is below the low-pressure warning limit for 75 seconds and then remain on solid.
Page 368 STARTING AND OPERATING 367 NOTE: It is particularly important for you to check the limit will not cause the Tire Pressure Monitoring Telltale tire pressure in all of the tires on your vehicle monthly light to illuminate or the chime to sound. However, it will and to maintain the proper pressure.
Page 369 368 STARTING AND OPERATING turn off. The vehicle may need to be driven for up to 10 minutes above 15 mph (25 km/h) in order for the TPMS to receive this information. Check TPMS Warning When a system fault is detected, the Tire Pressure Moni- toring Telltale light will flash on and off for 75 seconds and then remain on solid.
Page 370 STARTING AND OPERATING 369 1. Jamming due to electronic devices or driving next to facilities emitting the same radio frequencies as the TPMS sensors. 2. Installing some form of aftermarket window tinting that affects radio wave signals. 3. Lots of snow or ice around the wheels or wheel housings.
Page 371 370 STARTING AND OPERATING a chime will sound and the TPMS Telltale light will turn 2. If you install the compact spare tire in place of a road on upon the next ignition key cycle. In addition, the EVIC tire that has a pressure below the low-pressure warning will display a Low Pressure message and a graphic limit, upon the next ignition key cycle, the TPMS Telltale showing the low tire pressure value flashing.
Page 372: General Information
STARTING AND OPERATING 371 5. Once you repair or replace the original road tire and The tire pressure sensors are covered under one of the reinstall it on the vehicle in place of the compact spare, following licenses: the TPMS will update automatically. In addition, the TPMS Telltale light will turn off and the graphic in the United States .
Page 373: Reformulated Gasoline
372 STARTING AND OPERATING high speeds can cause damage and immediate service is The manufacturer supports the use of reformulated gaso- required. Poor quality gasoline can cause problems such lines. Properly blended reformulated gasolines will pro- as hard starting, stalling, and hesitations. If you experi- vide excellent performance and durability of engine and ence these symptoms, try another brand of gasoline fuel system components.
Page 374: Mmt In Gasoline
STARTING AND OPERATING 373 Problems that result from using methanol/gasoline or MMT can be used at levels higher than those allowed in E85 Ethanol blends are not the responsibility of the the United States. MMT is prohibited in Federal and manufacturer.
Page 375: Carbon Monoxide Warnings
374 STARTING AND OPERATING • The use of leaded gas is prohibited by Federal law. Carbon Monoxide Warnings Using leaded gasoline can impair engine performance, WARNING! and damage the emission control system. • An out-of-tune engine, or certain fuel or ignition Carbon monoxide (CO) in exhaust gases is deadly.
Page 376: Adding Fuel
STARTING AND OPERATING 375 the vehicle is raised. Have any abnormal conditions repaired promptly. Until repaired, drive with all side windows fully open. • Keep the trunk closed when driving your vehicle to prevent carbon monoxide and other poisonous ex- haust gases from entering the vehicle.
Page 377 376 STARTING AND OPERATING CAUTION! WARNING! • Damage to the fuel system or emission control • Never have any smoking materials lit in or near system could result from using an improper fuel the vehicle when the gas cap is removed or the tank filler tube cap (gas cap).
Page 378: Loose Fuel Filler Cap Message
STARTING AND OPERATING 377 on if the gas cap is not secured properly. Make sure VEHICLE LOADING that the gas cap is tightened each time the vehicle is Certification Label refueled. As required by National Highway Traffic Safety Admin- • When the fuel nozzle “clicks” or shuts off, the fuel istration regulations, your vehicle has a certification label tank is full.
Page 379 378 STARTING AND OPERATING tongue weight, and cargo. The label also specifies maxi- Tire Size mum capacities of front and rear axle systems (GAWR). The tire size on the label represents the actual tire size on Total load must be limited, so GVWR, and front and rear your vehicle.
Page 380 STARTING AND OPERATING 379 Loading Improper weight distributions can have an adverse affect The actual total weight and the weight of the front and on the way your vehicle steers and handles, and the way rear of your vehicle at the ground can best be determined the brakes operate.
Page 381: Trailer Towing
380 STARTING AND OPERATING TRAILER TOWING Gross Trailer Weight (GTW) In this section, you will find safety tips and information The Gross Trailer Weight (GTW) is the weight of the on limits to the type of towing you can reasonably do trailer plus the weight of all cargo, consumables, and with your vehicle.
Page 382 STARTING AND OPERATING 381 Gross Combination Weight Rating (GCWR) Tongue Weight (TW) The Gross Combination Weight Rating (GCWR) is the Tongue weight (TW) is the downward force exerted on total permissible weight of your vehicle and trailer when the hitch ball by the trailer. In most cases, it should not be weighed in combination.
Page 383 382 STARTING AND OPERATING Weight-Carrying Hitch equalizing) hitch are recommended for heavier Tongue A weight-carrying hitch supports the trailer tongue Weights (TW) and may be required depending on Vehicle weight, just as if it were luggage located at a hitch ball or and Trailer configuration/loading to comply with Gross some other connecting point of the vehicle.
Page 384: Trailer Hitch Classification
STARTING AND OPERATING 383 Weight Distributing Hitch System Improper Adjustment of Weight Distributing System Trailer Hitch Classification Your vehicle is capable of towing trailers up to 2,000 lbs (907 kg) without added equipment or alterations to the standard equipment. Your vehicle may be factory equipped for safe towing of trailers weighing over 2,000...
Page 385: Trailer Towing Weights
384 STARTING AND OPERATING lbs (907 kg) with the optional Trailer Tow Prep Package. Trailer Hitch Classification See your authorized dealer for package content. Class II - Medium 3,500 lbs (1 587 kg) Duty The following chart provides the industry standard for Class III - Heavy Duty 5,000 lbs (2 268 kg) the maximum trailer weight a given trailer hitch class can...
Page 386 STARTING AND OPERATING 385 3.7L/6-Speed 40 sq ft (3.72 sq m) 3,500 lbs (1 587 kg) 350 lbs (159 kg) Manual 3.7L/Automatic 32 sq ft (2.97 sq m) 2,000 lbs (907 kg) 200 lbs (91 kg) 3.7L/Automatic 32 sq ft (2.97 sq m) 2,000 lbs (907 kg) 200 lbs (91 kg) 3.7L/Automatic...
Page 387: Trailer And Tongue Weight
386 STARTING AND OPERATING 3.7L/Automatic 64 sq ft (5.94 sq m) 5,000 lbs (2 268 kg) 500 lbs (227 kg) w/ Cooler 3.7L/Automatic 64 sq ft (5.94 sq m) 5,000 lbs (2 268 kg) 500 lbs (227 kg) w/Cooler Refer to local laws for maximum trailer towing speeds. NOTE: The trailer tongue weight must be considered as which will cause loss of control of vehicle and trailer.
Page 388: Towing Requirements
STARTING AND OPERATING 387 NOTE: Remember that everything put into or on the trailer adds to the load on your vehicle. Also, additional factory-installed options, or authorized dealer-installed options, must be considered as part of the total load on your vehicle. Refer to the “Tire and Loading Information” placard for the maximum combined weight of occupants and cargo for your vehicle.
Page 389 388 STARTING AND OPERATING CAUTION! WARNING! • Avoid towing a trailer for the first 500 mi (805 km) Improper towing can lead to an injury accident. of vehicle operation. Doing so may damage your Follow these guidelines to make your trailer towing vehicle.
Page 390 STARTING AND OPERATING 389 • Safety chains must always be used between your 3. GAWR vehicle and trailer. Always connect the chains to the 4. Tongue weight rating for the trailer hitch utilized frame or hook retainers of the vehicle hitch. Cross the (This requirement may limit the ability to always chains under the trailer tongue and allow enough achieve the 10% to 15% range of tongue weight as a...
Page 391 390 STARTING AND OPERATING − Check for signs of tire wear or visible tire damage actuated brakes. When towing a trailer equipped with before towing a trailer. Refer to “Tires–General Infor- a hydraulic surge actuated brake system, an electronic mation” in this section for information on tread wear brake controller is not required.
Page 392 STARTING AND OPERATING 391 The Trailer Tow Package may include a 4- and 7- pin WARNING! wiring harness. Use a factory approved trailer harness and connector. Do not connect trailer brakes to your vehicle’s hy- draulic brake lines. It can overload your brake sys- NOTE: Do not cut or splice wiring into the vehicles tem and cause it to fail.
Page 393: Towing Tips
392 STARTING AND OPERATING 4 - Pin Connector 7- Pin Connector Towing Tips Before setting out on a trip, practice turning, stopping, and backing the trailer in an area located away from heavy traffic.
Page 394 STARTING AND OPERATING 393 If using a manual transmission vehicle for trailer towing, interval specified for “police, taxi, fleet, or frequent trailer all starts must be in FIRST gear to avoid excessive clutch towing” in the “Maintenance Schedule” in this manual. slippage.
Page 395: Recreational Towing (Behind Motorhome, Etc.)
394 STARTING AND OPERATING Towing Tips — Cooling System RECREATIONAL TOWING (BEHIND To reduce potential for engine and transmission over- MOTORHOME, ETC.) heating, take the following actions: Towing — 2WD Models Recreational towing is not allowed. − City Driving When stopped for short periods of time, put transmission CAUTION! in NEURAL and increase engine idle speed.
Page 396 STARTING AND OPERATING 395 CAUTION! WARNING! • The Automatic Transmission must be in PARK position for recreational towing. The Manual You or others could be injured if you leave the Transmission (if equipped) must be in gear (for vehicle unattended with the transfer case in the example, 4th gear) for recreational towing.
Page 397 396 STARTING AND OPERATING 2. Shut OFF the engine. 10. Repeat Steps 8 and 9 with the transmission in DRIVE (automatic transmission) or 1st gear (manual transmis- 3. Turn the ignition switch to the ON position. sion). 4. Depress the brake pedal. 11.
Page 398 STARTING AND OPERATING 397 indicator light will flash continuously until all require- ments are met or until the NEUTRAL button is re- Shifting Out of NEUTRAL leased. Perform the following procedure to prepare your vehicle • The ignition switch must be in the ON position for a for normal usage: shift to take place and for the position indicator lights 1.
Page 399 398 STARTING AND OPERATING 7. Use the point of a ballpoint pen or similar object to depressing the NEUTRAL selection button or while depress the recessed transfer case NEUTRAL button. the shift attempt is in process, then all of the mode Release the NEUTRAL button after the NEUTRAL indi- position indicator lights will flash continuously until cator light turns off (approximately one second).
Page 400: What To Do In Emergencies
WHAT TO DO IN EMERGENCIES CONTENTS ▫ Spare Tire Removal ....402 Hazard Warning Flasher ....400 ▫...
Page 401: Hazard Warning Flasher
400 WHAT TO DO IN EMERGENCIES HAZARD WARNING FLASHER NOTE: With extended use, the Hazard Warning Flash- The Hazard Flasher switch is located in the switch bank ers may wear down your battery. below the Climate Controls. IF YOUR ENGINE OVERHEATS Push and release the switch to turn on the Hazard In any of the following situations, you can reduce the Warning Flashers.
Page 402: Jacking And Tire Changing
WHAT TO DO IN EMERGENCIES 401 the fan control to HIGH. This allows the heater core to act JACKING AND TIRE CHANGING as a supplement to the radiator and aids in removing heat WARNING! from the engine cooling system. • Getting under a jacked-up vehicle is dangerous. CAUTION! The vehicle could slip off the jack and fall on you.
Page 403: Jack Location
402 WHAT TO DO IN EMERGENCIES Jack Location Spare Tire Stowage The scissor-type jack and tire changing tools are located The spare tire is stowed underneath the rear of the in the cargo compartment behind a trim cover on the left vehicle and is held in place by a cable winch mechanism.
Page 404: Preparations For Jacking
WHAT TO DO IN EMERGENCIES 403 When the spare is clear, tilt the retainer at the end of the cable, and pull it through the center of the wheel. Preparations For Jacking • Park the vehicle on a firm level surface as far from the edge of the roadway as possible.
Page 405 404 WHAT TO DO IN EMERGENCIES WARNING! Do not attempt to change a tire on the side of the vehicle close to moving traffic. Pull far enough off the road to avoid being hit when operating the jack or changing the wheel. •...
Page 406: Jacking Instructions
WHAT TO DO IN EMERGENCIES 405 Jacking Instructions 1. Remove spare tire. 2. Remove jack and tools from mounting bracket. As- semble the tools by connecting the driver to the exten- sion, and then to the lug wrench. 3. Loosen (but do not remove) the wheel lug nuts by Jack Warning Label turning them to the left one turn while the wheel is still WARNING!
Page 407 406 WHAT TO DO IN EMERGENCIES Front Jacking Location Rear Jacking Location 5. Raise the vehicle by turning the jack screw to the right. Raise the vehicle only until the tire just clears the surface and enough clearance is obtained to install the spare tire. Minimum tire lift provides maximum stability.
Page 408 WHAT TO DO IN EMERGENCIES 407 nuts until each nut has been tightened twice. Correct WARNING! wheel nut tightness is 95 ft lb (130 N·m). If in doubt about the correct tightness, have them checked with a torque Raising the vehicle higher than necessary can make wrench by your authorized dealer or at a service station.
Page 409: Jump-Starting
408 WHAT TO DO IN EMERGENCIES JUMP–STARTING 1. Wear eye protection and remove all metal jewelry such WARNING! as watchbands or bracelets that might make an unin- tended electrical contact. • Take care to avoid the radiator cooling fan when- ever the hood is raised.
Page 410 WHAT TO DO IN EMERGENCIES 409 4. Turn off the heater, radio and all unnecessary electrical WARNING! loads. • You should not try to start your vehicle by pushing 5. Connect one end of the jumper cable to the positive or towing.
Page 411: Towing A Disabled Vehicle
410 WHAT TO DO IN EMERGENCIES 8. Start the engine in the vehicle that has the booster TOWING A DISABLED VEHICLE battery, let the engine idle a few minutes, and then start Proper towing or lifting equipment is required to prevent the engine in the vehicle with the discharged battery.
Page 412 WHAT TO DO IN EMERGENCIES 411 TOWING METHOD NOTE: The transmission and transfer case must be in NEUTRAL under any towing configuration. Model Flat Towing (all four wheels on the ground) Flat Bed Tow mph (48 km/ and/or when wheels suspe 2 Wheel Drive Rear driveshaft removed All four whee...
Page 414: Maintaining Your Vehicle
MAINTAINING YOUR VEHICLE CONTENTS ▫ Drive Belts — Check Condition And Tension . . 424 Engine Compartment — 3.7L ....416 ▫ Spark Plugs ......424 Onboard Diagnostic System —...
Page 415 414 MAINTAINING YOUR VEHICLE ▫ Power Steering — Fluid Check ... . 430 ▫ Manual Transmission — If Equipped ..444 ▫ Driveline And Steering Component Lubrication 431 ▫...
Page 416 MAINTAINING YOUR VEHICLE 415 ▫ Headlight ......461 Fluids, Lubricants, And Genuine Parts ..464 ▫...
Page 417: Engine Compartment - 3.7L
416 MAINTAINING YOUR VEHICLE ENGINE COMPARTMENT — 3.7L 3.7L ENGINE COMPT LHD...
Page 418: Onboard Diagnostic System - Obd Ii
MAINTAINING YOUR VEHICLE 417 ONBOARD DIAGNOSTIC SYSTEM — OBD II CAUTION! Your vehicle is equipped with a sophisticated Onboard Diagnostic system called OBD II. This system monitors • Prolonged driving with the MIL on could cause the performance of the emissions, engine, and automatic further damage to the emission control system.
Page 419: Emissions Inspection And Maintenance Programs
418 MAINTAINING YOUR VEHICLE the message. If the problem persists, the message will serviced, recently had a dead battery, or a battery replace- appear the next time the vehicle is started. This might ment. If the OBD II system should be determined not indicate a damaged cap.
Page 420: Replacement Parts
MAINTAINING YOUR VEHICLE 419 5. Approximately 15 seconds later, one of two things will system to update. A recheck with the above test routine happen: may then indicate that the system is now ready. a. The MIL will flash for about 10 seconds and then Regardless of whether your vehicle’s OBD II system is return to being fully illuminated until you turn OFF ready or not ready, if the MIL is illuminated during...
Page 421: Authorized Dealer Service
420 MAINTAINING YOUR VEHICLE AUTHORIZED DEALER SERVICE WARNING! Your authorized dealer has the qualified service person- nel, special tools, and equipment to perform all service You can be badly injured working on or around a operations in an expert manner. Service manuals are motor vehicle.
Page 422: Engine Oil
MAINTAINING YOUR VEHICLE 421 These items should be inspected if a malfunction is observed or suspected. Engine Oil Checking Oil Level To assure proper engine lubrication, the engine oil must be maintained at the correct level. The best time to check the engine oil level is about five minutes after a fully warmed up engine is shut off or before starting the engine after it has sat overnight.
Page 423 422 MAINTAINING YOUR VEHICLE Engine Oil Selection CAUTION! For best performance and maximum protection under all types of operating conditions, the manufacturer recom- Do not overfill the engine oil. Overfilling the engine mends engine oils that are API Certified and meet the oil will cause oil aeration, which can lead to loss of requirements of DaimlerChrysler Material Standard MS- oil pressure and an increase in oil temperature.
Page 424 MAINTAINING YOUR VEHICLE 423 Engine Oil Viscosity Materials Added to Engine Oil SAE 5W-20 engine oil is recommended for all operating The manufacturer strongly recommends against the ad- temperatures. This engine oil improves low temperature dition of any additives (other than leak detection dyes) to starting and vehicle fuel economy.
Page 425: Engine Oil Filter
424 MAINTAINING YOUR VEHICLE Engine Oil Filter Inspect belts for evidence of cuts, cracks, glazing, or The engine oil filter should be replaced at every engine frayed cords and replaced if there is indication of dam- oil change. age, which could result in belt failure. Also, check belt routing to make sure there is no interference between the Engine Oil Filter Selection belts and other engine components.
Page 426: Engine Air Cleaner Filter
MAINTAINING YOUR VEHICLE 425 Engine Air Cleaner Filter Fuel Filter Refer to the “Maintenance Schedule” in Section 8 of this A plugged fuel filter can cause stalling, limit the speed at manual for engine air cleaner filter maintenance inter- which a vehicle can be driven or cause hard starting. vals.
Page 427 426 MAINTAINING YOUR VEHICLE CAUTION! WARNING! Damage to the catalytic converter can result if your A hot exhaust system can start a fire if you park over vehicle is not kept in proper operating condition. In materials that can burn. Such materials might be the event of engine malfunction, particularly involv- grass or leaves coming into contact with your exhaust ing engine misfire or other apparent loss of perfor-...
Page 428: Crankcase Emission Control System
MAINTAINING YOUR VEHICLE 427 • Do not shut off the engine or interrupt the ignition accumulate deposits. If a valve is not working properly, when the transmission is in gear and the vehicle is in replace it with a new valve. Do not attempt to clean the motion.
Page 429 428 MAINTAINING YOUR VEHICLE WARNING! CAUTION! • Battery fluid is a corrosive acid solution and can • It is essential when replacing the cables on the burn or even blind you. Don’t allow battery fluid battery that the positive cable is attached to the to contact your eyes, skin, or clothing.
Page 430: Air Conditioner Maintenance
MAINTAINING YOUR VEHICLE 429 Air Conditioner Maintenance WARNING! For best possible performance, your air conditioner should be checked and serviced by an authorized dealer • Use only refrigerants and compressor lubricants at the start of each warm season. This service should approved by the manufacturer for your air condi- include cleaning of the condenser fins and a performance tioning system.
Page 431: A/C Air Filter - If Equipped
430 MAINTAINING YOUR VEHICLE Refrigerant Recovery and Recycling R-134a Air Conditioning Refrigerant is a hydrofluorocar- Power Steering — Fluid Check bon (HFC) that is endorsed by the Environmental Pro- Checking the power steering fluid level at a defined tection Agency and is an ozone-saving product. How- service interval is not required.
Page 432: Driveline And Steering Component Lubrication
MAINTAINING YOUR VEHICLE 431 If necessary, add fluid to restore to the proper indicated wiped clean to remove dust and grit; after lubricating level. With a clean cloth, wipe any spilled fluid from all excess oil and grease should be removed. Particular surfaces.
Page 433: Windshield And Rear Window Washers
432 MAINTAINING YOUR VEHICLE Operation of the wipers on dry glass for long periods Windshield and Rear Window Washers may cause deterioration of the wiper blades. Always use The windshield and rear window washers share the same washer fluid when using the wipers to remove salt or dirt fluid reservoir.
Page 434: Exhaust System
MAINTAINING YOUR VEHICLE 433 fumes to seep into the passenger compartment. In addi- WARNING! tion, inspect the exhaust system each time the vehicle is raised for lubrication or oil change. Replace as required. Commercially available windshield washer solvents are flammable. They could ignite and burn you. Care WARNING! must be exercised when filling or working around the washer solution.
Page 435: Cooling System
434 MAINTAINING YOUR VEHICLE Cooling System Coolant Checks Check engine coolant (antifreeze) protection every 12 WARNING! months (before the onset of freezing weather, where applicable). If coolant is dirty or rusty in appearance, the • When working near the radiator cooling fan, dis- system should be drained, flushed, and refilled with connect the fan motor lead or turn the ignition fresh coolant.
Page 436 MAINTAINING YOUR VEHICLE 435 properly, the coolant will begin to drain from the coolant CAUTION! recovery bottle. DO NOT REMOVE THE COOLANT PRESSURE CAP WHEN THE COOLING SYSTEM IS • Mixing of coolants other than specified HOAT HOT. engine coolants, may result in engine damage and may decrease corrosion protection.
Page 437 436 MAINTAINING YOUR VEHICLE • Use only high purity water such as distilled or deion- Adding Coolant Your vehicle has been built with an improved engine ized water when mixing the water/engine coolant coolant that allows extended maintenance intervals. This solution.
Page 438 MAINTAINING YOUR VEHICLE 437 The cap should be inspected and cleaned if there is any Disposal of Used Coolant accumulation of foreign material on the sealing surfaces. Used ethylene glycol based engine coolant is a regulated substance requiring proper disposal. Check with your WARNING! local authorities to determine the disposal rules for your community.
Page 439 438 MAINTAINING YOUR VEHICLE • Do not overfill the coolant bottle. service attendant of this. As long as the engine operating temperature is satisfactory, the coolant bottle need only • Check coolant freeze point in the radiator and in the be checked once a month.
Page 440: Hoses And Vacuum/Vapor Harnesses
MAINTAINING YOUR VEHICLE 439 • Keep the front of the radiator clean. If your vehicle is Ensure nylon tubing in these areas has not melted or equipped with air conditioning, keep the front of the collapsed. condenser clean, also. Inspect all hose connections such as clamps and cou- •...
Page 441: Brake System
440 MAINTAINING YOUR VEHICLE Brake System brittle rubber, cracking, tears, cuts, abrasions, and exces- In order to assure brake system performance, all brake sive swelling suggest deterioration of the rubber. Particu- system components should be inspected periodically. lar attention should be made to examining those hose Suggested service intervals can be found in the “Mainte- surfaces nearest to high heat sources, such as the exhaust nance Schedule”...
Page 442 MAINTAINING YOUR VEHICLE 441 • Inspect the brake hoses whenever the brake system is Check the fluid level in the master cylinder when per- serviced and at every engine oil change. Inspect hy- forming underhood services. draulic brake hoses for surface cracking, scuffing, or Clean the top of the master cylinder area before removing worn spots.
Page 443: Clutch Hydraulic System - Manual Transmission (If Equipped)
442 MAINTAINING YOUR VEHICLE WARNING! CAUTION! • Overfilling the brake fluid reservoir can result in Do not allow petroleum-base fluid to contaminate spilling brake fluid on hot engine parts and the the brake fluid. Seal damage may result. brake fluid catching fire. •...
Page 444: Automatic Transmission
MAINTAINING YOUR VEHICLE 443 Fluid and Filter Changes Automatic Transmission Change the automatic transmission fluid and filter at the Fluid Level Check intervals shown in the “Maintenance Schedule” in Sec- Your vehicle is equipped with a capped dipstick tube that tion 8 of this manual.
Page 445: Manual Transmission - If Equipped
444 MAINTAINING YOUR VEHICLE Manual Transmission — If Equipped NOTE: Be sure to follow the “trailer tow, snow plow, heavy load, taxi, police, commercial service, off-road, Fluid Level Check desert, or sustained high speeds during hot weather” Check the fluid level by removing the fill plug. The fluid maintenance interval if applicable.
Page 446 MAINTAINING YOUR VEHICLE 445 Draining Fluid First remove fill plug (2), then drain plug (3). Recom- mended tightening torque for drain and fill plugs is 15–25 ft lbs (20–34 N·m). CAUTION! Do not over-tighten the plugs. You could damage them and cause a leak. Lubricant Selection Use only manufacturer’s recommended fluid.
Page 447: Front/Rear Axle Fluid
446 MAINTAINING YOUR VEHICLE the vehicle. Fluid changes are not necessary unless the Frequency of Fluid Change fluid becomes contaminated with water. Change the fluid Under normal operating conditions, the lubricant in- immediately if contaminated with water. stalled at the factory will give satisfactory lubrication for the life of the vehicle.
Page 448 MAINTAINING YOUR VEHICLE 447 • Atmospheric fallout/industrial pollutants. road surfaces on which the vehicle is operated, extreme hot or cold weather and other extreme conditions will • Bird droppings. have an adverse effect on paint, metal trim, and under- body protection. Washing •...
Page 449 448 MAINTAINING YOUR VEHICLE • If you detect any stone chips or scratches in the paint, CAUTION! touch them up immediately. The cost of such repairs is considered the responsibility of the owner. • Do not use abrasive or strong cleaning materials •...
Page 450 MAINTAINING YOUR VEHICLE 449 Wheel and Wheel Trim Care use protectants or other products, which may cause All wheels and wheel trim, especially aluminum and undesirable reflections. Use soap and warm water to chrome plated wheels should be cleaned regularly with restore the low glare surface.
Page 451 450 MAINTAINING YOUR VEHICLE • For tough stains, apply Mopar Total Clean or a mild use polishes, oils, cleaning fluids, solvents, detergents, or ammonia-based cleaners to clean leather upholstery. Ap- soap solution to a clean damp cloth and remove the plication of a leather conditioner is not required to stain.
Page 452 MAINTAINING YOUR VEHICLE 451 To minimize the possibility of scratching the lenses and Cleaning Plastic Instrument Cluster Lenses reducing light output, avoid wiping with a dry cloth. To The lenses in front of the instruments in this vehicle are remove road dirt, wash with a mild soap solution fol- molded in clear plastic.
Page 453: Sky Slider Top Care
452 MAINTAINING YOUR VEHICLE Replace the seat belts if they appear frayed or worn or if the buckles do not work properly. General Cleaning Careful vacuuming of the top before washing is helpful SKY SLIDER TOP CARE in removing dust and other foreign particles. Immediate removal of any contaminant is recommended.
Page 454: Additional Cleaning Procedure
MAINTAINING YOUR VEHICLE 453 • Allow the top to dry before opening. Vacuuming the Additional Cleaning Procedure top with a wet/dry shop vacuum will decrease the For additional cleaning assistance in removing stubborn tops drying time, ensure removal of all dirt, and delete stains, apply Mopar Convertible Cloth Top Cleaner to streaks in the material.
Page 455: Weather Strip Care
454 MAINTAINING YOUR VEHICLE CAUTION! Avoid getting Scotchguard on the surrounding weather strips, moldings, paint, or glass. Damage to these items might occur. Weather Strip Care Lubricate the weather strips periodically with Mopar Weather Strip Lubricant, to keep them soft and pliable. FUSES (INTEGRATED POWER MODULE) The Totally Integrated Power Module (TIPM) is located Totally Integrated Power Module (TIPM)
Page 456 MAINTAINING YOUR VEHICLE 455 Cavity Cartridge Mini- Description Cavity Cartridge Mini- Description Fuse Fuse Fuse Fuse 40 Amp — Rear Door Modules — — — Green 60 Amp — Ignition Off Draw 25 Amp — Driver Door Node Yellow (IOD) White 40 Amp —...
Page 457 456 MAINTAINING YOUR VEHICLE Cavity Cartridge Mini- Description Cavity Cartridge Mini- Description Fuse Fuse Fuse Fuse 20 Amp — Front Washer/Rear — 20 Amp Power Outlet #1 (ci- Blue Washer - if equipped Yellow gar lighter)/Rain Sen- sor - if equipped/ 25 Amp —...
Page 458 MAINTAINING YOUR VEHICLE 457 Cavity Cartridge Mini- Description Cavity Cartridge Mini- Description Fuse Fuse Fuse Fuse — 10 Amp Automatic Tempera- — 20 Amp Multifunction Control ture Control (ATC) - Yellow Switch/Cabin Com- if equipped partment Node (CCN)/Steering Col- — 30 Amp Radio/Amplifier - if umn Control Module...
Page 459 458 MAINTAINING YOUR VEHICLE Cavity Cartridge Mini- Description Cavity Cartridge Mini- Description Fuse Fuse Fuse Fuse — 15 Amp Exterior Lighting — — 15 Amp Interior Lighting/ Blue Left Front Park and Blue Steering Wheel Side Marker, Left Tail Switches - if and Running, License equipped/Switch Lights...
Page 460 MAINTAINING YOUR VEHICLE 459 Cavity Cartridge Mini- Description Cavity Cartridge Mini- Description Fuse Fuse Fuse Fuse — 10 Amp Power Mirror Switch/ — 10 Amp Occupant Restraint Driver Window Controller (ORC) Switch — 10 Amp Powertrain Control — 10 Amp Ignition Switch/ Module (PCM) Wireless Control...
Page 461 460 MAINTAINING YOUR VEHICLE Cavity Cartridge Mini- Description CAUTION! Fuse Fuse • When installing the Integrated Power Module — 10 Amp Anti-Lock Brake Sys- tem (ABS)/Electronic cover, it is important to ensure the cover is prop- Stability Program erly positioned and fully latched. Failure to do so (ESP) Module/Stop may allow water to get into the Integrated Power Light Switch...
Page 462: Replacement Light Bulbs
MAINTAINING YOUR VEHICLE 461 REPLACEMENT LIGHT BULBS BULB REPLACEMENT Headlight LIGHT BULBS — Interior Bulb No. 1. Open the hood. Cargo Light ......WL212–2 Overhead Console Light.
Page 463: Front Fog Light
462 MAINTAINING YOUR VEHICLE 2. Remove three push-pins from the wheel-well liner. CAUTION! 3. Gently flex the wheel-well liner forward to access the Do not touch the new bulb with your fingers. Oil bulb. contamination will severely shorten bulb life. If the 4.
Page 464 MAINTAINING YOUR VEHICLE 463 3. Rotate the bulb’s socket counterclockwise, and remove Rear Tail/Stop, Turn Signal, and Back-Up Lights the bulb and socket assembly from the fog light housing. 1. Open the liftgate. 4. Pull the bulb out of the socket and insert the replace- 2.
Page 465: Fluids, Lubricants, And Genuine Parts
464 MAINTAINING YOUR VEHICLE 10. Install the taillight housing and screws. FLUID CAPACITIES 11. Close the liftgate. U.S. Metric Fuel (approximate) 3.7 Liter Engine 19.5 Gal 73.8 L Engine Oil-With Filter SAE 5W-20, API Certified 5 Qts 4.7 L Cooling System * Mopar Antifreeze/Coolant 5 Year/100,000 Mile Formula or equiva- 14 Qts 13.2 L...
Page 466: Chassis
MAINTAINING YOUR VEHICLE 465 Component Fluids, Lubricants, and Genuine Parts Engine Oil Use API Certified SAE 5W-20 Engine Oil meeting the requirements of DaimlerChrysler Material Standard MS-6395. Refer to the engine oil fill cap for correct SAE grade. Spark Plugs ZFR6F-11 (Gap.043 in [1.1 mm]) Oil Filter Mopar 5281090 or equivalent.
Page 467 466 MAINTAINING YOUR VEHICLE Component Fluids, Lubricants, and Genuine Parts Brake Master Cylinder/Manual Mopar DOT 3, SAE J1703 or equivalent should be used. If DOT 3 brake Transmission Clutch System fluid is not available, then DOT 4 is acceptable. Use only recommended brake fluids.
Page 468 MAINTENANCE SCHEDULES CONTENTS ▫ Required Maintenance Intervals ... 470 Emissions Control System Maintenance ..468 Maintenance Schedule ....468...
Page 469 468 MAINTENANCE SCHEDULES EMISSIONS CONTROL SYSTEM MAINTENANCE MAINTENANCE SCHEDULE The Scheduled Maintenance services listed in bold type The oil change indicator system will remind you that it is must be done at the times or mileages specified to ensure time to take your vehicle in for scheduled maintenance. the continued proper functioning of the emission control On Electronic Vehicle Information Center (EVIC) system.
Page 470 MAINTENANCE SCHEDULES 469 if it has been six months since your last oil change even At Each Stop for Fuel if the oil change indicator message is NOT illumi- • Check the engine oil level about five minutes after a nated.
Page 471 470 MAINTENANCE SCHEDULES • Check all lights and other electrical items for correct Required Maintenance Intervals operation. At Each Oil Change • Change the engine oil filter. • Inspect the brake hoses and lines. • Check the manual transmission fluid level. CAUTION! Failure to perform the required maintenance items may result in damage to the vehicle.
Page 472 MAINTENANCE SCHEDULES 471 Perform Maintenance Every (Where time and mileage are listed, follow the interval that occurs first.) Maintenance Items Miles Kilometers or Months Change the engine oil and engine oil filter. 6,000 10 000 Rotate the tires. 6,000 10 000 If using your vehicle in dusty or off-road conditions, inspect the engine air cleaner filter, and replace if 12,000...
Page 473 472 MAINTENANCE SCHEDULES Perform Maintenance Every (Where time and mileage are listed, follow the interval that occurs first.) Maintenance Items Miles Kilometers or Months Inspect the front suspension, tie rod ends and boot 24,000 40 000 seals, and replace if necessary. Replace the engine air cleaner filter.
Page 474 MAINTENANCE SCHEDULES 473 Perform Maintenance Every (Where time and mileage are listed, follow the interval that occurs first.) Maintenance Items Miles Kilometers or Months Change the transfer case fluid if using your vehicle for any of the following: police, taxi, fleet, off-road, or fre- 60,000 100 000 quent trailer towing.
Page 475 474 MAINTENANCE SCHEDULES WARNING! You can be badly injured working on or around a motor vehicle. Do only that service work for which you have the knowledge and the right equipment. If you have any doubt about your ability to perform a service job, take your vehicle to a competent mechanic.
Page 476 IF YOU NEED CONSUMER ASSISTANCE CONTENTS ▫ Customer Assistance For The Hearing Or Speech Suggestions For Obtaining Service For Your Vehicle 477 Impaired (TDD/TTY) ....479 ▫...
Page 477 476 IF YOU NEED CONSUMER ASSISTANCE ▫ Traction Grades ..... . 483 Department Of Transportation Uniform Tire Quality Grades ......482 ▫...
Page 478: Suggestions For Obtaining Service For Your Vehicle
IF YOU NEED CONSUMER ASSISTANCE 477 SUGGESTIONS FOR OBTAINING SERVICE FOR Be Reasonable With Requests YOUR VEHICLE If you list a number of items and you must have your vehicle by the end of the day, discuss the situation with Prepare For The Appointment the service advisor and list the items in order of priority.
Page 479: Daimlerchrysler Motors Corporation Customer Center
478 IF YOU NEED CONSUMER ASSISTANCE • Vehicle Identification Number (VIN) special tools, and the latest information to ensure your vehicle is fixed correctly and in a timely manner. • Vehicle delivery date and mileage This is why you should always talk to your authorized DaimlerChrysler Motors Corporation Customer dealer’s service manager first.
Page 480: Customer Assistance For The Hearing Or Speech Impaired (Tdd/Tty)
IF YOU NEED CONSUMER ASSISTANCE 479 contract, call the manufacturer’s Service Contract Na- Customer Assistance For The Hearing Or Speech Impaired (TDD/TTY) tional Customer Hotline at 1-800-521-9922. To assist customers who have hearing difficulties, the The manufacturer will not stand behind any service manufacturer has installed special TDD (Telecommuni- contract that is not the manufacturer’s Service Contract.
Page 481: Warranty Information (U.s. Vehicles Only)
480 IF YOU NEED CONSUMER ASSISTANCE MOPAR PARTS WARNING! MOPAR fluids, lubricants, parts, and accessories are available from your authorized dealer. They will help Engine exhaust, some of its constituents, and certain you keep your vehicle operating at its best. vehicle components contain, or emit, chemicals known to the State of California to cause cancer and REPORTING SAFETY DEFECTS...
Page 482: In Canada
IF YOU NEED CONSUMER ASSISTANCE 481 To contact NHTSA, you may either call the Auto Safety PUBLICATION ORDER FORMS Hotline toll free at 1–888–327–4236 (TTY: 1–800–424– To order the following manuals, you may use either the 9153), or go to http://www.safercar.gov; or write to: website or the phone numbers listed below.
Page 483: Department Of Transportation Uniform Tire Quality
482 IF YOU NEED CONSUMER ASSISTANCE • Diagnostic Procedure Manuals Call toll free at: • 1–800–890–4038 (U.S.) Diagnostic Procedure Manuals are filled with dia- grams, charts and detailed illustrations. These practi- • 1–800–387–1143 (Canada) cal manuals make it easy for students and technicians to find and fix problems on computer-controlled ve- hicle systems and features.
Page 484: Temperature Grades
IF YOU NEED CONSUMER ASSISTANCE 483 All passenger car tires must conform to Federal safety on specified government test surfaces of asphalt and requirements in addition to these grades. concrete. A tire marked C may have poor traction perfor- mance. Treadwear The treadwear grade is a comparative rating, based on WARNING!
Page 485 484 IF YOU NEED CONSUMER ASSISTANCE grade C corresponds to a level of performance, which all passenger car tires must meet under the Federal Motor Vehicle Safety Standard No. 109. Grades B and A repre- sent higher levels of performance on the laboratory test wheel, than the minimum required by law.
Page 486 INDEX...
Page 487 81-326-0841 First Edition Printed in U.S.A.

Jeep Liberty 2008 Owner's Manual

Introduction 1

Things to Know before Starting Your Vehicle

Understanding the Features of Your Vehicle

Instrument Panel and Controls

Starting and Operating

Quick Links

Chapters

Related Manuals for Jeep Liberty 2008

Summary of Contents for Jeep Liberty 2008