Page 1: Introduction
TABLE OF CONTENTS SECTION PAGE ............. 3 INTRODUCTION .
Page 2 I n f o r ma t i o n P r o v i d e d b y :...
Page 3: Table Of Contents
INTRODUCTION CONTENTS Introduction ......4 Warnings And Cautions ....9 ▫...
Page 4: Introduction
4 INTRODUCTION As with other vehicles of this type, failure to operate this INTRODUCTION This is a specialized utility vehicle designed for both vehicle correctly may result in loss of control or an on-road and off-road use. It can go places and perform accident.
Page 5: Roll Over Warning
INTRODUCTION 5 Roll Over Warning Utility vehicles have a significantly higher roll over rate than other types of vehicles. This vehicle has a higher ground clearance, higher center of gravity, and narrower track than many passenger cars. It is capable of perform- ing better in a wide variety of off-road applications.
Page 6 6 INTRODUCTION Failure to use driver and passenger seat belts provided Operating this vehicle at excessive speeds or while is a major cause of severe or fatal injury. In fact, the U.S. intoxicated may result in loss of control, collision with government notes that the universal use of existing seat other vehicles or objects, going off the road, or overturn- belts could cut the highway death toll by 10,000 or more...
Page 7: How To Use This Manual
INTRODUCTION 7 NOTE: After you read the manual, it should be stored HOW TO USE THIS MANUAL in the vehicle for convenient reference and remain with Consult the table of contents to determine which section the vehicle when sold so that the new owner will be contains the information you desire.
Page 8 8 INTRODUCTION I n f o r ma t i o n P r o v i d e d b y :...
Page 9: Warnings And Cautions
INTRODUCTION 9 WARNINGS AND CAUTIONS VEHICLE MODIFICATIONS/ALTERATIONS This manual contains WARNINGS against operating WARNING! procedures, which could result in an accident or bodily injury. It also contains CAUTIONS against procedures, Any modifications or alterations to this vehicle could which could result in damage to your vehicle. If you do seriously affect its roadworthiness and safety and not read this entire manual, you may miss important may lead to an accident resulting in serious injury or...
Page 10 I n f o r ma t i o n P r o v i d e d b y :...
Page 11 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE CONTENTS ▫ Customer Key Programming ....18 A Word About Your Keys ....14 ▫...
Page 12 12 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE ▫ Using The Panic Alarm ....22 ▫ Wind Buffeting ......34 ▫...
Page 13 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 13 ▫ Child Restraint ......64 ▫ Safety Checks You Should Make Inside The Vehicle .
Page 14: A Word About Your Keys
14 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE A WORD ABOUT YOUR KEYS The keys for your new vehicle are enclosed in a plastic bag with the key code number on it. If you received your keys without the bag, ask your dealer to give you the number.
Page 15: Key-In-Ignition Reminder
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 15 Key-In-Ignition Reminder WARNING! Opening the driver’s door when the key is in the ignition, sounds a signal to remind you to remove the key. Leaving children in a vehicle unattended is danger- ous for a number of reasons.
Page 16: To Release The Steering Wheel Lock
16 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE The Sentry Key Immobilizer System does not need to be To Release the Steering Wheel Lock Insert the key in the ignition and turn the wheel slightly armed or activated. Operation of the system is automatic to the right or left to disengage the lock.
Page 17: Important Note About Service
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 17 longer than 10 seconds) a fault has been detected in the Important Note About Service electronics and the vehicle should be serviced as soon as A four digit PIN number is needed to service the Sentry possible.
Page 18: Customer Key Programming
18 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE consists of programming a blank key to the vehicle will sound and the “Security Alarm System Indicator electronics. A blank key is one which has never been Light” will begin to flash. Turn the ignition switch OFF programmed.
Page 19: Security Alarm System - If Equipped
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 19 2. This device must accept any interference that may be To Set the Alarm received, including interference that may cause undes- The alarm will set when you use the remote keyless entry ired operation.
Page 20: Illuminated Entry
20 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE The Security Alarm System is designed to protect your REMOTE KEYLESS ENTRY — IF EQUIPPED vehicle; however, you can create conditions where the system will arm unexpectedly. If you remain in the vehicle and lock the doors with the transmitter, once the system is armed (after 16 seconds), when you pull the door handle to exit the alarm will sound.
Page 21: To Unlock The Doors And Swing Gate
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 21 NOTE: The line of transmission must not be blocked 4. Test the feature while outside of the vehicle, by with metal objects. pressing the “Lock/Unlock” button on the keyfob. To Unlock the Doors and Swing Gate NOTE: Pressing the “Lock”...
Page 22: Using The Panic Alarm
22 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 2. While the “Lock” button is pressed (after 4 seconds), To Turn Off “Flash Lights With Lock” press the PANIC button. Release both buttons. NOTE: The Flash Lights With Lock feature can be The “Sound Horn On Lock”...
Page 23: Programming Additional Transmitters
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 23 The “Flash Lights On Lock/Unlock” feature can be 3. Place the key into the ignition. reactivated by repeating this procedure. 4. Turn the ignition to the ON position ( Do not start the Programming Additional Transmitters engine ).
Page 24: General Information
24 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 11. A single chime will be heard. 2. This device must accept any interference that may be received including interference that may cause undesired 12. Repeat steps 8 through 10 to program up to six operation.
Page 25: Battery Replacement
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 25 Battery Replacement The recommended replacement battery is CR2032. NOTE: Perchlorate Material – special handling may apply, See www.dtsc.ca.gov/hazardouswaste/perchlorate 1. If the key fob is equipped with a screw, remove the screw. With the transmitter buttons facing down, use a flat blade (screw driver) to pry the two halves of the transmitter apart.
Page 26: Doors
26 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 3. To assemble the transmitter case, snap the two halves If the trip/reset button is pressed while the VF warnings together. are being displayed, the VF display will revert back to only displaying the odometer/trip odometer mileage. NOTE: If the key fob is equipped with a screw, reinstall and tighten the screw until snug.
Page 27: Rear Door Removal (4 Door Models)
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 27 2. Unplug wiring harness connector under instrument To reinstall the door(s), perform the above steps in the panel. opposite order. Rear Door Removal (4 Door Models) 1. Remove the hinge pin screws from the upper and lower outside hinges (using a #T50 Torx head driver).
Page 28 28 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 3. Remove interior B-pillar trim access door at bottom of B-pillar. 5. Unhook door strap from the body hook. 6. With the door open, lift the door to clear hinge pins 4. Unplug wiring harness connector. from their hinges, and remove door.
Page 29: Door Locks
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 29 (One chime for each complete display cycle (three cycles DOOR LOCKS The vacuum fluorescent (VF) display located in the total). After this, the display will continue to cycle only odometer area displays the word “door” as an indication (no chimes).
Page 30: Manual Door Locks
30 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Manual Door Locks WARNING! The front (2 Door Models) and rear doors (4 Door Models) are equipped with a rocker-type interior door • For personal security reasons and safety in an lock. To lock a door when leaving your vehicle, press to accident, lock the vehicle doors when you drive as the “Lock”...
Page 31: Power Door Locks - If Equipped
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 31 Power Door Locks — If Equipped WARNING! The door lock switch is located on each front door panel. Press the switch downward to lock the doors, and • For personal security reasons and safety in an upward to unlock the doors.
Page 32: Windows
32 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WINDOWS Power Windows — If Equipped The power window switches are located on the instru- ment panel center stack (below the radio). The top left switch controls the left front window and the top right switch controls the right front window.
Page 33 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 33 Auto Down Both the driver and front passenger window switch has an “Auto Down” feature. Press the window switch past the first detent, release, and the window will go down automatically. To cancel the “Auto Down” movement, operate the switch in either the up or down direction and release the switch.
Page 34: Wind Buffeting
34 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Window Lockout Switch (4 Door Models Only) REAR SWING GATE The window lockout switch (located between the win- The vacuum fluorescent (VF) display located in the dow switches) allows you to disable the rear window odometer area displays the word “gATE”...
Page 35 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 35 The swing gate can be unlocked using the remote keyless NOTE: Close flip-up window before swing gate (hard entry, or by activating the power door lock switches top models only). located on the front doors. CAUTION! To open the swing gate, press the button on the gate handle.
Page 36: Occupant Restraints
36 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE OCCUPANT RESTRAINTS WARNING! Some of the most important safety features in your vehicle are the restraint systems. These include the front In a collision, you and your passengers can suffer and rear seat belts for the driver and all passengers, front injuries, including fatalities, if you are not properly airbags for both the driver and front passenger, and side buckled up.
Page 37: Lap/Shoulder Belts
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 37 Research has shown that seat belts save lives, and that WARNING! they can reduce the seriousness of injuries in a collision. Some of the worst injuries happen when people are • It is extremely dangerous to ride in a cargo area, thrown from the vehicle.
Page 38 38 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Lap/Shoulder Belt Operating Instructions WARNING! 1. Enter the vehicle and close the door. Sit back and • Wearing a seat belt incorrectly is dangerous. Seat adjust the seat. belts are designed to go around the large bones of 2.
Page 39 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 39 Latch Plate Latch Plate To Buckle 3. When the belt is long enough to fit, insert the latch plate into the buckle until you hear a “click.” I n f o r ma t i o n P r o v i d e d b y :...
Page 40 40 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 4. Position the lap belt across your thighs, below your WARNING! abdomen. To remove slack in the lap belt portion, pull up on the shoulder belt. To loosen the lap belt if it is too tight, A belt that is buckled into the wrong buckle will not tilt the latch plate and pull on the lap belt.
Page 41 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 41 NOTE: The “Seat Belt Indicator Light” will remain on WARNING! until the driver’s seat belt is buckled. A lap belt worn too high can increase the risk of internal injury in a collision. The belt forces won’t be at the strong hip and pelvic bones, but across your abdomen.
Page 42: Rear Center Lap/Shoulder Belt Retractor Lock-Out
42 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 6. To release the belt, push the red button on the buckle. Rear Center Lap/Shoulder Belt Retractor The belt will automatically retract to its stowed position. Lock-Out If necessary, slide the latch plate down the webbing to This feature is designed to lock the retractor whenever allow the belt to retract fully.
Page 43: Adjustable Upper Shoulder Belt Anchorage
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 43 WARNING! The rear center lap/shoulder belt is equipped with a lock-out feature to ensure that the rear seat back is in the fully upright and locked position when occupied. If the rear seat back is not fully upright and locked and the rear center lap/shoulder belt can be pulled out of the retractor, the vehicle should immediately be taken to your dealer for service.
Page 44: Seat Belt Pretensioners
44 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Seat Belt Pretensioners WARNING! The driver and front passenger seat belts are equipped with a pretensioning device that is designed to remove Position the shoulder belt height adjusters so that the any slack from the seat belt systems in the event of a belt rests across the middle of your shoulder.
Page 45: Enhanced Seat Belt Use Reminder System (Beltalert)
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 45 The Enhanced Warning System (BeltAlert) can be en- Enhanced Seat Belt Use Reminder System (BeltAlert) abled or disabled by your authorized dealer or by If the driver or front passenger seat belt has not been following these steps: buckled within 60 seconds of starting the vehicle and if NOTE: The following steps must occur within the first...
Page 46: Seat Belts And Pregnant Women
46 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 4. Turn the ignition key to the OFF position. A single Pregnant women should wear the lap part of the belt chime will sound to signify that you have successfully across the thighs and as snug across the hips as possible. completed the programming.
Page 47: Driver And Front Passenger Supplemental Restraint Systems (Srs)
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 47 Driver And Front Passenger Supplemental WARNING! Restraint Systems (SRS) Using a seat belt extender when not needed can increase the risk of injury in a collision. Only use when the seat belt is not long enough when it is worn low and snug, and in the recommended seating positions.
Page 48 48 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE This vehicle has airbags for both the driver and right front passenger as a supplement to the seat belt restraint systems. The driver’s front airbag is mounted in the steering wheel. The passenger side airbag is mounted in the instrument panel, above the glove compartment.
Page 49 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 49 The front airbags have a multi stage inflator design. This WARNING! allows the airbag to have different rates of inflation that are based on collision severity. Along with the seat belts, • Do not put anything on or around the front airbag covers front airbags work with the instrument panel knee bol- or attempt to manually open them.
Page 50 50 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE severe side collisions. In certain types of collisions, both child restraint or belt-positioning booster seat. Older the front and side airbags may be triggered. But even in children who do not use child restraints or belt- collisions where the airbags work, you need the seat belts positioning booster seats should ride properly buckled to keep you in the right position for the airbags to protect...
Page 51 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 51 3. The driver and front passenger seats should be moved WARNING! back as far as practical to allow the front airbags room to inflate. • Relying on the airbags alone could lead to more severe injuries in a collision.
Page 52 52 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • Occupant Classification System (OCS) — Front Pas- Airbag System Components The airbag system consists of the following: senger Seat Only • Occupant Restraint Control Module − Occupant Classification Module • Airbag Warning Light −...
Page 53 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 53 The ORC also monitors the readiness of the electronic either momentarily or continuously. A single chime parts of the system whenever the ignition switch is in will sound if the light comes on again after initial start the START or ON positions.
Page 54 54 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • The Occupant Classification System (OCS) is part of a Federally regulated safety system required for this vehicle. It is designed to turn off the front passenger airbag in the unlikely event that a rear-facing infant seat is in the front passenger seat.
Page 55 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 55 The “PAD Indicator Light” should not be illuminated NOTE: Even though this vehicle is equipped with an when teenagers, most children in a forward-facing Occupant Classification System, children 12 years and child restraint or booster seats, most children that can under should always ride buckled up in a rear seat in an properly wear the vehicle’s seat belt, and when an appropriate child restraint.
Page 56 56 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE The OCS classifies an occupant using weight sensors measured properly and may result in the occupant being mounted in the base of the front passenger seat. Any improperly classified. Ensure that the front passenger weight on the seat will be sensed by the system.
Page 57 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 57 both the “PAD Indicator Light” and the “Airbag Warning about half of the time it takes to blink your eyes. The Light” are illuminated to show that the passenger airbag bags then quickly deflate while helping to restrain the is turned off until the fault is cleared.
Page 58 58 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • Your vehicle has four Weight Sensors located between airbag exits through the seat seam into the space between the seat and the floor pan. The weight sensors measure the occupant and the door. The side airbag moves at a applied weight and transfers that information to the very high speed and with such a high force, that it could OCM.
Page 59 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 59 • At no time should any supplemental restraint system The following requirements must be strictly adhered to: (SRS) component or SRS related component or fas- • Do not modify the front passenger seat assembly or tener be modified or replaced with any part except components in any way.
Page 60 60 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE If A Deployment Occurs They are not permanent and normally heal quickly. The airbag system is designed to deploy when the However, if you haven’t healed significantly within a Occupant Restraint Control (ORC) Module detects a few days, or if you have any blistering, see your doctor moderate-to-severe frontal collision, to help restrain the immediately.
Page 61 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 61 Maintaining Your Airbag System WARNING! WARNING! Deployed airbags and seat belt pretensioners cannot protect you in another collision. Have the airbags, • Modifications to any part of the airbag system could cause it to fail when you seat belt pretensioner, and seat belt retractor assem- need it.
Page 62 62 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: Perchlorate Material – special handling may apply, and up to a quarter second of high-speed deceleration See www.dtsc.ca.gov/hazardouswaste/perchlorate data during and/or after air bag deployment or near- deployment. EDR data are ONLY recorded if an airbag Airbag Warning Light deploys, or nearly deploys, and are otherwise unavail- You will want to have the airbag system ready to inflate...
Page 63 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 63 DaimlerChrysler Corporation, such investigations may nature, such as would identify a particular driver, ve- be requested by customers, insurance carriers, govern- hicle, or crash, will be treated confidentially. Confidential ment officials, and professional crash researchers, such as data will not be disclosed by DaimlerChrysler Corpora- those associated with universities, and with hospital and tion to any third party except when:...
Page 64: Child Restraint
64 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • Airbag disable lamp status (if equipped) Child Restraint Everyone in your vehicle needs to be buckled up at all • Time of airbag deployment (in terms of ignition times — babies and children, too. Every state in the cycles and vehicle mileage) United States and all Canadian provinces require that •...
Page 65 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 65 • The infant carrier is only used rearward-facing in the WARNING! vehicle. It is recommended for children who weigh up to about 20 lbs (9 kg). “Convertible” child seats often In a collision, an unrestrained child, even a tiny baby, have a higher weight limit in the rearward-facing can become a missile inside the vehicle.
Page 66 66 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Standards. The manufacturer also recommends that WARNING! you try a child restraint in the vehicle seats where you will use it before you buy it. • Improper installation can lead to failure of an infant or child restraint.
Page 67 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 67 • Buckle the child into the restraint exactly as the extracted from the retractor. Allow the belt to return to the retractor, pulling on the excess webbing to tighten manufacturer’s instructions tell you. the lap portion about the child restraint.
Page 68 68 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • The lap portion should be low on the hips and as snug vehicle by the lap/shoulder belt or the LATCH child restraint anchorage system (Refer to LATCH — Child as possible. Seat Anchorage System in this section.) •...
Page 69 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 69 NOTE: To reset this feature you must let all of the belt head restraint and attached to the tether anchor on the webbing return into the retractor. You will not be able to rear of the seat back.
Page 70 70 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE LATCH — Child Seat Anchorage System (Lower kits or retro-fit kits. You are urged to take advantage of all Anchors and Tether for CH ildren) the available attachments provided with your child re- Your vehicle’s rear seat is equipped with the child straint in any vehicle.
Page 71 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 71 The rear seating positions have lower anchorages that are center position. If your child restraints are not LATCH- capable of accommodating LATCH-compatible child compatible, you can only install the child restraints using seats having flexible, webbing-mounted lower attach- the vehicle’s seat belts.
Page 72 72 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE The rear seat lower anchorages are round bars, located at the rear of the seat cushion where it meets the seat back, and are visible when you lean into the rear seat to install the child restraint.
Page 73 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 73 Latch Anchorages (4 Door Models) Tether Strap Mounting (2 Door Models) In addition, there are tether strap anchorages behind each rear seating position located on the back of the seat. I n f o r ma t i o n P r o v i d e d b y :...
Page 74 74 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE hook for attachment to the tether strap anchorage and a means of adjusting the tension of the strap. You will first loosen the adjusters on the lower straps and on the tether strap so that you can more easily attach the hooks or connectors to the vehicle anchorages.
Page 75 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 75 If the seat belt has a automatic locking retractor, it will WARNING! have a distinctive label. Pull the belt from the retractor until there is enough to allow you to pass through the Improper installation of a child restraint to the child restraint and slide the latch plate into the buckle.
Page 76 76 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE to do something more. Disconnect the latch plate from the buckle, turn the buckle around, and insert the latch plate into the buckle again. If you still can’t make the child restraint secure, try a different seating position. To attach a child restraint tether strap: Tether Strap Mounting (4 Door Models) Route the tether strap over the seat back and attach the...
Page 77: Engine Break-In Recommendations
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 77 ENGINE BREAK-IN RECOMMENDATIONS WARNING! A long break-in period is not required for the engine in your new vehicle. An incorrectly anchored tether strap could lead to increased head motion and possible injury to the Drive moderately during the first 300 miles (500 km).
Page 78: Safety Tips
78 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • Do not inhale exhaust gases. They contain carbon A new engine may consume some oil during its first few thousand miles (kilometers) of operation. This should be monoxide, a colorless and odorless gas which can kill. considered as a normal part of the break-in and not Never run the engine in a closed area, such as a interpreted as an indication of difficulty.
Page 79: Safety Checks You Should Make Inside The Vehicle
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 79 • On hardtop models, keep the tailgate window closed Airbag Warning Light when driving your vehicle. On fabric top models, do The light should come on and remain on for 6 to 8 not drive with the rear window curtain up unless the seconds as a indicator check when the ignition switch is side curtains are also open.
Page 80: Safety Checks You Should Make Outside The Vehicle
80 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Fluid Leaks Safety Checks You Should Make Outside The Vehicle Check area under vehicle after overnight parking for fuel, coolant, oil, or other fluid leaks. Also, if gasoline fumes Tires are detected, the cause should be located and corrected Examine tires for excessive tread wear or uneven wear immediately.
Page 81: Understanding The Features Of Your Vehicle
UNDERSTANDING THE FEATURES OF YOUR VEHICLE CONTENTS ▫ Head Restraints ..... . .90 Mirrors .......85 ▫...
Page 82 82 UNDERSTANDING THE FEATURES OF YOUR VEHICLE ▫ Windshield Wiper Operation ... . . 102 Lights ....... .97 ▫...
Page 83 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 83 Electronic Brake Control System ... . 107 Dual Top — If Equipped ....120 ▫...
Page 84 84 UNDERSTANDING THE FEATURES OF YOUR VEHICLE ▫ Door Frame Removal (4 Door Models) ..135 Folding Windshield ..... 187 ▫...
Page 85: Mirrors
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 85 Annoying headlight glare can be reduced by moving the MIRRORS small control under the mirror to the night position Inside Day/Night Mirror (toward rear of vehicle). The mirror should be adjusted The mirror should be adjusted to center on the view while set in the day position (toward windshield).
Page 86: Outside Mirrors
86 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Outside Mirrors WARNING! To receive maximum benefit, adjust the outside mirror(s) to center on the adjacent lane of traffic with a slight • Vehicles and other objects seen in the right side overlap of the view obtained on the inside mirror. convex mirror will look smaller and farther away than they really are.
Page 87: Seats
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 87 SEATS Front Seat Adjustment Move seat forward or rearward by lifting the lever. Be WARNING! sure the latch engages fully. Adjusting a seat while the vehicle is moving is dangerous. The sudden movement of the seat could cause you to lose control.
Page 88: Manual Seat Height Adjustment - If Equipped
88 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Manual Seat Height Adjustment — If Equipped Front Seat Back Recline The driver’s seat height can be raised or lowered, by To recline: using the ratcheting handle on the outboard side of the 1.
Page 89: Front Passenger Easy Entry Seat (2 Door Models)
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 89 2. Lift the handle to return the seatback to an upright position. Front Passenger Easy Entry Seat (2 Door Models) Push the lever on the seatback rearward (toward the rear of the vehicle) to tilt the entire seat forward. Easy Entry Lever I n f o r ma t i o n P r o v i d e d b y :...
Page 90: Head Restraints
90 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Head Restraints Head restraints can reduce the risk of whiplash injury in the event of impact from the rear. Adjustable head restraints should be adjusted so that the upper edge is as high as practical. The front head restraints have a locking button that must be pushed inward to lower the head restraint.
Page 91 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 91 Also, be sure that the front seats are fully upright and positioned forward. This will allow the rear seat to fold down easily. 1. Lift the seatback release lever and fold seatback for- ward.
Page 92: Removing The Rear Seat (2 Door Models)
92 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 1. Remove the rear subwoofer (if equipped) mounting Removing the Rear Seat (2 Door Models) screws (3) using a #T30 Torx head driver. WARNING! • It is extremely dangerous to ride in a cargo area, inside or outside of a vehicle.
Page 93: Replacing The Rear Seat (2 Door Models)
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 93 4. Press down on release bar on each side, and pull seat Replacing the Rear Seat (2 Door Models) out and away from lower bracket. Reverse steps for removing the seat. 5. Remove seat from the vehicle. WARNING! •...
Page 94 94 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: Prior to folding the rear seat, it may be necessary To Fold Down the Rear Seat to reposition the front seat to it’s mid-track position. 1. Locate the seatback release handle on the outboard top Also, be sure that the front seats are fully upright and side of each rear seatback;...
Page 95: To Raise The Rear Seat
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 95 NOTE: When lifting up on the release handle, the To Raise the Rear Seat seatback will release easier if you do not pull forward on 1. Raise the seatback and lock it into place. If interference the seatback;...
Page 96: To Open And Close The Hood
96 UNDERSTANDING THE FEATURES OF YOUR VEHICLE have to push down slightly on hood before pushing the TO OPEN AND CLOSE THE HOOD To open hood, first release both hood latches. handle. Insert the support rod into the slot on the hood panel.
Page 97: Lights
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 97 Also, the rear cargo lamp may be operated by pressing LIGHTS the lens to turn it on. Press the lens again, to shut it off. Interior Lights The overhead light comes on when a door is opened. It may also be turned on by rotating the control for the dimmer switch on the multi-function control lever fully upward.
Page 98: Multi-Function Control Lever
98 UNDERSTANDING THE FEATURES OF YOUR VEHICLE When a door is open and the interior lights are on, Daytime Brightness Feature rotating the dimmer control all the way down to the OFF Certain instrument panel components (odometer, radio detent will cause all the interior lights to go out. This is display) can be illuminated at full brightness during the also known as the Party mode because it allows the daytime.
Page 99: Parking Lights, Instrument Panel Lights, And Headlights
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 99 Multi-Function Control Lever Headlight Switch Parking Lights, Instrument Panel Lights, and To change the brightness of the instrument panel lights, Headlights rotate the center portion of the multi-function control Turn the end of the multi-function control lever to the lever up or down.
Page 100: Lights-On Reminder
100 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: If the driver’s door is left open, and the head- Front Fog Lights — If Equipped lights or parking lights are left on, the “High Beam The front fog light switch is in the multi-function Indicator Light”...
Page 101: Daytime Running Lights - If Equipped
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 101 If either light remains on and does not flash, or there is a WINDSHIELD WIPERS AND WASHERS very fast flash rate, check for a defective outside light CAUTION! bulb. If an indicator fails to light when the lever is moved, it would suggest that the indicator bulb is In cold weather, always turn off the wiper switch and defective.
Page 102: Windshield Wiper Operation
102 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Windshield Wiper Operation Windshield Washers Move the lever upward to the second detent for LO speed To use the washer, pull the lever toward you and hold wiper operation, or to the third detent for HI speed while spray is desired.
Page 103: Tilt Steering Column
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 103 TILT STEERING COLUMN WARNING! To tilt the column, push down on the lever under the multi-function control lever and move the wheel up or Tilting the steering column while the vehicle is down, as desired. Pull the lever back upwards to lock the moving is dangerous.
Page 104: Electronic Speed Control - If Equipped
104 UNDERSTANDING THE FEATURES OF YOUR VEHICLE ELECTRONIC SPEED CONTROL — IF EQUIPPED To Activate When engaged, this device takes over the accelerator Push the ON/OFF button. The CRUISE indicator in the operation at speeds greater than 35 mph (56 km/h). The instrument cluster will illuminate.
Page 105: To Set At A Desired Speed
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 105 To Set At A Desired Speed To Resume Speed When the vehicle has reached the desired speed, press To resume a previously set speed, push the “RESUME down on the lever and release. Release the accelerator ACCEL”...
Page 106: Manual Transmission
106 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To decrease speed while speed control is ON, push down WARNING! and hold “SET DECEL”. Release the lever when the desired speed is reached, and the new speed will be set. Speed Control can be dangerous where the system can’t maintain a constant speed.
Page 107: Electronic Brake Control System
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 107 On steep hills, a greater speed loss or gain and/or more help avoid skidding on slippery surfaces during braking. frequent downshifts (auto transmission only) may occur Refer to “Anti-Lock Brake System” in Section 5 of this so it may be preferable to drive without speed control.
Page 108: Tcs (Traction Control System)
108 UNDERSTANDING THE FEATURES OF YOUR VEHICLE TCS (Traction Control System) BAS (Brake Assist System) The BAS is designed to optimize the vehicle’s braking This system monitors the amount of wheel spin of each of capability during emergency braking maneuvers. The the driven wheels.
Page 109: Erm (Electronic Roll Mitigation)
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 109 ERM (Electronic Roll Mitigation) WARNING! This system anticipates the potential for wheel lift by monitoring the driver’s steering wheel input and the BAS (Brake Assist System) cannot prevent the natu- speed of the vehicle. When ERM determines that the rate ral laws of physics from acting on the vehicle, nor can of change of the steering wheel angle and vehicles speed it increase the traction afforded by prevailing road...
Page 110: Esp (Electronic Stability Program)
110 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: Anytime the ESP system is in the “Full Off” ESP (Electronic Stability Program) mode, ERM is disabled. Refer to ESP (Electronic Stability This system enhances directional control and stability of Program) for a complete explanation of the available ESP the vehicle under various driving conditions.
Page 111 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 111 • Understeer - when the vehicle is turning less than WARNING! appropriate for the steering wheel position. ESP (Electronic Stability Program) cannot prevent the The ESP/TCS Indicator Light located in the instrument natural laws of physics from acting on the vehicle, cluster, starts to flash as soon as the tires lose traction and nor can it increase the traction afforded by prevailing the ESP system becomes active.
Page 112 112 UNDERSTANDING THE FEATURES OF YOUR VEHICLE High Range (4WD Models) or 2WD Models conditions and more wheel spin than ESP would nor- mally allow is required to gain traction. To turn ESP on again, momentarily depress the ESP Control Switch . This is the normal operating mode for ESP in 4WD high This will restore the normal “ESP On”...
Page 113 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 113 NOTE: To improve the vehicle’s traction when driving sound, the ESP/TCS Indicator Light will illuminate, with snow chains, or starting off in deep snow, sand, or and the ESP OFF message will appear in the odometer. gravel, it may be desirable to switch to the “Partial Off”...
Page 114 114 UNDERSTANDING THE FEATURES OF YOUR VEHICLE except for the “limited slip” feature described in the TCS WARNING! section, are turned off until the vehicle reaches a speed of 40 mph (48 km/h). At 40 mph (48 km/h), the normal ESP With the ESP switched off, the enhanced vehicle stability function returns but TCS remains off.
Page 115: Esp/Bas Warning Lamp
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 115 If the “ESP/BAS Warning Lamp” comes on continuously WARNING! with the engine running, a malfunction has been detected in either the ESP or the BAS system, or both. If this light With the ESP switched off, the enhanced vehicle remains on after several ignition cycles, and the vehicle stability offered by ESP and ERM are unavailable.
Page 116: Electrical Power Outlet
116 UNDERSTANDING THE FEATURES OF YOUR VEHICLE ELECTRICAL POWER OUTLET This vehicle has two auxiliary power outlets that can provide up to 20 Amps of current for accessories de- signed for use with the standard power outlet adapters. The outlet located in the lower portion of the instrument panel has a snap on plastic cap so that it can be covered when not in use.
Page 117: Electrical Outlet Use With Engine Off
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 117 Electrical Outlet Use With Engine Off CUP HOLDERS In the center console there are two cup holders for the WARNING! front seat passengers. NOTE: The cup holder insert is removable from the • Many accessories that can be plugged in draw power console, for cleaning.
Page 118: Storage
118 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The rear passengers have cup holders at the rear of the STORAGE center console. Console Storage Compartment To lock or unlock, insert ignition key and turn. To open, press the latch and lift cover. Rear Cup Holders Center Console I n f o r ma t i o n P r o v i d e d b y :...
Page 119: Rear Storage Compartment
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 119 Rear Storage Compartment The rear storage compartment cover is held by a spring loaded latch. In order to remove the rear storage com- partment cover, use the following procedure: NOTE: The rear storage compartment latch should not be used as cargo tie-down.
Page 120: Dual Top - If Equipped
120 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • Door frame attachment knobs (4 for 2 door models, DUAL TOP — IF EQUIPPED If your vehicle is equipped with a Dual Top, you must 6 for 4 door models) remove one of the tops from the vehicle. If the soft top •...
Page 121 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 121 3. Remove the soft top bow assembly pivot bracket 4. Using a rubber mallet, carefully tap the knuckles from screws (2 per side) using a #T30 Torx head driver. the left and right metal pivot brackets. Remove the soft top from the vehicle and store in a clean, dry location.
Page 122: Installing The Soft Top
122 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 5. Unzip the zipper on the sport bar cover to expose the Installing the Soft Top pivot brackets. Remove the brackets using a #T30 Torx NOTE: The following procedures are for first time set head driver.
Page 123 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 123 3. Install the door frames. Refer to “Door Frame” in this section. 4. If the soft top has been removed, follow these steps to reinstall the soft top. If the soft top is on the vehicle, proceed to step #5.
Page 124 124 UNDERSTANDING THE FEATURES OF YOUR VEHICLE c. Tap the knuckles on the side with a rubber mallet to reattach them to the metal pivot brackets. CAUTION! d. Screw the pivot screws back into place using a #T30 Do not overtighten the screws. You can strip the Torx head driver.
Page 125: Freedom Top 3- Piece Modular Hard Top
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 125 5. Unsnap and remove the black boot cover. This cover FREEDOM TOP 3– PIECE MODULAR HARD TOP should be discarded. It was intended as a protective CAUTION! cover for shipping only. NOTE: A visual instruction sheet is enclosed in the dual •...
Page 126: Front Panel(S) Removal
126 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 3. Turn rear l-shaped lock (located above shoulder belt Front Panel(s) Removal anchorage). NOTE: Left panel must be removed before removing right panel. 1. Fold down the sun visor, and move to the side. 2.
Page 127 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 127 4. Turn rear fasteners (knobs) (located on overhead speaker bar assembly) counter-clockwise until they can be removed. 6. Remove panel. To remove right panel, follow steps above except for step 5. Unlatch the header panel latch located at the top of the windshield.
Page 128: Front Panel(S) Installation
128 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Front Panel(s) Installation NOTE: The front panel (s) must be positioned properly to ensure sealing. Set the panels on the windshield frame so that there is no overhang. Also, make sure that the panels are sitting flush with the body.
Page 129: Rear Panel Removal
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 129 2. Install right panel first, then the left panel. 5. Open swing gate all the way to ensure clearance of the rear window glass. Lift rear window glass. 3. Reinstall panel(s) using the same steps for removal in reverse order.
Page 130 130 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 6. Locate the wiring harness at the rear left side corner of CAUTION! the vehicle. Make sure storage cap is installed to prevent foreign materials from entering tube and clogging system, and also prevent fluid from being sprayed into rear of vehicle.
Page 131: Rear Panel Installation
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 131 Rear Panel Installation NOTE: If the door frames are installed from soft top usage, they must be removed prior to installation of the hard top. 1. Inspect the hard top seals for damage and replace if necessary.
Page 132: Door Frame
132 UNDERSTANDING THE FEATURES OF YOUR VEHICLE DOOR FRAME WARNING! Do not drive your vehicle on-pavement with the door frame removed as you lose the protection these structural elements can provide. This procedure is furnished for use during off-road operation only. Door Frame Removal (2 Door Models) 1.
Page 133 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 133 2. Place one hand on the upper rear and one hand on the front of the door frame. 3. Pull the frame towards you with your rearward hand to remove the frame from the vehicle. WARNING! Never store the door frames in your vehicle.
Page 134: Door Frame Installation (2 Door Models)
134 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 3. After the door frame pin has been set into the bodys- Door Frame Installation (2 Door Models) ide hole, carefully set the front of the door frame into the 1. Unfold door frame and unscrew thumbscrews. rubber seal at the top of the windshield.
Page 135: Door Frame Removal (4 Door Models)
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 135 5. Starting with the front knob, screw in and tighten both Door Frame Removal (4 Door Models) knobs. Repeat on the other side. 1. Unscrew and remove the two (2) forward most door frame attachment knobs.
Page 136 136 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! Use both hands to remove the door frames. The door frames will fold and could cause injury if both hands are not used. 2. Place one hand on the upper rear and one hand on the upper front of the front door frame.
Page 137 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 137 3. Pull the frame towards you with your front hand to 5. Place one hand on the upper rear and one hand on the remove the frame from the vehicle. upper front of the rear door frame. Pull the frame towards you with your rear hand to remove the frame 4.
Page 138: Door Frame Installation (4 Door Models)
138 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 6. Screw the knob back into the door frame and fold for WARNING! storage. Store in a secure location. • Never store the door frames in your vehicle. In an event of an accident, a loose door frame many cause personal injury.
Page 139 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 139 3. Position the top of the door frame against the metal 4. Loosely install the rear knob (long knob) to hold the sport bar and press onto the side bar making sure not to door rail in position.
Page 140 140 UNDERSTANDING THE FEATURES OF YOUR VEHICLE door frame. Position the rear of the front door frame to 7. Tighten the front knob, then the rear most knob, and lay on top of the front of the rear door frame. then the middle knob.
Page 141: Soft Top (2 Door Models)
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 141 If the temperature is below 72°F (24°C) and/or the top SOFT TOP (2 DOOR MODELS) has been folded down for a period of time, the top will CAUTION! appear to have shrunk when you raise it, making it difficult to put up.
Page 142 142 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CAUTION! WARNING! • Do not drive vehicle with rear window curtain up • Do not run a fabric top through an automatic car wash. Window scratches and wax build up may result. unless side curtains are also removed. Dangerous •...
Page 143: Folding Down The Soft Top
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 143 Folding Down The Soft Top 1 — Header Bow 6 — Body Side Retainer 2 — 2 Bow 7 — Quarter Window 3 — 3 Bow 8 — Check Strap 4 — Sail Panel 9 —...
Page 144 144 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 1 — Zipper Start 2 — Zipper Finish 3 — Swing Gate Bar 4 — Swing Gate Brackets 5 — Sail Panels I n f o r ma t i o n P r o v i d e d b y :...
Page 145 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 145 NOTE: Clean side and rear windows before removal to assist in preventing scratching during removal of the soft top. If zippers are difficult to operate due to road dust, etc., clean them with a mild soap solution and a small brush.
Page 146 146 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 3. Unclip and move the sun visors to the side. 6. Before unzipping the rear window, release the first three (3) inches of both sail panels from the channel. 4. Release the header latches and leave the hooks in the Remove the swing gate bar by pulling it straight rear- loops on the windshield.
Page 147 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 147 • Unzip the rear window starting at the right lower 7. Undo the Velcro that runs along the top and rear corner of the window. Pull the zipper up, across the edge of the side window. top and down to the left lower corner.
Page 148 148 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 9. Once unzipped, remove side window retainers from NOTE: When releasing the sail panel retainers, it is the door channel and body side channel. Repeat this step helpful to pull down on the rear roof bow. on the opposite side.
Page 149 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 149 12. The swing gate brackets do not need to be removed 13. Completely release the latches from the loops on the unless the hard top is being installed. To remove the windshield frame. swing gate brackets, pull the front of the bracket forward while rolling the entire bracket back in towards the vehicle to disengage.
Page 150 150 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 14. Grasp the side bow behind the header, lift the top, When the top is completely down, position the drip rails and fold toward the rear of the vehicle. so they make a “v-shape”, this prevents damage to the soft top material.
Page 151: Putting Up The Soft Top
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 151 Putting Up The Soft Top 1 — Header Bow 6 — Body Side Retainer 2 — 2 Bow 7 — Quarter Window 3 — 3 Bow 8 — Check Strap 4 — Sail Panel 9 —...
Page 152 152 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 1 — Zipper Start 2 — Zipper Finish 3 — Swing Gate Bar 4 — Swing Gate Brackets 5 — Sail Panels I n f o r ma t i o n P r o v i d e d b y :...
Page 153 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 153 1. Unclip and move the sun visors to the side. 2. Install door frames, if removed. Refer to “Door Frame” in this section. 3. Standing on the side of the vehicle, lift the top by the side bow and the 2–bow (middle bow) up and over the sports bar until the header rests on the top of the windshield frame.
Page 154 154 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 5. Open the header latches and engage the hook on each side of the body channel. Then, rotate it rearward and side onto the windshield loops (do not close the latches). over the channel until it snaps onto the exterior part of the rail.
Page 155 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 155 7. Move to the rear of the vehicle and gently pull the sail rear window loose (on both sides). Pulling down on the panels over the rear roof bow. rear roof bow (3 bow) will aid to reach the channel with the retainers.
Page 156 156 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 9. To install the side windows, affix the window tempo- properly positioned on the door frame. Failure to do so rarily by attaching to the Velcro in the rear corner. Start can result in wind and water leaks or damage to the the zipper but close only about 1 inch (2.5 cm).
Page 157 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 157 11. Continue closing the zipper only along the top edge front and working to the rear of the vehicle. Finish by of the window. closing the zipper completely and attaching the Velcro along the top and rear of the window. Repeat this step for the opposite side.
Page 158 158 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 13. Locate the black swing gate bar. Slide the swing gate 14. Install the rear window by starting both zipper ends bar over the receiver at the bottom inside of the rear at the lower left corner of the rear window opening. window.
Page 159 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 159 16. Grasp the swing gate bar and position it into the 18. Open the doors and insert the roof retainers into the swing gate brackets. channels above the door, starting at the front and work- ing rearward.
Page 160: Sunrider - 4 Door Models
160 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 19. Close the header latches and return the sun visors to SUNRIDER — 4 DOOR MODELS their secured position. NOTE: If you are going to be driving faster than 40 mph (64 km/h) with the Sunrider feature open, it is recom- mended that you remove the rear window of the vehicle.
Page 161 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 161 To Open 3. Release the header latches from the loops on the windshield frame. 1. Above the front of the rear door, place finger up into the cut out in the plastic retainer and pull down rolling both the front and rear retainers out of the door frame.
Page 162 162 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 4. Grasp the front side bow behind the header, and lift 5. Fold back the front section of the top, and gently rest the top. the header on top of the rear portion of the deck. I n f o r ma t i o n P r o v i d e d b y :...
Page 163 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 163 6. Fold the top material so that the plastic retainers form 8. Secure the top by using the two (2) provided straps. a “W” as shown. Enter the vehicle, and move the material Each strap will wrap around the side bow and Velcro to into two folds.
Page 164: Soft Top (4 Door Models)
164 UNDERSTANDING THE FEATURES OF YOUR VEHICLE If the temperature is below 72°F (24°C) and/or the top SOFT TOP (4 DOOR MODELS) has been folded down for a period of time, the top will CAUTION! appear to have shrunk when you raise it, making it difficult to put up.
Page 165 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 165 CAUTION! WARNING! • Do not drive vehicle with rear window curtain up • Do not run a fabric top through an automatic car wash. Window scratches and wax build up may result. unless side curtains are also open. Dangerous •...
Page 166: Folding Down The Soft Top
166 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Folding Down The Soft Top 1 — Header Bow 6 — Body Side Retainer 11 — Plastic Retainer 2 — 2 Bow 7 — Quarter Window 3 — 3 Bow 8 — Check Strap 4 —...
Page 167 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 167 1 — Zipper Start 2 — Zipper Finish 3 — Swing Gate Bar 4 — Swing Gate Brackets 5 — Sail Panels I n f o r ma t i o n P r o v i d e d b y :...
Page 168 168 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: Clean side and rear windows before removal to assist in preventing scratching during removal of the soft top. If zippers are difficult to operate due to road dust, etc., clean them with a mild soap solution and a small brush.
Page 169 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 169 4. Release the header latches and hooks from the loops 6. Before unzipping the rear window, release the first on the windshield frame. three (3) inches of both sail panels from the channel. Remove the swing gate bar by pulling it straight rear- ward out of the swing gate brackets.
Page 170 170 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • Unzip the rear window starting at the right lower 7. Undo the Velcro that runs along the top and rear corner of the window. Pull the zipper up, across the edge of the side window. top and down to the left lower corner.
Page 171 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 171 9. Once unzipped, remove side window retainers from NOTE: When releasing the sail panel retainers, it is the door channel and body side channel. Repeat this step helpful to pull down on the rear roof bow. on the opposite side.
Page 172 172 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 12. The swing gate brackets do not need to be removed 13. Grasp the front side bow behind the header, and lift unless the hard top is being installed. To remove the the top. swing gate brackets, pull the front of the bracket forward while rolling the entire bracket back in towards the vehicle to disengage.
Page 173 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 173 14. Fold back the front section of the top, and gently rest 15. Fold the top material so that the plastic retainers form the header on top of the rear portion of the deck. a “W”...
Page 174 174 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 16. Release the side bows by pressing down on the latch 17. Grasp the folded side bows and slide the top along above the front of the rear door. Push the top rearward to the door frame track to the rear door frame.
Page 175 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 175 18. Gently slide the side bows off the door frame track around the side bows and through the slot on the and lower the top down into the vehicle. bodyside retainer and Velcro back onto itself. Ensure that the top is secure.
Page 176: Putting Up The Soft Top
176 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Putting Up The Soft Top 1 — Header Bow 6 — Body Side Retainer 11 — Plastic Retainer 2 — 2 Bow 7 — Quarter Window 3 — 3 Bow 8 — Check Strap 4 —...
Page 177 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 177 1 — Zipper Start 2 — Zipper Finish 3 — Swing Gate Bar 4 — Swing Gate Brackets 5 — Sail Panels I n f o r ma t i o n P r o v i d e d b y :...
Page 178 178 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: Be extremely careful when putting up the soft top to prevent the doors from getting scratched. It may be helpful to open the rear doors. 1. Install the door frames, if removed. Refer to “Door Frame”...
Page 179 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 179 5. Insert the slider feature of the knuckles into the door 6. Ensure that the top locks into Sunrider locking mecha- frame tracks and slide the top forward. nisms that are located above the front of the rear doors. 7.
Page 180 180 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 8. Standing on the side of the vehicle, lift the top by the on the side bows above the front doors. They should side bow until it rests on the windshield frame. cradle the tubing. Finally, make sure that the check strap (the long, woven strap reaching from the rear bow to the 2 bow) does not get entangled in any of the framework when unfolding the top.
Page 181 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 181 10. Open the header latches and engage the hook on each over the channel until it snaps onto the exterior part of side onto the windshield loops (do not close the latches). the rail. To be properly located, the bracket must only be clipped to the shortened rail edge.
Page 182 182 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 13. Partially install the sail panel retainers into the body 14. To install the side windows, affix the window tem- side channel, leaving the last three (3) inches towards the porarily by attaching to the Velcro in the upper rear rear window loose (on both sides).
Page 183 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 183 15. Insert the front retainer of the window into the door 16. Continue closing the zipper only along the top edge channel, making sure the retainer is fully seated and of the window. properly positioned on the door frame.
Page 184 184 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 17. Insert the retainer along the bottom edge of the 18. Locate the black swing gate bar. Slide the swing gate window into the bottom side channel, beginning at the bar over the receiver at the bottom inside of the rear front and working to the rear of the vehicle.
Page 185 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 185 19. Install the rear window by starting both zipper ends 21. Grasp the swing gate bar and position it into the at the lower left corner of the rear window opening. swing gate brackets. Ensure that the zippers are properly started and aligned before zipping to prevent damage.
Page 186 186 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 23. Open the doors and insert the top retainers into the 24. Ensure plastic retainer is tucked in properly at channels in the door frame above the doors, starting at B-pillar not pinching seal. the front and work toward the rear of the vehicle.
Page 187: Folding Windshield
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 187 25. Close the header latches and return the sun visors to FOLDING WINDSHIELD their secured position. The fold down windshield and removable side bars on your vehicle are structural elements that can provide some protection in some accidents.
Page 188 188 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Raise the windshield and reinstall the side bars as soon as WARNING! the task that required their removal is completed and before you return to on-road driving. Both you and your Carefully follow these warnings to help protect against passenger should wear seat belts at all times, on-road and personal injury: off-road, regardless of whether the windshield is raised...
Page 189: Lowering The Windshield And Removing Side Bars
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 189 Lowering the Windshield and Removing Side Bars 1. Lower the fabric top or remove the hard top following the instructions in this manual. NOTE: To assist in properly reinstalling side bars, mark the original locations prior to removing. 2.
Page 190 190 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 4. Remove 1 hex bolt (13mm) visible through the plastic CAUTION! trim on bottom side of side bar, 1 hex bolt (13mm) on the side of the side bar, and 1 hex bolt (13mm) on top of the Do not remove the head impact foam from the side side bar.
Page 191 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 191 WARNING! You or others could be injured if you carry the side bars loose in your vehicle. Remove the bars from the vehicle or securely store them as described or they may cause personal injury if an accident occurs. See your authorized dealer for the cinch straps.
Page 192: Raising The Windshield And Replacing Side Bars
192 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 3. Attach front of side bar to windshield frame. Raising The Windshield And Replacing Side Bars • Install top two (2) hex bolts (13mm) first, then lower 1. Raise the windshield. side hex bolt (13mm). Lower side bolt will not align 2.
Page 193: Rear Window Features - Hard Top Only
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 193 5. Install the lower windshield plates with the 6 black REAR WINDOW FEATURES — HARD TOP ONLY round headed Torx head screws (using a #40 Torx head Rear Window Wiper/Washer — If Equipped driver) on each side of the base of the windshield.
Page 194 194 UNDERSTANDING THE FEATURES OF YOUR VEHICLE If the swing gate flip-up window is open or the swing gate is open, connection to the rear window wiper is interrupted preventing activation of the rear wiper blade. When the swing gate flip-up window or the swing gate is closed, the rear wiper switch or the ignition switch needs to be turned OFF, and then to ON to restart the rear wiper.
Page 195: Rear Window Defroster - If Equipped
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 195 level at regular intervals. Fill the reservoir with wind- The defroster will automatically turn off after about ten shield washer solvent (not radiator antifreeze) and oper- minutes. For five more minutes of operation, press the ate the system for a few seconds to flush out the residual switch again.
Page 196 I n f o r ma t i o n P r o v i d e d b y :...
Page 197: Understanding Your Instrument Panel
UNDERSTANDING YOUR INSTRUMENT PANEL CONTENTS ▫ Two Types Of Signals ....216 Instrument Panel And Controls ... . . 200 ▫...
Page 198 198 UNDERSTANDING YOUR INSTRUMENT PANEL ▫ Notes On Playing MP3/WMA Files ..228 ▫ Operating Instructions — Satellite Radio ..246 ▫ List Button (Disc Mode For MP3/WMA ▫ Clock Setting Procedure ....246 Play) .
Page 199 UNDERSTANDING YOUR INSTRUMENT PANEL 199 ▫ Manual Air Conditioning And Heating CD/DVD Disc Maintenance ....251 System — If Equipped ....254 Radio Operation And Cellular Phones .
Page 200: Instrument Panel And Controls
200 UNDERSTANDING YOUR INSTRUMENT PANEL INSTRUMENT PANEL AND CONTROLS I n f o r ma t i o n P r o v i d e d b y :...
Page 201: Instrument Cluster
UNDERSTANDING YOUR INSTRUMENT PANEL 201 INSTRUMENT CLUSTER I n f o r ma t i o n P r o v i d e d b y :...
Page 202: Instrument Cluster Description
202 UNDERSTANDING YOUR INSTRUMENT PANEL or the battery is low. Also, a chime will sound if the light INSTRUMENT CLUSTER DESCRIPTION Your vehicle is equipped with the instrument cluster comes back on. See your authorized dealer immediately. described on the following pages. 3.
Page 203 UNDERSTANDING YOUR INSTRUMENT PANEL 203 6. Front Axle Lock Indicator Light — If Equipped turned from the OFF to the ON position, and the light Indicates when the front axle lock has been will turn off after the engine is started. If the bulb does activated.
Page 204 204 UNDERSTANDING YOUR INSTRUMENT PANEL 11. Brake Warning Light 12. Anti-Lock (ABS) Warning Light After ignition is turned on, illuminates to indicate After ignition is turned on, illuminates to indicate function check at vehicle start-up. Indicates park- function check at vehicle start-up. If light remains ing brake is applied.
Page 205 UNDERSTANDING YOUR INSTRUMENT PANEL 205 14. Rear Axle Lock Indicator Light — If Equipped 17. Sentry Key/Security Alarm Indicator Light — If Indicates when the rear axle lock has been Equipped activated. Refer to “Sentry Key Immobilizer System” or “Vehicle Security Alarm”...
Page 206 206 UNDERSTANDING YOUR INSTRUMENT PANEL 20. 4WD Indicator Light — If Equipped 23. Tire Pressure Monitoring Telltale Light — If This light alerts the driver that the vehicle is in Equipped the four-wheel drive mode, and the front and Each tire, including the spare (if provided), rear driveshafts are mechanically locked to- should be checked monthly when cold and gether forcing the front and rear wheels to...
Page 207 UNDERSTANDING YOUR INSTRUMENT PANEL 207 can lead to tire failure. Under-inflation also reduces fuel CAUTION! efficiency and tire tread life, and may affect the vehicle’s handling and stopping ability. The TPMS has been optimized for the original equipment tires and wheels. TPMS pressures and Please note that the TPMS is not a substitute for proper warnings have been established for the tire size tire maintenance, and it is the driver’s responsibility to...
Page 208 208 UNDERSTANDING YOUR INSTRUMENT PANEL 24. Odometer/Trip Odometer Certain conditions such as a loose or missing gas cap, The odometer shows the total distance the vehicle has poor quality fuel, etc. may illuminate the light after been driven. engine start. The vehicle should be serviced if the light stays on through several typical driving styles.
Page 209 UNDERSTANDING YOUR INSTRUMENT PANEL 209 up on the accelerator and apply as little throttle as 29. Electronic Stability Program (ESP) Warning possible. Be sure to adapt your speed and driving to the Light/Brake Assist System (BAS) Warning Light prevailing road conditions. The “ESP/TCS Indicator The ESP/BAS warning light in the instrument Light”...
Page 210 210 UNDERSTANDING YOUR INSTRUMENT PANEL 30. Electronic Throttle Control (ETC) Warning Light — on briefly as a bulb check. If the light does not come on If Equipped during starting, have the system checked by an autho- This light informs you of a problem with the rized dealer.
Page 211: Compass And Trip Computer - If Equipped
UNDERSTANDING YOUR INSTRUMENT PANEL 211 The compass/trip computer, when the appropriate con- COMPASS AND TRIP COMPUTER — IF EQUIPPED ditions exist, will show the following messages in the This feature, located on the instrument cluster (speedom- odometer display: eter and tachometer), displays information on outside •...
Page 212: Trip Conditions
212 UNDERSTANDING YOUR INSTRUMENT PANEL Press and hold the left button (on the instrument cluster) Estimated Range (DTE) for 2 to 3 seconds to switch from English to Metric This display shows the estimated distance that can be displays. traveled with the fuel remaining in the tank. This esti- mated distance is based on the most recent trip informa- Reset tion: (Average Fuel Economy) x (Fuel Remaining)
Page 213: Compass Temperature Display
UNDERSTANDING YOUR INSTRUMENT PANEL 213 Trip A Shows the total distance traveled for trip A since the last Compass Calibration reset. The Automatic Compass Calibration feature eliminates the need for the operator intervention under normal Trip B Shows the total distance traveled for trip B since the last conditions.
Page 214: Setting Compass Variance
214 UNDERSTANDING YOUR INSTRUMENT PANEL After initial calibration, the compass will continue to under 5 mph (8 km/h) in an area free from large metal automatically update this calibration whenever the ve- objects until the CAL symbol is extinguished. hicle is in motion. When the CAL symbol no longer is displayed, the compass is calibrated and should display correct head- Manual Compass Calibration...
Page 215 UNDERSTANDING YOUR INSTRUMENT PANEL 215 symbol appears. The current variance value will also be displayed. To change the zone, press the left button once to increment the zone. The default is Zone 8. After Zone 15, the values will wrap around to Zone 1. When the correct zone is displayed (per the Zone map) for the zone that the vehicle is located in, wait for about 5 seconds, then the trip computer will store the variance value in...
Page 216: Radio General Information
216 UNDERSTANDING YOUR INSTRUMENT PANEL Outside Temperature Two Types of Signals If the outside temperature is more than 131°F (55°C), the There are two basic types of radio signals... AM or display will show 131°F (55°C). When the outside tem- Amplitude Modulation, in which the transmitted sound perature is less than 40°F ( 40°C), the display will...
Page 217: Fm Reception
UNDERSTANDING YOUR INSTRUMENT PANEL 217 FM Reception Because FM transmission is based on frequency varia- tions, interference that consists of amplitude variations can be filtered out, leaving the reception relatively clear, which is the major feature of FM radio. NOTE: The radio, steering wheel radio controls (if equipped), and 6 disc CD/DVD changer (if equipped) will remain active for up to 10 minutes after the ignition...
Page 218 218 UNDERSTANDING YOUR INSTRUMENT PANEL Power Switch/Volume Control (Rotary) SCAN Button (Radio Mode) Press the ON/VOL control to turn the radio ON. Press Pressing the SCAN button causes the tuner to search for the ON/VOL a second time to turn OFF the radio. the next listenable station, in AM, FM or Satellite (if equipped) frequencies, pausing for 5 seconds at each Electronic Volume Control...
Page 219 UNDERSTANDING YOUR INSTRUMENT PANEL 219 Phone Button (UConnect™ Hands Free Phone) — 3. After adjusting the hours, press the right side TUNE If Equipped control knob to set the minutes. The minutes will begin to Press this button to operate the Hand Free Phone (UCon- blink.
Page 220 220 UNDERSTANDING YOUR INSTRUMENT PANEL RW/FF (Radio Mode) Press the rotary TUNE control knob a third time and Pressing the rewind or fast forward button causes the TREBLE will display. Turn the TUNE control knob to the tuner to search for the next frequency in the direction of right or left to increase or decrease the Treble tones.
Page 221 UNDERSTANDING YOUR INSTRUMENT PANEL 221 allow the program format type to be selected. Many radio News News stations do not currently broadcast Music Type informa- Nostalgia Nostalga tion. Oldies Oldies Toggle the Music Type button to select the following Personality Persnlty format types: Public...
Page 222 222 UNDERSTANDING YOUR INSTRUMENT PANEL • DVD Enter - When the disc is in DVD Menu mode, By pressing the SEEK button when the Music Type icon is displayed, the radio will be tuned to the next frequency selecting DVD Enter will allow you to play the current station with the same selected Music Type name.
Page 223 UNDERSTANDING YOUR INSTRUMENT PANEL 223 • Angle – Repeatedly Pressing SELECT will change knob to adjust the hours and then press and turn the the viewing angle if supported by the DVD disc (If TUNE control knob to adjust the minutes. Press the Equipped).
Page 224 224 UNDERSTANDING YOUR INSTRUMENT PANEL disc). If customer wishes to select a language not listed, Audio DRC — If Equipped then scroll down and select other. Enter the country Selecting this item will allow the user to limit maximum code using the TUNE control knob to scroll up and down audio dynamic range - The default is set to High, and to select the # and then push to select.
Page 225 UNDERSTANDING YOUR INSTRUMENT PANEL 225 NOTE: The user will have to set these defaults before You may add a second station to each push-button by loading a disc. If changes are made to these settings after repeating the above procedure with this exception: Press a disc is loaded, changes will not be effective.
Page 226: Operation Instructions
226 UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: The ignition switch must be in the ON or ACC Operation Instructions - (DISC MODE for CD and MP3/WMA Audio Play, DVD-VIDEO) position to operate the radio. The radio DVD player and many DVD discs are coded by LOAD Button —...
Page 227 UNDERSTANDING YOUR INSTRUMENT PANEL 227 Eject Button — Ejecting Compact Disc(s) SCAN Button (CD MODE) Press the eject button and the push-button with Press the Scan button to scan through each track on the the corresponding number (1-6) where the CD CD currently playing.
Page 228: Notes On Playing Mp3/Wma Files
228 UNDERSTANDING YOUR INSTRUMENT PANEL RND Button (Random Play Button) (CD MODE) Supported Medium Formats (File Systems) Press this button while the CD is playing to activate The medium formats supported by the radio are ISO 9660 Random Play. This feature plays the selections on the Level 1 and Level 2 and includes the Joliet extension.
Page 229 UNDERSTANDING YOUR INSTRUMENT PANEL 229 Multisession disc formats are supported by the radio. frequencies in the following table are supported. In Multisession discs may contain combinations of normal addition, variable bit rates (VBR) are also supported. The CD audio tracks and computer files (including MP3/ majority of MP3/WMA files use a 44.1 kHz sampling rate WMA files).
Page 230: List Button (Disc Mode For Mp3/Wma Play)
230 UNDERSTANDING YOUR INSTRUMENT PANEL • Number of files and folders - Loading times will ID3 Tag information for artist, song title, and album title are supported for version 1 ID3 tags. ID3 version 2 is not increase with more files and folders supported by the radios.
Page 231: Info Button (Disc Mode For Mp3/Wma Play)
UNDERSTANDING YOUR INSTRUMENT PANEL 231 Pushing the AUX button will change the mode to auxil- INFO Button (DISC Mode for MP3/WMA Play) Pressing the INFO button repeatedly will scroll through iary device if the AUX jack is connected. the following TAG information: Song Title, Artist, File NOTE: The AUX device must be turned on and the Name, and Folder Name (if available).
Page 232 232 UNDERSTANDING YOUR INSTRUMENT PANEL TIME Button (Auxiliary Mode) Operating Instructions - Video Entertainment Press this button to change the display from elapsed System (VES ) (If Equipped) playing time to time of day. The time of day will display Refer to separate Video Entertainment System (VES ) Guide.
Page 233: Sales Code Res - Am/Fm Stereo Radio With Cd Player (Mp3 Aux Jack)
UNDERSTANDING YOUR INSTRUMENT PANEL 233 SALES CODE RES — AM/FM STEREO RADIO Operating Instructions - Radio Mode WITH CD PLAYER (MP3 AUX JACK) NOTE: The ignition switch must be in the ON or ACC NOTE: The radio sales code is located on the lower right position to operate the radio.
Page 234 234 UNDERSTANDING YOUR INSTRUMENT PANEL to seek up and the left switch to seek down. The radio If your vehicle is not equipped with this feature, a will remain tuned to the new station until you make “UConnect™ System Not Available” message will dis- another selection.
Page 235 UNDERSTANDING YOUR INSTRUMENT PANEL 235 Clock Setting Procedure INFO Button Press the INFO button for an RDS station (one with call 1. Press and hold the TIME button, until the hours blink. letters displayed). The radio will return a Radio Text 2.
Page 236 236 UNDERSTANDING YOUR INSTRUMENT PANEL Press the rotary TUNE control knob a second time and MUSIC TYPE Button MID will display. Turn the TUNE control knob to the Pressing this button once will turn on the Music Type mode for 5 seconds. Pressing the Music Type button or turning right or left to increase or decrease the Mid Range tones.
Page 237 UNDERSTANDING YOUR INSTRUMENT PANEL 237 By pressing the SEEK button when the Music Type icon Jazz Jazz is displayed, the radio will be tuned to the next frequency News News station with the same selected Music Type name. The Nostalgia Nostalga Music Type function only operates when in the FM Oldies...
Page 238 238 UNDERSTANDING YOUR INSTRUMENT PANEL AM and FM Buttons stations to be stored into push-button memory. The Press the buttons to select AM or FM Modes. stations stored in SET 2 memory can be selected by pressing the push-button twice. SET Button —...
Page 239: Operation Instructions - Cd Mode For Cd And Mp3 Audio Play
UNDERSTANDING YOUR INSTRUMENT PANEL 239 begin to play when you insert the disc. The display will Operation Instructions - CD MODE for CD and MP3 Audio Play show the disc number, the track number, and index time in minutes and seconds. Play will begin at the start of NOTE: The ignition switch must be in the ON or ACC track 1.
Page 240 240 UNDERSTANDING YOUR INSTRUMENT PANEL EJECT Button - Ejecting a CD the current selection. Pressing and holding the SEEK Press the EJECT button to eject the CD. button will allow to scroll through tracks faster in CD, MP3 modes. SCAN Button Press the Scan button to scan through each track on the If you have ejected a disc and have not removed it within CD currently playing.
Page 241: Notes On Playing Mp3 Files
UNDERSTANDING YOUR INSTRUMENT PANEL 241 AM or FM Button Supported Media (Disc Types) Switches the Radio to the Radio mode. The MP3 file recording media supported by the radio are CDDA, CD-R, CD-RW, MP3, and CDDA+MP3. RND Button (Random Play Button) Press this button while the CD is playing to activate Supported Medium Formats (File Systems) Random Play.
Page 242 242 UNDERSTANDING YOUR INSTRUMENT PANEL a number instead. With a maximum number of files, Supported MP3 File Formats exceeding 20 folders will result in this display. With The radio will recognize only files with the *.MP3 exten- 200 files, exceeding 50 folders will result in this sion as MP3 files.
Page 243 UNDERSTANDING YOUR INSTRUMENT PANEL 243 Playback of MP3 Files MPEG Sampling Fre- Bit Rate (kbps) When a medium containing MP3 data is loaded, the Specification quency (kHz) radio checks all files on the medium. If the medium 320, 256, 224, contains a lot of folders or files, the radio will take more MPEG-1 Audio 192, 160, 128,...
Page 244: List Button (Cd Mode For Mp3 Play)
244 UNDERSTANDING YOUR INSTRUMENT PANEL Press and hold the INFO button again for 3 seconds to LIST Button (CD Mode for MP3 Play) Pressing the LIST button will bring up a list of all folders return to elapsed time display. on the disc.
Page 245: Sales Code Rer - Am/Fm/Cd/Dvd Radio With Navigation System - If Equipped
UNDERSTANDING YOUR INSTRUMENT PANEL 245 TIME Button (Auxiliary Mode) SALES CODE RER — AM/FM/CD/DVD RADIO Press this button to change the display to time of day. The WITH NAVIGATION SYSTEM — IF EQUIPPED time of day will display for 5 seconds (when ignition is NOTE: The radio sales code is located on the lower right off).
Page 246: Operating Instructions - Satellite Radio
246 UNDERSTANDING YOUR INSTRUMENT PANEL either the H button on the faceplate to change the hour or Operating Instructions — Satellite Radio Refer to your “Navigation User’s Manual” for detailed the M button on the faceplate to change the minute. operating instructions.
Page 247: Satellite Radio - If Equipped
UNDERSTANDING YOUR INSTRUMENT PANEL 247 3. Highlight the appropriate time zone for you location SATELLITE RADIO — IF EQUIPPED and press ENTER to store your selection. Select “Done” Satellite radio uses direct satellite to receiver broadcast- when finished. ing technology to provide clear digital sound, coast to coast.
Page 248: Electronic Serial Number/Sirius Identification Number (Ens/Sid)
248 UNDERSTANDING YOUR INSTRUMENT PANEL 1. The Electronic Serial Number/Sirius Identification Selecting Satellite Mode (RSC Radios) Number (ESN/SID). Press the SAT button until SAT appears in the display. A CD may remain in the radio while in the Satellite radio 2.
Page 249: Operating Instructions - Satellite Mode
UNDERSTANDING YOUR INSTRUMENT PANEL 249 • Dense tree coverage may interrupt reception in the SCAN Button form of short audio mutes. Pressing the SCAN button causes the tuner to search for the next channel, pausing for 8 seconds before continuing •...
Page 250 250 UNDERSTANDING YOUR INSTRUMENT PANEL TUNE Control (Rotary) SETUP Button Turn the right side rotary control clockwise to increase or Pressing the SETUP button allows you to select the counter-clockwise to decrease the channel. following items: • Display Sirius ID number — Press the SELECT button MUSIC TYPE Button Pressing this button once will turn on the Music Type to display the Sirius ID number.
Page 251: Operating Instructions - Hands Free Phone
UNDERSTANDING YOUR INSTRUMENT PANEL 251 the SET button twice and SET 2 will show in the display Operating Instructions - Video Entertainment window. Each button can be set for SET 1 and SET 2. This System (VES ) (If Equipped) allows a total of 12 Satellite channels to be stored into Refer to separate Video Entertainment System (VES ) Guide.
Page 252: Radio Operation And Cellular Phones
252 UNDERSTANDING YOUR INSTRUMENT PANEL 6. Do not expose the disc to direct sunlight. CLIMATE CONTROLS 7. Do not store the disc where temperatures may become Manual Heater Only too high. The controls for the heating/ventilation system in this vehicle consist of a series of rotary knobs. These comfort RADIO OPERATION AND CELLULAR PHONES controls can be set to obtain desired interior conditions.
Page 253 UNDERSTANDING YOUR INSTRUMENT PANEL 253 Mode Control Floor The mode control (left rotary knob) allows you to choose Air is directed through the floor outlets and side from several patterns of air distribution. You can select window demist outlets with a small amount either a primary mode, as identified by the symbols, or a through the defrost outlet.
Page 254: System - If Equipped
254 UNDERSTANDING YOUR INSTRUMENT PANEL you select. The fan speed increases as you move the control to the right from the OFF position. Temperature Control Use this control (right rotary knob) to regulate the temperature of the air inside the passenger compartment. The blue area of the scale indicates cooler temperatures while the red area indicates warmer temperatures.
Page 255 UNDERSTANDING YOUR INSTRUMENT PANEL 255 Mode Control Bi-Level The mode control allows you Air is directed through the panel and floor outlets. to choose from several pat- terns of air distribution. You NOTE: There is a difference in temperature between the can select either a primary upper and lower outlets for added comfort.
Page 256 256 UNDERSTANDING YOUR INSTRUMENT PANEL Defrost Blower Control Air is directed through the windshield and side Use this control to regulate window demist outlets. Use this mode with maxi- the amount of air forced mum fan and temperature settings for best windshield through the system in any and side window defrosting.
Page 257 UNDERSTANDING YOUR INSTRUMENT PANEL 257 Temperature Control Circulation Control Use this control to regulate Press this button to choose the temperature of the air in- between outside air intake or side the passenger compart- recirculation of the air inside ment. The blue area of the the vehicle.
Page 258: Operating Tips
258 UNDERSTANDING YOUR INSTRUMENT PANEL moisture build up inside the vehicle. For maximum Operating Tips defogging, select the Outside Air position. Window Fogging NOTE: The “Recirculate” mode will not operate in floor, Windows will fog on the inside when the humidity inside mix or defrost modes.
Page 259 UNDERSTANDING YOUR INSTRUMENT PANEL 259 smoke, perfumes, etc.) from sticking to the windows. Winter Operation Contaminates increase the rate of window fogging. When operating the system during the winter months, make sure the air intake, located directly in front of the Summer Operation windshield, is free of ice, slush, snow, or other obstruc- Air conditioned vehicles must be protected with a high...
Page 260 I n f o r ma t i o n P r o v i d e d b y :...
Page 261: Starting And Operating
STARTING AND OPERATING CONTENTS Starting Procedures ..... 265 Manual Transmission ....269 ▫...
Page 262 262 STARTING AND OPERATING ▫ Shift Positions ......282 ▫ Traction Downhill ..... 293 ▫...
Page 263 STARTING AND OPERATING 263 ▫ Radial-Ply Tires ..... . 312 ▫ Reformulated Gasoline ....322 ▫...
Page 264 264 STARTING AND OPERATING ▫ Trailer Towing Weights (Maximum Trailer Recreational Towing (Behind Motorhome, Etc.) . . 346 Weight Ratings) ..... . 335 ▫...
Page 265: Starting Procedures
STARTING AND OPERATING 265 4WD Models Only STARTING PROCEDURES Before starting your vehicle, adjust your seat, adjust both In 4L mode, this vehicle will start regardless of whether inside and outside mirrors, and fasten your seat belts. or not the clutch pedal is pressed to the floor. This feature enhances off-road performance by allowing the vehicle to WARNING! start when in 4L without having to depress the clutch...
Page 266: Extreme Cold Weather (Below -20°F Or -29°C)
266 STARTING AND OPERATING Tip Start Feature — Automatic Transmission Only Extreme Cold Weather (below –20°F or –29°C) Do not press the accelerator. Turn the ignition key briefly To insure reliable starting at these temperatures, use of an to START position, and release it. The starter motor will externally powered electric engine block heater (available continue to run, but will automatically disengage itself from your dealer) is recommended.
Page 267 STARTING AND OPERATING 267 CAUTION! WARNING! To prevent damage to the starter, do not crank the Do not attempt to push or tow your vehicle to get it engine for more than 15 seconds at a time. Wait 10 to started.
Page 268: After Starting
268 STARTING AND OPERATING If the engine has been flooded, it may start to run, but not WARNING! have enough power to continue running when the key is released. If this occurs, continue cranking with the accel- Never leave children alone in a vehicle. Leaving erator pedal pushed all the way to the floor.
Page 269: Engine Block Heater - If Equipped
STARTING AND OPERATING 269 ENGINE BLOCK HEATER — IF EQUIPPED MANUAL TRANSMISSION The engine block heater warms engine coolant and 6-Speed Manual Transmission permits quicker starts in cold weather. Connect the cord to a standard 110-115 volt AC electrical outlet with a WARNING! grounded, three wire extension cord.
Page 270 270 STARTING AND OPERATING Follow the shift pattern on the gearshift knob. WARNING! NOTE: The backup lights will come on when your When parking your vehicle, always leave a manual vehicle is in R (Reverse) gear and the ignition is in the ON transmission in first gear and apply the parking position.
Page 271 STARTING AND OPERATING 271 • Do not operate at sustained high engine or road • When “rocking” a stuck vehicle by shifting between a speeds in lower gears. Engine damage may result. forward gear and reverse, do not spin wheels faster than 15 mph (24 km/h), or drivetrain damage may •...
Page 272 272 STARTING AND OPERATING Recommended Manual Transmission Downshifting CAUTION! Speeds To prevent clutch and transmission damage, your vehicle Failure to follow the recommended downshifting should be downshifted at speeds no greater than those speeds may cause the engine to over speed and/or listed in the chart below: damage the clutch disc even if the clutch pedal is Manual Transmission Downshift Speeds in MPH...
Page 273: Automatic Transmission
STARTING AND OPERATING 273 AUTOMATIC TRANSMISSION WARNING! CAUTION! It is dangerous to shift the selector lever out of P (Park) or N (Neutral) if the engine speed is higher Damage to the transmission may occur if the follow- than idle speed. If your foot is not firmly on the ing precautions are not observed: brake pedal, the vehicle could accelerate quickly •...
Page 274: Shift Lock Manual Override
274 STARTING AND OPERATING Shift Lock Manual Override Your vehicle may be equipped with a shift lock manual override. The manual override may be used in the event that the shift lever should fail to move from Park with the key in the ON position and the brake pedal depressed.
Page 275: Brake/Transmission Interlock System
STARTING AND OPERATING 275 Brake/Transmission Interlock System This system prevents you from moving the gear shift out of P (Park) and into any gear unless the brake pedal is pressed. This system is active only while the ignition switch is in the ON position. Always depress the brake pedal first, before moving the gear selector out of P (Park).
Page 276 276 STARTING AND OPERATING Gear Ranges WARNING! DO NOT race the engine when shifting from P (Park) or N (Neutral) position into another gear range. It is dangerous to shift the selector lever out of P (Park) or N (Neutral) if the engine speed is higher P (Park) than idle speed.
Page 277 STARTING AND OPERATING 277 R (Reverse) Overdrive (O/D) Use this range only after the vehicle has come to a For most city and highway driving. The transmission complete stop. contains an electronically controlled Overdrive, and will automatically shift from D (Drive) to O/D (Overdrive) if N (Neutral) the following conditions are present: Shift into N (Neutral) when the vehicle is standing for...
Page 278 278 STARTING AND OPERATING When frequent transmission shifting occurs while using Overdrive can be locked out by pressing the O/D OFF Overdrive, such as when operating the vehicle under switch located on the center console. The O/D OFF heavy load conditions (for example, in hilly terrain, indicator light (on the switch) will illuminate to show strong head winds, or trailer towing), turning off over- that the switch has been activated.
Page 279 STARTING AND OPERATING 279 WARNING! CAUTION! • Before moving the shift lever out of P (Park), you Never use P (Park) position with an automatic trans- mission as a substitute for the parking brake. Always must turn the ignition from LOCK so the steering apply parking brake fully when parked to guard wheel and shift lever are released.
Page 280: Four-Wheel Drive Operation
280 STARTING AND OPERATING Torque Converter Clutch A feature designed to improve fuel economy has been added to the automatic transmission of this vehicle. A clutch within the torque converter engages automatically at calibrated speeds. This may result in a slightly differ- ent feeling or response during normal operation in high gear.
Page 281 STARTING AND OPERATING 281 This transfer case is intended to be driven in the two NOTE: Do not attempt to make a shift while only the wheel drive (2H) position for normal street and highway front or rear wheels are spinning. The transfer case is not conditions such as hard surfaced roads.
Page 282: Shift Positions
282 STARTING AND OPERATING 2H Position WARNING! Rear Wheel Drive High Range — Normal street and highway driving. Hard surfaced roads. You or others could be injured if you leave the vehicle unattended with the transfer case in the N 4H Position (Neutral) position without first fully engaging the Four Wheel Drive High Range —...
Page 283: Shifting Procedure
STARTING AND OPERATING 283 The “4WD Indicator Light” (located in the instrument Shifting Procedure cluster) will illuminate when the transfer case is shifted 2H to 4H or 4H to 2H into the 4H position. Shifting between 2H and 4H can be made with the vehicle stopped or in motion.
Page 284: Trac-Lok™ Rear Axle - If Equipped
284 STARTING AND OPERATING NOTE: Pausing in transfer case N (Neutral) in vehicles WARNING! equipped with an automatic transmission may require shutting the engine OFF to avoid gear clash while Failure to engage a position completely can cause completing the shift. If difficulty occurs, shift the auto- transfer case damage or loss of power and vehicle matic transmission to N (Neutral), hold foot on brake, control.
Page 285: Axle Lock (Tru-Lok™) - Rubicon Models
STARTING AND OPERATING 285 Trac-Lok™ is especially helpful during slippery driving AXLE LOCK (TRU–LOK™) — RUBICON MODELS conditions. With both rear wheels on a slippery surface, a The axle lock switch is located on the lower switch bank slight application of the accelerator will supply maxi- (below the climate controls).
Page 286: Rear Axle Lock - 4Wd Non-Rubicon Models (If Equipped)
286 STARTING AND OPERATING This feature will only activate when the following con- REAR AXLE LOCK — 4WD NON-RUBICON ditions are met: MODELS (IF EQUIPPED) The rear axle lock switch is located on the lower switch • Key in ignition, vehicle in 4L (Low) range. bank (below the climate controls).
Page 287: Electronic Sway Bar Disconnect - If Equipped
STARTING AND OPERATING 287 ELECTRONIC SWAY BAR DISCONNECT — IF EQUIPPED Your vehicle may be equipped with an electronic discon- necting stabilizer/sway bar. This system allows greater front suspension travel in off-road situations. This system is controlled by the electronic control sway bar switch located on the lower switch bank (below the climate controls).
Page 288 288 STARTING AND OPERATING when activation conditions are not met. The stabilizer/ To disconnect the stabilizer/sway bar, shift to either 4HI sway bar should remain in on-road mode during normal or 4LO (refer to “Four Wheel Drive Operation” in this driving conditions.
Page 289: On-Road Driving Tips
STARTING AND OPERATING 289 An advantage of the higher ground clearance is a better WARNING! view of the road, allowing you to anticipate problems. They are not designed for cornering at the same speeds as If the stabilizer/sway bar will not return to on-road conventional 2-wheel drive vehicles any more than low- mode, vehicle stability is greatly reduced.
Page 290: Off-Road Driving Tips
290 STARTING AND OPERATING OFF-ROAD DRIVING TIPS NOTE: Prior to off-road usage, the side step (if equipped) should be removed to prevent damage. 1. Remove two (2) nuts from bodyside. 3. Remove side step assembly. When To Use 4L (Low) Range When off-road driving, shift to 4L (Low) for additional traction and control on slippery or difficult terrain, ascending or descending steep hills, and to increase low...
Page 291: Driving Through Water
STARTING AND OPERATING 291 extreme situations such as deep snow, mud, steep in- Driving through water more than a few inches deep will clines, or sand where additional low speed pulling power require extra caution to ensure safety and prevent dam- is needed.
Page 292: Driving In Snow, Mud And Sand
292 STARTING AND OPERATING Standing Water Do not shift to a lower gear than necessary to maintain Avoid driving in standing water deeper than 20 inches, headway. Over-revving the engine can spin the wheels and reduce speed appropriately to minimize wave ef- and traction will be lost.
Page 293: Traction Downhill
STARTING AND OPERATING 293 your speed. If the brakes are required to control vehicle turning the front wheels slowly left and right. This may speed, apply them lightly and avoid locking or skidding provide a fresh “bite” into the surface and will usually the tires.
Page 294: After Driving Off-Road
294 STARTING AND OPERATING • After extended operation in mud, sand, water, or After Driving Off-Road Off-road operation puts more stress on your vehicle than similar dirty conditions, have brake rotors, wheels, does most on-road driving. After going off-road it is brake linings, and axle yokes inspected and cleaned as always a good idea to check for damage.
Page 295: Parking Brake
STARTING AND OPERATING 295 PARKING BRAKE To set the parking brake, pull the lever up as firmly as possible. When the parking brake is applied with the ignition ON, the “Brake Warning Light” in the instru- ment cluster will light. To release the parking brake, pull up slightly, press the center button, then lower the lever completely.
Page 296: Anti-Lock Brake System
296 STARTING AND OPERATING (Park), otherwise the load on the transmission locking When parking on a hill, turn the front wheels toward the mechanism may make it difficult to move the selector out curb on a downhill grade and away from the curb on an of P (Park).
Page 297 STARTING AND OPERATING 297 During off-road use, loss of traction can temporarily WARNING! defeat the system and cause the warning light to illumi- nate. Turn the ignition OFF and ON again to restore Significant over or under-inflation of tires, or mixing Anti-Lock Brake System function.
Page 298: Power Steering
298 STARTING AND OPERATING WARNING! CAUTION! • Anti-lock system (ABS) cannot prevent the natural The Anti-Lock Brake System is subject to possible laws of physics from acting on the vehicle, nor can detrimental effects of electronic interference caused it increase braking or steering efficiency beyond by improperly installed aftermarket radios or that afforded by the condition of the vehicle telephones.
Page 299 STARTING AND OPERATING 299 If for some reason the power assist is interrupted, it will WARNING! still be possible to steer your vehicle. Under these condi- tions, you will observe a substantial increase in steering Continued operation with reduced power steering effort, especially at very low vehicle speeds and during assist could pose a safety risk to yourself and others.
Page 300: Tire Safety Information
300 STARTING AND OPERATING • European Metric tire sizing is based on European TIRE SAFETY INFORMATION design standards. Tires designed to this standard have Tire Markings the tire size molded into the sidewall beginning with the section width. The letter P is absent from this tire size designation.
Page 301 STARTING AND OPERATING 301 Tire Sizing Chart EXAMPLE: Size Designation: P = Passenger car tire size based on U.S. design standards ..blank..= Passenger car tire based on European design standards LT = Light Truck tire based on U.S. design standards T = Temporary Spare tire 31 = Overall Diameter in Inches (in) 215 = Section Width in Milimeters (mm)
Page 302 302 STARTING AND OPERATING EXAMPLE: Service Description: 95 = Load Index —A numerical code associated with the maximum load a tire can carry. H = Speed Symbol —A symbol indicating the range of speeds at which a tire can carry a load corresponding to its load index under certain operating conditions.
Page 303: Tire Identification Number (Tin)
STARTING AND OPERATING 303 Look for the TIN on the outboard side of black sidewall Tire Identification Number (TIN) tires as mounted on the vehicle. If the TIN is not found on The TIN may be found on one or both sides of the tire the outboard side then you will find it on the inboard side however the date code may only be on one side.
Page 304: Tire Loading And Tire Pressure
304 STARTING AND OPERATING Tire Loading and Tire Pressure Tire Placard Location Tire Placard Location (4 Door Models) Tire Placard Location (2 Door Models) I n f o r ma t i o n P r o v i d e d b y :...
Page 305 STARTING AND OPERATING 305 Tire and Loading Information Placard Loading The vehicle maximum load on the tire must not exceed the load carrying capacity of the tire on your vehicle. You will not exceed the tire’s load carrying capacity if you adhere to the loading conditions, tire size and cold tire inflation pressures specified on the Tire and Loading Information placard and the Vehicle Loading section of...
Page 306 306 STARTING AND OPERATING combined weight of occupants, cargo/luggage and 5. Determine the combined weight of luggage and cargo trailer tongue weight (if applicable) should never exceed being loaded on the vehicle. That weight may not safely the weight referenced here. exceed the available cargo and luggage load capacity calculated in step 4.
Page 307 STARTING AND OPERATING 307 I n f o r ma t i o n P r o v i d e d b y :...
Page 308: Tires - General Information
308 STARTING AND OPERATING 1. Safety— WARNING! WARNING! Overloading of your tires is dangerous. Overloading can cause tire failure, affect vehicle handling, and Improperly inflated tires are dangerous and can cause increase your stopping distance. Use tires of the accidents. recommended load capacity for your vehicle.
Page 309: Tire Inflation Pressures
STARTING AND OPERATING 309 2. Economy— Tire Inflation Pressures Improper inflation pressures can cause uneven wear patterns to develop across the tire tread. These abnormal wear patterns will reduce tread life resulting in a need for earlier tire replacement. Under inflation also increases tire rolling resistance and results in higher fuel consump- tion.
Page 310 310 STARTING AND OPERATING CAUTION! After inspecting or adjusting the tire pressure always reinstall the valve stem cap–if equipped. This will prevent moisture and dirt from entering the valve stem, which could damage the valve stem. Inflation pressures specified on the placard are always “cold tire inflation pressure”.
Page 311: Tire Pressures For High Speed Operation
STARTING AND OPERATING 311 Tire pressures change by approximately 1 psi (7 kPa) per speeds, maintaining correct tire inflation pressure is very 12° F (7° C) of air temperature change. Keep this in mind important. Increased tire pressure and reduced vehicle when checking tire pressure inside a garage especially in loading may be required for high speed vehicle opera- the winter.
Page 312: Radial-Ply Tires
312 STARTING AND OPERATING Radial-Ply Tires WARNING! WARNING! Fast spinning tires can be dangerous. Forces gener- ated by excessive wheel speeds may cause tire dam- Combining radial ply tires with other types of tires age or failure. A tire could explode and injure some- on your vehicle will cause your vehicle to handle one.
Page 313: Life Of Tire
STARTING AND OPERATING 313 Life of Tire The service life of a tire is dependent upon varying factors including but not limited to: • Driving style • Tire pressure • Distance driven WARNING! Tires and spare tire should be replaced after six years, regardless of the remaining tread.
Page 314: Replacement Tires
314 STARTING AND OPERATING Keep unmounted tires in a cool, dry place with as little WARNING! exposure to light as possible. Protect tires from contact with oil, grease and gasoline. • Do not use a tire, wheel size or rating other than that specified for your vehicle.
Page 315: Alignment And Balance
STARTING AND OPERATING 315 Improper alignment will not cause vehicle vibration. CAUTION! Vibration may be a result of tire and wheel out-of- balance. Proper balancing will reduce vibration and Replacing original tires with tires of a different size avoid tire cupping and spotty wear. may result in false speedometer and odometer readings.
Page 316: Tire Rotation Recommendations
316 STARTING AND OPERATING • Install chains snugly and tighten after.6 mile (1 km) of Follow the recommended tire rotation frequency for your driving. type of driving found in the “Maintenance Schedules” Section of this manual. More frequent rotation is permis- •...
Page 317: Tire Pressure Monitor System (Tpms) - If Equipped
STARTING AND OPERATING 317 The TPM System will warn the driver of a low tire TIRE PRESSURE MONITOR SYSTEM (TPMS) — IF EQUIPPED pressure if the tire pressure falls below the low pressure The Tire Pressure Monitoring System (TPMS) will warn warning threshold for any reason, including low tem- the driver of a low tire pressure based on the vehicle perature effects.
Page 318: Base System - If Equipped
318 STARTING AND OPERATING (241 kPa). If the ambient temperature is 65°F (18°C) and NOTE: It is particularly important, for you to check the the measured tire pressure is 30 psi (207 kPa), a tempera- tire pressure in all of your tires regularly and to maintain ture drop to 20°F (-7°C) will decrease the tire pressure to the proper pressure.
Page 319 STARTING AND OPERATING 319 The “Tire Pressure Monitoring Telltale Light” will The “Tire Pressure Monitoring Telltale Light” will flash illuminate in the instrument cluster, and an au- on and off for 60 seconds, and an audible chime will dible chime will be activated when one or more of sound when a system fault is detected.
Page 320 320 STARTING AND OPERATING CAUTION! CAUTION! The TPMS has been optimized for the original After inspecting or adjusting the tire pressure always equipment tires and wheels. TPMS pressures have reinstall the valve stem cap. This will prevent mois- been established for the tire size equipped on your ture and dirt from entering the valve stem, which vehicle.
Page 321: General Information
STARTING AND OPERATING 321 Under-inflation also reduces fuel efficiency and tire The tire pressure sensors are covered under one of the tread life, and may affect the vehicle’s handling and following licenses: stopping ability. United States ..... KR5S120123 •...
Page 322: Reformulated Gasoline
322 STARTING AND OPERATING Light spark knock at low engine speeds is not harmful to Reformulated Gasoline your engine. However, continued heavy spark knock at Many areas of the country require the use of cleaner high speeds can cause damage and immediate service is burning gasoline referred to as “Reformulated Gasoline.”...
Page 323: Mmt In Gasoline
STARTING AND OPERATING 323 to reduce spark plug life and reduce emission system CAUTION! performance in some vehicles. The manufacturer recom- mends using gasolines without MMT. Since the MMT DO NOT use gasolines containing Methanol or E85 content of gasoline may not be indicated on the pump, Ethanol.
Page 324: Fuel System Cautions
324 STARTING AND OPERATING products contain high concentrations of methanol. Fuel System Cautions Fuel system damage or vehicle performance problems CAUTION! resulting from the use of such fuels or additives is not the responsibility of the manufacturer. Follow these guidelines to maintain your vehicle’s NOTE: Intentional tampering with emissions control performance: systems can result in civil penalties being assessed...
Page 325: Adding Fuel
STARTING AND OPERATING 325 garage, and never sit in a parked vehicle with the ADDING FUEL engine running for an extended period. If the vehicle is Fuel Filler Cap (Gas Cap) stopped in an open area with the engine running for The gas cap is located on the driver’s side of the vehicle.
Page 326 326 STARTING AND OPERATING CAUTION! CAUTION! Damage to the fuel system or emission control sys- To avoid fuel spillage and overfilling, do not “top tem could result from using an improper fuel cap off” the fuel tank after filling. (gas cap). A poorly fitting cap could let impurities into the fuel system.
Page 327 STARTING AND OPERATING 327 NOTE: Tighten the gas cap about 1/4 turn until you CAUTION! hear one click. This is an indication that cap is properly tightened. Damage to the fuel system or emission control sys- tem could result from using an improper fuel tank If the gas cap is not tighten properly, the Malfunction filler cap (gas cap).
Page 328: Vehicle Loading
328 STARTING AND OPERATING tongue weight, and cargo. The label also specifies maxi- VEHICLE LOADING mum capacities of front and rear axle systems (GAWR). Certification Label Total load must be limited so GVWR and front and rear As required by National Highway Traffic Safety Admin- GAWR are not exceeded.
Page 329 STARTING AND OPERATING 329 Tire Size Loading The tire size on the Label represents the actual tire size on The actual total weight and the weight of the front and your vehicle. Replacement tires must be equal to the load rear of your vehicle at the ground can best be determined capacity of this tire size.
Page 330: Trailer Towing
330 STARTING AND OPERATING Improper weight distributions can have an adverse effect TRAILER TOWING on the way your vehicle steers and handles and the way In this section you will find safety tips and information the brakes operate. on limits to the type of towing you can reasonably do with your vehicle.
Page 331 STARTING AND OPERATING 331 Gross Trailer Weight (GTW) Gross Axle Weight Rating (GAWR) The Gross Trailer Weight (GTW) is the weight of the The GAWR is the maximum capacity of the front and rear trailer plus the weight of all cargo, consumables and axles.
Page 332 332 STARTING AND OPERATING Frontal Area Weight-Distributing Hitch The maximum height and maximum width of the front of A weight-distributing system works by applying lever- a trailer. age through spring (load) bars. They are typically used for heavier loads, to distribute trailer tongue weight to Trailer Sway Control the tow vehicle’s front axle and the trailer axle(s).
Page 333 STARTING AND OPERATING 333 WARNING! An improperly adjusted Weight Distributing Hitch system may reduce handling, stability, braking per- formance, and could result in an accident. Weight Distributing Systems may not be compatible with Surge Brake Couplers. Consult with your hitch and trailer manufacturer or a reputable Recreational Vehicle dealer for additional information.
Page 334: Trailer Hitch Classification
334 STARTING AND OPERATING Refer to the Trailer Towing Weights (Maximum Trailer Weight Ratings) chart for the Max. GTW towable for your given drivetrain. Trailer Hitch Classification Class Max. GTW (Gross Trailer Wt.) Class I - Light Duty 2,000 lbs (907 kg) Class II - Medium 3,500 lbs (1 587 kg) Duty...
Page 335: Trailer Towing Weights (Maximum Trailer Weight Ratings)
STARTING AND OPERATING 335 Trailer Towing Weights (Maximum Trailer Weight Ratings) The following chart provides the maximum trailer weight ratings towable for your given drivetrain. Engine/ Axle Model GCWR (Gross Frontal Area Max. GTW (Gross Max. Tongue Wt. Transmis- Combined Wt. Trailer Wt.) (See Note 1) sion...
Page 336 336 STARTING AND OPERATING Engine/ Axle Model GCWR (Gross Frontal Area Max. GTW (Gross Max. Tongue Wt. Transmis- Combined Wt. Trailer Wt.) (See Note 1) sion Rating) 3.8L/ 4.10 2 Door Rubicon 6,243 lbs (2 832 kg) 25 sq. ft. (2.32 2,000 lbs (907 kg) 200 lbs (91 kg) Automatic...
Page 337 STARTING AND OPERATING 337 Engine/ Axle Model GCWR (Gross Frontal Area Max. GTW (Gross Max. Tongue Wt. Transmis- Combined Wt. Trailer Wt.) (See Note 1) sion Rating) 3.8L/ 4.10 4 Door X Model 7,830 lbs (3 552 kg) 32 sq. ft. (2.97 3,500 lbs (1 587 kg) 350 lbs (159 kg) Manual...
Page 338: Trailer And Tongue Weight
338 STARTING AND OPERATING NOTE: The trailer tongue weight must be considered as part of the combined weight of occupants and cargo, and should never exceed the weight referenced on the Tire and Loading Information placard. Refer to the Tire– Safety Information section in this manual.
Page 339: Towing Requirements
STARTING AND OPERATING 339 Consider the following items when computing the Towing Requirements weight on the rear axle of the vehicle: To promote proper break-in of your new vehicle driv- etrain components the following guidelines are recom- • The tongue weight of the trailer. mended: •...
Page 340 340 STARTING AND OPERATING • Safety chains must always be used between your WARNING! vehicle and trailer. Always connect the chains to the frame or hook retainers of the vehicle hitch. Cross the Improper towing can lead to an injury accident. chains under the trailer tongue and allow enough Follow these guidelines to make your trailer towing slack for turning corners.
Page 341 STARTING AND OPERATING 341 2. GTW − Check for signs of tire wear or visible tire damage before towing a trailer. Refer to the Tires–General 3. GAWR Information section of this manual on Tread Wear 4. Tongue weight rating for the trailer hitch utilized Indicators for the proper inspection procedure.
Page 342 342 STARTING AND OPERATING actuated brakes. When towing a trailer equipped with WARNING! a hydraulic surge actuated brake system, an electronic brake controller is not required. Do not connect trailer brakes to your vehicle’s hy- draulic brake lines. It can overload your brake sys- −...
Page 343 STARTING AND OPERATING 343 Towing Requirements — Trailer Lights & Wiring Whenever you pull a trailer, regardless of the trailer size, stop lights and turn signals on the trailer are required for motoring safety. The Trailer Tow Package may include a 4 and 7 pin wiring harness.
Page 344: Towing Tips
344 STARTING AND OPERATING Towing Tips Before setting out on a trip, practice turning, stopping and backing the trailer in an area away from heavy traffic. If using a manual transmission vehicle for trailer towing, all starts must be in FIRST gear to avoid excessive clutch slippage.
Page 345 STARTING AND OPERATING 345 The automatic transmission fluid and filter should be − When using the speed control, if you experience speed changed if you REGULARLY tow a trailer for more than drops greater than 10 mph (16 km/h), disengage until 45 minutes of continuous operation.
Page 346: Recreational Towing (Behind Motorhome, Etc.)
346 STARTING AND OPERATING RECREATIONAL TOWING (BEHIND Towing – 4WD Models MOTORHOME, ETC.) NOTE: The transfer case must be shifted into N (Neu- tral) for recreational towing. CAUTION! Shifting Into Neutral (N) Front or rear wheel lifts should not be used. Internal Use the following procedure to prepare your vehicle for damage to the transmission or transfer case will occur recreational towing.
Page 347: Shifting Out Of Neutral (N)
STARTING AND OPERATING 347 4. Start engine. CAUTION! 5. Shift automatic transmission into D (Drive) or manual Damage to the transmission may occur if the trans- transmission into gear. mission is shifted into P (Park) with the transfer case 6. Release brake pedal and ensure that there is no vehicle in N (Neutral) and the engine running.
Page 348 348 STARTING AND OPERATING 3. Shift automatic transmission into D (Drive) or release CAUTION! clutch on manual transmissions. • Do not use a bumper mounted clamp-on tow bar NOTE: When shifting out of transfer case N (Neutral) on your vehicle. The bumper face bar will be on automatic transmission equipped vehicles, turning damaged.
Page 349: What To Do In Emergencies
WHAT TO DO IN EMERGENCIES CONTENTS ▫ Preparations For Jacking ....353 Hazard Warning Flashers ....350 ▫...
Page 350: Hazard Warning Flashers
350 WHAT TO DO IN EMERGENCIES HAZARD WARNING FLASHERS Your vehicle’s hazard warning flasher is an emergency warning system. When you activate it, all front and rear directional signals will flash intermittently. Use it when your vehicle is disabled on or near the road. It warns other drivers to steer clear of you and your vehicle.
Page 351: If Your Engine Overheats
WHAT TO DO IN EMERGENCIES 351 IF YOUR ENGINE OVERHEATS CAUTION! In any of the following situations, you can reduce the potential for overheating by taking the appropriate ac- Driving with a hot cooling system could damage tion. your vehicle. If the temperature gauge reads “H”, •...
Page 352: Jacking And Tire Changing
352 WHAT TO DO IN EMERGENCIES JACKING AND TIRE CHANGING Jack Location The jack and lug wrench are located in the rear storage WARNING! compartment. Refer to “Storage” in Section 3 of this manual. • Getting under a jacked-up vehicle is dangerous. The vehicle could slip off the jack and fall on you.
Page 353: Spare Tire Stowage
WHAT TO DO IN EMERGENCIES 353 Spare Tire Stowage WARNING! To remove the spare tire from the carrier, remove the tire cover, if equipped, and remove the lug nuts with the lug Do not attempt to change a tire on the side of the wrench turning them counterclockwise.
Page 354: Jacking Instructions
354 WHAT TO DO IN EMERGENCIES Jacking Instructions 1. Remove spare tire, jack and tools from stored location. 2. Loosen (but do not remove) the wheel lug nuts by turning them to the left one turn while the wheel is still on the ground.
Page 355 WHAT TO DO IN EMERGENCIES 355 nuts until each nut has been tightened twice. Correct WARNING! wheel nut tightness is 130 N·m (95 ft. lbs). If in doubt about the correct tightness, have them checked with a Raising the vehicle higher than necessary can make torque wrench by your authorized dealer or at a service the vehicle less stable and cause an accident.
Page 356: Jump Starting
356 WHAT TO DO IN EMERGENCIES 1. Remove all metal jewelry such as watch bands or JUMP STARTING If the vehicle has a discharged battery, booster cables may bracelets which might make an unintended electrical be used to obtain a start from a booster battery or the contact.
Page 357 WHAT TO DO IN EMERGENCIES 357 WARNING! WARNING! • You should not try to start your vehicle by pushing Do not permit vehicles to touch each other as this could establish a ground connection and personal or towing. injury could result. •...
Page 358: Emergency Tow Hooks - If Equipped
358 WHAT TO DO IN EMERGENCIES 6. Start the engine in the vehicle which has the booster EMERGENCY TOW HOOKS — IF EQUIPPED battery, let the engine idle a few minutes, then start the If your vehicle is equipped with tow hooks, they are engine in the vehicle with the discharged battery.
Page 359: Towing A Disabled Vehicle
WHAT TO DO IN EMERGENCIES 359 TOWING A DISABLED VEHICLE WARNING! The manufacturer recommends towing with all four wheels OFF the ground. Acceptable methods are to tow Stand clear of vehicles when pulling with tow hooks. the vehicle on a flatbed or with one end of the vehicle Tow straps and chains may break, causing serious raised and the other end on a towing dolly.
Page 360 I n f o r ma t i o n P r o v i d e d b y :...
Page 361: Maintaining Your Vehicle
MAINTAINING YOUR VEHICLE CONTENTS ▫ Drive Belts — Check Condition And Tension . . 372 Engine Compartment – 3.8L ....364 ▫ Spark Plugs ......373 Onboard Diagnostic System —...
Page 362 362 MAINTAINING YOUR VEHICLE ▫ Driveline And Steering Component ▫ Front/Rear Axle Fluid ....392 Lubrication ......378 ▫...
Page 363 MAINTAINING YOUR VEHICLE 363 ▫ Engine ......413 Fluid Capacities ......412 ▫...
Page 364: Engine Compartment - 3.8L
364 MAINTAINING YOUR VEHICLE ENGINE COMPARTMENT – 3.8L I n f o r ma t i o n P r o v i d e d b y :...
Page 365: Onboard Diagnostic System - Obd Ii
MAINTAINING YOUR VEHICLE 365 ONBOARD DIAGNOSTIC SYSTEM — OBD II CAUTION! Your vehicle is equipped with a sophisticated onboard diagnostic system called OBD II. This system monitors • Prolonged driving with the “Malfunction Indica- the performance of the emissions, engine, and automatic tor Light”...
Page 366: Loose Fuel Filler Cap Message
366 MAINTAINING YOUR VEHICLE Loose Fuel Filler Cap Message EMISSIONS INSPECTION AND MAINTENANCE After fuel is added, the vehicle diagnostic system can PROGRAMS determine if the fuel filler cap is possibly loose, improp- In some localities, it may be a legal requirement to pass erly installed, or damaged.
Page 367 MAINTAINING YOUR VEHICLE 367 Your vehicle has a simple ignition key actuated test, ignition key or start the engine. This means that your which you can use prior to going to the test station. To vehicle’s OBD system is not ready and you should not check if your vehicle’s OBD system is ready, you must do proceed to the I/M station.
Page 368: Replacement Parts
368 MAINTAINING YOUR VEHICLE vehicle serviced before going to the I/M station. The I/M NOTE: Intentional tampering with emissions control station can fail your vehicle because the MIL symbol is on systems can result in civil penalties being assessed with the engine running. against you.
Page 369: Maintenance Procedures
MAINTAINING YOUR VEHICLE 369 Checking the oil while the vehicle is on level ground will MAINTENANCE PROCEDURES The pages that follow contain the required maintenance improve the accuracy of the oil level readings. Always services determined by the engineers who designed your maintain the oil level within the SAFE zone on the vehicle.
Page 370 370 MAINTAINING YOUR VEHICLE • More than 50% of your driving is at sustained high CAUTION! speeds during hot weather, above 90°F (32°C) • Taxi, Police, or delivery service (commercial service) Overfilling or underfilling the crankcase will cause aeration or loss of oil pressure. This could damage •...
Page 371 MAINTAINING YOUR VEHICLE 371 Engine Oil Selection Engine Oil Viscosity (3.8L Engines) For best performance and maximum protection for all SAE 5W-20 engine oil is recommended for all operating engines under all types of operating conditions, the temperatures. This engine oil improves low tempera- manufacturer recommends engine oils that are API Cer- ture starting and vehicle fuel economy.
Page 372: Drive Belts - Check Condition And Tension
372 MAINTAINING YOUR VEHICLE present a problem to the environment. Contact your Drive Belts — Check Condition and Tension authorized dealer, service station, or governmental Belt tension is controlled by means of an automatic agency for advice on how and where used oil can be tensioner.
Page 373: Spark Plugs
MAINTAINING YOUR VEHICLE 373 Spark Plugs CAUTION! Spark plugs must fire properly to assure engine perfor- mance and emission control. New plugs should be in- Damage to the catalytic converter can result if your stalled at the mileage specified in the appropriate main- vehicle is not kept in proper operating condition.
Page 374 374 MAINTAINING YOUR VEHICLE • Do not shut off the engine or interrupt the ignition WARNING! when the transmission is in gear and the vehicle is in motion. A hot exhaust system can start a fire if you park over materials that can burn.
Page 375: Crankcase Emission Control System
MAINTAINING YOUR VEHICLE 375 Crankcase Emission Control System Engine Air Cleaner Filter Proper operation of this system depends on freedom Under normal driving conditions, replace the air filter at from sticking or plugging due to deposits. As vehicle the intervals shown on “Maintenance Schedule A.” If, mileage builds up, the PCV valve and passages may however, you drive the vehicle frequently under dusty or accumulate deposits.
Page 376: Maintenance-Free Battery
376 MAINTAINING YOUR VEHICLE Maintenance-Free Battery CAUTION! Your vehicle is equipped with a maintenance-free battery. You will never have to add water, nor is periodic main- It is essential when replacing the cables on the tenance required. battery that the positive cable is attached to the positive post and the negative cable is attached to the WARNING! negative post.
Page 377: Power Steering Fluid Check
MAINTAINING YOUR VEHICLE 377 include cleaning of the condenser fins and a performance test. Drive belt tension should also be checked at this Refrigerant Recovery and Recycling time. R-134a Air Conditioning Refrigerant is a hydrofluorocar- bon (HFC) that is endorsed by the Environmental Pro- WARNING! tection Agency and is an ozone-saving product.
Page 378: Driveline And Steering Component Lubrication
378 MAINTAINING YOUR VEHICLE Driveline And Steering Component Lubrication WARNING! All driveline and steering components are sealed and do not require lubrication. Driveshafts are not serviceable. Fluid level should be checked on a level surface with the engine off to prevent injury from moving parts, Body Lubrication and to insure accurate fluid level reading.
Page 379: Windshield Wiper Blades
MAINTAINING YOUR VEHICLE 379 amount of a high quality lubricant such as Mopar Lock Windshield Washers Cylinder Lubricant directly into the lock cylinder. The fluid reservoir in the engine compartment should be checked for fluid level at regular intervals. Fill the Windshield Wiper Blades reservoir with windshield antifreeze (not radiator anti- Clean the rubber edges of the wiper blades and the...
Page 380: Exhaust System
380 MAINTAINING YOUR VEHICLE Exhaust System Cooling System The best protection against carbon monoxide entry into WARNING! the vehicle body is a properly maintained engine exhaust system. You or others can be badly burned by hot antifreeze/ If you notice a change in the sound of the exhaust system; coolant or steam from your radiator.
Page 381 MAINTAINING YOUR VEHICLE 381 garden hose vertically down the face of the A/C con- Cooling System — Drain, Flush, And Refill denser (if equipped) or the back of the radiator core. At the intervals shown in the appropriate “Maintenance Schedule,” the system should be drained, flushed, and Check the engine cooling system hoses for brittle rubber, refilled.
Page 382 382 MAINTAINING YOUR VEHICLE Adding Engine Coolant CAUTION! Your vehicle has been built with an improved antifreeze/ coolant that allows extended maintenance intervals. This • Mixing of antifreeze/coolant other than the speci- antifreeze/coolant can be used up to 5 Years or 100,000 fied HOAT antifreeze/coolant may result in de- miles before replacement.
Page 383 MAINTAINING YOUR VEHICLE 383 Use only high purity water such as distilled or deionized The cap should be inspected and cleaned if there is any water when mixing the water/antifreeze (coolant) solu- accumulation of foreign material on the sealing surfaces. tion.
Page 384 384 MAINTAINING YOUR VEHICLE children, do not store ethylene glycol based antifreeze/ When additional antifreeze/coolant is needed to main- coolant in open containers or allow it to remain in tain the proper level, it should be added to the coolant puddles on the ground.
Page 385: Hoses And Vacuum/Vapor Harnesses
MAINTAINING YOUR VEHICLE 385 coolant needs to be added, contents of coolant recov- ONLY the correct type thermostat. Other designs may ery bottle must also be protected against freezing. result in unsatisfactory cooling performance, poor gas mileage, and increased emissions. •...
Page 386: Brake System
386 MAINTAINING YOUR VEHICLE are present. Components should be replaced immedi- Brake and Power Steering System Hoses ately if there is any evidence of degradation that could When servicing the vehicle for scheduled maintenance, cause failure. inspect surface of hoses for evidence of heat and me- chanical damage.
Page 387 MAINTAINING YOUR VEHICLE 387 should be checked when pads are replaced. However, WARNING! low fluid level may be caused by a leak and a checkup may be needed. Worn brake hoses can burst and cause brake failure. You could have an accident. If you see any signs of Use only manufacturer’s recommended brake fluid, refer cracking, scuffing, or worn spots, have the brake to Fluids, Lubricants, and Genuine Parts for correct fluid...
Page 388: Automatic Transmission
388 MAINTAINING YOUR VEHICLE Use only brake fluid that has been in a tightly closed CAUTION! container to avoid contamination from foreign matter. Do not allow petroleum base fluid to contaminate the brake Using a transmission fluid other than the manufac- fluid as seal damage will result.
Page 389 MAINTAINING YOUR VEHICLE 389 Check the fluid level while the transmission is at normal 6. Remove the dipstick again and note the fluid level on operating temperature 180° F (82° C). This occurs after at both sides. The fluid level should be between the HOT least 15 mi (25 km) of driving.
Page 390: Hydraulic Clutch Fluid - Manual Transmission
390 MAINTAINING YOUR VEHICLE Special Additives CAUTION! The manufacturer strongly recommends against the ad- dition of any additives to the transmission. The only Be aware that if the fluid temperature is below 50° F exception to this policy is the use of special dyes to aid in (10°...
Page 391: Transfer Case
MAINTAINING YOUR VEHICLE 391 Fluid Level Check Transfer Case Check the fluid level by removing the fill plug. The fluid Fluid Level Check level should be between the bottom of the fill hole and a The fluid level should be to the bottom edge of the fill point not more than 3/16”...
Page 392: Front/Rear Axle Fluid
392 MAINTAINING YOUR VEHICLE Adding Fluid Front/Rear Axle Fluid Fluid should be added only at filler hole until fluid Fluid Level Check begins to run out of the hole. Lubricant should be at bottom edge of the oil fill hole. Drain Adding Fluid First remove fill plug (B), then drain plug (C).
Page 393: Appearance Care And Protection From Corrosion
MAINTAINING YOUR VEHICLE 393 Following off-road usage, completely inspect the under- CAUTION! body of your vehicle. Check tires, body structure, steer- ing, suspension and exhaust system for damage. Check Under frequent heavy-duty driving conditions, threaded fasteners for looseness, particularly on the change all lubricants, and lubricate body compo- chassis, drivetrain components, steering and suspension.
Page 394 394 MAINTAINING YOUR VEHICLE • Bird droppings. hot or cold weather and other extreme conditions will have an adverse effect on paint, metal trim, and under- Washing body protection. • Wash your vehicle regularly. Always wash your ve- The following maintenance recommendations will enable hicle in the shade using Mopar Car Wash or a mild you to obtain maximum benefit from the corrosion car wash soap, and rinse the panels completely with...
Page 395 MAINTAINING YOUR VEHICLE 395 • If your vehicle is damaged due to an accident or CAUTION! similar cause which destroys the paint and protective coating have your vehicle repaired as soon as possible. Do not use abrasive or strong cleaning materials such The cost of such repairs is considered the responsibil- as steel wool or scouring powder, which will scratch ity of the owner.
Page 396 396 MAINTAINING YOUR VEHICLE • For tough stains, apply Mopar Total Clean or a mild Wheel and Wheel Trim Care All wheels and wheel trim, especially aluminum and soap solution to a clean, damp cloth and remove stain. chrome plated wheels should be cleaned regularly with a Use a fresh, damp towel to remove soap residue.
Page 397 MAINTAINING YOUR VEHICLE 397 Cleaning Plastic Instrument Cluster Lenses WARNING! The lenses in front of the instruments in this vehicle are molded in clear plastic. When cleaning the lenses, care Do not use volatile solvents for cleaning purposes. must be taken to avoid scratching the plastic. Many are potentially flammable, and if used in closed areas they may cause respiratory harm.
Page 398 398 MAINTAINING YOUR VEHICLE • After cleaning your vehicle’s fabric top, always make Replace the belts if they appear frayed or worn or if the buckles do not work properly. sure it is completely dry before lowering. • Be especially careful when washing the windows by Appearance Care For Fabric Top Models following the directions for “Care of Fabric Top Win- CAUTION!
Page 399 Use Mopar not up and down. Mopar Jeep Soft Glass Window Soft Top Zipper Cleaner and Lubricant to ease zipper Cleaner will safely clean all plastic windows without operation.
Page 400: Fuses (Totally Integrated Power Module)
400 MAINTAINING YOUR VEHICLE into the zipper teeth. If a stuck zipper slide is experi- enced, work the Mopar Soft Top Zipper Cleaner and Lubricant into the zipper slide. Several applications may be required before the zipper comes free. 6. Never paste stickers, gummed labels or any tape to the windows.
Page 401 MAINTAINING YOUR VEHICLE 401 Cavity Cartridge Mini Description Cavity Cartridge Mini Description Fuse Fuse Fuse Fuse 40 Amp Power Folding Seat 40 Amp PZEV Motor/Flex Green Green Fuel 30 Amp Transfer Case/Pwr 30 Amp Headlamp Wash Pink Liftgate Module Pink Relay/Manual Tuning Valve 40 Amp...
Page 402 402 MAINTAINING YOUR VEHICLE Cavity Cartridge Mini Description Cavity Cartridge Mini Description Fuse Fuse Fuse Fuse 20 Amp Powertrain Control 20 Amp Frt/Rear Axle Lockers Yellow Module (PCM) Trans Yellow Range 10 Amp Trailer Tow 60 Amp Radiator Fan Yellow 25 Amp Inverter 30 Amp...
Page 403 MAINTAINING YOUR VEHICLE 403 Cavity Cartridge Mini Description Cavity Cartridge Mini Description Fuse Fuse Fuse Fuse 20 Amp Ignition Off Draw — 30 Amp Amplifier (AMP) Yellow Vehicle Entertainment Green System (IOD-VES), 20 Amp Ignition Off Draw— Satellite Digital Audio Yellow Cabin Compartment Receiver (SDARS),...
Page 404 404 MAINTAINING YOUR VEHICLE Cavity Cartridge Mini Description Cavity Cartridge Mini Description Fuse Fuse Fuse Fuse 20 Amp COL MOD, IR SNS, 10 Amp Occupant Restraint Yellow Heater Ventilation, Controller/Occupant Classification Module Air Conditioning/ (ORC/OCM) Automatic Tempera- ture Control (HVAC/ 15 Amp Left Tail/License/ ATC), Rear View...
Page 405 MAINTAINING YOUR VEHICLE 405 Cavity Cartridge Mini Description Cavity Cartridge Mini Description Fuse Fuse Fuse Fuse 20 Amp Auto Shut Down 10 Amp Ignition Switch (IGN Yellow (ASD #3) SW), Window Module (WIN MOD) 10 Amp Right Horn (RT HORN (HI/LOW) 10 Amp Next Generation Con- troller (NGC), Trans-...
Page 406 406 MAINTAINING YOUR VEHICLE Cavity Cartridge Mini Description Cavity Cartridge Mini Description Fuse Fuse Fuse Fuse 10 Amp Occupant Restraint 20 Amp Power Outlet #3 Controller (ORC), TT Yellow (BATT) EUROPE 10 Amp Anti-Lock Brake Sys- 10 Amp Next Generation Con- tem (ABS), Electronic troller (NGC), Global Stability Program...
Page 407: Vehicle Storage
MAINTAINING YOUR VEHICLE 407 VEHICLE STORAGE CAUTION! If you are leaving your vehicle dormant for more than 21 days you may want to take steps to protect your battery. • When installing the Integrated Power Module You may: cover, it is important to ensure the cover is prop- erly positioned and fully latched.
Page 408: Replacement Bulbs - If Equipped
408 MAINTAINING YOUR VEHICLE REPLACEMENT BULBS — IF EQUIPPED Exterior Lights Bulb Type Backup Lights (2)......3157 Center High Mounted Stop Light (1) .
Page 409: Bulb Replacement
MAINTAINING YOUR VEHICLE 409 9. Push connector locking tab to the unlock position. BULB REPLACEMENT Head Light 10. Remove connector from bulb. 1. Open hood and support using prop rod. 11. Push connector onto new bulb base, and push the connector locking tab to the lock position.
Page 410: Front Park/Turn Signal
410 MAINTAINING YOUR VEHICLE Front Park/Turn Signal Front Fog Light 1. Remove the front grille. Turn the retainers along the 1. Locate the front fog lamp in the front fascia, and top 1/4 turn counter-clockwise and remove. disconnect the electrical connector from underneath. 2.
Page 411: Rear Tail, Stop, Turn Signal, And Back-Up Lights
MAINTAINING YOUR VEHICLE 411 3. Rotate the appropriate socket 1/4 turn counter- Rear Tail, Stop, Turn Signal, and Back-Up Lights clockwise, then remove it from the housing. 1. Remove the two (2) inboard screws attaching the tail light housing to the body. DO NOT REMOVE THE 4.
Page 412: Fluid Capacities
412 MAINTAINING YOUR VEHICLE FLUID CAPACITIES U.S. Metric Fuel (Approximate) — 2 Door Models 18.5 Gallons 70 Liters Fuel (Approximate) — 4 Door Models 22.5 Gallons 85 Liters Engine Oil with Filter 3.8 Liter Engine (SAE 5W-20, API Certified Engine Oil) 6 Quarts 5.7 Liters Cooling System *...
Page 413: Engine
MAINTAINING YOUR VEHICLE 413 FLUIDS, LUBRICANTS AND GENUINE PARTS Engine Component Fluid, Lubricant, or Genuine Part Engine Coolant Mopar Antifreeze/Coolant 5 Year/100,000 Mile Formula HOAT (Hybrid Or- ganic Additive Technology) Engine Oil API Certified SAE 5W-20 Engine Oil is recommended. Meets the requirements of DaimlerChrysler Material Standard MS-6395.
Page 414: Chassis
414 MAINTAINING YOUR VEHICLE Chassis Component Fluid, Lubricant, or Genuine Part Automatic Transmission Mopar ATF+4 Automatic Transmission Fluid Manual Transmission Mopar Manual Transmission Lubricant or equivalent (meeting the require- ments of DaimlerChrysler Material Standard MS-9224) Transfer Case Mopar ATF+4 Automatic Transmission Fluid or equivalent. Axle Differential (Front) Mopar Gear &...
Page 415: Maintenance Schedules
MAINTENANCE SCHEDULES CONTENTS ▫ Schedule “B” ......419 Emission Control System Maintenance ..416 ▫...
Page 416 416 MAINTENANCE SCHEDULES EMISSION CONTROL SYSTEM MAINTENANCE MAINTENANCE SCHEDULES The “Scheduled” maintenance services, listed in bold There are two maintenance schedules that show the type must be done at the times or mileages specified to required service for your vehicle. assure the continued proper functioning of the emission First is Schedule B .
Page 417 MAINTENANCE SCHEDULES 417 • Trailer towing NOTE: Most vehicles are operated under the conditions listed for Schedule “B.” • Taxi, police, or delivery service (commercial service) Second is Schedule “A”. It is for vehicles that are not • Off-road or desert driving operated under any of the conditions listed under Sched- NOTE: If ANY of these apply to you then change your ule “B.”...
Page 418 418 MAINTENANCE SCHEDULES • Check all lights and all other electrical items for correct At Each Stop for Fuel operation. • Check the engine oil level about 5 minutes after a fully warmed engine is shut off. Checking the oil level while At Each Oil Change the vehicle is on level ground will improve the accu- •...
Page 419 SCHEDULE “B” 419 • Off-road or desert driving Schedule “B” Follow this schedule if you usually operate your vehicle • If equipped for and operated with E-85 (ethanol) under one or more of the following conditions. fuel. • Day or night temperatures are below 32°F (0°C) NOTE: If ANY of these apply to you then change your •...
Page 420 420 SCHEDULE “B” Miles 3,000 6,000 9,000 12,000 15,000 (Kilometers) (5 000) (10 000) (15 000) (20 000) (25 000) Change the engine oil and engine oil filter, if not replaced at 3 months. Rotate the tires. Inspect the engine air filter element, replace if necessary.
Page 421 SCHEDULE “B” 421 Miles 18,000 21,000 24,000 27,000 30,000 (Kilometers) (30 000) (35 000) (40 000) (45 000) (50 000) Change the engine oil and engine oil filter, if not replaced at 3 months. Rotate the tires. Inspect the engine air filter element, replace if necessary.
Page 422 422 SCHEDULE “B” Miles 33,000 36,000 39,000 42,000 45,000 (Kilometers) (55 000) (60 000) (65 000) (70 000) (75 000) Change the engine oil and engine oil filter, if not replaced at 3 months. Rotate the tires. Inspect the engine air filter element, replace if necessary.
Page 423 SCHEDULE “B” 423 Miles 48,000 51,000 54,000 57,000 60,000 (Kilometers) (80 000) (85 000) (90 000) (95 000) (100 000) Change the engine oil and engine oil filter, if not replaced at 3 months. Rotate the tires. Inspect the engine air filter element, replace if necessary.
Page 424 424 SCHEDULE “B” Miles 48,000 51,000 54,000 57,000 60,000 (Kilometers) (80 000) (85 000) (90 000) (95 000) (100 000) Drain and refill the automatic transmission fluid. Replace main sump filter and spin-on cooler return filter (if equipped).‡ Inspect the drive belt, and replace as needed. Not required if belt was previously.
Page 425 SCHEDULE “B” 425 Miles 63,000 66,000 69,000 72,000 75,000 (Kilometers) (105 000) (110 000) (115 000) (120 000) (125 000) Change the engine oil and engine oil filter, if not replaced at 3 months. Rotate the tires. Inspect the engine air filter element, replace if necessary.
Page 426 426 SCHEDULE “B” Miles 78,000 81,000 84,000 87,000 90,000 (Kilometers) (130 000) (135 000) (140 000) (145 000) (150 000) Change the engine oil and engine oil filter, if not replaced at 3 months. Rotate the tires. Inspect the engine air filter element, replace if necessary.
Page 427 SCHEDULE “B” 427 Miles 93,000 96,000 99,000 102,000 105,000 (Kilometers) (155 000) (160 000) (165 000) (170 000) (175 000) Change the engine oil and engine oil filter, if not replaced at 3 months. Rotate the tires. Inspect the engine air filter element, replace if necessary. Replace the spark plugs.
Page 428 428 SCHEDULE “B” Miles 108,000 111,000 114,000 117,000 120,000 (Kilometers) (180 000) (185 000) (190 000) (195 000) (200 000) Change the engine oil and engine oil filter, if not replaced at 3 months. Rotate the tires. Inspect the engine air filter element, replace if necessary. Inspect the PCV Valve, and replace if necessary.
Page 429 SCHEDULE “B” 429 Miles 123,000 126,000 129,000 132,000 135,000 (Kilometers) (205 000) (210 000) (215 000) (220 000) (225 000) Change the engine oil and engine oil filter, if not replaced at 3 months. Rotate the tires. Inspect the engine air filter element, replace if necessary.
Page 430 430 SCHEDULE “B” Miles 138,000 141,000 144,000 147,000 150,000 (Kilometers) (230 000) (235 000) (240 000) (245 000) (250 000) Change the engine oil and engine oil filter, if not replaced at 3 months. Rotate the tires. Inspect the engine air filter element, replace if necessary. Inspect the PCV Valve, and replace if necessary.
Page 431 SCHEDULE “B” 431 Inspection and service should also be performed anytime ‡Off-highway operation, trailer towing, taxi, limousine, a malfunction is observed or suspected. Retain all re- bus, snow plowing, or other types of commercial service ceipts. or prolonged operation with heavy loading, especially in hot weather, require front and rear axle service indicated †...
Page 432 432 SCHEDULE “A” Schedule “A” Miles 6,000 12,000 18,000 24,000 30,000 (Kilometers) (10 000) (20 000) (30 000) (40 000) (50 000) [Months] [12] [18] [24] [30] Change the engine oil and engine oil filter. Rotate the tires. Inspect the engine air filter element, and replace if necessary.
Page 433 SCHEDULE “A” 433 Miles 36,000 42,000 48,000 54, 000 (Kilometers) (60 000) (70 000) (80 000) (90 000) [Months] [36] [42] [48] [54] Change the engine oil and engine oil filter. Rotate the tires. Inspect the brake linings. Clean and lubricate soft top zippers (if equipped). I n f o r ma t i o n P r o v i d e d b y :...
Page 434 434 SCHEDULE “A” Miles 60,000 66,000 72,000 78,000 (Kilometers) (100 000) (110 000) (120 000) (130 000) [Months] [60] [66] [72] [78] Change the engine oil and engine oil filter. Rotate the tires. Inspect the engine air filter element, and replace if nec- essary.
Page 435 SCHEDULE “A” 435 Miles 84,000 90,000 96,000 102, 000 (Kilometers) (140 000) (150 000) (160 000) (170 000) [Months] [84] [90] [96] [102] Change the engine oil and engine oil filter. Rotate the tires. Inspect the engine air filter element, and replace if necessary. Inspect the PCV Valve, and replace if necessary.
Page 436 436 SCHEDULE “A” Miles 108,000 114,000 120,000 126,000 (Kilometers) (180 000) (190 000) (200 000) (210 000) [Months] [108] [114] [120] [126] Change the engine oil and engine oil filter. Rotate the tires. Inspect the engine air filter element, and replace if nec- essary.
Page 437 SCHEDULE “A” 437 Miles 132,000 138,000 144,000 150,000 (Kilometers) (220 000) (230 000) (240 000) (250 000) [Months] [132] [138] [144] [150] Change the engine oil and engine oil filter. Rotate the tires. Inspect the engine air filter element, and replace if nec- essary.
Page 438 438 SCHEDULE “A” Inspection and service should also be performed anytime This maintenance is recommended by the manufac- a malfunction is observed or suspected. Retain all re- turer to the owner, but is not required to maintain ceipts. emissions warranty. I n f o r ma t i o n P r o v i d e d b y :...
Page 439: If You Need Consumer Assistance
IF YOU NEED CONSUMER ASSISTANCE CONTENTS Suggestions For Obtaining Service For Your Reporting Safety Defects ....443 Vehicle ......440 ▫...
Page 440: Suggestions For Obtaining Service For Your Vehicle
Warranty service must be done by an authorized or work done that is not on your maintenance log, let the Chrysler, Dodge, or Jeep dealer. We strongly recommend service advisor know. that you take your vehicle to your selling dealer. They know you and your vehicle best, and are most concerned that you get prompt and high quality service.
Page 441 IF YOU NEED CONSUMER ASSISTANCE 441 • Vehicle identification number technicians, special tools, and the latest information to assure your vehicle is fixed correctly and in a timely • Vehicle delivery date and mileage manner. DaimlerChrysler Motors Corporation Customer Center This is why you should always talk to your dealer’s P.O.
Page 442 442 IF YOU NEED CONSUMER ASSISTANCE Customer Assistance For The Hearing Or Speech contract, call the manufacturer’s Service Contract Na- Impaired (TDD/TTY) tional Customer Hotline at 1-800-521-9922. To assist customers who have hearing difficulties, the The manufacturer will not stand behind any service manufacturer has installed special TDD (Telecommuni- contract that is not the manufacturer’s Service Contract.
Page 443: Warranty Information (U.s. Vehicles Only)
IF YOU NEED CONSUMER ASSISTANCE 443 MOPAR PARTS WARNING! Mopar fluids, lubricants, parts, and accessories are available from your dealer. They will help you keep your Engine exhaust, some of its constituents, and certain vehicle operating at its best. vehicle components contain or emit chemicals known to the State of California to cause cancer and REPORTING SAFETY DEFECTS birth defects or other reproductive harm.
Page 444: In Canada
444 IF YOU NEED CONSUMER ASSISTANCE To contact NHTSA, you may either call the Auto Safety PUBLICATION ORDER FORMS Hotline toll free at 1–888–327–4236 (TTY: 1–800–424– To order the following manuals, you may use either the 9153), or go to http://www.safercar.gov; or write to: website or the phone numbers listed below.
Page 445 IF YOU NEED CONSUMER ASSISTANCE 445 • Diagnostic Procedure Manuals. Call Toll Free at: • 1–800–890–4038 (U.S.) Filled with diagrams, charts and detailed illustrations, these practical manuals make it easy for students and • 1–800–387–1143 (Canada) technicians to find and fix problems on computer- controlled vehicle systems and features.
Page 446: Department Of Transportation Uniform Tire
446 IF YOU NEED CONSUMER ASSISTANCE may depart significantly from the norm due to variations DEPARTMENT OF TRANSPORTATION UNIFORM TIRE QUALITY GRADES in driving habits, service practices and differences in road The following describes the tire grading categories estab- characteristics and climate. lished by the National highway Traffic Safety Adminis- Traction Grades tration.
Page 447: Temperature Grades
IF YOU NEED CONSUMER ASSISTANCE 447 Temperature Grades WARNING! The temperature grades are A (the highest), B, and C, representing the tire’s resistance to the generation of heat The temperature grade for this tire is established for and its ability to dissipate heat when tested under a tire that is properly inflated and not overloaded.
Page 448 I n f o r ma t i o n P r o v i d e d b y :...
Page 449 INDEX I n f o r ma t i o n P r o v i d e d b y :...
Page 450 450 INDEX ABS (Anti-Lock Brake System) ... . 204,296 Alterations/Modifications, Vehicle ... . . 9 Adding Fuel ......325 Antenna, Satellite Radio .
Page 451 INDEX 451 Battery ....... 376 Capacities, Fluid ......412 Emergency Starting .
Page 452 452 INDEX Check Engine Light Drain, Flush, and Refill ....381 (Malfunction Indicator Light) ... . . 208,366 Inspection .
Page 453 INDEX 453 Dimmer Switch, Headlight ....100 Electronic Brake Control System ... . . 107 Dipsticks Anti-Lock Brake System .
Page 454 454 INDEX Emission Control System Maintenance ..366,416 Engine Oil Viscosity ..... . 371 Engine Engine Oil Viscosity Chart .
Page 455 INDEX 455 Turn Signal ..... 203,410,411 Fuel ....... . . 321 Flooded Engine Starting .
Page 456 456 INDEX Odometer ......208 Replacing ......409 Speedometer .
Page 457 INDEX 457 Instrument Cluster ..... . . 201 Keys ....... . . 14 Instrument Panel and Controls .
Page 458 458 INDEX Cruise ......205 Passing ......100 Daytime Running .
Page 459 INDEX 459 Lower Anchors and Tether for CHildren Outside ......86 (LATCH) .
Page 460 460 INDEX Oil, Engine ......369 Passing Light ......100 Capacity .
Page 461 INDEX 461 Radio, Navigation ..... . . 245 Remote Control Radio Operation ......252 Door Locks .
Page 462 462 INDEX Satellite Radio Antenna ....248 Rear Folding ......93 Schedule, Maintenance .
Page 463 INDEX 463 Shoulder Belt Upper Anchorage ....43 Steering Shoulder Belts ......37 Power .
Page 464 464 INDEX Theft System Disarming ....19 Quality Grading ..... . . 446 Tilt Steering Column .
Page 465 INDEX 465 Traction Control ......108 Transmitter Battery Service Traction Control Light ....208 (Remote Keyless Entry) .
Page 466 466 INDEX Viscosity, Engine Oil ..... . 371 Wheel Mounting ......355 Wind Buffeting .
Page 467 INTRODUCTION INTRODUCTION Roll Over WarningHOW TO USE THIS MANUAL WARNINGS AND CAUTIONS VEHICLE IDENTIFICATION NUMBER VEHICLE MODIFICATIONS/ALTERATIONS THINGS TO KNOW BEFORE STARTING YOUR VEHICLE A WORD ABOUT YOUR KEYS Ignition Key RemovalKey-In-Ignition ReminderSTEERING WHEEL LOCK - IF EQUIPPED To Manually Lock the Steering WheelTo Release the Steering Wheel LockSENTRY KEY IMMOBILIZER SYSTEM Important Note About ServiceReplacement KeysCustomer Key ProgrammingGeneral InformationSECURITY ALARM SYSTEM - IF EQUIPPED To Set the AlarmTo Disarm the SystemILLUMINATED ENTRY REMOTE KEYLESS ENTRY - IF EQUIPPED To Unlock the Doors and Swing GateTo Lock the Doors and Swing GateUsing The Panic AlarmTo Turn Off Flash Lights With LockProgramming Additional TransmittersGeneral InformationBattery ReplacementDOORS Front Door RemovalRear Door Removal (4 Door Models)DOOR LOCKS Manual Door LocksPower Door Locks - If EquippedWINDOWS Power Windows - If EquippedWind BuffetingREAR SWING GATE OCCUPANT RESTRAINTS Lap/Shoulder BeltsRear Center Lap/Shoulder Belt Retractor Lock-OutAdjustable Upper Shoulder Belt AnchorageSeat Belt PretensionersEnhanced Seat...

Jeep 2007 wrangler Owner's Manual

Introduction 1

Things to Know before Starting Your Vehicle

Understanding the Features of Your Vehicle

Understanding Your Instrument Panel

Starting and Operating

What to Do in Emergencies

Maintaining Your Vehicle

Quick Links

INTRODUCTION

Chapters

Related Manuals for Jeep 2007 wrangler

Summary of Contents for Jeep 2007 wrangler