Roland SK-50 Owner's Manual page 50

REVERB MACRO is a parameter used to select the preset type of the effect.
When set to another REVERB MACRO, all other reverb parameters will reset to the values set for each type of REVERB MACRO.
40 01 38 00 00 01 00 - 07
40 01 39 00 00 01 00 - 07
40 01 3A 00 00 01 00 - 7F
40 01 3B 00 00 01 00 - 7F
40 01 3C 00 00 01 00 - 7F
40 01 3D 00 00 01 00 - 7F
40 01 3E 00 00 01 00 - 7F
40 01 3F 00 00 01 00 - 7F
CHORUS MACRO is a parameter used to select the preset type of effect.
When set to another CHORUS MACRO, then all other chorus parameters will reset to the values set for each type of CHORUS MACRO.
40 1x 00 00 00 02 00 - 7F
40 1x 01# 00 - 7F
40 1x 02 00 00 01 00 - 10
40 1x 03 00 00 01 00 - 01
40 1x 04 00 00 01 00 - 01
40 1x 05 00 00 01 00 - 01
40 1x 06 00 00 01 00 - 01
40 1x 07 00 00 01 00 - 01
40 1x 08 00 00 01 00 - 01
40 1x 09 00 00 01 00 - 01
40 1x 0A 00 00 01 00 - 01
* Rx. NRPN is set to OFF by power-on reset or by "General MIDI mode On", and it is set to ON by "GS RESET" .
40 1x 0B 00 00 01 00 - 01
40 1x 0C 00 00 01 00 - 01
40 1x 0D 00 00 01 00 - 01
40 1x 0E 00 00 01 00 - 01
40 1x 0F 00 00 01 00 - 01
40 1x 10 00 00 01 00 - 01
40 1x 11 00 00 01 00 - 01
40 1x 12 00 00 01 00 - 01
40 1x 13 00 00 01 00 - 01
40 1x 14 00 00 01 00 - 02
ASSIGN MODE is a parameter used to select the voice assign manner when "multiple Note Ons" occur(the same note number on the same channel at
the same time).
The best assign modes ( SINGLE(0) for Drum part and LIMITED-MULTI(1) for the other parts ) are selected automatically, so you need not reset this
parameter.
40 1x 15 00 00 01 00 - 02
USE FOR RHYTHM PART is a parameter to define the part to be used as an ordinary part (0), as a drum part using DRUM MAP1(1), or a drum part
using DRUM MAP2(2). The default is MAP1(1) for Part10 (MIDI CH=10, x=0), and all other parts are set to ordinary parts (OFF(0)).
40 1x 16 00 00 01 28 - 58
40 1x 17 00 00 02 08 - F8
40 1x 18#
40 1x 19 00 00 01 00 - 7F
40 1x 1A 00 00 01 00 - 7F
40 1x 1B 00 00 01 00 - 7F
40 1x 1C 00 00 01 00 - 7F
40 1x 1D 00 00 01 00 - 7F
40 1x 1E 00 00 01 00 - 7F
40 1x 1F 00 00 01 00 - 5F
40 1x 20 00 00 01 00 - 5F
CHORUS MACRO 00: Chorus 1
01: Chorus 2
02: Chorus 3
03: Chorus 4
04: Feedback Chorus
05: Flanger
06: Short Delay
07: Short Delay(FB)
CHORUS PRE-LPF 0-7
CHORUS LEVEL 0-127
CHORUS FEEDBACK 0-127
CHORUS DELAY 0-127
CHORUS RATE 0-127
CHORUS DEPTH 0-127
CHORUS SEND LEVEL TO REVERB 0-127
TONE NUMBER CC#00 VALUE (0-127)
P.C. VALUE (1-128)
Rx. CHANNEL 1 - 16,OFF
Rx. PITCH BEND OFF / ON
Rx. CH PRESSURE(CAf) OFF / ON
Rx. PROGRAM CHANGE OFF / ON
Rx. CONTROL CHANGE OFF / ON
Rx. POLY PRESSURE(PAf) OFF / ON
Rx. NOTE MESSAGE OFF / ON
Rx. RPN OFF / ON
Rx. NRPN OFF / ON
Rx. MODULATION OFF / ON
Rx. VOLUME OFF / ON
Rx. PANPOT OFF / ON
Rx. EXPRESSION OFF / ON
Rx. HOLD1 OFF / ON
Rx. PORTAMENTO OFF / ON
Rx. SOSTENUTO OFF / ON
Rx. SOFT OFF / ON
MONO/POLY MODE Mono / Poly
(=Bn 7E 01 / Bn 7F 00)
ASSIGN MODE 0 = SINGLE
1 =LIMITED-MULTI
2 = FULL-MULTI
USE FOR RHYTHM PART 0 = OFF
1 = MAP1
2 = MAP2
PITCH KEY SHIFT -24 - +24
[semitones]
PITCH OFFSET FINE -12.0 - +12.0 [Hz]
Use nibblized data.
PART LEVEL 0 - 127
(=Bn 07 vv)
VELOCITY SENSE DEPTH 0 - 127
VELOCITY SENSE OFFSET 0 - 127
PART PANPOT Random,
-63(LEFT) - +63(RIGHT)
(=Bn 0A vv, except random)
KEY RANGE LOW C-1 - G9
KEY RANGE HIGH C-1 - G9
CC1 CONTROLLER NUMBER 0 - 95
CC2 CONTROLLER NUMBER 0 - 95
02 Chorus 3
00 0
40 64
08 8
50 80
03 3
13 19
00 0
00 0
00 1
Same as the Part#
01 ON
01 ON
01 ON
01 ON
01 ON
01 ON
01 ON
00 (01*) OFF (ON*)
01 ON
01 ON
01 ON
01 ON
01 ON
01 ON
01 ON
01 ON
01 Poly
00 at x=0 SINGLE
01 at x≠0 LIMITED-MULTI
00 at x≠0 OFF
01 at x=0 MAP1
40 0 [semitones]
08 00 0 [Hz]
64 100
40 64
40 64
40 0 (center)
00 C-1
7F G9
10 16
11 17
49