Roland SK-50 Owner's Manual page 43

NRPN Data entry Description
MSB LSB MSB
=========================================================
01H 08H mmH Vibrato rate
relative change on specified channel
mm: 0EH - 40H - 72H (-50 - 0 - +50)
01H 09H mmH Vibrato depth
relative change on specified channel
mm: 0EH - 40H - 72H (-50 - 0 - +50)
01H 0AH mmH Vibrato delay
relative change on specified channel
mm: 0EH - 40H - 72H (-50 - 0 - +50)
01H 20H mmH TVF cutoff frequency
relative change on specified channel
mm: 0EH - 40H - 72H (-50 - 0 - +50)
01H 21H mmH TVF resonance
relative change on specified channel
mm: 0EH - 40H - 72H (-50 - 0 - +50)
01H 63H mmH TVF&TVA Env. Attack time
relative change on specified channel
mm: 0EH - 40H - 72H (-50 - 0 - +50)
01H 64H mmH TVF&TVA Env. Decay time
relative change on specified channel
mm: 0EH - 40H - 72H (-50 - 0 - +50)
01H 66H mmH TVF&TVA Env. Release time
relative change on specified channel
mm: 0EH - 40H - 72H (-50 - 0 - +50)
18H rrH mmH Pitch coarse of drum instrument
relative change on specified drum instrument
rr: key number of drum instrument
mm: 00H - 40H - 7FH (-64 - 0 - +63 semitone)
1AH rrH mmH TVA level of drum instrument
absolute change on specified drum instrument
rr: key number of drum instrument
mm: 00H - 7FH (zero - maximum)
1CH rrH mmH Panpot of drum instrument
absolute change on specified drum instrument
rr: key number of drum instrument
mm: 00H, 01H - 40H - 7FH
(Random, Left-Center-Right)
1DH rrH mmH Reverb send level of drum instrument
absolute change on specified drum instrument
rr: key number of drum instrument
mm: 00H - 7FH (zero - maximum)
1EH rrH mmH Chorus send level of drum instrument
absolute change on specified drum instrument
rr: key number of drum instrument
mm: 00H - 7FH (zero - maximum)
* Data entry LSB is ignored.
* The relative change means that the parameter value(e.g.-50 - 0 - +50) will be
added to the preset value.
* The absolute change means that the parameter value will be replaced by the
received value.
- RPN MSB/LSB
Status Second Third
BnH 65H mmH
BnH 64H llH
n=MIDI channel number :0H - FH (ch.1 - ch.16)
mm=MSB of the RPN
ll=MSB of the RPN
* Ignored when "Rx.RPN = OFF".
* The values set by an RPN won't be reset by receiving new Program Change
messages or Reset All Controllers.
42
**RPN**
An RPN (Registered Parameter Number) is an expanded control change
message.
Each function of an RPN is described by the MIDI Standard.
To use RPN, set RPN number (MSB/LSB) before sending data. Then send data by
Data entry message(Control Change # 6/38). And then, it is recommended to
send RPN null (RPN number = 7FH/7FH) to prevent the data from being
unexpectedly change. For more explanation, refer to section 4. Useful
Information, Example of actual MIDI messages <EXAMPLE 4>.
You can change the following parameters by using RPN.
RPN Data entry Description
MSB LSB MSB LSB
=========================================================
00H 00H mmH --- Pitch bend sensitivity
mm: 00H - 18H (0 - 24 semitone)
Default value = 02H (two semitones)
ll: ignored (value=00H)
(Up to 2 octaves)
00H 01H mmH llH Master fine tuning
mm,ll: 00 00H - 40 00H - 7F 7FH
(-8192 x 100/8192 - 0 - +8191 x 100/8192 cents)
00H 02H mmH --- Master coarse tuning
mm: 28H - 40H - 58H (-24 - 0 - +24 semitones)
ll: ignored (value=00H)
7FH 7FH --- --- RPN null
Return to disable condition.
The parameter already set retains its value.
mm,ll: ignored
•Program change
Status Second
CnH ppH
n=MIDI channel number :0H - FH (ch.1 - ch.16)
pp=Program number :00H - 7FH (prog.1 - prog.128)
* The Tone of the voices already ON before receiving a program change
message isn't affected.
The Tone will be changed by a new Note-on message after the program
change is received.
* Ignored when "Rx.Program change = OFF".
* In the drum part, Program change messages are ignored when the Bank is set
at 129 - 16384 (ie. the value of the control change number 0 is not 00H).
•Channel pressure
Status Second
DnH vvH
n=MIDI channel number :0H - FH (ch.1 - ch.16)
vv=Value :00H - 7FH (0 - 127)
* Effect to the parameter set on "MOD controller function".
The default setting has no effect.
* Ignored when "Rx.Channel pressure = OFF".
•Pitch bend change
Status Second Third
EnH llH mmH
n=MIDI channel number :0H - FH (ch.1 - ch.16)
mm,ll=Value :00 00H - 40 00H - 7F 7FH (-8192 - 0 - +8191)
* Effect to the parameter set on "MOD controller function".
The default setting is pitch bend.
* Ignored when "Rx.Pitch bend change = OFF"