Page 3
Preface Notice The company reserves the right to revise this publication or to change its contents without notice. Information contained herein is for reference only and does not constitute a commitment on the part of the manufacturer or any subsequent vendor. They assume no responsibility or liability for any errors or inaccuracies that may appear in this publication nor are they in anyway responsible for any loss or damage resulting from the use (or misuse) of this publication.
Preface R&TTE Directive This device is in compliance with the essential requirements and other relevant provisions of the R&TTE Direc- tive 1999/5/EC. This device will be sold in the following EEA countries: Austria, Italy, Belgium, Liechtenstein, Denmark, Lux- embourg, Finland, Netherlands, France, Norway, Germany, Portugal, Greece, Spain, Iceland, Sweden, Ireland, United Kingdom, Cyprus, Czech Republic, Estonia, Hungary, Latvia, Lithuania, Malta, Slovakia, Poland, Slov- enia.
Page 5
Preface CE Marking This device has been tested to and conforms to the regulatory requirements of the European Union and has at- tained CE Marking. The CE Mark is a conformity marking consisting of the letters “CE”. The CE Mark applies to products regulated by certain European health, safety and environmental protection legislation.
Preface FCC Statement (Federal Communications Commission) You are cautioned that changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
Preface FCC RF Radiation Exposure Statement: This Transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator and your body.
Preface IMPORTANT SAFETY INSTRUCTIONS Follow basic safety precautions, including those listed below, to reduce the risk of fire, electric shock, and injury to persons when using any electrical equipment: Do not use this product near water, for example near a bath tub, wash bowl, kitchen sink or laundry tub, in a wet basement or near a swimming pool.
Preface Instructions for Care and Operation The notebook computer is quite rugged, but it can be damaged. To prevent this, follow these suggestions: Don’t drop it, or expose it to shock. If the computer falls, the case and the components could be damaged. Do not expose the computer Do not place it on an unstable Do not place anything heavy...
Page 10
Preface Avoid interference. Keep the computer away from high capacity transformers, electric motors, and other strong magnetic fields. These can hinder proper performance and damage your data. Follow the proper working procedures for the computer. Shut the computer down properly and don’t forget to save your work.
Preface Power Safety The computer has specific power requirements: • Only use a power adapter approved for use with this computer. • Your AC/DC adapter may be designed for international travel but it still requires a Power Safety steady, uninterrupted power supply. If you are unsure of your local power specifications, Warning consult your service representative or local power company.
Preface Polymer Battery Precautions Note the following information which is specific to polymer batteries only, and where applicable, this overrides the general battery precaution information overleaf. • Polymer batteries may experience a slight expansion or swelling, however this is part of the battery’s safety mecha- nism and is not a cause for concern.
Preface Battery Precautions • Only use batteries designed for this computer. The wrong battery type may explode, leak or damage the computer. • Do not remove any batteries from the computer while it is powered on. • Do not continue to use a battery that has been dropped, or that appears damaged (e.g. bent or twisted) in any way. Even if the computer continues to work with a damaged battery in place, it may cause circuit damage, which may possibly result in fire.
Preface Cleaning Do not apply cleaner directly to the computer; use a soft clean cloth. Do not use volatile (petroleum distillates) or abrasive cleaners on any part of the computer. Servicing Do not attempt to service the computer yourself. Doing so may violate your warranty and expose you and the computer to electric shock.
Preface Travel Considerations Packing As you get ready for your trip, run through this list to make sure the system is ready to go: Check that the battery pack and any spares are fully charged. Power off the computer and peripherals. Close the display panel and make sure it’s latched.
Page 16
Preface On the Road In addition to the general safety and maintenance suggestions in this preface, and Chapter 8: Troubleshooting, keep these points in mind: Hand-carry the notebook - For security, don’t let it out of your sight. In some areas, computer theft is very common.
Page 17
Preface Developing Good Work Habits Developing good work habits is important if you need to work in front of the computer for long periods of time. Improper work habits can result in discomfort or serious injury from repetitive strain to your hands, wrists or other joints.
Preface Lighting Proper lighting and comfortable display viewing angle can reduce eye strain and muscle fatigue in your neck and shoulders. • Position the display to avoid glare or reflections from overhead lighting or outside sources of light. • Keep the display screen clean and set the brightness and contrast to levels that allow you to see the screen clearly. •...
Preface Contents Notice ................................I EuP-Standby and Off Mode Power Consumption Statement: ..............II FCC Statement ............................IV FCC RF Radiation Exposure Statement: ..................... V Instructions for Care and Operation ......................VII Power Safety ...............................IX Polymer Battery Precautions ........................X Battery Precautions .............................XI Cleaning ..............................
Page 20
Preface System Map: LCD Panel Open ........................1-6 LED Indicators ............................1-7 Keyboard ..............................1-8 Function/Hot Key Indicators ........................1-9 Control Center ............................1-10 System Map: Front & Top Views ......................1-11 System Map: Left View ...........................1-12 System Map: Right & Rear Views ......................1-13 System Map: Bottom View ........................1-14 3G Module USIM Card Installation ......................1-15 Docking Port ............................1-16 What to do if you Spill Liquid on the Computer ..................1-17...
Page 21
Preface Touchpad and Buttons/Mouse ........................2-4 Gestures and Device Settings ........................2-5 Audio Features ............................2-8 Power Management Overview ..............................3-1 The Power Sources ............................3-2 AC/DC Adapter ............................3-2 Battery ................................3-2 Turning On the Computer ..........................3-3 Power Plans ...............................3-4 Power-Saving States ..........................3-6 Sleep ................................3-6 Hibernate ..............................3-7 Shut down ..............................3-7 Configuring the Power Buttons .........................3-8 Resuming Operation ..........................3-9...
Page 22
Preface Recharging the Battery with the AC/DC Adapter ...................3-13 Proper handling of the Battery Pack ......................3-14 Battery FAQ .............................3-15 Drivers & Utilities What to Install ............................4-1 Driver Installation ............................4-2 Updating/Reinstalling Individual Drivers ....................4-4 User Account Control ..........................4-5 Windows Security Message ........................4-5 New Hardware Found ..........................4-5 Driver Installation Procedure ........................4-6 Chipset ...............................4-6...
Page 23
Preface Optional Drivers ............................4-9 BIOS Utilities Overview ..............................5-1 The Setup Utility ............................5-2 Failing the POST ............................5-3 Fatal Errors ..............................5-3 Non-Fatal Errors ............................5-3 Setup Screens .............................5-4 Main Menu ..............................5-5 System Time & Date (Main Menu) ......................5-5 SATA Port # (Main Menu) ........................5-6 System/Extended Memory: (Main Menu) ....................5-6 MB Series / BIOS Revision / KBC/EC firmware Revision ..............5-6 Advanced Menu ............................5-7...
Page 24
Preface USB 2.0 Combo Port Power / Powered USB 2.0 Port Power (Advanced Menu > Advanced Chipset Control) ........5-9 Intel Smart Connect Technology (Advanced Menu ) ................5-9 Intel Anti-Theft Technology (Advanced Menu ) ..................5-9 SATA Mode (Advanced Menu) ......................5-10 Boot Logo (Advanced Menu) ........................5-10 Power On Boot Beep (Advanced Menu) ....................5-10 Battery Low Alarm Beep (Advanced Menu) ...................5-10 Security Menu ............................5-11...
Page 25
Preface Upgrading The Computer Overview ..............................6-1 When Not to Upgrade ..........................6-2 Removing the Battery ..........................6-3 Removing/Replacing the Component Bay Cover ..................6-4 Upgrading the Hard Disk Drive .........................6-5 Upgrading the System Memory (RAM) ....................6-10 Modules & Options Overview ..............................7-1 PC Camera Module ............................7-3 PC Camera Driver Installation ........................7-4 Wireless LAN Module ..........................7-11 Wireless LAN Switch ..........................7-12...
Page 27
Preface Profiles ..............................7-79 User Options ............................7-81 Text Messaging Service (SMS) .......................7-83 SMS Express ............................7-83 Sending a Text Message ..........................7-84 Inbox ................................7-85 Bluetooth & WLAN Combo Module ......................7-86 3rd Party Bluetooth (V4.0) Combo Driver Installation ................7-87 Intel Bluetooth Combo Driver Installation ....................7-88 Standard Bluetooth Configuration in Windows 7 ...................7-89 Intel Rapid Storage Technology ......................7-93 IRST Driver Installation ..........................7-93...
Page 28
Preface Intel® Smart Connect Technology Configuration .................7-116 Intel® Wireless Display Application .....................7-119 Intel® WiDi Application Installation ....................7-120 Intel® Wireless Music Driver Installation .....................7-120 Intel® WiDi Application Configuration ....................7-121 Troubleshooting Overview ..............................8-1 Basic Hints and Tips ..........................8-2 Backup and General Maintenance ......................8-3 Viruses ...............................8-4 Upgrading and Adding New Hardware/Software ..................8-5 Problems and Possible Solutions .......................8-7...
Page 29
Preface Video Driver Installation ..........................C-1 Dynamic Video Memory Technology ......................C-1 Intel® Graphics & Media Control Panel ....................C-2 Display Devices & Options ........................C-4 Attaching Other Displays .........................C-5 Configuring an External Display in Windows 7 ..................C-8 HDMI Audio Configuration ........................C-11 Specifications Processors For All Models ........................D-2 Processor For Model A Only ........................D-2 Core Logic ..............................D-2 Display ..............................D-2...
Page 30
Preface Communication ............................D-4 Communication (Model A Only) ......................D-4 Communication (Model B Only) ......................D-4 Power Management ..........................D-4 Power ................................D-4 Security ..............................D-4 Indicators ..............................D-4 Operating System ............................D-4 Design Features ............................D-5 Environmental Spec ..........................D-5 Dimensions & Weight ..........................D-5 Docking Station Guide Overview ..............................E-1 Compatibility ............................
Page 31
Preface Cold Undocking the Computer from the Docking Station ..............E-10 Hot Docking the Computer to the Docking Station ................E-11 Hot Undocking the Computer from the Docking Station ............... E-14 Power Button Configuration ........................E-17 Docking Station Ports & Jacks ....................... E-18 Multiple Displays ............................
Page 32
Preface Windows 8 Start Screen & Desktop ......................F-2 Apps & Tiles ............................. F-3 Accessing Pining/Unpinning All Apps ..................... F-3 Desktop Application ..........................F-4 Windows 8 Charms Bar ..........................F-6 Charms Bar Items ............................. F-7 Windows 8 Control Panel ......................... F-8 Windows 8 Taskbar ..........................
Page 33
Preface Driver Installation (Windows 8) ......................F-23 PC Camera (Windows 8) ........................F-25 Metro UI Camera App ..........................F-26 Taking Pictures/Capturing Video ......................F-28 Wireless LAN Settings (Windows 8) ..................... F-30 WLAN Configuration in Windows 8 ..................... F-31 Charms Bar ............................. F-31 Desktop Mode ............................
Quick Start Guide Chapter 1: Quick Start Guide Overview This Quick Start Guide is a brief introduction to the basic features of your computer, to navigating around the computer and to getting your system started. The remainder of the manual covers the following: •...
Quick Start Guide Advanced Users If you are an advanced user you may skip over most of this Quick Start Guide. However you may find it useful to refer to “What to Install” on page 4 - “BIOS Utilities” on page 5 - 1 “Upgrading The Computer”...
Quick Start Guide Not Included Operating Systems (e.g. Windows 7) and applications (e.g. word processing, spreadsheet and database programs) have their own manuals, so please consult the appropriate manuals. Drivers If you are installing new system software, or are re-configuring your computer for a different system, you will need to install the drivers listed in “Drivers &...
Quick Start Guide System Startup Remove all packing materials. Place the computer on a stable surface. Securely attach any peripherals you want to use with the notebook (e.g. keyboard and mouse) to their ports. Attach the AC/DC adapter to the DC-In jack on the left of the computer, then plug the AC power cord into an outlet, and connect the AC power cord to the AC/DC adapter.
Quick Start Guide System Software Your computer may already come with system software pre-installed. Where this is not the case, or where you are re-configuring your computer for a different system, you will find the Windows 7 (with Service Pack 1 in- stalled) and Windows 8 operating systems are supported.
Quick Start Guide System Map: LCD Panel Open Figure 1 - 2 LCD Panel Open Built-In PC Camera Wireless Device (Optional) Operation Aboard Aircraft Power Button Keyboard The use of any portable elec- Built-In Microphone tronic transmission devices Touchpad & aboard aircraft is usually pro- Buttons hibited.
Quick Start Guide LED Indicators The LED indicators on the computer display helpful information about the current status of the computer. Icon Color Description Icon Color Description DC Power is Plugged Orange Blue Power Button The Powered USB Port Green Hard Disk Activity is On* (System Off) Blinking...
Quick Start Guide Keyboard The keyboard has an embedded numerical keypad for easy numeric data input, and Other Keyboards features function keys to allow you to change operational features instantly. See Table , on page 1 - 9 for full function key combination details and Appendix F If your keyboard is damaged or you just...
Quick Start Guide Function/Hot Key Indicators The function keys (F1 - F12 etc.) will act as hot keys when pressed while the Fn key is held down. In addition to the basic function key combinations; visual indicators are available when the hot key utility is installed. Keys Function Keys...
Quick Start Guide Control Center Press the Fn + Esc key combination to toggle the Control Center on/off. The Control Center gives quick ac- cess to frequently used controls and enables you to quickly turn modules on/off. Undocking Click the Docking but- ton to hot undock the system (if your comput- er supports hot undock-...
Quick Start Guide System Map: Front & Top Views Figure 1 - 4 Front & Top Views (with Optional Docking Station) LED Indicators WLAN Switch Docking Station (Optional) WLAN Switch Use the WLAN Switch (for Wireless LAN only) to toggle power to the WLAN module.
Quick Start Guide System Map: Left View Figure 1 - 5 Left View DC-In Jack External Monitor Port RJ-45 LAN Jack e-SATA Port/ USB 2.0 Combo Port External Monitor Port & RJ-45 LAN Multi-In-1 Push-Push Card Reader HDMI Out Port Jack 2 * USB 3.0 Ports The card reader allows you to use the most...
Quick Start Guide System Map: Right & Rear Views Figure 1 - 6 Right & Rear Views Microphone-In Jack Headphone-Out Jack 1 * Powered USB 2.0 Port Fan Intake/Vent Security Lock Slot Battery Powered USB 2.0 Port The powered USB 2.0 port can supply power (for charging devices only, not for operating devices) when the system is off but still powered by the AC/DC adapter plugged into a working outlet, or powered by the battery with a capacity level above 20% (this may not work with cer-...
Quick Start Guide System Map: Bottom View Figure 1 - 7 Bottom View Battery Docking Port The CPU is not a user ser- Fan Intake/Vent viceable part. Drainage Outlet Speakers Overheating Component Bay To prevent your computer Cover from overheating make sure nothing blocks the...
Quick Start Guide 3G Module USIM Card Installation If you have included an optional 3G module in your purchase option, follow the instructions below to install the USIM card (which will be provided by your service provider), and then run the Mobile Partner application. See “Wireless Manager”...
Quick Start Guide Docking Port Follow the instructions below before connecting the computer to the docking station, if included in your pur- chase configuration. Failure to open the cover of the docking port before connecting the computer to the docking station may result in irreparable damage to the connector on the docking station.
Quick Start Guide What to do if you Spill Liquid on the Computer The keyboard incorporates a drainage system that minimizes the chances of liquid Warranty Warning spillages on the keyboard penetrating the inside components of the computer. Liquid spilled on the computer is drained towards the right side of the computer.
Page 52
Quick Start Guide 3. Move the computer to a dry place and wipe any liquid off the keyboard and bottom of the computer using a clean, soft, dry cloth. 4. Remove the battery. 5. Leave the computer resting on its right side (while placed on a clean, soft, dry cloth) to dry out for about three hours.
Quick Start Guide Windows 7 Start Menu & Control Panel Most of the control panels, utilities and programs within Windows 7 are accessed from the Start menu (see pendix F for information on the Windows 8 OS). When you install programs and utilities they will be installed on your hard disk drive, and a shortcut will usually be placed in the Start menu and/or the desktop.
Quick Start Guide Video Features You can switch display devices, and configure display options, from the Display control panel (in Appearances and Personalization) in Windows 7 (see over). For more detailed video information see “Video Driver Con- trols” on page C - 1.
Page 55
Quick Start Guide To access the Intel(R) Graphics and Media Control Panel: Click Advanced settings (Figure 1 - 13 on page 1 - 20) in the Display Settings control panel in Windows. Click Graphics Properties (button) (Figure 1 - 14) in the Intel Graphics & Media Control Panel tab. Right-click the desktop and select Graphics Properties from the menu.
Quick Start Guide Power Options The Power Options (Hardware and Sound menu) control panel icon in Windows (see page 1 - 19 or see pendix F for information on the Windows 8 OS) allows you to configure power management features for your computer.
Features & Components Chapter 2: Features & Components Overview External Optical (CD/DVD) Device Read this chapter to learn more about the following main features and components Drives of the computer: To install applications and drivers etc. you will • Hard Disk Drive need to attach an exter- •...
Features & Components Hard Disk Drive The hard disk drive is used to store your data in the computer. The hard disk can be Power Safety taken out to accommodate other 2.5" serial (SATA) hard disk drives with a height of 9.5 mm.
Features & Components Multi-In-1 Card Reader The card reader allows you to use some of the latest digital storage cards. Push the Card Reader Cover card into the slot and it will appear as a removable device, and can be accessed in the same way as your hard disk (s).
Features & Components ExpressCard Slot The computer is equipped with an ExpressCard/34/54 slot that reads Express Card/ ExpressCard 34 and ExpressCard/54 formats. ExpressCards are the successors to PCMCIA (PC Slot Cover Cards). Make sure you install the Card Reader driver (see “CardReader”...
Features & Components Touchpad and Buttons/Mouse The Touchpad is an alternative to the mouse; however, you can also add a mouse to Touchpad Scrolling your computer through one of the USB ports. The Touchpad buttons function in much the same way as a two-button mouse. This computer model se- ries may feature different Touchpad versions.
Features & Components Gestures and Device Settings The Synaptics Gestures Suite application allows you to use a specific gesture (ac- Show Video tion) on the surface of the Touchpad to perform specific actions to manipulate doc- uments, objects and applications. You can get a clearer view of the gestures in- You can configure the settings from the Device Settings tab in Mouse Properties:...
Page 63
Features & Components Scrolling The Two-Finger scrolling feature works in most scrollable windows and allows you to scroll horizontally and vertically. Place two fingers, slightly separated, on the Touchpad surface and slide both fingers in the direction required (in a straight con- Figure 2 - 6 tinuous motion).
Page 64
Features & Components Rotating Use the Pivot Rotate gesture to rotate objects (e.g. photos) in 90 degree increments. Place a finger down on the left “target” zone and keep it stationary. Place another finger near the middle of the Touchpad and slide it in a circular motion around the stationary finger (clockwise or counterclockwise) to rotate the object.
Features & Components Audio Features You can configure the audio options on your computer from the Sound control Sound Volume panel in Windows, from the HD VDeck icon on the desktop or VIA HD Audio Adjustment Deck control panel The sound volume level is set using the volume The volume may also be adjusted by means of the Fn + F5/F6 key combination.
Page 66
Features & Components Expert Mode will allow you to access more advanced configuration menus for Speaker, Microphone and Stereo Mix. Syncing Left & Right Volume Balance If you wish to adjust the left and right channel volume levels separately, you will need to adjust this from the VIA HD Audio Deck in Ex- pert Mode.
Power Management Chapter 3: Power Management Overview OS Note Power management To conserve power, especially when using the battery, your computer power man- functions will vary slight- agement conserves power by controlling individual components of the computer ly depending on your (the LCD and hard disk drive) or the whole system.
Power Management The Power Sources The computer can be powered by either an AC/DC adapter or a battery pack. AC/DC Adapter Use only the AC/DC adapter that comes with your computer. The wrong type of AC/ DC adapter will damage the computer and its components. Attach the AC/DC adapter to the DC-in jack on the left of the computer.
Power Management Turning On the Computer Now you are ready to begin using your computer. To turn it on simply press the pow- Forced Off er button on the front panel. If the system “hangs”, When the computer is on, you can use the power button as a Stand by/Hibernate/ and the Ctrl + Alt + Del Shutdown hot-key button when it is pressed for less than 4 seconds (pressing and key combination doesn’t...
Power Management Power Plans The computer can be configured to conserve power by means of power plans. You Resuming can use (or modify) an existing power plan, or create a new one. Operation The settings may be adjusted to set the display to turn off after a specified time, and Table 3 - 1, on to send the computer into Sleep after a period of inactivity.
Page 71
Power Management Each Windows power plan will also adjust the processor performance of your ma- chine in order to save power. This is worth bearing in mind if you are experiencing any reduced performance (especially under DC/battery power). Choose High performance (you may need to click Show additional plans to view the High performance plan) for maximum performance when the computer is pow- ered from an AC power source.
Power Management Power-Saving States You can use power-saving states to stop the computer’s operation and restart where you left off. Win 7 uses the Sleep, Hibernate and Shut Down power-saving states. Sleep In Sleep all of your work, settings and preferences are saved to memory before the system sleeps.
Power Management Hibernate Hibernate uses the least amount of power of all the power-saving states and saves all of your information on a part of the hard disk before it turns the system off. If a power failure occurs the system can restore your work from the hard disk; if a power failure occurs when work is saved only to memory, then the work will be lost.
Power Management Configuring the Power Buttons The power/sleep button (Fn + F4 key combo) and closed lid may be set to send the Password computer in to a power-saving state. Click Choose what the power buttons do on Protection the left menu in Power Options to bring up the menu.
Power Management Resuming Operation You can resume operation from power-saving states by pressing the power button, or in some cases pressing the sleep button (Fn + F4 key combo). Closing the Lid If you have chosen to Power Status To Resume Icon Color...
Power Management Power Conservation Modes This system supports Energy Star power management features that place comput- ers (CPU, hard drive, etc.) into a low-power sleep modes after a designated period Power Conservation of inactivity. Adjust Power Conservation Modes from the Control Center: Modes The Energy Star setting Press the Fn + Esc key combination to toggle the Control Center on/off.
Power Management Battery Information Follow these simple guidelines to get the best use out of your battery. Low Battery Warning Battery Power Your computer’s battery power is dependent upon many factors, including the pro- When the battery is criti- cally low, immediately grams you are running, and peripheral devices attached.
Power Management Conserving Battery Power • Use a power plan that conserves power (e.g Power saver), however note that this may have an affect on computer performance. Windows Mobility Center • Lower the brightness level of the LCD display. The system will decrease LCD brightness slightly to save power when it is not powered by the AC/DC adapter.
Power Management Battery Life Battery life may be shortened through improper maintenance. To optimize the life and improve its performance, fully discharge and recharge the battery at least once every 30 days. We recommend that you do not remove the battery yourself. If you do need to re- move the battery for any reason (e.g.
Power Management Proper handling of the Battery Pack • DO NOT disassemble the battery pack under any circumstances • DO NOT expose the battery to fire or high temperatures, it may explode Caution • DO NOT connect the metal terminals (+, -) to each other Danger of explosion if battery is incorrectly re- placed.
Power Management Battery FAQ How do I completely discharge the battery? Use the computer with battery power until it shuts down due to a low battery. Don’t turn off the computer even if a message indicates the battery is critically low, just let the computer use up all of the battery power and shut down on its own.
Page 82
Power Management Click Change plan settings (after creating it) and click Change plan settings > Change advanced power settings. Figure 3 - 9 Change Plan Settings / Change Advanced Power Settings 3 - 16 Battery Information...
Page 83
Power Management Scroll down to Battery and click + to expand the battery options. Choose the options below (click Yes if a warning appears): Figure 3 - 10 Power Options Advanced Settings - Battery • Low battery levels = 0% •...
Page 84
Power Management How do I fully charge the battery? When charging the battery, don’t stop until the LED charging indicator light changes from orange to green. How do I maintain the battery? Completely discharge and charge the battery at least once every 30 days or after about 20 partial discharges.
Drivers & Utilities Chapter 4: Drivers & Utilities This chapter deals with installing the drivers and utilities essential to the operation or improvement of some of the computer’s subsystems. The system takes advantage of some newer hardware components for which the lat- est versions of most available operating systems haven’t built in drivers and utilities.
Drivers & Utilities Driver Installation Check the driver installation order from Table 4 - 1, on page 4 - 3 (the drivers must be installed in Insert the Device Drivers & Utilities + User’s Manual this order) which is the same as that listed in the disc and click Install Drivers (button), or Option Driv- Drivers Installer menu below.
Drivers & Utilities Manual Driver Installation Updating/Reinstalling Individual Drivers Click Browse CD/DVD (button) in the Drivers Install- If you wish to update/reinstall individual drivers it er application and browse to the executable file in the may be necessary to uninstall the original driver.To do appropriate driver folder.
Drivers & Utilities User Account Control New Hardware Found If a User Account Control prompt appears as part of If you see the message “New Hardware Found” dur- the driver installation procedure, click Continue or ing the installation procedure (other than when out- Allow, and follow the installation procedure as direct- lined in the driver install procedure), click Cancel to close the window, and follow the installation proce-...
Drivers & Utilities Hot Key Audio 1. Click 6.Install Hotkey AP > Yes. 1. Click 9.Install Audio Driver > Yes. 2. Click Next > Next. 2. Click Next. 3. Click Finish > Finish to restart the computer. 3. Click the button to agree to the license and click Next.
Drivers & Utilities Windows Experience Index After the drivers are installed follow this procedure to ensure an accurate rating from the Windows Experi- Windows Update ence Index (make sure the AC/DC adapter is plugged After installing all the drivers make sure you enable Win- in): dows Update in order to get all the latest security up- dates etc.
Drivers & Utilities Optional Drivers See the pages indicated in Table 4 - 1, on page 4 - 3 for the driver installation procedures for any modules in- cluded in your purchase option. Figure 4 - 3 - Drivers Installer - Option Drivers Menu Note that you need to install both the WLAN &...
BIOS Utilities Chapter 5: BIOS Utilities BIOS Screens Overview Note that BIOS This chapter gives a brief introduction to the computer’s built-in software: screens pictured these pages are intend- If your computer has never been set up, or you are making important changes to the ed for guidance in set- ting up your system’s system (e.g.
BIOS Utilities The Setup Utility Each time you turn on the computer the system takes a few seconds to conduct a BIOS Settings POST, including a quick test of the on-board RAM (memory). Warning As the POST proceeds, the computer will tell you if there is anything wrong. If there Incorrect settings can is a problem that prevents the system from booting, it will display a system summary cause your system to...
BIOS Utilities Failing the POST Errors can be detected during the POST. There are two categories, “fatal” and “non- fatal”. Fatal Errors These stop the boot process and usually indicate there is something seriously wrong with your system. Take the computer to your service representative or authorized service center as soon as possible.
BIOS Utilities Setup Screens The following pages contain additional advice on portions of the Setup. Along the top of the screen is a menu bar with menu headings. When you select a heading, a Setup Menus new screen appears. Scroll through the features listed on each screen to make chang- Setup menus es to Setup.
BIOS Utilities Main Menu Figure 5 - 2 Main Menu System Time & Date (Main Menu) The hour setting uses the 24-hour system (i.e., ØØ = midnight; 13 = 1 pm). If you can change the date and time settings in your operating system, you will also change these settings.
BIOS Utilities SATA Port # (Main Menu) Pressing Enter opens the sub-menu to show the configuration of a optical Device/ HDD on the computer’s SATA Ports. System/Extended Memory: (Main Menu) This item contains information on the system memory, and is not user configurable. The system will auto detect the amount of memory installed.
BIOS Utilities Advanced Menu Figure 5 - 3 Advanced Menu Advanced Chipset Control (Advanced Menu) The sub-menu here allows you to adjust the Bluetooth Power Setting and enable/ disable VT-d, Intel Virtualization Technology, Intel TXT(LT) Support and USB 3.0 Port power/ Card Reader/ExpressCard power/USB 2.0 Port power. Advanced Menu 5 - 7...
BIOS Utilities Bluetooth Power Setting (Advanced Menu > Advanced Chipset Control) You can adjust the Bluetooth module power setting to your preference. The default setting (Disabled) will see the Bluetooth module powered off when the system is started up or restarted. Enabling the power setting will have the module retain the last power status (on or off) before any restart or shut down.
BIOS Utilities USB 3.0 Power/ Card Reader Power / PCI Express Card Power / USB 2.0 Combo Port Power / Powered USB 2.0 Port Power (Advanced Menu > Advanced Chipset Control) These menu items allow you to enable/disable power to the card reader, Express Card or USB ports when required to do so in order to save power.
BIOS Utilities SATA Mode (Advanced Menu) You can configure SATA (Serial ATA) control to operate in IDE (native/compati- ble), AHCI (Advanced Host Controller Interface) modes from this menu. The SATA Mode SATA Mode should be set BEFORE installing an operating system, and after you If you have installed the have backed up all necessary files and data (see sidebar).
BIOS Utilities Security Menu Security Menu The changes you make here affect the access to the Setup utility itself, and also access to your machine as it boots up after you turn it on. These settings do not affect your machine or network passwords which will be set in your...
BIOS Utilities Set User Password (Security Menu) You can set a password for user mode access to the Aptio Setup Utility. This will not affect access to the computer OS, (only the Setup utility) unless you choose to Password Warning set a Password on Boot (see below).
BIOS Utilities TPM Configuration (Security Menu) This sub-menu will allow you to enable/disable Trusted Platform Module (TPM) support, and to configure the TPM State. Select TPM Configuration and press En- ter to access the sub-menu. Press Enter to access the Security Device Support menu and select Enable to display the full TPM configuration menu (see “Trusted Platform Module”...
BIOS Utilities TPM State (Security Menu > TPM Support Enabled) Select TPM State, press Enter and select Enable to change the TPM state to en- abled. You will then need to press F4 to save the changes and restart the computer. Figure 5 - 6 TPM State (Enabled) As the computer restarts press F2 to enter the BIOS again and go to the TPM Con-...
BIOS Utilities Pending TPM operation (Security Menu > TPM Support & TPM State Enabled) Select Pending operation, press Enter and select the option you require (if you are initializing TPM you should select Enable Take Ownership). You will then need to press F4 to save the changes and restart the computer.
BIOS Utilities Boot Menu Figure 5 - 8 Boot Menu BIOS Screens Note that BIOS screens pictured these pages are intend- ed for guidance in set- ting up your system’s BIOS. BIOS versions are sub- ject to constant change and revision, therefore your computer’s actual When you turn the computer on it will look for an operating system (e.g.
BIOS Utilities Boot Option Priorities (Boot Menu) Press Enter to access the menu and use the arrow keys to move up and down the available options (the selected device will be highlighted in white). OS Select (Boot Menu) This item tells allows you to set the operating system you intend to use. This item should be set before you install an operating system.
BIOS Utilities Exit Menu Figure 5 - 9 Exit Menu Click Save Changes and Reset to save all changes made. Choosing to Discard Changes, or Exit Discarding Changes, will wipe out any changes you have made to the Setup. You can also choose to restore the original Setup defaults that will re- turn the Setup to its original state, and erase any previous changes you have made in a previous session.
Upgrading The Computer Chapter 6: Upgrading The Computer Overview This chapter contains information on upgrading the computer. Follow the steps out- Warranty Warning lined to make the desired upgrades. If you have any trouble or problems you can con- tact your service representative for further help.
Upgrading The Computer When Not to Upgrade These procedures involve opening the system’s case, adding and sometimes replac- ing parts. Power Safety Warning You should not perform any of these upgrades if: Before you undertake • Your system is still under warranty or a service contract upgrade proce- dures, make sure that...
Upgrading The Computer Removing the Battery If you are confident in undertaking upgrade procedures yourself, for safety reasons Warranty Warning it is best to remove the battery. Please check with your Turn the computer off, and turn it over. service representative Slide the latch...
Upgrading The Computer Removing/Replacing the Component Bay Cover Turn off the computer, and turn it over and remove the battery. Warranty Warning Slide the latch in the direction of the arrow. Slide the latch in the direction of the arrow, and hold it in place. Please check with your Carefully slide the cover in the direction of the arrow to align with the markers...
Upgrading The Computer Upgrading the Hard Disk Drive The hard disk drive can be taken out to accommodate other 2.5" serial (SATA) hard HDD System disk drives with a height of 9.5mm (h) (see “Storage” on page D - 3).
Page 118
Upgrading The Computer Turn off the computer, and turn it over and remove the component bay cover (see “Removing/Replacing the Component Bay Cover” on page 6 - Raise the plastic tab Slide the hard disk assembly in the direction of arrow until you can see the (gold colored) HDD connector Figure 6 - 3...
Page 119
Upgrading The Computer Remove the screw(s) & and the adhesive cover Figure 6 - 5 Hard Disk Cover Removal Upgrading the Hard Disk Drive 6 - 7...
Page 120
Upgrading The Computer Reinserting the HDD To reinsert the HDD assembly hold it carefully at the four corners between your thumb and forefinger. Figure 6 - 6 Hard Disk Insertion Hard Disk Handling Insert the HDD directly down into the bay vertically Do not press down on the center off the hard disk as Press and slide the HDD assembly at the area illustrated...
Page 121
Upgrading The Computer Press down on the rubber case to ensure the assembly is properly seated before replacing the cover and screws. Figure 6 - 8 Seat the Assembly Replace the component bay cover (see “Removing/Replacing the Component Bay Cover” on page 6 - Upgrading the Hard Disk Drive 6 - 9...
Upgrading The Computer Upgrading the System Memory (RAM) The computer has two memory sockets for 204 pin Small Outline Dual In-line (SO- DIMM) DDRIII (DDR3) type memory modules (see “Memory” on page D - 3 details of supported module types). Turn off the computer, and turn it over and remove the component bay cover (“Removing/Replacing the Component Bay Cover”...
Page 123
Upgrading The Computer Gently pull the two release latches on the sides of the memory socket in the direction indicated by the arrows ( & Figure 6 - Figure 6 - 10 RAM Module Release Latches Contact Warning Be careful not to touch The RAM module will pop-up, and you can remove it.
Page 124
Upgrading The Computer Pull the latches to release the second module if necessary. Insert a new module holding it at about a 30° angle and fit the connectors firmly into the memory slot. The module’s pin alignment will allow it to only fit one way. Make sure the module is seated as far into the slot as it will go.
Modules & Options Chapter 7: Modules & Options Overview Wireless Device Operation Aboard Aircraft This chapter contains information on the following modules, which may come with your computer, depending on the configuration purchased. If you are unsure please The use of any portable contact your service representative.
Page 126
Modules & Options Important Notice If your purchase option includes both Wireless LAN and 3G modules, then the appropriate antennas will be installed. Note that In order to comply with FCC RF exposure compliance requirements, the antenna must not be co-located or operate in conjunction with any other antenna or transmitter.
Modules & Options PC Camera Module Before installing the PC Camera driver, make sure that the optional PC Camera is Latest PC Camera on. Use the Fn + F10 key combination (see “Function/Hot Key Indicators” on Driver Information page 1 - 9) or Control Center button to toggle power to the PC Camera module.
Modules & Options PC Camera Driver Installation 1. Make sure the module is powered on, and then insert the Device Drivers & Utilities + User’s Manual disc into the CD/DVD drive. PC Camera Screen 2. Click Option Drivers (button). Refresh 3.
Page 129
Modules & Options PC Camera Audio Setup If you wish to capture video & audio with your camera, it is necessary to setup the audio recording options in Windows. Click Start, and click Control Panel (or point to Settings and click Control Panel). Click Sound (Hardware and Sound).
Page 130
Modules & Options Figure 7 - 1 Audio Setup for PC Camera Right-click 7 - 6 PC Camera Module...
Page 131
Modules & Options Camera Application The camera application is a video viewer for general purpose video viewing and test- ing, and for capturing video files to .avi format. Run the camera application from the desktop shortcut (it is recommended that you set the capture file before the capture process - see Set Capture File below).
Page 132
Modules & Options Reducing Video File Size Note that capturing high resolution video files requires a substantial amount of disk space for each file. After recording video, check the video file size (right-click the file and select Properties) and the remaining free space on your hard disk (go to My Computer, right-click the hard disk, and select Properties).
Page 133
Modules & Options Eliminating Screen Flicker If you find that the video screen in the camera program is flickering, you can try to adjust the setting in the Video Capture Filter options. Latest PC Camera Driver Information Run the camera application from the desktop shortcut. Go to Options and scroll down to select Video Capture Filter..
Page 134
Modules & Options Taking Still Pictures The camera application allows you to take still pictures. Snapshot Folder Run the camera application from the desktop shortcut. Go to Options and select Take Picture. The Snapshot folder’s The picture (in JPEG format) will be placed in the Snapshot folder on the default location is on the desktop.
Modules & Options Wireless LAN Module If you have included an Intel® or 3rd Party Wireless LAN (or WLAN & Bluetooth Wireless Device combo) module in your purchase option, make sure that the WLAN module is on be- Operation Aboard fore installing the driver.
Modules & Options Wireless LAN Switch The Wireless LAN switch allows you to quickly and easily toggle power to the WLAN module when necessary. Figure 7 - 3 Front View WLAN Switch You can also use the Fn + F11 key combination (see page 9) or the Windows Mobility Center (see page 34) button to toggle power to the WLAN module,...
Modules & Options 3rd Party 802.11b/g/n Driver Installation (for WLAN Module) If you see the message “Found New Hardware” click Cancel to close the window. 1. Make sure the module is powered on, and then insert the Device Drivers & Utilities + User’s Manual disc into the CD/DVD drive. 2.
Modules & Options Intel® WLAN Driver Installation The WLAN driver installation procedure for Intel WLAN modules will depend on the Intel WLAN module version installed. There are two Intel WLAN driver ver- sions available, and if you click the 2.Install WLAN Driver button in Option Driv- ers the appropriate driver will be installed for you.
Modules & Options Intel® WLAN Driver Installation (Driver Version 1) If you see the message “Found New Hardware” click Cancel to close the window. 1. Make sure the module is powered on, and then insert the Device Drivers & Utilities + User’s Manual disc into the CD/DVD drive. 2.
Modules & Options Intel® WLAN Driver Installation (Driver Version 2) Typical Installation: 1. If you see the message “Found New Hardware” click Cancel to close the window. 2. Make sure the module is powered on, and then insert the Device Drivers &...
Modules & Options Intel® WLAN Driver Installation (Driver Version 2) Custom Installation (for Intel® ProSet and/or Intel® MyWiFi Technology): Note that if you wish to install Intel® MyWiFi you will need to install Micro- soft.net Framework 4.0 (or later version) before installing the driver as per the procedure below.
Modules & Options Connecting to a Wireless Network in Windows 7 Make sure the Wireless LAN module is turned on. Click the taskbar notification area wireless icon , and then double-click an Network and access point to connect to or click to Open Network and Sharing Center if you do Sharing Center not see a network you want to connect to in the taskbar menu (a list of options will You can also use the Net-...
Page 144
Modules & Options You may need to enter a security key for any access point to which you are trying to connect. Click to select a network location (e.g. Home, Work or Public). Click “View or change settings in Network and Sharing Center” to access further options for the connection.
Page 145
Modules & Options Click the taskbar icon to see any currently connected networks. To disconnect from the wireless network you can click the taskbar wireless icon click the active connection and then click Disconnect (button). Security Enabled Networks You should try to make sure that any network you are connecting to is a se- cure network.
Modules & Options Intel Connecting to a Wireless Network Using ® PROSet Wireless (For Intel® WLAN modules using driver version 2 only) Make sure the Wireless LAN module is on. Access the Intel® WiFi Connection Utility from the Start menu (Start > All Programs >...
Page 147
Modules & Options Click Connect to connect to the select WiFi network access point. If the access point is encrypted then you will need to enter the password and click Figure 7 - 9 Intel® PROSet/ Wireless WiFi Connection Utility (Connecting &...
Modules & Options Intel My WiFi Configuration ® (For Intel® WLAN modules using driver version 2 only) Intel® My WiFi Technology (Intel® MWT) uses your WLAN to transform your Intel® My WiFi Help system into a Wi-Fi Personal Area Network, and enables you wirelessly share your To get help on Intel®...
Page 149
Modules & Options Intel® My WiFi Configuration You can configure the My WiFi settings as follows. Make sure the Wireless LAN module is on. Access the Intel® WiFi Connection Utility from the Start menu (Start > All Programs > Intel PROSet Wireless > Intel(R) My WiFi Dashboard), or click the icon in the notification area of the taskbar (or right-click and select Open Dashboard).
Page 150
Modules & Options Intel® My WiFi Interface Help Wireless ON/OFF Configuration Options & Preferences Figure 7 - 11 Intel® My WiFi Utility - Interface Your Computer 7 - 26 Wireless LAN Module...
Page 151
Modules & Options Intel® My WiFi Help Click the Help icon in the dashboard to bring up the Help menu and select and item from the Contents menu to obtain the help information. Help Figure 7 - 12 Intel® My WiFi Utility - Help Your Wireless LAN Module 7 - 27...
Page 152
Modules & Options Preferences Click the Options icon and select Preferences to configure the options. Help Figure 7 - 13 Intel® My WiFi Utility - Preferences Your Computer 7 - 28 Wireless LAN Module...
Page 153
Modules & Options Hotspot You can turn the computer into a hotspot to allow other devices to connect to it (and any locally connected devices), and also (if available) the internet. Click the Hotspot icon to turn the Hotspot on. The Hotspot settings tab shows the SSID and password (you will need to enter this information when accessing the hotspot from the client computer/device).
Page 154
Modules & Options Finding Devices You can find any Nearby Devices by clicking the Refresh button in the main window. Click again at any time to update the list. If a lot of devices are found they will be listed on multiple pages and you can use the left or right buttons to turn the pages.
Page 155
Modules & Options Favorite Devices The Favorite Devices tab is where you keep devices to which you connect most of- ten, and this is particularly useful in environments where many devices are listed nearby. A favorite device will display the icon To make any device a favorite just click to select it and select Add Favorite.
Page 156
Modules & Options Connect to a Device Click the device you want to connect to, and click the connect icon An invitation will be sent to the target device. The user must then accept the invitation. After the invitation is accepted the connection will be made. Use the Windows Network and Sharing Center to set permissions for viewing and sharing the resources on your computer with another connected computer.
Page 157
Modules & Options Changing WLAN Modules in Computers with Intel® vPro™ Technology If you change or replace you WLAN module in a computer with Intel® vPro™ Technology, you may receive an error message. To correct any error message in this Intel®...
Modules & Options Windows Mobility Center The Windows Mobility Center control panel provides an easy point of access for information on battery status, power plans used and wireless device status etc. To access the Windows Mobility Center: Click Start, and click Control Panel (or point to Settings and click Control Panel).
Modules & Options Security Modules (Fingerprint & TPM) The encrypted channel between the Trusted Platform Module security chip (see Password Warning “Intel® Management and Security Status” on page 7 - 96) and the fingerprint reader with AuthenTec TrueSuite software (see “Fingerprint Reader Module”...
Modules & Options Fingerprint Reader Module The fingerprint reader module provides a high level of security for your computer. Make sure you have administrator’s rights to your computer, and have a Windows password enabled for full security protection. Fingerprint Reader Driver Installation 1.
Modules & Options AuthenTec TrueSuite Application The AuthenTec TrueSuite application is used in conjunction with your fingerprint reader to enroll fingerprints and manage settings etc. Fingerprint Enrollment User Enrollment Note that it is strongly rec- Click Start > All Programs > AuthenTec TrueSuite > AuthenTec TrueSuite. ommended that you enroll Click Yes when you have identified your fingerprint sensor ( Fingerprint...
Page 162
Modules & Options You will be prompted to select another finger for enrollment (it is recommended that you enroll a number of fingers - see sidebar). Click the button to continue once you have enrolled a number of fingerprints. Help Enter the required information and click the button to register your software, or click to register later.
Page 163
Modules & Options Settings Click the Settings button on the menu bar to access the personalization settings for AuthenTec TrueSuite. Here you can choose to enable/disable Website Log On, QuickLaunch, Fast User Switching and the desktop icon. You can also select the Theme and export/import identities.
Page 164
Modules & Options Windows Log On Windows log on allows you to gain access to your computer by swiping your finger across the fingerprint reader sensor. Use the Biometric Devices control panel (in the Hardware & Sound category) in Windows to turn Biometrics on/off when re- quired.
Page 165
Modules & Options Website Log On Use a fingerprint swipe to log on to websites to help you avoid having to remember user names and passwords across multiple websites (browsers supported are Internet Explorer, Firefox and Chrome). Registering a Website Use your web browser to navigate to the website required.
Page 166
Modules & Options QuickLaunch QuickLaunch allows you to drag and drop icons (which represent websites, folders, applications and/or computer actions) to any enrolled finger and then swipe your fin- ger to launch the icons assigned to that finger. Click Start > All Programs > AuthenTec TrueSuite. Click Select Category (button) to group icons if required.
Page 167
Modules & Options Adding a Website to QuickLaunch Click Start > All Programs > AuthenTec TrueSuite. Click the Add Website button on the menu bar and the dialog box will be displayed. Enter the website URL, name, icon and category as required. Click Save and an icon will be associated with the selected website.
Page 168
Modules & Options Dock View Dock View displays the website icons across the bottom of the screen. Each icon wiLl have an associated web card which displays the website information, user name and password etc. This information may be edited or deleted as required. Figure 7 - 26 Dock View Editing a Web Card...
Page 169
Modules & Options Exporting and Importing Your Identity You can export your identity to backup your information, or to move it to another computer. Exporting Your Identity Click Start > All Programs > AuthenTec TrueSuite. Click the Settings button on the menu bar. Click Export My Identity.
Page 170
Modules & Options AuthenTec KeepSafe The KeepSafe folder is an encrypted area assigned on your hard drive that allows you to store files and folders to be protected by fingerprint protection. The folder will appear on your desktop (if selected in the Personalization Settings) and in My Computer, but will not be visible to other users of your computer.
Modules & Options 3G Module If you have included an optional UMTS/HSPDA OR UMTS/HSPDA+ based 3G Module (Universal Mobile Telecommunications System or High Speed Packet Ac- cess) module (see “Communication” on page D - 4 for specification details) in your purchase option, you will have the appropriate application (Wireless Manager or AirCard Watcher) provided for Windows 7 (see “3G Settings (Windows 8)”...
Page 172
Modules & Options Before installing the application, make sure that the 3G module is ON (installing the driver with the module off will not allow the software to detect the module hard- ware correctly). Use the Fn + key combination (see “Function/Hot Key Indi- 3G Modules &...
Page 173
Modules & Options 3G Module USIM Card Installation Follow the instructions below to install the USIM card (which will be provided by your service provider). Power Safety Warning Turn the computer off, and turn it over. Before you undertake any Slide the latch in the direction of the arrow.
Modules & Options Wireless Manager With the 3G module and USIM card (supplied by your service provider) installed you may then install the Wireless Manager application. The Wireless Manager Wireless Device application allows you to directly access your internet service from the computer. Operation Aboard Aircraft Wireless Manager Installation...
Modules & Options Wireless Manager Application The connection information is stored on the USIM card supplied by the service pro- vider (where this is not the case you may need to create a profile - see “Creating a PIN Number Profile”...
Page 176
Modules & Options The system will connect to your network. Connected will appear above the timer icon (the timer will indicate your connected time for the current session) Wireless Manager You can then access the internet, download e-mail etc. as per any internet Help connection.
Page 177
Modules & Options Click the Wireless Manager notification area icon to view the connection status, or wireless icon to view the Mobile Broadband Connection status Figure 7 - 31 Notification Area Icons (Connected) Notification Area The indicator will display the signal strength and radio access Icon technology.
Modules & Options Profiles Access the Wireless Manager application from the Start menu (Start > All Pro- grams > Wireless Manager > Wireless Manager) or the desktop shortcut Click the Settings > Advanced. Click the Profiles (tab). Figure 7 - 32 Advanced Settings - Profiles 7 - 54 3G Module...
Page 179
Modules & Options Multiple profiles may be available from the USIM card and the first time the application starts it may require you to select a profile (Set Profile) to use for your connection. Figure 7 - 33 Multiple Profiles Found Automatic Profile Selection If Automatic selection is chosen, then the application will search the operator pro-...
Page 180
Modules & Options Selecting a Profile Click Manual selection (button). Click the Filter to view the drop-down list. Select the Profile you wish to use and click Apply to confirm the selection. Figure 7 - 34 Profile - Manual Selection (Filter) 7 - 56 3G Module...
Page 181
Modules & Options Creating a Profile Click Manual selection (button). Click the New. Deleting a Profile Enter a name you prefer for the profile. Enter the Access Point Name (APN). To delete a profile click Enter the User Name and Password if required (some service providers may not to select Manual selec- require this information and the fields may then be left blank).
Modules & Options Settings The Settings tab allows you at adjust the application features. Click to put a tick in Launch Wireless Manager at Windows startup to launch the application at Win- dows Startup. Figure 7 - 36 Settings The Advanced settings allows more detailed configuration. To access the Ad- vanced settings: Access the Wireless Manager program from the Start menu (Start >...
Page 183
Modules & Options Most USIM cards are protected by a Personal Identity Number (PIN). You may turn on or off the Request PIN at startup (click Apply to save any changes). You can PIN Notes also Change PIN (you will need to enter the new PIN in the two fields provided and click Apply to save any changes).
Page 184
Modules & Options Networks The mobile network list lists available networks at your location, and allows you to select a network which to connect. You must disconnect before being able to select Warning a network. Note that some applica- tions automatically Connection...
Modules & Options Text Messaging Service (SMS) In addition to standard internet services you may also send and receive SMS text messages using the Wireless Manager, if your service supports SMS. SMS Utility Access the Wireless Manager application from the Start menu (Start > All Pro- grams >...
Page 186
Modules & Options Messages Click the Messages tab to access the tabs displaying text messages. The tabs at the top of the menu display the Inbox, Drafts, Outbox, Sent and Trash menus. Inbox Drafts Outbox Sent Trash Figure 7 - 40 SMS Utility Messages Text messages are automatically saved to your computer and may be sorted in as-...
Modules & Options Sending a Text Message Access the Wireless Manager application from the Start menu (Start > All Pro- grams > Wireless Manager > Wireless Manager) or the desktop shortcut Click SMS and the SMS Utility will then start. Click the New Message tab.
Page 188
Modules & Options Click Send to send the message or Save to save the message in the Drafts folder. Clicking the Clear icon clears both the Message and To fields. If radio is on then the message will be sent, however if the radio is off the message will be stored in the Outbox.
Page 189
Modules & Options Messages • Opening a text message: Double-click the message and the message will open in a new window (to close it click the close icon in the top right of the message). Figure 7 - 43 Click to close the message Close Message •...
Modules & Options Phonebook The Phonebook allows you to view and edit all your frequently used contacts, and is divided into Contacts and Groups . To access the Phonebook: Access the Wireless Manager application from the Start menu (Start > All Pro- grams >...
Page 191
Modules & Options Contacts • New Contact: Click the New contact button to create a contact. Add the name and at least one phone number (Mobile, Work, Home and Other Import/Export fields are available) for the contact. Click the icon to expand the number Contacts details.
Page 192
Modules & Options Groups You can organize existing contacts into groups from the Groups tab. • New Group: Click the New group button to create a group. Click icon to expand the group details, and click a check box to add at least one phone number from the contacts for the group.
Modules & Options SMS Settings The SMS Utility Settings tab allows you at adjust the SMS features. Figure 7 - 47 SMS Utility Settings SMS Settings Message Length: You can set the number of blocks that can be sent (up to a length of 10 blocks).
Page 194
Modules & Options Send Click Delivery Report to automatically request a reply from a recipient. If you click to Send messages in Outbox automatically upon connection then messages writ- ten when the radio is off, will then be sent automatically the next time radio is turned on.
Page 195
Modules & Options Number You can choose to Use default service center number or you can uncheck the box and add your number manually if your service provider supplies a different number (click Apply to save the change or Default to return to the default number). Memory Phonebook memory status displays the number of contacts displayed on the USIM card.
Modules & Options Sierra Wireless AirCard Watcher With the 3G module and USIM card (supplied by your service provider) installed you may then install the Sierra Wireless AirCard Watcher application. AirCard Wireless Device Watcher allows you to directly access your internet service from the computer. Operation Aboard Aircraft Sierra Wireless AirCard Watcher Installation...
Modules & Options AirCard Watcher Application The connection information is stored on the USIM card supplied by the service pro- vider (where this is not the case you may need to create a profile - see “Profiles” on PIN Number page 7 - 79).
Page 198
Modules & Options The system will connect to your network. The icon will turn green (and the upload/download speeds will be indicated). You can then access the internet, download e-mail etc. as per any internet AirCard Watcher connection. Help Topics To get help on AirCard Watcher configuration...
Page 199
Modules & Options When connected the uplink/downlink speeds will be indicated. You can also click the Speed Graph icon to get a visual display of the uplink/ downlink speeds. 10. While connected you can also click the icon in the notification area of the Roaming taskbar to display the Windows 7 Mobile Broadband connection status.
Page 200
Modules & Options 11. To disconnect from the service provider, click the Disconnect button (note that if you click the close icon at the top right of the screen the application will close however the connection will still be maintained). Online Help 12.
Modules & Options Air Card Watcher Menu Right-click the menu button at the top of the AirCard Watcher screen to bring up the menu, and click to select any item required. Airplane Mode Click on the Airplane Mode icon to turn the ra- dio power off (e.g.
Modules & Options Selecting a Network Operator/Service Provider In most cases all your network operator/service provider details will be stored on your USIM card, and will not need to be edited/modified. If you do need to set up a Network Operator network operator/service provider follow these instructions.
Modules & Options Profiles A profile contains information used to establish a data connection, and this informa- tion is usually stored on the USIM card supplied by your service provider. However you can create, edit or delete profiles if required. Creating a Profile Access the AirCard Watcher application from the Start menu (Start >...
Page 204
Modules & Options You will need to complete the fields for Profile name, Username, Password and Access Point Name (you will need to get the username and password details from your service provider). Edit or Delete Once you have added the details above you can click the Profiles heading menu Profiles and click to select the profile from the Selected Profile dropdown menu and then click OK to set the profile as the default connection.
Modules & Options User Options You can configure User Options as follows. Access the AirCard Watcher application from the Start menu (Start > All Pro- grams > Sierra Wireless > AirCard Watcher) or the desktop shortcut Either click the menu button and select Options, or click the Options button from the main program window.
Page 206
Modules & Options • General - This item allows you to set options for Startup/Shutdown, Warning Messages, Display and Windows support. • Messaging - Set options here for SMS settings. • Network - Configure the network settings from this menu though your fre- quency band information is usually stored on the USIM card.
Modules & Options Text Messaging Service (SMS) In addition to standard internet services you may also send and receive SMS text messages using AirCard Watcher, if your service supports SMS. SMS Express Access the AirCard Watcher application from the Start menu (Start > All Pro- grams >...
Modules & Options Sending a Text Message Access the AirCard Watcher application from the Start menu (Start > All Pro- grams > Sierra Wireless > AirCard Watcher) or the desktop shortcut Sent Messages Either click the menu button and select SMS Express, or click the SMS Express button from the main program window.
Modules & Options Inbox Any received text messages will be displayed in the Inbox. The number of total mes- sages and unread messages will be displayed in the inbox folder title. Messages • Opening a text message: Click on any message in the Inbox to read it in the bottom panel of the window.
Modules & Options Bluetooth & WLAN Combo Module If your purchase option includes the Combination Wireless LAN & V3.0 Blue- Wireless Device tooth module (either Intel® or 3rd Party) then install the driver as instructed from Operation Aboard the appropriate page (see below and see “Bluetooth Settings (Windows 8)”...
Modules & Options 3rd Party Bluetooth (V4.0) Combo Driver Installation Note this driver is required for the 3rd Party combo Bluetooth and WLAN module (Bluetooth V4.0) only. 1. Before installing the driver make sure the Bluetooth module is powered on (use Fn + F12 key combination), then insert the Device Drivers & Utili- ties + User’s Manual disc into the CD/DVD drive.
Modules & Options Intel Bluetooth Combo Driver Installation Note this driver is required only for the Intel combo Bluetooth and WLAN module only. High Speed Bluetooth Data Transfer 1. Before installing the driver make sure the Bluetooth module is powered The Combination Wire- on (use Fn + F12 key combination), then insert the Device Drivers &...
Modules & Options Standard Bluetooth Configuration in Windows 7 Setup your Bluetooth Device so the Computer Can Find it Turn your Bluetooth device (e.g. PDA, mobile phone etc.) on. Add a Device Make the device discoverable (to do this check your device documentation). Click Start, and click Con- trol Panel and then click To Turn the Bluetooth Module On...
Page 214
Modules & Options To Add a Bluetooth Device Access the Bluetooth Devices control panel and click Add a device. Double-click the device you want to pair with the computer. Pairing Options If a device has been pre- viously connected then the pairing option menu will appear when you at- tempt subsequent con-...
Page 215
Modules & Options Enter the code into your Bluetooth enabled device and follow any on-screen instructions to complete the pairing. Figure 7 - 63 Pairing Codes Pairing Code Example The example outlined here shows a connection to a mobile device. Other devices e.g. computers, may have a slightly different connection proce- dure, and may require you to confirm a pairing code is correct on both devices.
Page 216
Modules & Options To Change Settings for the Bluetooth Device Click the notification area icon and select Show Bluetooth Devices. Right-click on the device you want to change and click Properties to: Bluetooth Help • Change the name of the device (click Bluetooth, type a new name and click OK). •...
Modules & Options Intel Rapid Storage Technology Install the Intel Rapid Storage Technology to support your SATA drive if set up in AHCI mode in the BIOS (see “SATA Mode (Advanced Menu)” on page 5 - 10). IRST Driver Installation 1.
Modules & Options Intel® vPro™ Technology Intel® vPro™ Technology is supported by Model B computers only. This set of technology features, built into the computer’s motherboard, allows Information Technology departments remote access to the computer. This allows the IT depart- ment to monitor, maintain and manage computers regardless of the state of the op- erating system or the computer’s power state.
Page 219
Modules & Options Figure 7 - 66 Intel(R) Management Engine (Password Creation) Select MEBx Login and press “Enter” to access the password screen. Enter the pass- word “admin” (without quotes) and you wil then be prompted to enter your own password (note the password information on the prvious page).
Modules & Options ® Intel Management and Security Status (Model B Only) Access the Intel Management and Security Status control panels from the Start ® menu in Windows. These features allow users and IT Administrators to enhance and protect computing assets. Your system administrator will need to assist you in managing some of the information here.
Page 221
Modules & Options General The General tab provides basic information on Intel® AMT, Intel® Standard Man- ageability, Level 3 Manageability Upgrade, Intel® Anti-Theft and Intel® RPAT sta- tus and events. Figure 7 - 68 Intel Management & Security Status General Intel®...
Page 222
Modules & Options Intel® Active Management Technology The Intel® AMT tab will be shown if you system is configured to support it. This allows your network’s IT professionals to remotely discover, heal and protect your computer. Figure 7 - 69 Intel Management &...
Page 223
Modules & Options Intel® Anti-Theft This tab displays information on Intel® Anti-Theft information. Click on the link to connect to an Intel site to get more information on Intel® Anti-Theft technology. Figure 7 - 70 Intel Management & Security Status Intel®...
Page 224
Modules & Options Advanced The Advanced tab provides additional information on the system. Figure 7 - 71 Intel Management & Security Status Advanced For Intel PRO Wireless 2200BG 7 - 100 Intel® Management and Security Status...
Modules & Options Trusted Platform Module The TPM security chip allows you to create and manage digital certificates for user and platform authentication. This type of security is usually administered within large enterprises and organizations, and therefore requires implementation by a sys- tem administrator before users can access security features.
Modules & Options Enabling & Activating TPM Restart the computer. Enter the Aptio Setup Utility pressing F2 during the POST/startup. Use the arrow keys to select the Security menu Select TPM Configuration and press Enter. Select Security Device Support and press Enter, select Enable and press Enter. Select TPM State, press Enter and select Enabled to change the TPM state to enabled.
Page 227
Modules & Options Select Pending operation, press Enter and select the option you require (if you are initializing TPM you should select Enable Take Ownership) and press Enter. You will then need to press F4 to save the changes and restart the computer. Figure 7 - 73 Pending Operation (Enable Take...
Modules & Options Trusted Platform Module (TPM) Driver Installation 1. Make sure you have enabled and activated the TPM in the BIOS before installing the driver (if you do not do see the note below). 2. Insert the Device Drivers & Utilities + User’s Manual disc into the CD/ DVD drive.
Modules & Options Initializing TPM Run the application from the Infineon Security Platform Solution > Manage Security Platform item in the Start > All Programs menu. Click User Settings (tab) and click Yes, or right-click the icon in the notification area of the taskbar, and select Security Platform Initialization (or click the Security Platform State taskbar bubble).
Page 230
Modules & Options Choose the Security Platform Features you want to use by clicking the appropriate tickbox. Enter a Basic User Password (and re-type to confirm it) and click Next. Figure 7 - 75 Settings Help Right-click the icon the notification area of the taskbar to bring up the menu to select Help or How to use...
Modules & Options Infineon Security Platform Settings Tool The Infineon Security Platform Settings Tool allows you to manage and check the TPM state, manage your password information, and to backup and restore the TPM Menus data. As TPM is usually administered within large enterprises and organizations, Note that not all the your system administrator will need to assist you in managing the information here.
Page 232
Modules & Options User Settings This page allows the settings to be configured for the currently logged in Infineon Security Platform user including the ability to change the password, configure se- cure e-mail, file and folder encryption and Enhanced Authentication. You can also import or delete certificates protected by the security platform.
Page 233
Modules & Options Backup Here you can configure backup and restore operations. Backup files contain the computer identification and user identification information which is used to match the machine name and user name with the current machine and user during restora- tion.
Page 234
Modules & Options Migration The Migration tab is used to help securely transfer keys and certificates from one platform to another. Figure 7 - 79 Infineon Security Platform Settings Tool (Migration) 7 - 110 Trusted Platform Module...
Page 235
Modules & Options Password Reset Use Password Reset to reset basic user passwords when required. Figure 7 - 80 Infineon Security Platform Settings Tool (Password Reset) Trusted Platform Module 7 - 111...
Page 236
Modules & Options BitLocker BitLocker Drive Encryption can be used in conjunction with the TPM to encrypt data on the disk and is done via the Microsoft BitLocker Control Panel Applet. Click Configure and select a drive to be encrypted and then follow the Wizard to begin the encryption process.
Page 237
Modules & Options Access the Microsoft BitLocker Drive Encryption control panel applet from the Windows control panel (System and Security). Figure 7 - 82 BitLocker Drive Encryption Trusted Platform Module 7 - 113...
Page 238
Modules & Options Advanced Configure all the Security Platform owner and policy settings from the Advanced tab. The settings that can be changed are for the local computer only. Figure 7 - 83 Infineon Security Platform Settings Tool (Advanced) 7 - 114 Trusted Platform Module...
Modules & Options Intel® Smart Connect Technology Intel® Smart Connect Technology periodically, and briefly, wakes the computer Intel® Smart Connect from Sleep mode in order to update information for certain applications (e.g. to get Technology System mail from Microsoft Outlook) as required. These updates can therefore be made Requirements without having to turn the computer on, and applications will be up to date when the Note that in order to sup-...
Modules & Options Intel® Smart Connect Technology Configuration Access the Intel(R) Smart Connect Technology application from the Start menu. Click Basic (tab) and adjust the slider to set the update frequency (note that the Wireless Device slider balances between “More Frequent Updates” and “More Battery Life”). Operation Aboard Note the sidebar warning about the use of Intel(R) Smart Connect Technology Aircraft...
Page 241
Modules & Options Click Advanced (tab) to access the Extended Power Savings settings. Extended Power Savings allows you to set a time period during which the computer will update less often (e.g. at night while you are asleep or whenever you are at work).
Page 242
Modules & Options Click the Help tab and click Topics to access the main Help menu. Intel WLAN Modules If your purchase option includes an Intel WLAN module, (with Intel’s PROSet Wireless Con- nection Utility stalled), Intel® Smart Connect Technology will search for WiFi net- works around you that...
Modules & Options Intel Wireless Display Application ® The Intel ® Wireless Display Application (requires Intel® Centrino WLAN/ Compatible Combo module), in conjunction with a compatible video adapter (purchased sep- Adapters arately), allows you to display the contents of the notebook display on another dis- play (e.g.
Modules & Options Intel WiDi Application Configuration ® Click Start > All Programs > Intel Corporation > Intel(R) Wireless Display > Intel(R) Wireless Display, or double click the icon on the desktop. Click I agree to the terms of this license (button). The application will scan for any connected compatible adapters (or you can click the Scan for available adapters button to enable Intel My WiFi Technology).
Page 246
Modules & Options Click to select and detected adapters, and click Connect. The system will then prompt you to enter the 4-digit security code which will be displayed on the external TV Screen (or press the connect button on the wireless speaker adapter).
Page 247
Modules & Options You will then be prompted to enter a name for the video adapter and click Continue. Click Finished to complete the setup. Test Audio Adapter To verify a successful audio connection (for In- tel® Wireless Music), select the “Test your audio connection”...
Troubleshooting Chapter 8: Troubleshooting Overview Should you have any problems with your computer, before consulting your service representative, you may want to try to solve the problem yourself. This chapter lists some common problems and their possible solutions. This can’t anticipate every problem, but you should check here before you panic. If you don’t find the answer in these pages, make sure you have followed the instructions carefully and observed the safety precautions in the preface.
Troubleshooting Basic Hints and Tips Many of the following may seem obvious but they are often the solution to a problem when your computer ap- pears not to be working. • Power - Is the computer actually plugged into a working electrical outlet? If plugged into a power strip, make sure it is actually working.
Troubleshooting Backup and General Maintenance • Always backup your important data, and keep copies of your OS and programs safe, but close to hand. Don’t forget to note the serial numbers if you are storing them out of their original cases, e.g. in a CD wal- let.
Troubleshooting Viruses • Install an Anti-Virus program and keep the definitions file (the file which tells your program which viruses to look for) up to date. New computer viruses are discovered daily, and some of them may seriously harm your computer and cause you to lose data. Anti-Virus programs are commercially available and the defini- tions file updates are usually downloadable directly from the internet.
Troubleshooting Upgrading and Adding New Hardware/Software • Do not be tempted to make changes to your Windows Registry unless you are very sure of what you are doing, otherwise you will risk severely damaging your system. • Don’t open your computer or undertake any repair or upgrade work if you are not comfortable with what you are doing.
Page 254
Troubleshooting • Thoroughly check any recent changes you made to your system as these changes may affect one or more system components, or software programs. If possible, go back and undo the change you just made and see if the problem still occurs. •...
Troubleshooting Problems and Possible Solutions Problem Possible Cause - Solution You turned on the power but it doesn’t Battery missing / incorrectly installed. Check the battery bay, make sure the work. battery is present and seated properly (the design of the battery only allows it to go in one way).
Page 256
Troubleshooting Problem Possible Cause - Solution The computer feels too hot. Make sure the computer is properly ventilated and the Vent/Fan intakes are not blocked. If this doesn’t cool it down, put the system into Hibernate mode or turn it off for an hour. Make sure the computer isn’t sitting on a thermal surface (see “Overheating”...
Page 257
Troubleshooting Problem Possible Cause - Solution You forget the boot password. If you forget the password, you may have to discharge the battery of the CMOS. Contact your service representative for help. Password Warning If you choose to set a boot password, NEVER forget your password. The consequences of this could be serious. If you cannot remember your boot password you must contact your vendor and you may lose all of the information on your hard disk.
Page 258
Troubleshooting Problem Possible Cause - Solution The system freezes or the screen goes The system’s power saving features have timed-out. Use the AC/DC adapter, dark. press the sleep (Fn + F4) key combination, or press the power button if no LEDs are lit.
Page 259
Troubleshooting Problem Possible Cause - Solution A file cannot be copied to/from a The transfer of data between the computer and a Bluetooth enabled device is connected Bluetooth device. supported in one direction only (simultaneous data transfer is not supported). If you are copying a file from your computer to a Bluetooth enabled device, you will not be able to copy a file from the device to your computer until the file transfer process from the computer has been completed.
Page 260
Troubleshooting Problem Possible Cause - Solution I previously turned off the WLAN module The computer entered a power saving state with the WLAN Switch in the ON using the Fn + F11 key combination (or position, and upon resuming from the power saving state the WLAN module Windows Mobility Center button), but turned ON.
Troubleshooting Bluetooth Connection Problems If you are experiencing problems connecting to some Bluetooth devices (in particular certain mobile phones and headsets) it maybe necessary to download and install the Windows Mobile Device Center software (for Win- dows Vista and Windows 7). Go to the Microsoft website and search for the Microsoft Windows Device Center Driver for Windows Vista (64-bit or 32-bit) and Windows 7 (64-bit or 32-bit), and then download the driver.
Page 262
Troubleshooting Right-click Bluetooth Peripheral Device and click on Update Driver Software. Click Browse my computer for driver software. Click Let Me pick from a list of device drivers on my computer. Figure 8 - 2 - Browse my computer.../Let me pick from... Select Bluetooth Radios from the list.
Page 263
Troubleshooting 10. A list of drivers will appear with Manufacturer on one side and Model in the other. 11. Choose Microsoft Corporation (make sure you choose the full name Microsoft Corporation and do not choose Microsoft - Note that you must have installed the Microsoft Windows Device Center Driver for Microsoft Corporation to appear in the list).
Page 264
Troubleshooting 15. The Device Manager should now display the Windows Mobile-based device support under Bluetooth Radios. 16. You will need to repeat the process for any other Bluetooth Peripheral Devices listed under Other Devices. Figure 8 - 5 - Device Manager - Bluetooth Radio 8 - 16 Bluetooth Connection Problems...
Interface (Ports & Jacks) Appendix A: Interface (Ports & Jacks) Overview The following chapter will give a quick description of the interface (ports & jacks) which allow your computer to communicate with external devices, connect to the internet etc. USB Port / Card Reader / ExpressCard Power Note that power to the USB ports, card reader and ExpressCard may be enabled/disabled in the BIOS (see page Interface (Ports &...
Interface (Ports & Jacks) Notebook Ports and Jacks Item Description Card Reader Port The card reader allows you to use some of the latest digital storage cards. Push the card into the slot and it will appear as a removable device. DC-In Jack Plug the supplied AC/DC adapter into this jack to power your computer.
Page 267
Interface (Ports & Jacks) Item Description Headphone-Out Jack Headphones or speakers may be connected through this jack. Note: Set your system’s volume to a reduced level before connecting to this jack. Microphone-In Jack Plug an external microphone in to this jack to record on your computer. RJ-45 LAN Jack This port supports LAN (Network) functions.
Page 268
Interface (Ports & Jacks) Item Description USB 2.0/1.1 Ports*/USB These USB 2.0 compatible ports (USB 2.0 is fully USB 1.1 compliant) are for low-speed 3.0 Ports peripherals such as keyboards, mice or scanners, and for high-speed peripherals such as external HDDs, digital video cameras or high-speed scanners etc. Devices can be plugged into the computer, and unplugged from the computer, without the need to turn the system off (if the power rating of your USB device is 500mA or above, make sure you use the power supply which comes with the device).
Control Center Appendix B: Control Center Overview The following chapter will give a quick description of the functions of the Control Center. The Control Center gives quick access to frequently used controls, power management features and enables you to quickly turn mod- ules on/off.
Page 270
Control Center Power Modes You can set a Power Mode by clicking the appropriate icon at the top of the Control Center. Each power mode will affect the power status of modules (e.g. WLAN, Bluetooth, 3G or Camera), screen brightness, TouchPad power and Silent Mode.
Page 271
Control Center Flight User Modes Power Saving Entertainment Quiet Performance (Win 7 Only) Defined Icon Power Plan Power Saver Balanced Power Saving Power Saving High Performance Power Conservation Mode Energy Star BIOS Default Energy Star Energy Star Performance Brightness WLAN (Win 7 Only) Bluetooth BIOS Default...
Page 272
Control Center Power Status The Power Status icon will show whether you are currently powered by the battery, or by the AC/DC adapter plugged in to a working power outlet. The power status bar will show the current battery charge state. Brightness The Brightness icon will show the current screen brightness level.
Page 273
Control Center Sleep Click the Sleep button to bring up the Hibernate or Sleep buttons, and click either button to have the computer enter the appropriate power-saving mode (see “Power-Saving States” on page 3 - Display Switch Click the Display Switch button to access the menu (or use the + P key combination) and select the appro- priate attached display mode (see page 10).
Page 274
Control Center Caps Lock/Scroll Lock/ Number Lock Click the button to toggle the appropriate lock mode. B - 6 Control Center...
Video Driver Controls Appendix C: Video Driver Controls The basic settings for configuring the LCD are outlined in “Video Features” on Video Card Options page 1 - Note that card types, specifications and driv- Video Driver Installation ers are subject to contin- updates Make sure you install the drivers in the order indicated in Table 4 - 1, on page 4 -...
Video Driver Controls Intel Graphics & Media Control Panel ® Advanced video configuration options are provided by the Intel Graphics and ® Application Mode Media Control Panel. To access the control panel: Note that all figures pic- Click Advanced settings in the Screen Resolution control panel in Windows. tured, and instructions Click the Intel(R)...
Page 277
Video Driver Controls You may make changes to any of the graphics properties by clicking the appropriate menu tab on the left of the menu and adjusting the settings on the right. Options & Support Click Options & Sup- port and select an item from the sub-menu to bring up the help and...
Video Driver Controls Display Devices & Options Besides the built-in LCD you can also use an external monitor/flat panel display/TV connected to the external monitor port or to the HDMI-Out port (High-Definition Function Key Combination Multimedia Interface) as your display device. The table below outlines the display options.
Video Driver Controls Attaching Other Displays If you prefer to use a monitor or flat panel display, connect it to the external monitor Multiple Display port or HDMI-Out port on the left of the computer. At least one other dis- To Clone Displays: play must be attached in Attach your display to the external monitor port or HDMI-Out port, and turn it on.
Page 280
Video Driver Controls To Enable Extended Desktop: Attach your display to the external monitor port or HDMI-Out port, and turn it on. Go to the Intel(R) G&M control panel and click Display > Multiple Displays. Display Settings Click Operating Mode and select Extended Desktop from the menu. Extended Desktop Click Apply, and OK to confirm the settings change.
Page 281
Video Driver Controls Display Profiles You can save display settings to be loaded at any time. Go to the Intel(R) G&M control panel and click Display. Configure the General Settings, Multiple Displays, Color Enhancement, Custom Resolution & Monitor/TV Settings to your preferences. Click Apply, and OK to confirm the settings change.
Video Driver Controls Configuring an External Display in Windows 7 You can also use the Screen Resolution control panel in Windows 7 to configure an Function Key external display. Combination Attach your display to the external monitor port or HDMI-Out port, and turn it on. You can use the Fn + Go to the Screen resolution control panel (see “Video Features”...
Page 283
Video Driver Controls You can configure the displays from the Multiple Displays menu. Figure C - 7 Screen Resolution Multiple Display Options (Win 7) • Duplicate these displays - Shows an exact copy of the main display desktop on the other display(s) •...
Page 284
Video Driver Controls Using the Windows Logo Key + P Key Combination to Switch Displays You can also use the + P key combination to quickly change display configura- tion and modes (this is particularly useful when attaching a projector) in Windows 7. Attach your display to the external monitor port or HDMI-Out port, and turn it on.
Video Driver Controls HDMI Audio Configuration HDMI (High-Definition Multimedia Interface) carries both audio and video signals. Volume Indicator In some cases it will be necessary to go to the Sound control panel and manually configure the HDMI audio output as per the instructions below. Click the taskbar volume indicator when an...
Page 286
Video Driver Controls Double-click the connected HDMI device (or right-click and select Properties) to adjust the HDMI settings from the control panel tabs. Click OK to close the control panel (see notes overleaf). Figure C - 10 HDMI Device Properties C - 12 HDMI Audio Configuration...
Page 287
Video Driver Controls HDMI Notes • Connect a device with HDMI support to the HDMI-Out port BEFORE attempt- ing to play audio/video sources through the device. Other Applications • To play audio sources through your external display’s (TV or LCD) speakers If you are using a third you will need to go to the audio configuration control panel on the display and party...
Specifications Appendix D: Specifications Latest Specification Information The specifications listed in this Appendix are correct at the time of going to press. Certain items (particularly processor types/ speeds and CD/DVD device types) may be changed, updated or delayed due to the manufacturer's release schedule. Check with your service center for details.
Specifications Memory Storage Slot Dual Channel DDRIII (DDR3) One Changeable 2.5" / 9.5 mm (h) HDD Two Mini-Card Slots: with SATA (Serial) Interface Two 204 Pin SO-DIMM sockets Slot 1 for Half Size Mini-Card WLAN supporting DDR3 1333MHz/1600MHz Module with PCIe & USB Interfaces Audio (real operational frequency depends on Slot 2 for Full Size 3G Module with USB...
Specifications Communication 3rd Party Combo WLAN (802.11b/g/n) Power and Bluetooth v4.0+LE Half Mini-Card 56K Fax Modem with V.90 & V.92 Compliant Full Range AC/DC Adapter Module with PCIe Interface (Factory AC input 100 - 240V, 50 - 60Hz, Option) Built-In Intel® 10/100/1000Mb Base-TX DC Output 19V, 3.42A or 18.5V, 3.5A (65 Ethernet LAN 3rd Party WLAN 802.11b/g/n Half Mini-...
Specifications Design Features All USB / e-SATA / Card Reader ports/ slots can be switched on/off in the BIOS WLAN Slide Switch Painted Style Finish Supports Intel® Anti-Theft Technology Supports Intel® Smart Connect Technology Supports Intel® Small Business Advantage Environmental Spec Temperature °...
Docking Station Guide Appendix E: Docking Station Guide Overview The docking station provides your computer with an easy connectable desktop environment when portability is not required. This allows for easy connections to external displays, USB devices (with a full range of extra USB ports), audio devices and provides a battery charging facility.
Docking Station Guide Computer and Docking Station The computer may hot or cold dock/undock with the docking station, i.e. the computer may be powered on (hot docking/undocking) or powered off (cold docking/undocking) when docking or undocking. However if you in- tend to hot dock/undock the system then make sure that the hot key driver, provided on the computer’s Device Drivers &...
Docking Station Guide System Map: Front View Figure E - 1 System Map Front Power Button LED Backup Button (if a Hard Disk is installed in the Device Bay) Lock Switch Notebook Eject Latch Notebook Placeholder Retaining Pins Docking Connector Eject Pins ...
Docking Station Guide System Map: Rear View Figure E - 2 System Map Rear Security Lock Slot USB 3.0 Port DVI-D Out Port HDMI-Out Port External Monitor Port RS232 (Serial) COM Port RJ-45 LAN Jack DC-In Jack Headphone Jack 10. Microphone Jack 11.
Docking Station Guide Power Button LED & Lock Switch LED Indicator Icon Color Description Orange DC Power is Plugged In and the Computer is Off or in Hibernate Mode* Green The Docking Station is On or in Sleep Mode Table E - 1 - Power Button LED & Lock Switch LED Indicator *To confirm the computer’s power status check the LED Power Indicators on the computer itself.
Docking Station Guide System Map: Left & Right Views Figure E - 3 System Map Left & Right Views Bay with HDD or Dummy Caddy Bay with Optical Device Drive (DVD) Powered USB 3.0 Port USB 3.0 Ports USB Port Power Note that power to the notebook computer and docking station’s USB ports may be enabled/ disabled in the notebook computer’s BIOS settings (see the BIOS guide in Chapter 5 of the notebook’s user manual).
Docking Station Guide Cold Docking the Computer to the Docking Station Remove all packing materials and place the docking station on a stable surface. Securely attach any peripherals you want to use with the docking station (e.g. keyboard and mouse) to their ports.
Page 302
Docking Station Guide Make sure the computer’s hot key driver is installed (especially if you intend to hot dock the system). Remove the AC/DC adapter from the notebook computer and then close the computer’s lid/LCD and turn it over (if you are using the optional 9 cell battery make sure you remove the battery before attempting to dock the computer with the docking station).
Page 303
Docking Station Guide Make sure that the notebook computer’s AC/DC adapter is NOT ATTACHED to the computer’s DC-In jack and that the computer is OFF. Ensure that the lock switch on the docking station is in the unlock position. 10. Press the computer down onto the docking station so that the docking connectors line up. 11.
Docking Station Guide Cold Undocking the Computer from the Docking Station Shut the computer down as per the normal Windows shutdown (select Shut Down from the Start menu in Windows 7) procedure (the Power LED on the docking station will be orange). Slide the lock switch on the docking station in to the unlock position.
Docking Station Guide Hot Docking the Computer to the Docking Station Remove all packing materials and place the docking station on a stable surface. Securely attach any peripherals you want to use with the docking station (e.g. keyboard and mouse) to their ports.
Page 306
Docking Station Guide Make sure the computer’s hot key driver is installed for hot docking/undocking the system. The computer should be on, however remove the AC/DC adapter from the notebook computer and then close the computer’s lid/LCD and turn it over (if you are using the optional 9 cell battery you cannot hot dock the computer with the docking station).
Page 307
Docking Station Guide Ensure that the lock switch on the docking station is in the unlock position. Press the computer down onto the docking station so that the docking connectors line up (the Power LED on the docking station will be orange). 10.
Docking Station Guide Hot Undocking the Computer from the Docking Station Hot undocking using Windows: When the system is docked click the the icon in the taskbar notification area and click Safely Remove Hardware and Eject Media (Figure E - 11) from the menu.
Page 309
Docking Station Guide Hot undocking using the Control Center: Make sure the computer’s hot key driver is installed for hot docking/undocking the system. Press the Fn + Esc key combination to run the Control Center. Click the docking icon in the Control Center (the icon displays the current docking status). The docking icon will change to the undock icon to display the current status and the Undock Complete message will appear in the notification area of the taskbar (see over).
Page 310
Docking Station Guide Press the Fn + Esc key combination to run the Control Center. The docking power LED will be Orange at this point and the ports, buttons and attached devices on the docking station will not work. If you do not wish to separate the notebook and docking station at this point you can click the icon in the Control Center to redock the system.
Docking Station Guide Power Button Configuration To prevent your computer from entering a power-saving state if you choose to work with the lid/LCD closed, then it may be necessary to redefine what the computer is set to do if the lid/LCD is closed when plugged in. Click Start, and click Control Panel (or point to Settings and click Control Panel).
Docking Station Guide Docking Station Ports & Jacks The following will give a quick description of the interface (ports & jacks) which allow your docking station and computer to communicate with external devices, connect to the internet etc. When the notebook is docked to the docking station all the ports on the docking station will function, however only some of the ports on the notebook will function (see the note alongside each item for specific information)..
Page 313
Docking Station Guide Item Description Note External Monitor (VGA) This port allows you to connect an external monitor, or Flat Panel Use only the external monitor Port Display, to get dual video or simultaneous display on the LCD port on the docking station and external monitor/FPD.
Page 314
Docking Station Guide Item Description Note Security Lock Slot To prevent possible theft, a Kensington-type lock can be attached to this slot. Locks can be purchased at any computer store. S/PDIF-Out Jack This S/PDIF (Sony/Philips Digital Interface Format) Out Port allows you to connect your DVD-capable PC to a Dolby AC-3 compatible receiver for “5.1”...
Docking Station Guide Multiple Displays Any two of the following displays may be enabled simultaneously when the system is docked. You can toggle through the display options by using the Fn + F7 key combination (make sure any attached displays are powered on).
Docking Station Guide One Button Hard Disk Backup When the system is docked you can press the Hard Disk Backup Button ( Figure E - 14) to launch the Win- dows 7’s Backup and Restore function. If you do not have a hard disk installed in the docking station you can set the Windows 7’s Backup and Restore application to backup to any attached hard disk, CD/DVD or non system partition of your computer.
Docking Station Guide Hard Disk Backup Procedure Press the hard disk backup button. Windows 7’s Backup and Restore application will be launched. If you are on the first run of the program click “Set up backup”, or “Back up now” thereafter. Figure E - 15 - Back Up Now / Set Up Backup One Button Hard Disk Backup E - 23...
Page 318
Docking Station Guide You can then select where you want to save the backup (click the storage media required and click Next). You can then select what you want to backup on a regular schedule (you can let Windows choose or select files and folders yourself).
Page 319
Docking Station Guide You can review the backup settings before running the backup. Click the Change schedule button to change the time the backup is run. Click “Save Settings and run backup” to begin the backup process. Figure E - 17 - Backup Schedule & Progress One Button Hard Disk Backup E - 25...
Docking Station Guide Hard Disk Restore Procedure Press the hard disk backup button. Windows 7’s Backup and Restore application will be launched. Click “Restore my files”. Figure E - 18 - Restore My Files E - 26 One Button Hard Disk Backup...
Page 321
Docking Station Guide You can browse any attached devices for files or folders to restore (or click “Choose a different date” to choose a restore file/folder from different date). Click Next and choose the original location, or choose a new location and then click Restore (Windows may prompt you if you need to replace any files).
Page 322
Docking Station Guide If your computer has had a problem and you need to recover your computer to an earlier point you can click “Recover system settings or your computer” (see Figure E - 18 on page E - 26). Click “Open System Restore.”...
Docking Station Guide Specifications Power Full Range AC/DC 90W Adapter Storage AC input 100 - 240V, 50 - 60Hz, DC Output 19V, 4.74A One Changeable 12.7mm(H) Super Multi ODD / Blu-ray Combo Security ODD or 2.5" / 9.5 mm(H) HDD Caddy with SATA (Serial) Interface (Factory Option) Security (Kensington®...
Windows 8 Appendix F: Windows 8 Overview This Appendix contains information (including control panel information, driver installation etc.) for users of the Windows 8 OS. You can refer to the main manual for details of drivers required, audio & video information, BIOS, modules etc. However any information specific to Windows 8 will be included in this Appendix, as well as details on how to navigate the Windows 8 Metro User Interface to access the applications, control panels, taskbar etc.
Windows 8 Windows 8 Start Screen & Desktop The Apps, control panels, utilities and programs within Windows 8 are accessed from the Metro user interface’s Start screen and/or Windows Desktop. The Desktop (which runs as an app within the Start screen) can be ac- cessed from the Desktop item in the Start screen (or by using the Windows Logo Key + D key combination).
Windows 8 Apps & Tiles The Windows 8 Start screen will contain a number of Apps, and many more will be installed as you add more applications etc. Not all of these apps can fit on one screen so you will often need use the slider at the bottom of the screen in order to view all the necessary apps.
Windows 8 Desktop Application When the Desktop app is running (click the app in the Start screen or use the Windows Logo Key + D key combination) you can use lower left hot corner to switch between the Start screen and the Windows Desktop. To do so move your mouse to hover over the bottom left corner of the screen and click the pop-up.
Page 329
Windows 8 When the Desktop app is running you can right-click the lower left hot corner (or use the Windows Logo Key + X key combination) to bring up an advanced context menu of useful features such as Control Panel, Programs and Features, Power Op- Display Most tions, Task Manager, Search, Windows Explorer, Command Prompt, Device Man- Recently Used...
Windows 8 Windows 8 Charms Bar The right side of the screen displays the Windows 8 Charms Bar. The Charms Bar contains the Search, Share, Start, Devices and Settings menus. To access up the Charms Bar move the cursor to the upper or lower right corners of the screen, and then hover over one of the items in the Charms Bar to activate it (the bar will be black when it is active), or use the Windows Logo Key + C key combination.
Windows 8 Charms Bar Items • Search : You can search for any file, application, apps and control panel settings with instantaneous results. • Share : This button is used to share information with people via mail or social networks. •...
Windows 8 Windows 8 Control Panel In many instances throughout this manual you will see an instruction to open the Control Panel. The Control Panel is much the same as that in Windows 7, however it can be accessed in a number of ways in Windows 8. •...
Page 333
Windows 8 • When in the Desktop app (this does not apply to the Start screen) click on Settings in the Windows Charms Bar and select Control Panel from the menu. Figure F - 9 - Settings Charms Bar (Desktop App Only) •...
Page 334
Windows 8 • Right-click the lower left hot corner to bring up the menu and select Control Panel (see Figure F - 4 on page F - Keyboard Shortcut to Control Panel You can also use keyboard shortcuts to access the Control Panel. Press the Windows logo key and X to bring up the context menu, and then press P to bring up the Control Panel.
Windows 8 Windows 8 Taskbar In many instances throughout this manual you will see an instruction to access the notification area of the task- bar. In Windows 8 the taskbar is accessed from the Desktop application. If you are in the Start screen you will need to click the Desktop app to switch to the Desktop.
Windows 8 LED Indicators The LED indicators on the computer display helpful information about the current status of the computer. Icon Color Description Icon Color Description DC Power is Plugged Orange Blue Power Button The Powered USB Port Green Hard Disk Activity is On* (System Off) Blinking Orange...
Windows 8 Keyboard - Windows 8 The main difference between the Windows 7 & Windows 8 keyboards is in the func- Windows Logo tion of the Windows Logo Key & Menu/Application Key (in the Start screen), oth- Keyboard Shortcut erwise the keyboard functions are identical (see “Keyboard”...
Windows 8 Keyboard Shortcuts The following Windows Logo Key (Winkey) keyboard shortcuts are useful for navigation/operation in Windows 8. Description Windows Logo Key + Tap Winkey Toggle between the Start screen and the foremost running app or the Windows Desktop Display Charms menu Switch to the Windows Desktop and toggle show Desktop Switch to the Windows desktop and launch Windows Explorer with Computer displayed...
Windows 8 Function/Hot Key Indicators & Control Center The function/hot key indicators and Control Center function in the same manner as outlined for Windows 7 on “Function/Hot Key Indicators” on page 1 - 9 “Control Center” on page 1 - 10.
Windows 8 Video Features You can switch display devices, and configure display options, from the Display control panel (in Appearances and Personalization) in Windows 8 in the same manner as Windows 7 running the Desktop app (see “Desktop Application” on page F - 4 Appendix C).
Windows 8 Power Options Power Options can be accessed from the Control Panel in the same manner as Windows 7 from the Desktop app. The Power item in Settings in the Charms Bar in Windows 8 may be used to Shut down, Restart or send the computer to Sleep.
Windows 8 Ctrl + Alt + Delete Key Combination You can use the CTRL + ALT + DEL key combination from almost any of the Windows 8 interfaces/apps to bring up a full-screen displaying Lock, Switch User, Log off, Change a password and Task Manager options. If you click the Power icon in the lower right corner of the screen a power management option menu appears to display Sleep, Shut down, and Restart.
Windows 8 Wake On LAN Settings If you require your computer to wake up from network activity in Windows 8 then make sure that the computer is either in Sleep or Hibernate. The power/sleep button Wake On LAN (Fn + F4 key combo) and closed lid may be set to send the computer in to a power- Support saving state.
Windows 8 Running Metro UI Apps To run Apps in the Metro UI in Windows 8 you will need to check that the Screen Screen Resolution Resolution and User Account Control Settings are compatible with the system re- for Metro Style Apps quirements: (Windows 8) Screen Resolution Settings...
Windows 8 User Account Control Settings If your computer meets the minimum screen resolution requirements, and still you can't run Metro Apps, then that you have to check the status of User Account Control (UAC). Metro Apps may fail to open when the UAC is turned off.
Windows 8 Drivers & Utilities Make sure you install all the drivers and uti lites for your system. Follow the instructions in Chapter 4 “Drivers & Utilities” on page 4 - 1/“Modules & Options” on page 7 - 1 for installing all the basic system drivers and module drivers for Windows 7 &...
Windows 8 Driver Installation (Windows 8) Insert the Device Drivers & Utilities + User’s Manual disc into the computer’s DVD drive. Click the message “Tap to choose what happens with this disc.” Click Run autorun.exe. Driver Installation If you miss the message above you can eject the De- vice Drivers &...
Page 348
Windows 8 Win 7 SP1/Win 8 Driver Page # Win 7 SP1/Win 8 Driver Page # Chipset Page 4 - 6 PC Camera Module (see page Page 7 - 3 Video (VGA) Page 4 - 6 Wireless LAN Module (see page Page 7 - 11 Page 4 - 6 Fingerprint Reader Module...
Windows 8 PC Camera (Windows 8) Use the Fn + F10 key combination (see “Function/Hot Key Indicators” on page 1 - 9) or Control Center but- ton to toggle power to the PC Camera module. Install the driver as instructed in “PC Camera Driver Installation”...
Windows 8 Metro UI Camera App Make sure the PC Camera is turned on by using the Fn + F10 key combination (or Control Center button). Run the Camera App from the Metro UI by clicking on the Camera App icon The camera interface is a translucent app bar with three buttons.
Page 351
Windows 8 You can also click on More to adjust Brightness, Contrast and Flicker (if you find that the video screen in the camera program is flickering, you can try to adjust the setting here), Figure F - 23 -More Camera Options •...
Windows 8 Taking Pictures/Capturing Video Make sure the PC Camera is turned on by using the Fn + F10 key combination (or Control Center button). Run the Camera App from the Metro UI by clicking on the Camera App icon Click to select the timer if you require a countdown before capture.
Page 353
Windows 8 A scroll arrow will appear on the left side of the screen after any pictures/videos have been captured. Click the arrows (on either side of the screen) to browse through the captured photos/video, and back to the Camera App. 10.
Windows 8 Wireless LAN Settings (Windows 8) If you have included an Intel® or 3rd Party Wireless LAN (or WLAN & Bluetooth combo) module in your pur- chase option, make sure that the WLAN module is on before installing the driver. Use the Fn + F11 key combination (see “Function/Hot Key Indicators”...
Windows 8 WLAN Configuration in Windows 8 You can configure a wireless connection using one of the following options, however make sure the Wireless LAN module is turned on (and not in Airplane Mode) before configuration begins. Charms Bar Go to the Start screen and select Devices in the Charms Bar. Select Settings and then click the WiFi icon (it should read Available under the icon and Airplane mode should be Off).
Page 356
Windows 8 Double-click an access point to connect to it (or click it and click Connect). Enter a network security key (password) if required, and click Next. You can choose to share or connect to devices or not. When you are connected to the network access point it will display the Connected icon Select any connected network and click Disconnect to disconnect from a connected access point.
Page 357
Windows 8 11. You need to either use Airplane Mode, or to turn the WLAN module off aboard aircraft. Wireless Device Operation Aboard Aircraft The use of any portable electronic transmission devices aboard aircraft is usually prohibited. Make sure the module is either OFF or in Air- plane Mode (for Win- dows 8 only) if you are...
Windows 8 Desktop Mode Switch to the Windows Desktop (click the App or use the Windows logo key + D key combination). Click the wireless icon in the notification area of the taskbar. A list of available access points will appear. Double-click an access point to connect to it (or click it and click Connect).
Windows 8 Control Panel If you are in Category View do the following (see over for Icon View): Open the Control Panel (see “Windows 8 Control Panel” on page F - Click the Network and Internet control panel. Click Connect to a network. Figure F - 31 - Network and Internet Control Panel A list of available access points will appear.
Page 360
Windows 8 If you are in Icon View do the following: Open the Control Panel (see “Windows 8 Control Panel” on page F - Click Network and Sharing Center. Click Change Adapter Settings. Double-click Wi-Fi. Figure F - 32 - Network and Sharing Center Control Panel A list of available access points will appear.
Windows 8 3G Settings (Windows 8) If you have included an optional UMTS/HSPDA OR UMTS/HSPDA+ based 3G Module (Universal Mobile Telecommunications System or High Speed Packet Access) module (see “Communication” on page D - 4 specification details) in your purchase option, you do not require a driver/application installation for Windows 8.
Windows 8 3G Configuration in Windows 8 You can configure a 3G connection as below, however make sure the 3G module is turned on by pressing the Fn + key combination (give the module about 10 seconds to power on) or Control Center button (and not in Airplane Mode) before configuration begins.
Page 363
Windows 8 Any 3G service provider (connection information is usually stored on the USIM card) will appear under Mobile Broadband. Double-click any connection icon under Mobile Broadband (or click and click Connect). Figure F - 34 - Mobile Broadband (Connect) The system will connect to your network.
Page 364
Windows 8 You can then access the internet, download e-mail etc. as per any internet connection. To disconnect you can select the connection and click Disconnect 10. You need to either use Airplane Mode, or to turn the Mobile Broadband module off aboard aircraft. ...
Windows 8 Bluetooth Settings (Windows 8) If your purchase option includes the Combination Wireless LAN & Bluetooth module (either Intel® or 3rd Party) then install the driver as instructed in Chapter 7 (see links below). Use the Fn + F12 key combination or Control Center button to toggle power to the Bluetooth module. ...
Windows 8 Bluetooth Configuration in Windows 8 You can configure a Bluetooth connection as below, however make sure the Bluetooth module is turned on (and not in Airplane Mode) before configuration begins. Desktop Mode Switch to the Windows Desktop (click the App or use the Windows logo key + D key combination).
Page 367
Windows 8 Click Add a Device. Double-click the device you want to pair with the computer. Figure F - 38 - PC Settings (Devices) - Add A Device On first connection the computer will provide you with a pairing code to be entered onto the device. Figure F - 39 - Enter the Passcode Enter the code into your Bluetooth enabled device and click Yes on the computer to complete the pairing.
Page 368
Windows 8 You need to either use Airplane Mode, or to turn the Bluetooth module off aboard aircraft. Wireless Device Operation Aboard Aircraft The use of any portable electronic transmission devices aboard aircraft is usually prohibited. Make sure the module is either OFF or in Air- plane Mode (for Win- dows 8 only) if you are...
Page 369
Windows 8 To Make your Computer Discoverable to Bluetooth Devices Switch to the Windows Desktop (click the App or use the Windows logo key + D key combination). Click the notification area of the taskbar, click the Bluetooth icon and click Open Settings. Click Options, and make sure that Allow Bluetooth devices to find this computer check box (Discovery) has a tick inside it.