Page 1
PORTI-SP MODEL (Panel Printer) Rev. 2.0 WOOSIM SYSTEMS Inc. #501, Daerung Technotown 3th, 448, Gasan-Dong, GeumChun-Ku, Seoul, Korea Tel : +82-2-2107-3700 Fax : +82-2-2107-3707 URL: http://www.woosim.com All specifications are subjected to change without notice http://www.woosim.com...
Page 2
Copyright ⓒ2007 by Woosim Systems Inc. All rights reserved. The information contained in this manual is the property of Woosim Systems Inc. and may not be reproduced in whole or in part without the prior written permission of Woosim Systems Inc.
Page 3
Support text and graphic printing. UART(RS-232C or TTL) interface Easier maintenance with self-diagnostics. In field programming – Update Firmware, Download Fonts and Logos Flow control : Software (XON/XOFF) ※ Hardware flow control not supported in printer. Agency Approvals http://www.woosim.com 2010-02-03...
Do not allow plastic film, erasers, or adhesive tape to touch the paper for long periods. ● Do not stack the thermal paper with diazo copies immediately after copying or wet-type copies. ● Do not use chemical glue. ● Always use the clean thermal paper. http://www.woosim.com 2010-02-03...
Page 5
--Reorient or relocate the receiving antenna. --Increase the separation between the equipment and receiver. --Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. --Consult the dealer or an experienced radio/TV technician for help. http://www.woosim.com 2010-02-03...
None : DC 5V 1.2. Product Part Number System Model n ame Interface S pec. Wired Wireless RS-232C Bluetooth SC30 IrDA None RS-485 Parallel None Serial/Bluetooth Part No. ⇒ S40/A1 Example) 1. Porti-S40 2. Porti-SC30 Bluetooth Only Part No. ⇒ SC30/Z1 http://www.woosim.com 2010-02-03...
Porti-SP Rev. 2.0 2.1. Printer & Accessories When unpacking your printer box make sure it contains the printer and all accessories. If any accessories are missing or damage, please contact your dealer for assistance. PORTI-SP20 PORTI-SP30 Thermal roll paper http://www.woosim.com...
2. Open the paper roll cover by applying your finger on both side of printer, push it up when the lock is released as shown in the drawing. 3. Remove the used paper roll core if there is one. 4. Insert the paper roll as shown. http://www.woosim.com 2010-02-03...
Page 14
Porti-SP Rev. 2.0 5. Be sure to note the correct direction that the paper comes off the roll. 6. Pull out a small amount of paper and then close the cover as shown. 7. Tear off the paper as shown. http://www.woosim.com 2010-02-03...
Porti-SP Rev. 2.0 2.5. Specified Power supply The following specifications are requested for Power supply. Input : DC 5V / Max 2.5A Avoid using power supply which its power capacity of power current is extremely high. http://www.woosim.com 2010-02-03...
Pin no Signal name Direction Function INPUT 5VDC/2.5A Output Transmit Data Input Receive Data Ground <CN2 : MOLEX (53014-0410)> Applicable connector : MOLEX 51004-0410 or equivalent. WARNING A wrong connection of power supply connector could be damage the printer http://www.woosim.com 2010-02-03...
: Indicates a fault condition or a printer error. (i.e : no paper, paper cover opened. etc.) The Porti_PP40 printer has an parallel and RS-232 serial interface are connected by means of a 5 pin female and 15 pin female connector http://www.woosim.com 2010-02-03...
3) After printing the current printer status, Self-Test will print a pattern using the built-in character set. 4) The Self-Test automatically ends. The printer is ready to receive data as soon as it completed the self test. http://www.woosim.com 2010-02-03...
Chemicals or oil may change the color of paper, or printed Characters may fade. Change of paper color starts from approx 70 ℃. Pay attention to heat, humidity and sun light. Color of paper may be changed by being scratched by nail or hard metal, etc http://www.woosim.com 2010-02-03...
Need help?
Do you have a question about the PORTI-SP20 and is the answer not in the manual?
Questions and answers