Download Print this page
FLASHFORGE 3D PRINTER INVENTOR Quick Start Manual

FLASHFORGE 3D PRINTER INVENTOR Quick Start Manual

Hide thumbs Also See for INVENTOR:

Advertisement

Quick Links

Quick Start Guide
INVENTOR
SZ14-EN-A02
WARNING
1. Do not remove the wrapping around the nozzle.
2. Hot! Avoid touching the heating nozzle in operation.
3. Moving parts in printer may cause injury. Do not wear gloves
or other sources of entanglement in operation.
USERGUIDE
The User Guide is in the SD card.
This guide is only applicable to FLASHFORGE Inventor 3D printer

Advertisement

loading

Summary of Contents for FLASHFORGE 3D PRINTER INVENTOR

  • Page 1 2. Hot! Avoid touching the heating nozzle in operation. 3. Moving parts in printer may cause injury. Do not wear gloves or other sources of entanglement in operation. USERGUIDE The User Guide is in the SD card. This guide is only applicable to FLASHFORGE Inventor 3D printer...
  • Page 2: Kit Contents

    Kit Contents Filament Spool x 2 3D Printer After-sales Service Card Quick Start Guide Power Cable USB Cable Spool holder x 2 打印平台调节专用 扫描二维码,观看调平指导视频! 调整平台支架下方的螺母,直至纸片在喷嘴与平台间的 运动感受到轻微的阻力。 注意 1.Extruder hot during operation. CAUTION 使用过程中喷头会发热。 2.Heating plate hot during operation. Allow surface to cool before servicing. Do Not Touch 请勿触摸...
  • Page 3 Getting to Know Your Inventor Extruder Camera 18 19 20 1.Extruder Cable Bunch 2.Filament Guide Tube 3.Y-Axis Guide Rod 4.X-Axis Guide Rod 8.LevelingKnob 5.Build Plate 6.Build Platform 7.Bracket 11.Cooling Fan 12.Spring Presser 9.Z-Axis Guide Rod 10.Touch Screen 13.Turbofan 14.Turbofan Baffle 15.Left Nozzle...
  • Page 4 Quick start guide, After-sales service card, out from the top. levelling card, and two build taps. 3.Firmly grasp the two sides handles of Inventor. 4.Remove the packing bag.(Tip:Save your Lift it out from the carton and place it on a packaging for future transportation and stable surface.
  • Page 5 7.Remove the foam from the back of the logo 8.Remove the bubble wrap from extruder and board. slide the x-axis rod to the middle of the printer. 9.Place the dual extruder on the extruder seat 10.Elevate the build plate to its limit. as show.
  • Page 6: Hardware Assembly

    Hardware Assembly Extruder Assembly 1. Place the dual extruder on the extruder seat. 2. Take the M2.5 Allen Wrench from the tool bag and two M3 x 8 bolts(longer ones) from the extruder’s accessory kit. 3. Adjust the extruder location to align the bolt holes.
  • Page 7 Turbofan Baffle Assembly 1. Use the M2.5 Allen Wrench to remove two turbofan bolts. 2. Take the turbofan baffle from the extruder’s accessory kit. 3. Install the turbofan baffle to the turbofan.
  • Page 8 Turbofan Seat Align the bump on the turbofan seat to the hole in turbofan sub-assembly. 1. Place the turbofan sub-assembly besides the turbofan seat. 2. Insert the bump on the turbofan seat to the turbofan sub-assembly. 3. Screw the two bolts in. 4.
  • Page 9: Leveling Build Plate

    Leveling Build Plate How to change language HOME Filament Level Home Manual Print Preheat Tools Setting Status About 简体中文 Language Fan On WiFi English 繁體中文 FactoryReset Update Pulley 日本語 Deutsch Resume Print Camera 한국어 How to use the leveling knobs Rotate knob clockwise Raise the build plate to reduce the distance between the nozzle and build plate.
  • Page 10 How to level the build plate 1. Tighten the three leveling knobs under the build platform until you cannot tighten them any more. 2. Tap [Tools], [Leveling] to start leveling. 3. The build plate and nozzle will start to move. Wait for them to stop, then adjust the corresponding knob under the right nozzle first using the leveling card.
  • Page 11 Place Filament and Loading Filament 1. Remove PLA filament from packaging. 2. Place filament in spool slots located on both sides of the printer. 3. As shown below, insert spool holder into the center hole of the filament. Rotate 90 degrees to lock.
  • Page 12 1. After filament placement, thread the filament through guide tube. 2. Insert the filament into the left extruder at a perpendicular angle while pressing down the spring presser. Ensure the end of the filament has a flat surface before loading it. 1.
  • Page 13: First Print

    2. Tap [Print]-[SD card], turn to next page, tap [Test Files], click first 3D modeling file, and than tap [print]. Once heated, the printer will start printing automatically. FlashPrint切片软件 测试文件Test Files Happy3D 软件安装包 Software Inventor快速启动指南Quick St Inventor说明书User Guide F-Test left extruder-PLA Print Time: 1:24 F-Test left extruder-PLA 40mm_Box-left extruder-PLA...
  • Page 14 Scan QR to Get More After-Sales Support After-Sales Service: support@ff3dp.com Tel: +86 579 82273989 Web: www.flashforge.com Add: 2/F, No.518, Xianyuan Road, Jinhua, Zhejiang, China...