Download
Share
Print this page
FLASHFORGE 3D PRINTER CREATOR PRO Quick Start Manual
  1. Manuals
  2. Brands
  3. FLASHFORGE 3D PRINTER Manuals
  4. 3D Printers
  5. Creator Pro
  6. Quick start manual

FLASHFORGE 3D PRINTER CREATOR PRO Quick Start Manual

Hide thumbs Also See for CREATOR PRO:

Advertisement

Quick Links

Download this manual
Quick Start Guide
CREATOR PRO
SZ10-EN-A02
WARNING
1. Do not remove the wrapping around the nozzle.
2. Hot! Avoid touching the heating nozzle in operation.
3. Moving parts in printer may cause injury. Do not wear gloves
or other sources of entanglement in operation.
USERGUIDE
The User Guide is in the SD card.
This guide is only applicable to FLASHFORGE Creator Pro 3D printer

Advertisement

loading

Related Manuals for FLASHFORGE 3D PRINTER CREATOR PRO

Summary of Contents for FLASHFORGE 3D PRINTER CREATOR PRO

  • Page 1 2. Hot! Avoid touching the heating nozzle in operation. 3. Moving parts in printer may cause injury. Do not wear gloves or other sources of entanglement in operation. USERGUIDE The User Guide is in the SD card. This guide is only applicable to FLASHFORGE Creator Pro 3D printer...

  • Page 2: Kit Contents

    Kit Contents Filament Spool x 2 3D Printer After-sales Service Card Quick Start Guide Power Cable USB Cable SD Card 打印平台调节专用 扫描二维码，观看调平指导视频！ 调整平台支架下方的螺母，直至纸片在喷嘴与平台间的 运动感受到轻微的阻力。 注意 1.Extruder hot during operation. CAUTION 使用过程中喷头会发热。 2.Heating plate hot during operation. Allow surface to cool before servicing. Do Not Touch 请勿触摸...
  • Page 3 Getting to Know Your Creator Pro 1. Z-Axis Guide Rod 2. Extruder Cable Bunch 3. Slot 4. Y-Axis Guide Rod 7. Leveling Knob 8. SD Card Slot 5. Build Plate 6. Build Platform 11. Cooling Fan 12. Spring Presser 10. Buttons 9.
  • Page 4 Quick Start Guide. 3. Firmly grasp the two side handles of 4. Remove the packing bag. And then Flashforge Creator Pro. Lift it out from the remove the tape and plastic wrap for carton and place it on a stable surface.
  • Page 5 7. Remove the foam container. It should contain: power cable, USB cable, two spool holders, SD card, tool bag, extruder's accessory kit. 8. Slide the X-axis Rods to the very back. 9. Remove lid, which should hold two rolls of filament.
  • Page 6 Anterior Angle 14. Congratulations! You’ve finished the  unpacking process. (Tip: Save your  Flashforge Creator Pro packaging for  future transportation and storage. ) 1. Place the two anterior angles of the lid into 2. Slightly squeeze the two relief angles to place the corresponding front slots.

  • Page 7: Hardware Assembly

    Hardware Assembly Extruder Assembly 1. Place the dual extruder on the extruder seat. 2. Take the M2.5 Allen Wrench from the tool bag and two M3 x 8 bolts(longer ones) from the extruder’s accessory kit. 3. Adjust the extruder location to align the bolt holes.
  • Page 8 Turbofan Baffle Assembly 1. Use the M2.5 Allen Wrench to remove two turbofan bolts. 2. Take the turbofan baffle from the extruder’s accessory kit. 3. Install the turbofan baffle to the turbofan.
  • Page 9 Turbofan Seat Align the bump on the turbofan seat to the hole in turbofan sub-assembly. 1. Place the turbofan sub-assembly besides the turbofan seat. 2. Insert the bump on the turbofan seat to the turbofan sub-assembly. 3. Screw the two bolts in. 4.
  • Page 10 Filament Guide Tube and Filament Installation 1. To install a spool holder, level it and insert the end into the corresponding opening. 2. Turn down the spool holder to make the holder bottom cleave to the printer back. Please refer to the next page for the right method of filament mounting 3.
  • Page 11 Filament Guide Tips Tube Buckle The filament spool must be oriented correctly (see below). The filament guide tube ensures stable printing and protects the printer. After securing the filament and guide tubes, 4. Lock the filament guide tube with thread the filament through the guide tubes. R-shape buckles.
  • Page 12 Leveling Build Platform FF Creator Pro Print from SD Preheat Utilities SD Card Slot FlashPrint GoΣ Happy3D soft Σ PlateLeveling.x3g test model Exit Menu 1. Attach the power supply, plug the power cable into an electrical outlet and turn on the printer.
  • Page 13 How to level the build plate 1. Tighten the three leveling nuts under the build platform until you cannot tighten them any more. 2. Select the PlateLeveling.x3g on the control panel, and tap [OK] to start leveling. Then tap [OK] for page-turning to read the leveling instructions. 3.

  • Page 14: Loading Filament

    Loading Filament FF Creator Pro Print from SD Preheat Utilities Monitor Mode Filament Loading Preheat Settings General Settings Unload right Load right Unload left Load left Heating: R Extruder: L Extruder: 28/200C Platform: 21/ 50C 1. Tap [Utilities] and tap [OK]. Tap [Filament Loading]-[OK] to enter the filament loading/unloading page.
  • Page 15 Scan QR to Get More After-Sales Support After-Sales Service: support@ff3dp.com Amazon.com orders only: 597891915@qq.com Tel: +86 579 82273989 Web: www.flashforge.com Add: 2/F, No.518, Xianyuan Road, Jinhua, Zhejiang, China...