Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for SEWOO LK-P12W
Summary of Contents for SEWOO LK-P12W
- Page 1 SEWOO TECH CO.,LTD. 374-2, Gajang-dong, Osan-si, Gyeonggi-do, 447-210, Korea TEL : +82-31-459-8200 FAX : +82-31-459-8880 www.miniprinter.com MODEL : LK-P12W USER’S MANUAL All specifications are subject to change without notice Rev. 01 07/12...
-
Page 2: Table Of Contents
Table of Contents RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE. DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTION 1. Unpacking 2. Product overview 3. Installation & Usage 3-1. Display 3-2. Installing the Battery 3-3. Removing the Battery 3-4. -
Page 3: Unpacking
1. Unpacking 2. Product overview Standard Front PEELER WING PEELER BODY Printer COVER OPEN DISPLAY BUTTON Battery USB Cable Recharger SERIAL Bottom BATTERY DOOR Quick Reference Optional CHARGER CONNECTOR Serial cable Paper... -
Page 4: Display
3. Setting Up the Product 3-2. Installing the Battery 3-1. Display Button Name function Paper Feed/ Advances the supply. Clears error message. Down button Moves down through menu options. Remove the battery door. Insert the battery as shown. Enter button Selects the highlighted menu option. -
Page 5: Removing The Battery
3-3. Removing the Battery 3-4. Charging the Battery ② ① 1. Turn off the printer. 2. Be sure that the AC plug is correct. If AC plug is wrong, change the plug to the correct one. Remove the battery door. Lift out the battery. 3. -
Page 6: Stock Installation
3-6. Peel Mode 3-5. Stock Installation Peel Mode With a roll of stock installed, slide the Press the feed button. Put the stock in so it unrolls from the Open the Paper cover by pressing the peeler body towards the back of the bottom. -
Page 7: Diagnostic Test
3-7. Diagnostic Test While Peeler mode is “On”, perhaps engraved lines of the label paper are cut too deep, peeling error might occur. Badness Paper Laper Paper Engraved Line Turn off the printer. Press and hold the feed Normal paper button and power button. -
Page 8: Peripherals Connection
4. Peripherals Connection This printeThis product can communicate with other devices via Wifi(802.11b/g) The sample of self test printout communication and cable. 4-1 Wifi(802.11b/g) Connection 1. The Printer can be connected to devices equipped with wifi(802.11b/g) communication capacity (PDAs, PCs, etc.) 2. -
Page 9: Interface Cable Connection
5. Printer cleaning 4-2. Interface Cable Connection If the interior of the printer is dusty, printing quality can be lowered. In this case, follow the instructions below to clean the printer. 5-1. PrintHead Cleaning 1. Use an applicator swab moistened with an isopropyl alcohol to clean the print head and remove any dust. -
Page 10: Printer Specification
6. Printer Specification 6-1. Specification 5-2. Platen Roller Cleaning Printing Method Direct Thermal 1.Clean the platen roller with a clean soft cloth moistened with isopropyl alcohol or a cleaning pen. Printing Speed 80mm/sec Resolution 203 DPI X 203 DPI 2. Turn the platen roller with your finger to clean the entire surface. Character ALPHA NUMERIC Character, Extension Character Barcode... -
Page 11: Cpcl Command Compatibility
7. CPCL Command Compatibility NOTE Battery Charger input AC100~240V, 50/6 Hz Compatible with only Partially output 7.4V, 2200mAh commanders provided by Compatible Compatible Compatible the manufacturer. Battery Battery type Li-ion △ ○ output 7.4V, 18.9wh ● Charging time 3.7 Hrs Charging Printer Commands Compatibility Size... - Page 12 Graphics Compatibility Line Print Mode Compatibility ○ SETLP ○ LINE ○ SETLF ○ INVERSE-LINE Moving With X and Y Coordinates ○ ○ PATTERN LMARGIN ○ ○ GRAPHICS ○ SETBOLD ○ ○ SETSP ○ Advanced Commands Compatibility Special ASCII Characters ○ CONTRAST SETFF ○...
Need help?
Do you have a question about the LK-P12W and is the answer not in the manual?
Questions and answers