Advertisement
EN 44
5.
DVDR730/0x
Chrysalis (CHR)
Nucleus Name
Nucleus Number
Description
User Input
Example
Nucleus Name
Nucleus Number
Description
User Input
Example
Nucleus Name
Nucleus Number
Description
User Input
Diagnostic Software
DS_CHR_DevTypeGet
100
Sends the device ID and the module ids and revisions of the PNX7100 (Chrysalis) to the
stdout port.
None
DS:> 100
Device ID 7100
Codec ID PNX7100_MF2
F-BCU (0x0102) 1.0 INTC (0x011d) 1.0 PCI-XIO(0x0113) 1.0
SIF(0x013b) 1.0 EJTAG (0x0104) 0.0
BOOT (0x010a) 1.0 CONFIG (0x013f) 1.0 RESET (0x0123) 1.0
DEBUG (0x0116) 0.0
UART0 (0x0107) 0.1
UART2 (0x0107) 0.1
UART3 (0x0107) 0.1
I2C1 (0x0105) 0.1
GPIO (0x013c) 1.0
DISP0 (0xa015) 0.1
DISP1 (0xa00f) 0.0
SPU
(0xa00e) 0.0
MIXER (0x0137) 1.0
CCIR (0x0139) 1.0
VDEC (0x0133) 0.1
DV
(0xa00c) 0.0
BEI
(0xa00a) 0.0
SGDX (0xa008)0.0 BYTE (0xa00b) 0.0
ACOMP (0xa000) 0.0
VFE
SCR
(0x0000) 0.0 SIFF (0xa011) 0.0 WMD
AUDIO0 (0xa015) 0.1 AUDIO1 (0xa00f) 0.0 PSCAN (0xa018) 0.0
010000:
Test OK @
DS_CHR_TestImageOn
101
Generates a test-image of a selected video standard on selected video output on the digital
board. When no input is given, the default values will be used. Use nucleus
DS_ANAB_VideoRouting to route the video signal on the analogue board output
The user has to decide which test image, video standard and video output must be used:
Test image id:
0
VERTICAL_COLOURBAR (default)
1
HORIZONTAL_COLOURBAR
2
WHITE
3
YELLOW
4
CYAN
5
GREEN
6
MAGENTA
7
RED
8
BLUE
9
BLACK
10
GRAY
Video standard:
PAL (default)
NTSC
Video output:
ALL
CVBS and YC and RGB (default)
CVBS
YC
RGB
YUV
PSCAN
progressive scan
DS:> 101
010100:
Test OK @
DS:> 101 0 pal cvbs
010100:
Test OK @
DS:> 101 4 ntsc yc
010100:
Test OK @
DS_CHR_TestImageOff
102
Switches the test-image off.
None
S-BCU (0x0102) 1.0
UART1 (0x0107) 0.1
I2C0 (0x0105) 0.1
SYNC (0x013a) 1.0
OSD
(0x0136) 0.1
DENC (0x0138) 0.1
PARSER (0xa00d) 0.0
IDE
(0xa009) 0.0
OUTPUT (0xa003) 0.0
(0xa001) 0.0
VCOMP (0xa002) 0.0
(0xa010) 0.0
Advertisement
