Advertisement
EN 148
9.
DVDR730/0x
R
I
SET1,2
S C L
I
S D A
I / O
A L S B
I
I 2 C
I
V
P
DD_IO
V
P
D D
V
P
AA
V
I / O
REF
E X T _ L F
I
R T C _ S C R _ T R
I
9.9
List of Abbreviations
Analog Board
+5VSTBY
8SC2
A_DATA
A_RDY
A18 - A19
A8 - A17
AD0 - AD7
AFC
AFEL
AFER
AGC / WSRI
AINFL
AINFR
AKILL
ALADC
ALDAC
ALE
AM0
AM1
ARADC
ARDAC
ASCC1
AVCC
AVSS
CFIN
CS0_
CS2_
CVBSFIN
D_DATA
Circuit-, IC descriptions and list of abbreviations
A
760 Ohms resistor must be connected from this pin to AGND and is used to
control the amplitudes of the DAC outputs.
Multifunctional input: MPU Port Serial Interface Clock Input.
Multifunctional pin: MPU Port Serial Data Input/Output.
Multifunctional pin. TTL Address Input. This signal sets up the LSB of the MPU
address.
When this pin is tied low the I2C filter is activated which reduces noise on the I2C
interface. When this pin is tied high, the input bandwidth on the I2C lines is
increased.
When this input pin is tied high [Vdd_IO], the ADV7302A/03A interfaces over the
I2C port.
Power supply for digital i/ps and o/ps
Digital power supply
Analog power supply
Optional External Voltage Reference Input for DACs or Voltage Reference
Output (1.235V).
External Loop filter for the internal PLL.
Multifunctional Input: Real Time Control (RTC) input, Timing Reset input,
Subcarrier Reset input.
Permanent Supply 5V
Pin8 Scart2 (only for Europe)
Data from Analog- to Digital-Board
(UART-Communication)
Analog-board ready (status
information to digital-board)
Parallel Address Bus (CC - Flash-
ROM and S-RAM)
Parallel Address Bus (CC - Flash-
ROM and S-RAM)
Parallel Address Bus (CC - Flash-
ROM and S-RAM)
Automatic Frequency Control
Audio Frontend Left
Audio Frontend Right
Automatic Gain Control (for Europe),
Wide Screen Rear In (for NTSC)
Audio In Front Left
Audio In Front Right
Audio Kill Signal
Audio Left to ADC
Audio Left from DAC
Address Latch Enable
Adress-mode 0
Adress-mode 1
Audio Right to ADC
Audio Right from DAC
Audio Scart 1 Mute (System Clock
Output for Real time Clock-
Adjustment)
Power Supply for A/D-converter
GND-Pin for A/D-converter
Chroma Front In
Chip Select 0 (CC - S-RAM)
Chip Select 2 (CC - Flash-ROM)
Video Front In
Data from Digital- to Analog-Board
(UART-Communication)
D_RDY
Digital-board ready (status information
from digital-board)
DAC_MUTE
Mute Signal for DAC
DAOUT
Digital Audio Out
DVAL
Audio from Digital Video In Left
DVAR
Audio from Digital Video In Right
DVCC1
Power Supply Pin
DVCC2
Power Supply Pin
DVCC3
Power Supply Pin
DVSS1
GND Pin
DVSS2
GND Pin
DVSS3
GND Pin
FAN_OFF
Fan for Basic engine
FBIN
Fast Blanking input
FOME
FOllow ME Status line (matching
signals yes/no; only for Europe)
G1...10
DISPLAY GRID
INT
Interrupt OUT for the CC
INT
Interrupt – line from Display Print
ION
Inverse ON-Line
IPFAIL
Inverse Power Fail Detection
IPOR
Inverse Power On Reset
IRESET
Inverse Reset Input
K1
Key-Input-Line
K2
Key-Input-Line
KILL
Signal from IR-Receiver
P50 IN
P50 INput-line (only for Europe)
P50 OUT
P50 OUTput-line (only for Europe)
POR_DC
Power On Reset for Display Control
Print (Ext_DL)
PSS
Output Enable ReaD (CC - Flash-
ROM and S-RAM)
PWM_FIL
Control line for Filament Voltage
Generation
PWONSW
Amplifier Switch Audio A/D Converter
RD_
Pal/Secam-Select
RECLED
Control Signal for REC-LED
RESET_DIG
Reset Line to Digital Board
RP_
Inverse Reset line to Flash-ROM
RSA1/2
Record Selector 1/2
Advertisement
