Jayco Precept 2018 Owner's Manual
  1. Manuals
  2. Brands
  3. Jayco Manuals
  4. Motorhomes
  5. Precept 2018
  6. Owner's manual

Jayco Precept 2018 Owner's Manual

Class a
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
2016 CAMPING TRAILERS
2018
Class A Motorhome
Owner's Manual
PRINTED ON RECYCLED PAPER
0230295.2018

Advertisement

Table of Contents
loading

Related Manuals for Jayco Precept 2018

Summary of Contents for Jayco Precept 2018

  • Page 1 2016 CAMPING TRAILERS 2018 Class A Motorhome Owner’s Manual PRINTED ON RECYCLED PAPER 0230295.2018...
  • Page 3 44,683 people. We’re proud of our results, and we know those numbers show that a little initiative can go a long way. The Jayco EcoAdvantage is our way of making sure endless generations can enjoy the Great Outdoors.

  • Page 5: Table Of Contents

    Change Of Address/Ownership Suggestions For Obtaining Service Obtaining Service For Separately Warranted Items Obtaining Service At Our Customer Service Facility Parts & Accessories Notice To Jayco Dealers Section 2: Occupant Safety Secondary Means of Escape (Exit Window) Exit Window Label Fire Safety...
  • Page 6 Table of Contents Rear Vision Camera Campsite Hook-Up Lippert Motorized Leveling Plus (If So Equipped) Emergency Stopping Emergency Towing Front Axle Tire Alignment Wheel Lug Nuts/Wheel Liners Tires Changing A Tire Awnings (if so equipped) Awning Care Electric Patio Awning With Remote Control In Motion Detector (if so equipped) Power Awnings (if so equipped) Carefree®...
  • Page 7 Table of Contents 12-Volt Battery Disconnect Battery Isolator Solenoid (If So Equipped) Battery Isolation Manager (If So Equipped) Auxiliary Start System (If So Equipped) Load Center 120-Volt Circuit Breakers Approximate Electrical Load Ratings 120-Volt (50 AMP) AC System (if so equipped) 50-AMP Power Cord (if so equipped) Calculating 50 AMP Electrical Load (if so equipped) Generator...
  • Page 8 Table of Contents Draining The Fresh Water System Filter housing Nautilus P3 Uni-Dock Utility Center Low point drains Exterior fresh water drain SANITIZING THE PLUMBING SYSTEM: WINTERIZING THE PLUMBING SYSTEM: Truma® Tankless Water Heater (If So Equipped) Outside Shower (If So Equipped) Faucets Bathroom Tub / Shower Black/Grey Water System and Tanks...
  • Page 9 Table of Contents Cabinetry & Tables Interior Wall Panel ABS Plastics Sofa & Dinette Hide-a-bed Sofa or Sofa Sleeper Jack Knife Sofa Dream Dinette unlocked Dream Dinette locked Trifold Sofa Booth Dinette (If So Equipped) Booth Dinette Dream Dinette Free Standing Dinette Chairs (If So Equipped) Pantry or Hutch (If So Equipped) Countertops Laminate countertops (if so equipped)
  • Page 11 WARNING: READ ALL INSTRUCTIONS IN THIS MANUAL AND COMPONENT MANUFACTURER SUPPLIED INFORMATION BEFORE USING YOUR RV. This manual has been provided by your recreational vehicle manufacturer for the sole purpose of providing instructions concerning the operation and maintenance of this recreational vehicle.
  • Page 12 Maintenance Record Table of Contents...

  • Page 13: Customer Relations

    Canada may differ to conform to Canadian Codes. Dealer Responsibility At the time of sale of the new recreation vehicle, your Jayco dealer is expected to: Deliver your recreation vehicle in the best condition possible. Your recreation vehicle must pass the dealer’s pre-delivery inspection (PDI), including all systems tests.
  • Page 14 (or any effect of the alterations) to any of the parts, components, systems or assemblies installed by Jayco. Jayco is not responsible for the safety or quality of design features, materials or workmanship of any alterations by such suppliers.

  • Page 15: To Contact Us

    Canada. In addition, the club offers a variety of local and regional activities throughout the year. By belonging to the Jayco Travel Club, you will find new ways to enjoy your RV and make friends all across the country.

  • Page 16: About This Manual

    Section 1: Warranty & Service About This Manual This manual is a guide to operation of the features, equipment and controls in your recreation vehicle. If you find components vary significantly from what is described, please contact your dealer to ensure you have the correct information. Nothing in this manual creates any warranty, either expressed or implied.

  • Page 17: Reporting Safety Defects

    Section 1: Warranty & Service NOTE: Gives helpful information. This is the safety alert symbol. It is used to alert you to potential personal injury hazards. Obey all safety messages that follow this symbol to avoid possible injury or death. ...

  • Page 18: Customer Responsibility

    Section 1: Warranty & Service To contact NHTSA by phone: Call the Department of Transportation (DOT) Vehicle Safety Hotline at 1-888- 327-4236, and a NHTSA representative will record your complaint information (TTY: 1-800-424-9153 or 1-202-484-5238). To Contact NHTSA by mail: Office of Defects Investigations/CRD NVS-216 1200 New Jersey Ave SE...

  • Page 19: Suggestions For Obtaining Service

    Section 1: Warranty & Service Suggestions For Obtaining Service To help ensure your dealer provides the level of service you expect, here are some suggestions we would like to make: Contact your dealer at once… Do not wait until you are ready to use your RV. Your dealer may not be able to service it immediately and/or the repair may require parts be ordered.

  • Page 20: Parts & Accessories

    Section 1: Warranty & Service The propane system (if so equipped) and all electrical systems must be shut down and turned off. We are not responsible for discharged batteries or propane tanks. During the appropriate season, please ensure the RV has been winterized. Unless prior approval has been obtained from our Customer Service facility, all personal items must be removed from the area where you are requesting service repair and the refrigerator emptied.
  • Page 21 TITLED OR REGISTERED IN A BUSINESS NAME OR WHEN THE JAYCO IS SOLD IN CANADA. There is no warranty of any nature made by Jayco beyond that contained in this Limited Warranty. No person has authority to enlarge, amend or modify this Limited Warranty. The dealer is NOT Jayco’s agent.
  • Page 22 REPAIR REMEDY: Jayco’s obligation is to repair any covered defect discovered within the warranty coverage period provided: (l) you notify Jayco or an authorized dealer within 10 days of your discovery of a defect; AND (2) you deliver the Motorhome to Jayco OR an authorized dealership at your cost and expense.
  • Page 23 Provide the notification mentioned in (1), above, within ten (10) days of the discovery of a defect in material or workmanship; and, Promptly schedule an appointment with and take the Motorhome to Jayco or an independent, authorized dealer. If you need assistance, you may contact:...
  • Page 24 Jayco, your Warranty will be registered. The failure to submit this warranty registration to Jayco will not affect your rights under this limited warranty as long as you can present proof of purchase, however, it can cause delays in obtaining the remedies offered by this limited warranty, and it may adversely affect any servicing facility’s ability to...
  • Page 25 Limited Warranty will not apply to this RV. The Motorized Rental Limited Warranty applies in that situation. If, on the other hand, the Jayco dealer sells this RV to a retail customer then the rental warranty would not be applicable. The rental warranty does not apply to retail consumers.
  • Page 26 Motorhome when you take delivery of your Motorhome, you MUST notify your Jayco within 10 days of the date of purchase to have defect or damage repaired at no cost to you. Minor adjustments will be performed, free of charge, within 90 days of your purchase;...
  • Page 27 Section 1: Warranty & Service contact Jayco, at 903 South Main Street, P. O. Box 460, Middlebury, Indiana 46540, Attn: Customer Service, (574) 825-5861 or (800) 283-8267. WHAT IS NOT COVERED: Equipment and appliances installed after the Motorhome is assembled by Jayco; Motorhomes used for any business and commercial purpose other than for rental purposes;...
  • Page 28 CARE AND MAINTENANCE: It is your responsibility to perform proper care and maintenance of the Motorhome and to assure correct load distribution. For details regarding this, please see your owner’s manuals. Please review all manuals and contact Jayco or the supplier of the component part if you have questions.

  • Page 29: Secondary Means Of Escape (Exit Window)

    Section 2: Occupant Safety Secondary Means of Escape (Exit Window) Your recreation vehicle has been equipped with a window(s) that serves as a secondary means of escape. The window(s) will allow a quick exit from the vehicle during an emergency if access to the main entrance door is not available.

  • Page 30: Fire Safety

    Section 2: Occupant Safety Lever style latch Remove the screen by pulling the red tab (upper rightarrow). Pull the lever out from the sash clamps. Swing the lever out so it is positioned straight out from the window. Push the lever (and window) out to open and exit the vehicle.

  • Page 31: Smoke Alarm

    Section 2: Occupant Safety Inspection and maintenance Read and follow all instructions on the label and user’s manual provided by the fire extinguisher manufacturer. Inspect the extinguisher at least once a week (more frequently if it is exposed to weather or possible tampering).
  • Page 32 Section 2: Occupant Safety The smoke alarm is operational once the battery is correctly installed. It will not function if the battery is missing, disconnected, dead, the wrong type or not installed correctly. It requires one standard 9V battery. Refer to the user’s guide, for correct battery and installation information, The LED light will indicate the battery is functioning properly.

  • Page 33: Combination Carbon Monoxide /Propane Alarm

    Section 2: Occupant Safety Combination Carbon Monoxide /Propane Alarm Your recreation vehicle is equipped with a combination carbon monoxide (CO) / propane alarm that is listed for use in recreation vehicles. The combination carbon monoxide/ propane alarm will only work if it is operational and maintained. ...

  • Page 34: Carbon Monoxide/Propane Alarm

    Section 2: Occupant Safety by either exiting the recreational vehicle or calling for assistance. Young children and household pets may be the first affected. Your combination carbon monoxide/propane alarm is designed to detect the toxic carbon monoxide fumes that result from incomplete combustion, such as those emitted from appliances, furnaces, fireplaces and auto exhaust.
  • Page 35 Section 2: Occupant Safety equipment and appliances, and inspect for proper operation of this equipment. Make sure that motor vehicle(s) are not, and have not been, operating in an attached garage or adjacent to the recreation vehicle. If problems are identified during this inspection, have the alarm serviced immediately. Note any combustion equipment not inspected by the technician and consult the manufacturer’s instructions or contact the manufacturer directly for more information about carbon monoxide safety and this alarm...

  • Page 36: Formaldehyde

    Section 2: Occupant Safety NOTE: The carbon monoxide/propane alarm manufacturer strongly recommends replacement of the detector five years after the date of purchase. Formaldehyde Some components in the recreation vehicle contain formaldehyde-based adhesives that may release formaldehyde fumes into the air for an unknown period of time. Individuals who are allergic to formaldehyde gas fumes may experience irritation to eyes, ears, nose and throat.
  • Page 37 Section 2: Occupant Safety Condensation Condensation is a natural phenomenon. The amount of condensation will vary with climate conditions, particularly the relative humidity. Condensation occurs because there is water vapor present in the air. When the temperature reaches the “dew point” the water vapor in the air condenses and changes to a liquid form.
  • Page 38 Section 2: Occupant Safety Notes: Maintenance Record Table of Contents...

  • Page 39: Vehicle Labels

    Section 3: Pre-travel information Vehicle Labels Decals and data plates used throughout the motor home aid in its safe and efficient operation; others give service instructions. Read all decals, data and instruction plates before operating your recreation vehicle. Any decal, data or instruction plate painted over, damaged or removed should be replaced.

  • Page 40: Towing & Braking Warning Label

    Section 3: Pre-travel information OCCC Label (Occupant & Cargo Carrying Capacity): The upper portion of this yellow label is federally required and indicates the total combined weight value of occupants and cargo that may be placed in or on your motor home as it was manufactured and weighed before leaving the factory.

  • Page 41: Loading Your Motorhome

    Section 3: Pre-travel information Loading Your Motorhome  Never load the motor home in excess of the GVWR or the GAWR for either axle. Overloading your motor home may result in adverse handling characteristics and damage to the chassis. DO NOT EXCEED YOUR GVWR! This means you should weigh your vehicle as loaded for your normal travel to determine the actual weight.

  • Page 42: Trailer Plug

    Section 3: Pre-travel information Trailer Plug If you choose to tow behind your RV, a chassis manufacturer supplied 7-way trailer plug (located at the hitch) is pre-wired into your motor home. Before hitching up to a trailer, please read Using the Rear Hitch, vehicle weight ratings, etc. Your motor home may have both 4-way and 7-way trailer receptacles.
  • Page 43 Section 3: Pre-travel information See the Weight Terms and Loading Your RV sections for important information on how towing a vehicle affects the motor home weight.  It is important to redistribute the load to avoid component failure as well as to improve the handling characteristics of the vehicle.
  • Page 44 Section 3: Pre-travel information Notes: Maintenance Record Table of Contents...

  • Page 45: Vehicle Operation

    Section 4: Vehicle Operation Vehicle Operation Your motor home will travel safely and comfortably at highway speed limits. However, it will take longer than a passenger automobile to reach that speed. Allow more time to go around the vehicle you are passing. Avoid situations that might require sudden momentum changes as the length of the motor home affects your ability to quickly cut back into traffic.

  • Page 46: Using The Rear Hitch

    Section 4: Vehicle Operation Using The Rear Hitch  Do not install a frame equalizing type hitch on your motor home. Towing will affect vehicle handling, durability and fuel economy. Exceeding any of the listed weight ratings will result in unacceptable overall vehicle performance. Your safety and satisfaction require proper use of correct equipment.

  • Page 47: Power Entrance Step

    Section 4: Vehicle Operation In addition, a separate supplemental braking system must be installed if the towed trailer or vehicle meets or exceeds the minimum weight determined by the chassis manufacturer (this minimum weight rating will vary by chassis and chassis manufacturer). Contact your dealer for assistance in determining whether a separate braking system is recommended for your towing and traveling safety.

  • Page 48: Keyless Entry (If So Equipped)

    Section 4: Vehicle Operation NOTE:Locks on entrance and baggage doors need biannual lubri- cation using a light coat of silicone spray. Conditions such as rain, salt, dust and pollution may increase the maintenance needs. Keyless Entry (if so equipped) The keyless entry system is a battery powered system. The following is an overview for programming and changing batteries on the lock system.
  • Page 49 Section 4: Vehicle Operation To set a new code, wake up the lock by touching the wake up area. Then touch and hold both the “3|4” button and the ENTER Button for 2 seconds. The system will provide three short beeps, indicating it is ready to accept a new code.
  • Page 50 Section 4: Vehicle Operation Trouble shooting After installation the touch pad does not work ● Batteries are dead/need to be replaced or are not installed properly ● Plug not engaged properly Dead Bolt not engaging into Door Frame ● Obstruction in Door Frame Code not working ●...

  • Page 51: Driver & Passenger Seat

    Section 4: Vehicle Operation Driver & Passenger Seat  Do not adjust the seat while driving. After adjusting the seat, make sure that it is locked in position. To ensure that the seat is locked securely, try to move the seat forward or backward without using the adjusting lever or button.

  • Page 52: Seat Belts

    Section 4: Vehicle Operation Seat Belts  Seat belts should always be worn by anyone who drives or rides in this vehicle. Never use one seat belt for more than one occupant. Never carry more people in the motor home than there are seat belts. Only seats equipped with seat belts are to be occupied while the vehicle is in motion.

  • Page 53: Instrument Panel

    Section 4: Vehicle Operation Instrument Panel For detailed diagrams of the driver’s front dash instrument panel, driver and passenger front dash consoles, and control center refer to the Dash Instrument Panel section of this manual. Refer to your Chassis Guide for additional information on dash controls and vehicle operation.

  • Page 54: Campsite Hook-Up

    Section 4: Vehicle Operation The monitor is operational whenever the engine is running. To use the monitor, flip the switch from standby to ON (the monitor will also work when with the motor home is in “reverse” and the monitor in standby). Make sure you turn the monitor to standby while driving to avoid being distracted.
  • Page 55 Section 4: Vehicle Operation  Failure to act in accordance with the following warnings may result in serious personal injury or death! The use of the electronic automatic leveling system to support the coach for any reason other than which it is intended is prohibited and will violate terms of the limited warranty.
  • Page 56 Section 4: Vehicle Operation Left jack button: activates left jacks in manual mode. Right jack button: activates right jacks in manual mode Rear jack button: activates rear jacks in manual mode Auto Leveling Operation Landing gear jacks can be operated any time the system is “ON”. Turn the leveling system ON by pressing the ON/OFF button.

  • Page 57: Emergency Stopping

    Section 4: Vehicle Operation Retract procedure Press ON/OFF button to turn on the system.Push and hold the RETRACT ALL JACKS button only until the power unit turns on and the coach begins to lower. Release the button once the retract process has begun. NOTE: If you wish to stop the jacks from retracting, press the ON/ OFF button to turn the system OFF, then push it again to turn the system ON.

  • Page 58: Emergency Towing

    Section 4: Vehicle Operation Place the first warning indicator on the traffic side of the recreation vehicle, directed at the nearest approaching traffic. Place the second warning indicator 100 feet behind the recreation vehicle in the center of the lane and toward approaching traffic. Place the third warning indicator 100 feet in front of the recreation vehicle in the center of the lane and away from the traffic approaching from behind.

  • Page 59: Wheel Lug Nuts/Wheel Liners

    Section 4: Vehicle Operation NOTE: Always have the alignment checked and adjusted by a qualified shop with the proper equipment to handle heavy vehicles. NOTE: A road test by the dealer should be included as part of the pre-delivery inspection. The dealer can check for and correct any steering problems before you take delivery.

  • Page 60: Tires

    Section 4: Vehicle Operation Wheel lugs If you suspect or notice the wheel stud bolts are cracked or broken, they must be replaced, along with adjacent bolts that have probably also been weakened due to the additional stress placed on them. Aluminum Wheels (if so equipped) Clean the aluminum wheels with a cleaner that is designed for use on aluminum and apply an appropriate protection agent.
  • Page 61 Section 4: Vehicle Operation  Tire wear should be checked frequently. Once a wear pattern becomes firmly established in a tire it is difficult to stop, even if the underlying cause is corrected. Tire pressure  Failure to follow proper inflation guidelines may result in tire failure, which, under certain circumstances can cause loss of vehicle control or accidents that may result in property damage, bodily injury and/or death.

  • Page 62: Changing A Tire

    Section 4: Vehicle Operation Changing A Tire  The motor home is very heavy. Raising the motor home to replace the spare tire should only be done with extreme caution by a qualified technician. The vehicle could slip, causing personal injury or death. DO NOT ATTEMPT TO DO THIS YOURSELF.

  • Page 63: Awning Care

    Section 4: Vehicle Operation Awning Care Keep your awnings clean and in good condition to prevent costly repairs. Periodically check that the fasteners are tight. Tighten if necessary. Keep the awning fabric clean. For detailed cleaning information, refer to the manufacturer’s owner information.

  • Page 64: Carefree® Longitude Awnings (If So Equipped)

    Section 4: Vehicle Operation Carefree® Longitude Awnings (if so equipped) offer the following features: Scissor style arms that do not require vertical ground supports. Adjustable arms with ( 6 ) position pitch adjustment. Worm gear driver motor eliminating the need for travel locks. Single switch operation, 12V motorized awning.
  • Page 65 Section 4: Vehicle Operation Always operate the awning according to the instructions. Periodically check that the fasteners are tight (tighten if necessary). Keep the awning fabric and arms clean. Refer to the manufacturer’s user guide for detailed operating and safety information. Emergency Operation If power to the vehicle is not available, the awning can be retracted by jumping the motor using a 10VDC –...
  • Page 66 Section 4: Vehicle Operation NOTE: If the awning is equipped with the Direct Response system, this procedure is not applicable. See the manufacturer’s owner’s manual for additional information. Locate and separate the quick disconnects located in the motor arm channel. Position the wires from the motor on the outside of the channel.

  • Page 67: Electric Slide Room(S) (If So Equipped)

    Section 5: Slideout Systems Electric Slide Room(s) (if so equipped) The mechanical components of the slide out are gear driven. Electric powered slideout room systems have a manual override to allow you to extend or retract the slideout room(s) in case of a power loss.

  • Page 68: Slideout Overlap-Outside

    Section 5: Slideout Systems Operating the switch after the room is fully extended or retracted may damage the switch and motor. After the slideout is extended, visually inspect the slideout and the surrounding area to make sure the slideout has extended properly and has adequate clearance from any outside obstructions.
  • Page 69 Section 5: Slideout Systems NOTE: For long-term storage it is recommend the room be closed (retracted). Electric Operation NOTE: Install transit bars (if so equipped) on the slideout room during storage and transportation. Extending/retracting the room Level the unit. Main Power switch at stepwell (locations may vary) must be Verify the battery is fully charged and hooked up to the electrical system.

  • Page 70: Schwintek In-Wall Slideout System

    Section 5: Slideout Systems NOTE: Do not operate the switch after the room is fully extended or retracted as damage can occur to the motor and/or switch. Schwintek In-Wall Slideout System The in-wall slideout system requires no maintenance or adjustments. This system has two vertical columns with a drive motor located at the top of each column.
  • Page 71 Section 5: Slideout Systems the room is extended. Trouble shooting the in-wall slideout system Checking Fuses: The in-wall slide requires a minimum 30-amp fuse. Check the load center for blown fuses and replace any if necessary. If the fuse blows immediately upon replacement, there is a problem with the wiring to the in-wall slide control box.
  • Page 72 Section 5: Slideout Systems approximately 5 seconds. The red and green LED’s will flash indicating you are in override mode. Release the mode button. Using either a wall or command center panel switch, press and hold the switch toward the word IN or RETRACT until the unit comes in completely. This will allow you to get the recreation vehicle to a service center to have the slideout malfunction diagnosed.

  • Page 73: Error Codes

    Section 5: Slideout Systems Pull the motor up until it disengages (about 1/2 inch). Repeat this process for both sides of the slide room. 10. Physically push/ pull the room back into the opening; keep both sides relatively even. 11. The room must be travel locked to keep the room in place for road travel. ...

  • Page 74: Norco Slideout Manual Operation

    Section 5: Slideout Systems unit (or use a ratchet to actuate the motor) to pull the room in or out. If the motor is functioning, check the room for obstructions. Norco Slideout Manual Operation Locate the included flexible shaft in your owner’s packet.
  • Page 75 Section 5: Slideout Systems If the room does not move when the switch is pressed, check the following: Make sure the slideout system is turned on. Battery is fully charged and connected. Transit bars have been removed (if so equipped). ...

  • Page 76: Fig.1 Slideout Controller

    Section 5: Slideout Systems The room is now free to move. Using either a 5/8” or 3/4” wrench or socket, crank the room either in or out completely. If the slideout system is supplied with a gearbox override (optional), use the crank handle to move the room.
  • Page 77 Section 5: Slideout Systems Turn ON the on/off switch or key. Press and hold the OUT button (Fig 4). To retract, press and hold the IN button. There will be a slight delay before the room begins moving. The GREEN LED should be solid ON when room is in motion.

  • Page 78: Preventative Maintenance

    Section 5: Slideout Systems Fault Codes Fault Fault Type Description Possible Cause Possible Solution Code -Stops have not been set Steps need to be programmed by an authorized Major Stops not programmed -Stops were cleared service facility. -Stops were improperly set Run room in opposite direction.
  • Page 79 Section 5: Slideout Systems NOTE: After overriding the system, the room control will need to be re-programmed by an OEM authorized dealer. Emergency Retract Mode: Use this procedure when there is NO loss of power or electrical problem with the system. Remove the touchpad (Fig 4) from the wall.
  • Page 80 Section 5: Slideout Systems Unplug the motor from the harness and remove the motor by lifting it up and out. Repeat steps 1-4 for the other side. Place a socket wrench with a 3-inch extension and a 5/8” deep well socket (Fig 12) through the motor access opening and seat the socket onto the coupler (Fig 13).
  • Page 81 Section 5: Slideout Systems Power Gear Ram Slideout System Typically used for Class C motorhomes. Manual Override Procedure: The system has been equipped with 3/4” hex override couplers located on the drive component of the system. Due to the size and weight of some rooms, assistance may be needed to push the room in.
  • Page 82 Section 5: Slideout Systems 12. Return the brake release lever back to the “engaged” position (parallel to the spring lock lever). Pressing the bent end of the spring lock lever will allow the brake lever to be moved. 13. Plug the motor connector back in again. 14.

  • Page 83: The Electrical System

    Section 6: Electrical System The Electrical System The RV electrical system is comprised of two independent electrical systems. One operates off of 12-volt DC power and the other off of 120-volt 60hz AC power. All installations have been made in compliance with industry standards applicable on the date of manufacture. Because the electrical equipment and associated circuitry are engineered into a dedicated system specific to your RV, do not make unauthorized changes or add fixed appliances to it.

  • Page 84: Controls And Switches

    Section 6: Electrical System Controls and Switches Your motor home is equipped with various switches and controls that allow you to operate and monitor the systems in your motor home. Information on these controls and their location will be provided throughout this manual. Additional information on the various components can be found in the component manufacturer’s user guide.

  • Page 85: Gfci Receptacle

    Section 6: Electrical System The dimmer has a memory so it remembers what the light setting was when the lights were turned OFF. When turned ON again, the lights return to that same setting. NOTE: If your RV model includes the 5 way/8 way remote control: the LIGHT button on the remote only controls the awning LED lights GFCI Receptacle There is a ground fault current interrupter (GFCI) engineered into the electrical system.

  • Page 86: Connecting The Power Cord

    Section 6: Electrical System  Do not hook up the power cord to any receptacle until you have verified proper polarity and grounding. DO NOT plug the shore power cord into a campsite receptacle(s): That has reverse polarity With non-functioning ground circuits That shows outward signs of heat damage.

  • Page 87: Inverter (If So Equpped)

    Section 6: Electrical System Plug the power cord into the receptacle. Be sure all the power cord prongs are properly plugged into the receptacle. Return to your RV and turn “on” the load center main circuit breaker. The shore line power cord should be unplugged when the recreation vehicle is left unattended.
  • Page 88 Section 6: Electrical System If your lights are dimming or flickering that usually indicates an overloaded converter. Remove some of the load by turning off DC lights or appliances. Fan is controlled by load. It will begin running at 3 to 6 amp DC draw. It increases in speed with a higher load until 14 to 15 amps.

  • Page 89: Converter W/Charge Wizard (If So Equipped)

    Section 6: Electrical System Converter w/charge wizard (if so equipped) Some converters may be equipped with a charge wizard There are (3) possible charging modes; NORMAL, BOOST and STORAGE. The charge wizard will automatically select the best mode to charge your battery. A green LED next to the wizard mode button will indicate by flashes, which mode is currently being used.

  • Page 90: Batteries

    Section 6: Electrical System Replacing a fuse Before replacing a fuse, always turn off the electrical components protected by it. Disconnect the shore power cord. Turn “off” the inverter (if so equipped). Disconnect the house or auxiliary batteries main negative battery cable. Remove the fuse panel cover to check fuses.

  • Page 91: House Batteries

    Section 6: Electrical System House Batteries Your motor home is equipped with Group 27 deep cycle batteries. Unless a battery has been fully discharged, house auxiliary batteries are normally charged in one of two ways: When the power cord is plugged into 120-volt shore power, or when the generator (if so equipped) is operational, the inverter/charger functions as a battery charger and will automatically charge the house batteries when required.

  • Page 92: Volt Battery Disconnect

    Section 6: Electrical System Refer to your Chassis Guide for information pertaining to the chassis batteries. 12-Volt Battery Disconnect The 12-volt battery disconnect switch is typically located near the entrance door. This momentary switch controls a solenoid which connects or disconnects the house batteries. The switch lights up red when turned on.

  • Page 93: Load Center

    Section 6: Electrical System The auxiliary start switch can momentarily connect both the house and chassis batteries should the chassis battery become discharged. To operate, depress either the “Aux. Start” switch (located on the front driver’s dash) or the Battery Boost switch on the driver console and hold it down.

  • Page 94: Approximate Electrical Load Ratings

    Section 6: Electrical System Replacement Only replace circuit breakers with those of the same specified type, voltage, and current rating. Never replace a circuit breaker with one listed at a higher amperage rating. Please contact your dealer for repair assistance when replacing circuit breakers. Maintenance At the beginning of camping season, inspect the circuit breakers and replace as needed.

  • Page 95: Volt (50 Amp) Ac System (If So Equipped)

    Section 6: Electrical System 120 Volt System Air cConditioner 18 AMPS Coffee Maker 6-12 AMPS Converter (each) 8 AMPS DVD System 3 AMPS Fireplace 12 AMPS Hair Dryer or Curling Iron 10-14 AMPS Microwave 12 AMPS Refrigerator 6 AMPS Satellite Receiver 2 AMPS 2-4 AMPS Vacuum Cleaner...

  • Page 96: Amp Power Cord (If So Equipped)

    Section 6: Electrical System 50-AMP Power Cord (if so equipped)  Do not hook up the power cord to any receptacle until you have verified proper polarity and grounding. Polarity indicators can be purchased in most electrical and hardware stores. Do not use any cheater plug, adapter or extension cord to reconfigure incoming AC power or break the continuity of the circuit connected to the grounding pin.

  • Page 97: Generator

    Section 6: Electrical System Generator Your motor home may be equipped with an LP or diesel powered generator. The generator in your motor home produces 120/240-volt power compatible with the motor home electrical NOTE: If your motor home is equipped with the Vega Touch touch- screen system (Entegra) the generator instructions can be found in the Vega Touch User Guide included in your warranty portfolio (or online at http://www.fireflyint.com).

  • Page 98: Maintenance

    Section 6: Electrical System  CARBON MONOXIDE IS DEADLY! Do not run the generator when your motor home is indoors or in a confined space. Asphyxiation or carbon monoxide poisoning hazards exist whenever generator exhaust gasses can accumulate. MOVING PARTS AND ELECTRICITY can cause severe personal injury or death.

  • Page 99: Starting The Generator

    Section 6: Electrical System  Excessive usage can overheat and damage the generator starter motor. Do not engage the starter motor for more than 20 seconds at a time. If the generator doesn’t start after the first attempt, wait at least two minutes before beginning another start sequence.

  • Page 100: Solar Prep (If So Equipped)

    Section 6: Electrical System seconds. Once the generator starts running, release the “START/STOP” switch. The indicator above the switch will light up. For better performance and engine life, especially in colder weather, let the generator engine warm up for two minutes before turning “on” 120-volt appliances. The small display (hour meter) is used to keep track of run time on the generator.

  • Page 101: Fuel Safety

    Section 7: Fuel & Propane System Fuel Safety  Automotive fuels can cause serious injury or death if misused or mishandled. If you have further questions, consult your dealer or Customer Service for assistance. Always shut OFF the vehicle engine while refueling. Do not bring or store fuel or other flammable liquids inside the motor home because a fire or explosion may result.

  • Page 102: Propane Gas System (If So Equipped)

    Section 7: Fuel & Propane System Windows should be closed while driving or running the generator (if so equipped) to avoid drawing dangerous exhaust gases into the motor home. If you suspect that exhaust fumes are entering the passenger compartment, have the cause determined and corrected as soon as possible.

  • Page 103: Propane Gas Container

    Section 7: Fuel & Propane System NOTE: All propane lines have been checked with air pressure at the time of manufacture. Dealers are required to recheck and adjust pressure before retail delivery. The following label should be kept permanently affixed to the motor home: Propane Label Propane Gas Container Propane is a true gas compressed into a liquid form.

  • Page 104: Lp Gas Container Overfill

    Section 7: Fuel & Propane System Servicing or filling  Always shut OFF the engine while refueling. Do not smoke and do not operate other ignition sources while refueling. When the propane container is disconnected from the main supply hose and the P.O.L. connection, install the P.O.L. plastic cap that is attached to the container.

  • Page 105: Propane Use And Safety

    Section 7: Fuel & Propane System NOTE: Regulator appearance and type may vary by model. Single stage regulator Some models are equipped with a single stage regulator. Two stage regulator The two-stage regulator has the only moving components in the propane system. Its sole function is to reduce the pressure from the propane containers to a safe and consistent low operating pressure.

  • Page 106: Using The Propane System

    Section 7: Fuel & Propane System Apply the soapy solution to the outside of the gas piping fittings. If a leak is present, the soapy solution will “bubble” at the leak point. If a leak is indicated, shut off the propane system valve(s) and contact your dealer or qualified propane service representative immediately.

  • Page 107: Calculating Propane Gas Usage

    Section 7: Fuel & Propane System as the danger of asphyxiation is greater when the appliance is used for long periods of time. FAILURE TO COMPLY MAY RESULT IN DEATH OR SERIOUS INJURY. These warning labels are located in the cooking area to remind the user to provide an adequate supply of fresh air for combustion.
  • Page 108 Section 7: Fuel & Propane System Use care when fueling your motor fuel tanks and/ or propane containers. Make certain your propane tank is properly fastened in place. This label should be kept permanently affixed to your recreation vehicle. Refueling warning label Maintenance Record Table of Contents...

  • Page 109: Plumbing System

    Section 8: Plumbing System Plumbing System There are two different water systems in your recreation vehicle: The fresh water system consists of the fresh water holding tank, faucets and connections, water pump, outside shower assembly (if so equipped), water heater, tub/shower, and water purification system (if so equipped).
  • Page 110 Section 8: Plumbing System Operation Press only one tact switch at a time. As you push either the FRESH, BLK GREY1 or GREY2 switch, one or more LED lights will illuminate (from left to right) indicating the content level for that tank. When pushing the “BATT” switch, the LED lights illuminate from left (lowest) to right (highest) to indicate the estimated auxiliary battery condition.

  • Page 111: Fresh Water System

    Section 8: Plumbing System Fresh Water System All water contains contaminant and mineral particles that can cause fresh water system odors. Untreated well water is a major source of water system odors. The fresh water (potable water) system needs periodic sanitization and winterization to take care of all the components in the plumbing system to discourage the growth of bacteria and other organisms that can contaminate the water supply.

  • Page 112: To Replace Canister Filter Cartridge

    Section 8: Plumbing System Once activated, the water pump (also known as the demand pump) will self-prime, The pump is designed for intermittent use only. Using the pump and provide water. continuously or with high pressure will shorten the life of the pump and is not covered in your warranty.

  • Page 113: Draining The Fresh Water System

    Section 8: Plumbing System Clean the inside of the filter housing with mild detergent. Thoroughly rinse and wipe clean. Remove the O-ring from the groove in the housing and wipe clean. Recoat with petroleum jelly. Replace the O-ring in the groove, making sure it is properly seated. Install the new filter cartridge.

  • Page 114: Nautilus P3 Uni-Dock Utility Center

    Section 8: Plumbing System Open the “low point drains” by turning, then pulling the handles up. They are installed at the lowest point of the water lines. A label is placed on the outside of the RV to indicate where the drains are located.
  • Page 115 Section 8: Plumbing System The city water connection inlet is located in the Uni-Dock utility center. Use a non-toxic drinking water hose dedicated only to supplying fresh water. To prevent contamination, keep the non-toxic drinking water hose from coming into contact with the ground. Install the city water connection inlet cap when the fresh water connection is not being used.
  • Page 116 Section 8: Plumbing System (D) Red handle pointing up Connect the other end of the hose to a pressurized fresh water source (faucet or spigot). Turn the pressurized water source ON, the tank should begin filling. When water has reached the desired level, turn the pressurized water source OFF. DO NOT OVERFILL (Tank level can be viewed on the monitor panel inside the RV).
  • Page 117 Section 8: Plumbing System NOTE: To fill the fresh water tank without a pressurized water source, refer to SANITIZE (Siphon Fill) section, and use a container holding fresh potable water and a hose. Water will be drawn into the tank by the pump. There is no gravity fill inlet on the recreation vehicle.

  • Page 118: Sanitizing The Plumbing System

    Section 8: Plumbing System Leave the valves set on WINTERIZE setting. SANITIZING THE PLUMBING SYSTEM: When to sanitize: When your RV is new. At the beginning and end of each season. When the water system becomes contaminated or every three months of use. How to Sanitize Turn water heater power OFF (both electric &...
  • Page 119 Section 8: Plumbing System full. Disconnect the hose from utility center. After the recommended amount of sanitizing solution is in the tank make sure the water tank is full, the cartridge water filter (if so equipped) is bypassed or the filter is removed from the full system canister water filter (if so equipped), and power to water heater is turned OFF (both electric &...
  • Page 120 Section 8: Plumbing System 16. Drain the fresh water system again. If the RV has the full system canister water filter, remove the canister, reinstall the filter, and reattach the canister. 17. Refill the fresh water tank with fresh water again and when water heater is full of water, turn the water heater power ON.

  • Page 121: Winterizing The Plumbing System

    Section 8: Plumbing System Close all faucets including outside shower. Turn pump OFF. Drain the system again, but do not drain the water heater (Water heater power still OFF). Close low point drains and fresh water tank drain. Refill the fresh water tank with clean potable water. Use the city water fill connection inlet, and one of the two methods explained in Step 3.
  • Page 122 Section 8: Plumbing System Refer to Sanitizing the Plumbing System section for an explanation of docking station valve positioning and routing information. The preferred method to winterize your recreation vehicle is by using RV antifreeze in the plumbing system. It may be easier to winterize the RV with another person to assist you. ...
  • Page 123 Section 8: Plumbing System On full system canister water filters (if so equipped), remove the canister, take out the filter, and reattach the empty canister. Appliances (refrigerator, dishwasher or clothes washer) must be winterized. Refer to the appliance owner’s manual for additional information or contact your Dealer or Customer Service for assistance.

  • Page 124: Truma® Tankless Water Heater (If So Equipped)

    Section 8: Plumbing System De-winterize the macerator system: Emptying the black tanks in the spring will flush antifreeze out of the macerator system. Truma® Tankless Water Heater (If So Equipped) Your motor home may be equipped with a Truma® tankless water heater. The tankless water heater has no pilot light and supplies an unlimited supply of hot water on demand.
  • Page 125 Section 8: Plumbing System Opening the exterior water heater panel: Turn the locking knob, and open the exterior water heater panel to the first open position (A).To open the panel to the NOTE: The panel will only open enough to access the power switch on the inside.
  • Page 126 Section 8: Plumbing System Maintenance Inspect your water heater monthly and have it serviced at least once a year by the manufacturer’s recommended service technician. Contact your RV dealer, the manufacturer, or Customer Service. Pressure - Temperature Relief Valve  SCALDING INJURY-EXPLOSION Valve is not serviceable;...
  • Page 127 Section 8: Plumbing System Water heater should be OFF, water pump OFF, and fixtures open to relieve pressure on the plumbing system. DO NOT DRAIN WHEN APPLIANCE IS HOT OR UNDER PRESSURE. Open the water heater exterior door to the “service” position hanging by the straps. Open the drain chute by pushing up on the black button above the yellow label on the left side of the water heater (A).
  • Page 128 Section 8: Plumbing System plumbing bypass valves so no water or antifreeze will enter the water heater. Then winterize your RV waterlines with antifreeze as normal. (Refer to Winterizing the Plumbing System) NOTE: Using air pressure to blow out your Aqua Go water heater is NOT recommended and may damage the appliance.

  • Page 129: Outside Shower (If So Equipped)

    Section 8: Plumbing System 17. Turn the rotary control dial inside the RV to “CLEAN”. If decalcification does not start, make sure power to the water heater is turned ON. The yellow status LED will flash slowly (1 sec on, 1 sec off) during decalcification. ...

  • Page 130: Faucets

    Section 8: Plumbing System draining. After the water has been allowed to drain from the shower head, return it to the outside shower compartment. Any remaining water in the shower hose will drip or run out; this is not a leak but performs as intended. If you are dry camping, turn the water pump OFF.

  • Page 131: Black/Grey Water System And Tanks

    Section 8: Plumbing System The shower faucet includes a vacuum breaker for the shower. There are two purposes for this breaker: To prevent siphoning water through the hose from another fixture. To prevent water from being retained in the hose. The showerhead DOES NOT have a complete shut-off valve (the complete shut-off is at the faucet).

  • Page 132: Black/Grey Water Holding Tanks

    Section 8: Plumbing System roof and must be kept clear of obstructions to perform as intended. On some models, the vent pipe may be part of the drainage system referred to as a “wet vent” (water flows downward as air flows upward in the same pipe). Some models are equipped with a side vent system.

  • Page 133: Black / Gray Tank Drains W/Macerator System

    Section 8: Plumbing System Black / Gray Tank Drains w/Macerator System Macerator Pump System Your motor home is equipped with a macerator pump system used to discharge waste from the gray and black waste tank. The system has a 1-1/2-inch diameter flexible hose located beneath the utility center panel or in a separate hose storage compartment.

  • Page 134: Tank Heaters (If So Equipped)

    Section 8: Plumbing System Open the the gray drain valve T-handle. Turn the Macerator Power Switch ON. When tank is empty, turn the macerator power switch OFF. Close the gray tank drain valve T-handle. Unhook the dump connector, rinse it out and replace the hose and connector back into the storage compartment or under the utility center.
  • Page 135 Section 8: Plumbing System 44°F (7°C) and will turn OFF at 64°F (18°C). All of the heaters are controlled by a single ON/OFF switch. Typically, this red tank heater ON/OFF switch is located on the command center panel or in the bathroom.
  • Page 136 Section 8: Plumbing System always have four to six inches (10 - 15 cm) of water in the toilet. It is important to add enough water to prevent solid waste buildup. The following guidelines will help to prevent solid waste buildup. Sewage (black) tank preparation Release one to two quarts (1 or 2 liters) of water into the toilet bowl.

  • Page 137: Air Conditioner

    Section 9: Heating and Cooling Air Conditioner The air conditioning system is controlled by a thermostat. Cooled air enters the RV through the grill. Make sure you have sufficient power available before operating the air conditioner. Do not operate the air conditioner without the return air filter. Operating the system without the filter allows the lint and dirt that is normally stopped by the filter to accumulate on the cooling coil of the air conditioner.

  • Page 138: Furnace

    Section 9: Heating and Cooling rain sensor that will close the vent automatically when it rains. The rain sensor can be turned on/off by holding the DOWN button for 3 seconds. Furnace The furnace installed in your recreation vehicle is controlled by a 12-volt DC thermostat. Depending on your model, there may be up to two thermostats enabling you to control the temperature to your comfort level.

  • Page 139: Microwave

    Section 10: Appliances Microwave  To prevent damage, remove the turntable from the microwave when traveling. Make sure you are connected to a 120-volt power source.  Never use the microwave cavity for storage. The microwave cavity should always be empty when not in use. For details on operation, cleaning and safety information, refer to the manufacturer’s user guide.

  • Page 140: Cooktops; Range & Oven (If So Equipped)

    Section 10: Appliances Cooking With Propane (If So Equipped) See the Propane System Section for important safety instructions. Refer to the manufacturer’s owner’s manual for detailed operating and safety instructions for all propane appliances. Cooktops; Range & Oven (if so equipped) For detailed operating and safety information, refer to the manufacturer’s user guide.

  • Page 141: Gas Drop-In Cooktops (If So Equipped)

    Section 10: Appliances  Do not use aluminum foil on the electric range cooktop, as this material will damage the cooktop surface if it melts. Do not use aluminum foil under any circumstances on the electric range cooktop. Gas Drop-In Cooktops (if so equipped) Depending on your model, it may be equipped with either a 2 burner or 3 burner cooktop.

  • Page 142: Refrigerator

    Section 10: Appliances  Whenever the stove in the RV is being used: The range hood MUST be turned on, and the inner flap MUST be unsnapped and free to move. Failure to do so can create an asphyxiation hazard by restricting air flow to this vent. Refrigerator The refrigerator is not intended for quick freezing or cooling.

  • Page 143: Cleaning The Interior

    Section 10: Appliances  Converter output (12VDC) is not intended for normal operation of the 3-way refrigerator. When the camping trailer is parked and the power cord is plugged in, set the 3-way refrigerator to “AC power.” The “DC mode” is to be used only when traveling and will pull power from the auxiliary battery charge line (if so equipped).
  • Page 144 Section 10: Appliances steel cleaner. A spray-on stainless steel cleaner works best. IMPORTANT: Do not allow the Stainless Steel Cleaner and Polish to come into contact with any plastic parts such as the trim pieces, dispenser covers or door gaskets. If unintentional contact does occur, clean plastic part with a sponge and mild detergent in warm water.

  • Page 145: Hdtv Antenna/Satellite System(S)

    Section 11: Electronics HDTV Antenna/Satellite System(s) Your recreation vehicle may be equipped with an exterior amplified high definition TV antenna. The antenna comes equipped with a signal meter and a power injector to aid in receiving the strongest possible signal when tuning in HDTV stations.

  • Page 146: Exterior Entertainment Center (If So Equipped)

    Section 11: Electronics Antenna Power Supply (If So Equipped) For good station reception, the antenna power supply must be turned ON to view local television stations. Turning the antenna power supply ON sends 12-volt DC through the cable to the TV roof antenna. The voltage energizes the transistors in the antenna head amplifier.

  • Page 147: Cleaning The Interior

    Section 12: Interior Cleaning The Interior To keep the value of your recreation vehicle, perform regular maintenance using the proper materials and procedures. Using the wrong cleaner may result in damage to the surfaces in your vehicle. Check with the manufacturer’s information for the recommended cleaning agent.

  • Page 148: Cabinetry & Tables

    Section 12: Interior Day/Night Shades: Clean with a mild cleaning solution using a sponge or paper towel. Wipe down with water after cleaning and dry thoroughly before raising the shade. Do not use spot remover, household cleaners or detergents to remove soiled spots, as these may cause damage to fabric or loss of color from fading.

  • Page 149: Abs Plastics

    Section 12: Interior ABS Plastics Dust and wipe clean with soft, damp cloth or chamois, wiping gently. Do not use gritty or abrasive particle soaps or scouring compound to clean ABS plastic. Avoid using “citrus” or biodegradable cleaners that contain “D-Limonene” as they may damage plastic materials. Sofa &...

  • Page 150: Dream Dinette Unlocked

    Section 12: Interior Trifold Sofa The Trifold Sofa offers very similar features to the traditional hide-a-bed. The following illustrations detail converting the sofa into a bed. Booth Dinette (If So Equipped) The dinette is designed to seat up to four adults. Depending on your model, there may be a storage area in the dinette bench.

  • Page 151: Pantry Or Hutch (If So Equipped)

    Section 12: Interior free standing dinette chairs be fastened securely at the dinette table, and the folding chairs be secured in a closet or storage area  Do not allow occupants to occupy the free standing dinette chairs while the motor home is in transit.

  • Page 152: Flooring

    Section 12: Interior Solid surface countertops (if so equipped) Soapy water, ammonia based cleaners (not window cleaners as they can leave a waxy build up that may dull the surface) or commercially available solid surface cleaners will remove most dirt and residue from all types of finishes. A damp cloth followed by a dry towel will remove watermarks.

  • Page 153: Privacy Drape Installation

    Section 12: Interior Privacy Drape Installation Starting on the driver’s side, attach the black plastic hook to the loop on the wall (behind the driver’s seat). Make sure the Velcro® on the drape is facing the motorhome windshield. Pull the drape towards the windshield and past the driver’s side sun visor. Open the sun visor against the windshield to hold the drape in place.

  • Page 154: Fig 1: Belt Interlock Latched

    Section 12: Interior  There should be no people, pets or objects on or below the bunk while raising or lowering it. Failure to comply may result in serious injury or property damage. With vehicle in transit, the bunk should always be in the raised storage position with the interlock belt latched.

  • Page 155: Cleaning The Exterior

    Section 13: Exterior Cleaning The Exterior To protect your recreation vehicle’s exterior finish, wash it often and thoroughly. For recreation vehicles with painted exterior graphics: If desired you may wash and wax your vehicle 60 days after purchase. The exterior paint does need time to cure before any wax is applied to the exterior surface.
  • Page 156 Section 13: Exterior stains. They can be dissolved using ammonia based glass cleaner, warm soapy water and a little “elbow grease”. Once again, after removing stubborn stains immediately rinse with clean water. Drying the recreation vehicle is just as important as washing your vehicle. Tap and well water contain many chemicals that could water stain your vehicle’s finish.

  • Page 157: Frame

    Section 13: Exterior  Do not use waxes containing high-abrasive compounds. Such waxes remove rust and stains effectively from the paint work, but they are also harmful to the luster of the painted surface since they scrape off the coating. Further, they are detrimental to glossy surfaces, such as the grille, garnish, moldings, etc.

  • Page 158: Exterior Roof & Sidewall Vents

    Section 13: Exterior the alignment inspected periodically to maintain vehicle steering performance and prevent uneven tire wear as part of your normal maintenance. NOTE: Always have the alignment checked and adjusted by a qualified shop with the proper equipment to handle heavy vehicles. NOTE: A road test by the dealer should be included as part of the pre-delivery inspection.
  • Page 159 Section 13: Exterior  If your recreation vehicle is equipped with a roof ladder, do not leave items attached to it while traveling. The ladder weight capacity should not be exceeded (see ladder capacity label). DO NOT exceed this weight limit.
  • Page 160 Section 13: Exterior  To check the exterior sidewall sealants, use a stepladder placed safely alongside the vehicle. Do not prop a ladder against the body of the motor home as it may damage the exterior finish Maintenance Record Table of Contents...

  • Page 161: Travel Checklist

    Section 14: Travel/Camping/Storage Checklists Travel Checklist Following is a preliminary list of items that need to be checked before leaving your home or campsite. This is a general list, which you may want to customize as you determine your own needs. Refer to your Chassis Guide for information on chassis pre-trip inspections and maintenance.
  • Page 162 Section 14: Travel/Camping/Storage Checklists Turn off propane tanks (if so equipped). Empty black and gray holding tank, rinse as needed. Retract any awnings and secure them for transport. Close all the roof vents. Close windows & latch blinds. Disconnect the cable TV and phone hookups and lower the TV antenna. Turn off the interior lights, water heater, furnace and water pump.
  • Page 163 Section 14: Travel/Camping/Storage Checklists Turn OFF the motor home 12-volt battery disconnect switch. Turn OFF the inverter mode at remote. Disconnect the batteries to prevent battery discharge. Remove all perishables from the refrigerator/freezer. Defrost, wash and dry the interior of the refrigerator/freezer and prop (or block) the doors open so air can circulate and prevent mildew.
  • Page 164 Section 14: Travel/Camping/Storage Checklists Notes: Maintenance Record Table of Contents...

  • Page 165: Featured Components Quick Reference Chart

    Your recreation vehicle may be equipped with some of the items listed below. This is a partial listing and it is not intended to cover all components. All information is the latest available at the time of publication. Jayco reserves the right to change any of the following information without notice.
  • Page 166 Section 15: Additional Information Toilet Thetford Corp. www.thetford.com Water Heater, Tank DSI Atwood Greenbrier www.atwoodmobile.com Water Heater, Tankless Girard Systems www.greenrvproducts.com Shurflo East www.shurflo.com Water Pump, 12V Maintenance Record Table of Contents...

  • Page 167: Vehicle Maintenance Record

    Section 15: Additional Information Vehicle Maintenance Record Make: Model: Model Year: Vehicle Serial#: Engine: Engine Serial#: Service Performed Mileage Work Performed Notes Date Maintenance Record Table of Contents...
  • Page 168 Section 15: Additional Information Notes: Maintenance Record Table of Contents...
  • Page 169 Section 15: Additional Information Jayco Ownership Notification Fax Form To: (800) 825-7876 ATTENTION! Federal record keeping laws require that we maintain a file of owners of our product. Your cooperation in filling out this from will be appreciated. □ □...

Table of Contents