Jayco Hummingbird 2018 Owner's Manual
  1. Manuals
  2. Brands
  3. Jayco Manuals
  4. Motorhomes
  5. Hummingbird 2018
  6. Owner's manual

Jayco Hummingbird 2018 Owner's Manual

Towables
Hide thumbs
Table of Contents

Advertisement

Quick Links

2018
Towables
Owner's Manual
PRINTED ON RECYCLED PAPER
0283457.2018

Advertisement

Table of Contents
loading

Related Manuals for Jayco Hummingbird 2018

Summary of Contents for Jayco Hummingbird 2018

  • Page 1 2018 Towables Owner’s Manual PRINTED ON RECYCLED PAPER 0283457.2018...
  • Page 3 44,683 people. We’re proud of our results, and we know those numbers show that a little initiative can go a long way. The Jayco EcoAdvantage is our way of making sure endless generations can enjoy the Great Outdoors.

  • Page 5: Table Of Contents

    Change Of Address/Ownership Suggestions For Obtaining Service Obtaining Service For Separately Warranted Items Obtaining Service At Our Customer Service Facility Parts & Accessories Notice To Jayco Dealers Section 2: Occupant Safety Secondary Means of Escape (Exit Window) Exit Window Label Fire Safety...
  • Page 6 Table of Contents Stabilizer Jacks Manual Stabilizer Jacks (if so equipped) Emergency Stopping Emergency Towing Wheel Lugs Electric Stabilizer Jacks (if so equipped) Tires Changing A Tire Spare Tire Carrier (if so equipped) Bracket Mount Travel Position Hoist Mount Travel Position Crank Access Port Bumper Mount Bumper Mount...
  • Page 7 Table of Contents Replacing A Fuse 12-Volt DC Outlet Dry Camping Replacement and Maintenance Battery Isolator For Your Tow Vehicle (customer supplied) Battery Disconnect Switch (if so equipped) Load Center 120-Volt Circuit Breakers Typical Load Center Panel Battery Disconnect Switches Approximate Electrical Load Ratings 120-Volt (30 AMP) AC System (if so equipped) 30-AMP Power Cord (if so equipped)
  • Page 8 Table of Contents Operation Fresh Water System Water Pressure Regulator (customer supplied) Fresh Water Holding Tank 12-Volt Water Pump & Switch Fresh Water Connections City Water Fill with City Water Connection label Potable Water Label Gravity Water Fill Draining The Fresh Water System Sanitizing/Winterizing The Plumbing System Low Point Drains Exterior Fresh Water Drain...
  • Page 9 Table of Contents Quick Connect Coupler Gas Grill & Mounting Bracket on Support Rail Range Hood Vent Refrigerator Cleaning The Interior Cleaning The Exterior Water Heater – See Plumbing Section Section 11: Electronics HDTV Antenna/Satellite System(s) HDTV Antenna (if so equipped) Antenna Power Supply (if so equipped) Satellite (if so equipped) Antenna Power Supply...
  • Page 11 WARNING: Read all instructions in this manual and component manufacturer supplied information before using your RV. This manual has been provided by your recreational vehicle manufacturer for the sole purpose of providing instructions concerning the operation and maintenance of this recreational vehicle.
  • Page 12 Maintenance Record Table of Contents...
  • Page 13 Canada may differ to conform to Canadian Codes. Dealer Responsibility At the time of sale of the new recreation vehicle, your Jayco dealer is expected to: Deliver your recreation vehicle in the best condition possible. Your recreation vehicle must pass the dealer’s pre-delivery inspection (PDI), including all systems tests.
  • Page 14 (or any effect of the alterations) to any of the parts, components, systems or assemblies installed by Jayco. Jayco is not responsible for the safety or quality of design features, materials or workmanship of any alterations by such suppliers.

  • Page 15: About This Manual

    Canada. In addition, the club offers a variety of local and regional activities throughout the year. By belonging to the Jayco Travel Club, you will find new ways to enjoy your RV and make friends all across the country.

  • Page 16: Warranty Packet

    Section 1: Warranty & Service in this manual creates any warranty, either expressed or implied, nor does it cover every possible detail of equipment, standard or option, installed on or in your recreation vehicle. Information, illustrations and specifications in this manual reflect the most current available at the time of publication approval, are subject to change and not intended to indicate actual size.

  • Page 17: Reporting Safety Defects

    Section 1: Warranty & Service  Indicates an imminently hazardous situation that, if not avoided, will result in death or serious injury. This alert information is limited to the most extreme situations.  Indicates a potentially hazardous situation that, if not avoided, may result in death or serious injury.
  • Page 18 Section 1: Warranty & Service Customer Responsibility It is important you read and understand all instructions and precautions before operating the recreation vehicle. Even if you are an experienced RV’er we encourage you to thoroughly read this Owner’s Manual, as well as the information contained in your Warranty Packet and Chassis Guide (motorized only).
  • Page 19 Section 1: Warranty & Service Inspect the work performed… Finally, check out the service or repair job when you pick up your vehicle. Notify the dealer’s service personnel immediately of any dissatisfaction. If you cannot return the vehicle immediately for repair, make an appointment as soon as possible.

  • Page 20: Towable Limited Warranty

    RV is delivered to the first retail purchaser by an independent, authorized dealer of Jayco, or, if the dealer places the vehicle in service prior to retail sale, on the date the RV is first placed in such service. In the event that a substantial defect in material or workmanship, attributable to Jayco, is found to exist during the warranty period, it will be repaired or replaced, at Jayco’s option, without charge to the RV owner, in accordance with...
  • Page 21 RV to the service center on the specified appointment date. If you need assistance you may contact Jayco, at 903 S. Main Street, P.O. Box 460, Middlebury, Indiana 46540, Attn: Customer Service, (574) 825-5861, (800) 283- 8267 or www.jayco.com.
  • Page 22 Certain things completely discharge Jayco from any obligation under this warranty and void it. By way of example, the following shall discharge Jayco from any express or implied warranty obligation to repair or replace any defect that results from: any rental or other commercial use or purchase of the RV (as defined in this warranty), any RV sold outside of, or used outside of, the United States, U.S.
  • Page 23 Jayco, or any agent of Jayco, shall be interpreted as an extension of the warranty period or this limitation period. Some states do not allow a reduction in the statute of limitations, so this reduction may not apply to you.

  • Page 24: Jayco Towable Rental Limited Warranty

    Limited Warranty will not apply to this RV. The Towable Limited Rental Warranty applies in that situation. If, on the other hand, the Jayco dealer sells this RV to a retail customer then the rental warranty would not be applicable. The rental warranty does not apply to retail consumers.
  • Page 25 Pay any freight or transportation costs, import duties, fees and all incidental expenses associated with obtaining warranty service. If you need assistance you may contact Jayco, at 903 S. Main Street, P. O. Box 460, Middlebury, Indiana, 46540, Attn: Customer Service (574) 825-5861, (800) 283-8267 or www.jayco.com.
  • Page 26 You must inspect the RV for this type of damage when you take delivery from Jayco. If you find any such defect or damage you must notify Jayco within three (3) days of delivery of the RV to you to have these items covered by this limited warranty and to have work performed on the items covered by this limited warranty.
  • Page 27 Jayco, or any agent of Jayco, shall be interpreted as an extension of the warranty or this limitation period. Some states do not allow a reduction in the statute of limitations, so this reduction may not apply to you.
  • Page 28 Section 1: Warranty & Service Notes: Maintenance Record Table of Contents...
  • Page 29 Section 2: Occupant Safety Secondary Means of Escape (Exit Window) Your recreation vehicle has been equipped with a window(s) that serves as a secondary means of escape. The window(s) will allow a quick exit from the vehicle during an emergency if access to the main entrance door is not available.

  • Page 30: Fire Safety

    Section 2: Occupant Safety Fire Safety If a fire does start, follow these basic safety rules: Call 911 and evacuate the vehicle immediately. After everyone is accounted for, check the fire to see if you can attempt to put it out. If it is large, or the fire is fuel-fed, get clear of the vehicle and have the Fire Department handle the emergency.

  • Page 31: Smoke Alarm

    Section 2: Occupant Safety  Do not turn the electrical power back on or plug in any appliances after the use of a fire extinguisher. Please refer to the fire extinguisher’s user manual for further instructions on maintenance and clean up. Smoke Alarm The smoke alarm will only work properly if it is operational and maintained.
  • Page 32 Section 2: Occupant Safety To test, stand at arm’s length from the smoke alarm as the alarm horn is loud and may be harmful to your hearing. The test button will accurately test all functions. Never use an open flame to test the smoke alarm. Do not remove the warning label located near the smoke alarm from your recreation vehicle: Maintenance...
  • Page 33 Section 2: Occupant Safety The alarm is directly wired to the 12-volt electrical system, with continuous power being supplied by the recreational vehicle batteries. There is no 9-volt battery power supply. As a result, the alarm is always drawing a small amount of current from the recreation vehicle batteries.
  • Page 34 Section 2: Occupant Safety What you should do if the alarm sounds  Actuation of this detector indicates the presence of carbon monoxide which can kill you. Never turn the 12-volt battery disconnect control to the off position and disconnect the battery cable to silence an alarm. The alarm will automatically sense when the level of carbon monoxide in the air reaches below dangerous levels.
  • Page 35 Section 2: Occupant Safety Testing the combination carbon monoxide/propane alarm  Test the alarm operation after the RV has been in storage, before each trip and at least once per week during use. The TEST/RESET button tests all ELECTRICAL functions of the alarm. The TEST/Mute switch is located on the front of the alarm.

  • Page 36: Cold Weather Usage

    Section 2: Occupant Safety  Continuous or permanent living in your recreation vehicle may affect your warranty coverage and may void the “Limited Warranty” applicable to your vehicle. Cold Weather Usage When used in freezing or below freezing temperatures, the precautions should be taken: Fresh water and drainage systems - preparations to avoid freeze-ups.

  • Page 37: Tow Vehicle

    Section 3: Pre-Travel Information Tow Vehicle If you plan to tow your recreation vehicle with a tow vehicle you already own, or if you plan to purchase a new one, make sure the Gross Vehicle Weight Rating (GVWR) or your recreation vehicle does not exceed your tow vehicles towing rating.
  • Page 38 Section 3: Pre-Travel Information OCCC Label (Occupant & Cargo Carrying Capacity: The upper portion of this yellow label is federally required and includes the maximum Occupant & Cargo Carrying Capacity that may be placed in or on the trailer as it was manufactured and weighed before leaving the factory.
  • Page 39 Section 3: Pre-Travel Information Loading Your Recreation Vehicle  Never load the RV in excess of the GAWR for either axle. Overloading your RV may result in adverse handling characteristics and damage to the RV. DO NOT EXCEED YOUR GVWR! This means you should weigh your RV as loaded for your normal travel to determine the actual weight.

  • Page 40: Rear Bumper

    Section 3: Pre-Travel Information Rear Bumper  Do not add items to the recreation vehicle rear bumper. Add-on items will eventually damage your bumper. Damage caused by such aftermarket equipment installation or improper loading voids the Towable Limited Warranty. The rear bumper of your RV is not designed to carry cargo. Items that extend beyond the bumper OR weigh over 100 lbs.
  • Page 41  Using an oversized or undersized hitch can cause damage to the RV frame. Jayco cannot be responsible for the tow vehicle suspension system. The final ball height after the tow vehicle/travel trailer combination is completely hooked up is a factor that must be considered. To avoid overloading your trailer axles and minimize possible handling difficulties, your trailer should be level when hooked to your tow vehicle.
  • Page 42 Section 3: Pre-Travel Information Remove the dolly wheel or platform and retract the tongue jack to its maximum height. Attach the breakaway switch cable to the tow vehicle. 10. Attach the safety chains. 11. Plug in your wire harness/connector plug from the tow vehicle to the travel trailer. 12.
  • Page 43 Section 3: Pre-Travel Information Crisscross the left safety chain under the coupler and attach to the right mounting slot in the trailer hitch; repeat with the right safety chain. Slack for each length should be the same but not more than necessary to permit the vehicle to turn at its minimum radius, but tight enough not to drag on the ground.
  • Page 44 Section 3: Pre-Travel Information The connector plug may build up corrosion with extended use and should be cleaned periodically to insure good electrical contact. Make sure the connector plug is kept clean and protected from road elements as you travel. Weighing Your Tow Vehicle &...
  • Page 45 Section 3: Pre-Travel Information To determine the wheel position weight: Pull the RV onto the scale so only one tire is on the scale. Record the weight. Your RV must remain as level as possible on the scale (even though an axle or side is not physically on the scale).
  • Page 46 Section 3: Pre-Travel Information Notes: Maintenance Record Table of Contents...

  • Page 47: Towing

    Section 4: Vehicle Operation Towing  Your RV braking system is rated for operation at GVWR not GCWR. Whenever possible, do not travel with waste in the holding tanks. Liquid or debris in the holding tank(s) may affect the towing characteristics and may result in property damage or personal injury.

  • Page 48: Electric Brakes

    Section 4: Vehicle Operation Driving through water deep enough to wet the brakes may affect stopping distance or cause the vehicle to pull to one side. Check the RV’s brake operation in a safe area to be sure they have not been affected. Never operate any vehicle if a difference in braking efficiency is noticeable.

  • Page 49: Towing Behind Your Rv

    Towing Behind Your RV  If you do not have a Jayco factory installed hitch receiver, towing items behind your Jayco RV, or overloading the rear, will void the warranty and may result in: damage to the RV or add-on items, towing difficulties, property damage and/or personal injury.

  • Page 50: Entrance Door Step(S)

    Section 4: Vehicle Operation Entrance Door Step(s) Make sure your entrance step is fully extended before exiting the vehicle, and retracted prior to towing. Lubricating the step mechanism Carefully clean the area around the pivot points (the rivets involved in the motion of the mechanism). Lubricate these pivot points with an automotive grade, non-staining lubricant every 30 to 60 days.

  • Page 51: Campsite Hook-Up

    Section 4: Vehicle Operation Depending on your model, you may also have a pre-installed power switch for the camera located in an exterior compartment. (battery storage or utility center) To install a backup camera, refer to the manufacturers installation guide along with the installation supplement provided in the warranty packet.

  • Page 52: Emergency Stopping

    Section 4: Vehicle Operation Electric Stabilizer Jacks (if so equipped) Control switches for the stabilizer jacks are typically located on the (door) side of the unit above the stabilizer jack(s). To lower each jack, press the control switch until each leg contacts the ground and stabilizes the unit.
  • Page 53 Section 4: Vehicle Operation Check and re-torque after the first 10, 25 and 50 miles (16, 40 and 80 kilometers). Thereafter, check and maintain the torque according to the listed torque values Because of the importance of having proper torque on the wheel lug nuts, you should always have the wheels mounted and properly torqued by a qualified technician using the proper tools.

  • Page 54: Tires

    Section 4: Vehicle Operation  Check and tighten wheel lug nuts regularly to make sure they did not loosen during travel. Wheel lug nuts must be applied and maintained at the proper torque levels to prevent loose wheels, broken studs and possible separation of the wheel(s) from your recreation vehicle.
  • Page 55 Section 4: Vehicle Operation Tire Pressure  Failure to follow proper inflation guidelines may result in tire failure, which, under certain circumstances can cause loss of vehicle control or accidents that may result in property damage, bodily injury and/or death. You must follow the manufacturer’s inflation guidelines for maximum load capacity;...

  • Page 56: Changing A Tire

    Section 4: Vehicle Operation Changing A Tire  Do not use the stabilizer jacks to support the recreational vehicle while under the vehicle or changing tires. The stabilizer jacks are designed as a stabilizing system only. Do not use the stabilizer jacks as a jack or in conjunction with a jack.

  • Page 57: Hoist Mount Travel Position

    Section 4: Vehicle Operation Spare Tire Carrier (if so equipped) If your recreational vehicle is equipped with a spare tire, it will either be mounted under the unit (hoist) or on the rear bumper. Hoist Mount  DO NOT exceed the maximum load capacities of 100 lbs. for the hoist. DO NOT use air driven guns or impact wrenches to lift the spare tire to the travel position.
  • Page 58 Section 4: Vehicle Operation Securing the spare tire To secure the spare tire in the travel position, put the steel hoist lift support located on the end of the cable through the rim of the tire. The hoist lift support clips need to seat inside the center hole of the tire rim.

  • Page 59: Setting Up Your Recreation Vehicle

    Section 4: Vehicle Operation Setting Up Your Recreation Vehicle Position the RV as desired. Level the RV (side-to-side). Leveling your recreation vehicle is important as the water drainage systems are designed with proper slope and must be level for proper operation, and the appliances perform best when level.

  • Page 60: Power Awnings (If So Equipped)

    Section 4: Vehicle Operation Your recreation vehicle may include one or more of the following options: Power window awning Slide out awnings Power awning over entrance door Power switches to operate the awnings are typically found in the control panel above the entrance door.
  • Page 61 Section 4: Vehicle Operation Adjusting the Awning Pitch  Do not set the individual arm pitch at more than three (3) positions different between the left and right arms. Damage to the arms and the canopy can occur if the awning is retracted when the arms are set at more than three (3) positions difference.
  • Page 62 Section 4: Vehicle Operation Refer to the manufacturer’s user guide for detailed operating and safety information. Emergency Operation If power to the vehicle is not available, the awning can be retracted by jumping the motor using a 10VDC – 14VDC power source such as a cordless drill battery or car battery. Remove the front cover (the cover snaps onto the rear cover).
  • Page 63 Section 4: Vehicle Operation NOTE: If the awning is equipped with the Direct Response system, this procedure is not applicable. See the manufacturer’s owner’s manual for additional information. Locate and separate the quick disconnects located in the motor arm channel. Position the wires from the motor on the outside of the channel.
  • Page 64 Section 4: Vehicle Operation Notes: Maintenance Record Table of Contents...

  • Page 65: Electric Slide Room(S) (If So Equipped)

    Section 5: Slideout Systems Electric Slide Room(s) (if so equipped) The mechanical components of the slide out are gear driven. Electric powered slideout room systems have a manual override to allow you to extend or retract the slideout room(s) in case of a power loss.

  • Page 66: General Slideout Troubleshooting Checklist

    Section 5: Slideout Systems Operating the switch after the room is fully extended or retracted may damage the switch and motor. After the slideout is extended, visually inspect the slideout and the surrounding area to make sure the slideout has extended properly and has adequate clearance from any outside obstructions.
  • Page 67 Section 5: Slideout Systems NOTE: For long-term storage it is recommend the room be closed (retracted). Trouble shooting the flush floor slideout Refer to the general troubleshooting check list before proceeding. NOTE: Install transit bars (if so equipped) on the slideout room during storage and transportation.

  • Page 68: Schwintek In-Wall Slideout System

    Section 5: Slideout Systems Schwintek In-Wall Slideout System The in-wall slideout system requires no maintenance or adjustments. This system has two vertical columns with a drive motor located at the top of each column. The right and left motors are synchronized by a circuit board. Schwintek slideouts are typically used on both towables and motor homes.
  • Page 69 Section 5: Slideout Systems Maintenance This slideout system requires very little maintenance. It contains a pre-lubed bearing that is lubricated when the room is moved in and out. Do not spray oil or grease on the rails while the room is extended. Trouble shooting the in-wall slideout system Checking Fuses: The in-wall slide requires a minimum 30-amp fuse.
  • Page 70 Section 5: Slideout Systems The malfunctioning controller should have a flashing red LED indicating a halt signal fault (will flash 8 or 9 times). Press the “mode button” six times quickly, then press a seventh time and hold for approximately 5 seconds. The red and green LED’s will flash indicating you are in override mode.

  • Page 71: Error Codes

    Section 5: Slideout Systems Bend back the wipe seal and visually locate the motor (Fig. 4). Pull the motor up until it disengages (about 1/2 inch). Repeat this process for both sides of the slide room. 10. Physically push/ pull the room back into the opening; keep both sides relatively even. 11.

  • Page 72: Norco Slideout Manual Operation

    Section 5: Slideout Systems If the room will not activate, generally there is no 12V power to the drive motor. The motor is equipped with a hex drive override shaft. This drive can be activated using an electric drill and the flexible shaft provided with each unit (or use a ratchet to actuate the motor) to pull the room in or out.

  • Page 73: Power Gear Slideout System

    Section 5: Slideout Systems Power Gear Slideout System Manual Override - The slideout system is equipped with a manual override that allows you to extend or retract the room in the event of a loss of power.  Always disconnect battery from system prior to manually operating system.
  • Page 74 Section 5: Slideout Systems The room is now free to move. Using either a 5/8” or 3/4” wrench or socket, crank the room either in or out completely. If the slideout system is supplied with a gearbox override (optional), use the crank handle to move the room.

  • Page 75: Operating The Slideout

    Section 5: Slideout Systems Operating the Slideout The slideout will not function until the stops are properly set or faults are cleared. A solid “ON” GREEN LED indicates room movement. The RED LED indicates a fault or a problem with the system. (Refer to the Fault Diagnostics / Troubleshooting).

  • Page 76: Preventative Maintenance

    Section 5: Slideout Systems NOTE: For MAJOR faults, the control must be overridden by follow- ing the EMERGENCY RETRACT MODE in the OVERRIDE MODES section. Fault Codes Fault Fault Type Description Possible Cause Possible Solution Code -Stops have not been set Steps need to be programmed by an Major Stops not programmed...
  • Page 77 Section 5: Slideout Systems NOTE: During the override procedure, the unit will exit this mode if the room has not been moved for two (2) minutes or if a fault is detected during room movement. The Fault Code (RED) and Room or Lock Movement (GREEN) LEDs will flash rapidly for 10 seconds to indicate the override procedure failed.
  • Page 78 Section 5: Slideout Systems Manually Retract Room with Ratchet & Socket: If the power is lost to the slideout motor(s) or the override mode above will not work, the room may be manually retracted using a ratchet and socket attached to the end of the coupler (Fig 11).
  • Page 79 Section 5: Slideout Systems Manual Override Procedure: The system has been equipped with 3/4” hex override couplers located on the drive component of the system. Due to the size and weight of some rooms, assistance may be needed to push the room in. Use the following steps to mechanically operate the room: Locate the ABS motor access cover for the slideout.
  • Page 80 Section 5: Slideout Systems The spring lock lever is a thin metal arm with a slight bend at the end, which will hold the brake lever in the released position. The brake lever is the heavier thicker metal arm with the hole in the end.

  • Page 81: The Electrical System

    Section 6: Electrical System The Electrical System The RV electrical system is comprised of two independent electrical systems. One operates off of 12-volt DC power and the other off of 120-volt 60hz AC power. All installations have been made in compliance with industry standards applicable on the date of manufacture. Because the electrical equipment and associated circuitry are engineered into a dedicated system specific to your RV, do not make unauthorized changes or add fixed appliances to it.

  • Page 82: Command Center

    Section 6: Electrical System Command Center The command center is typically located inside the entrance door or in the living area of the RV, and contains switches and controls for various electrical functions. Command center applications, configurations and components will vary by model. Command Center Panel or Command Center Panel with Switch Modules Items found on these panels may include:...
  • Page 83 Section 6: Electrical System GFCI Receptacle There is a ground fault current interrupter (GFCI) engineered into the electrical system. It is designed to reduce the possible injury caused by electric shock. The GFCI will not protect against short circuits or circuit overloads. Test all GFCI receptacles monthly Push in the GFCI “TEST”...

  • Page 84: Testing The Campsite Power Connection

    Section 6: Electrical System Testing The Campsite Power Connection The campsite 120-volt power receptacle(s) should always be tested for proper functionality prior to plugging the recreation vehicle shore power cord into it. Campsite 120-volt power receptacles can be tested using a digital multimeter or a dedicated circuit analyzer.

  • Page 85: Connecting The Power Cord

    Section 6: Electrical System Connecting The Power Cord Always test the external power source (i.e., the campsite power receptacle or electrical box) with a ground monitor before connecting your power cord to it. If the ground monitor indicates ‘reverse polarity’ or an ‘open ground’ DO NOT connect the power cord. To help prevent power surges from damaging the connected loads, please follow these instructions when hooking up to the external power source: Turn “off”...

  • Page 86: Converter With Charge Wizard (If So Equipped)

    Section 6: Electrical System  It is important that the fluid level of any connected batteries be checked on a regular basis. All batteries will “gas” and lose some fluid when continuously connected to any charging source (does not apply to “gel-cell” batteries). Before checking for converter output voltage, the battery cables must be disconnected at the battery.

  • Page 87: Volt Dc System

    Section 6: Electrical System NORMAL MODE: Green LED flashes once per second; battery is between 50% and 90% charged. Green LED will flash 2-3 times per second; battery is 90% charged. Output voltage is 13.6VDC and the converter is safely completing the charge of the battery.

  • Page 88: Auxiliary Battery (Customer Supplied)

    Section 6: Electrical System Replacing A Fuse Before replacing a fuse, always turn off the electrical components protected by it. Disconnect the shore power cord. Turn “off” the inverter (if so equipped). Disconnect the house or auxiliary batteries main negative battery cable. Remove the fuse panel cover to check fuses.

  • Page 89: Dry Camping

    Section 6: Electrical System Dry Camping The auxiliary battery should be fully charged prior to dry camping. If the auxiliary battery is not being recharged and power is being drawn from it, it will eventually discharge. A battery will discharge at a faster rate as its energy level becomes depleted. Plan your electrical usage accordingly.

  • Page 90: Load Center

    Section 6: Electrical System Rotating Dial Disconnect Switch When this switch is ON, there will be a green area showing a “1” along the top of the switch. To turn the switch OFF, turn it counter-clockwise until you see the red area along the left side of the switch showing a “0”...
  • Page 91 Section 6: Electrical System NOTE: Load Centers may not always include a main circuit breaker.  Circuit breakers and fuses will not offer complete protection of the electrical system in the event of power surge or voltage spike. Replacement Only replace circuit breakers with those of the same specified type, voltage, and current rating.
  • Page 92 Section 6: Electrical System Approximate Electrical Load Ratings 12 Volt System Exterior Entertainment Center 5-7 AMPS 1.5 AMPS Furnace 12.0 AMPS Generator Start 95.0 AMPS* Illuminated Switch .125 AMP Inverter variable Leveling System 95.0 AMPS* LP Detector .125 AMP Light; Halogen 1.7 AMPS Light;...

  • Page 93: Volt (30 Amp) Ac System (If So Equipped)

    Section 6: Electrical System 120-Volt (30 AMP) AC System (if so equipped) The 30 amp 120-volt 60hz AC electrical system.is designed to operate on 1 leg of 120-volt power at a maximum current flow of 30 amperes. Exposure to voltages higher or lower than a nominal 120-volts will damage or shorten the service life of the electrical system and appliances.

  • Page 94: Solar Prep (If So Equipped)

    Section 6: Electrical System The shore power cord is designed to continuously carry the 30-amp current flow required to power each leg of the electrical system. It also creates a critical ground connection between the vehicle electrical system and the campground shore power receptacle. Always test the external power source (i.e., the campsite power receptacle or electrical box) with a ground monitor before connecting your power cord to it.

  • Page 95: Exhaust Gas Fumes

    Section 7: Fuel & Propane System Exhaust Gas Fumes  Avoid inhaling exhaust gases as they contain carbon monoxide, which is a potentially toxic gas that is colorless and odorless. If you are in a recreation vehicle with either a nearby tow vehicle engine running or the generator (if so equipped) running there is a potential for exhaust fumes to filter back into the recreation vehicle To avoid breathing exhaust gases, follow these precautions:...

  • Page 96: Propane Gas Container

    Section 7: Fuel & Propane System Continued periodic checks of the propane system at 5,000 miles of travel (or at least once a year), by a qualified propane service representative as part of your normal maintenance is recommended. Hand tighten the LP gas system valves only, do not use a wrench or pliers as over tightening may damage the valve seals and cause them to leak.

  • Page 97: Shut Off For Re-Fueling" Label

    Section 7: Fuel & Propane System not for use on gas grills and other low pressure devices. DOT cylinders equipped with an OPD and ACME type 1 service valve are identified by the triangular service valve knob. DOT cylinders are typically marked with “top” or an arrow to indicate the correct orientation of the cylinder(s).

  • Page 98: Hoses, Pipes, Tubes & Fittings

    Section 7: Fuel & Propane System When you have a new cylinder filled for the first time, make sure your propane supplier purges your new cylinder of trapped air. Otherwise, an improper mixture of gas and air will make it impossible to light your propane appliances. No one should be inside and only the qualified propane service technician should be near the RV while the propane tank is being filled.

  • Page 99: Propane Regulator

    Section 7: Fuel & Propane System pressures exceeding those of the propane system. However, because environment and time can both contribute to the deterioration of these components, they must be inspected for wear at regular intervals. Be sure to inspect the hose before each season and when having the tank refilled. Look for signs of deterioration such as cracks or loss of flexibility.

  • Page 100: Propane Use And Safety

    Section 7: Fuel & Propane System Propane Use and Safety Propane is a colorless and odorless gas that, in the liquefied state, resembles water. An odorant (usually a sulfur compound) is added as a warning agent. If you smell propane within the vehicle, quickly and carefully perform the procedure listed on the propane system label.

  • Page 101: Cooking With Propane Gas

    Section 7: Fuel & Propane System If you have double cylinders on your recreation vehicle, use only one at a time. Otherwise, the propane supply will be drawn equally from both cylinders until the supply has been totally exhausted. Using one cylinder until it is empty, then using the second cylinder will allow you to fill the empty cylinder at your convenience without running totally out of propane.

  • Page 102: Traveling With Propane

    Section 7: Fuel & Propane System Traveling With Propane NOTE:Some states prohibit propane appliances to be operated during travel, especially in underground tunnels. Make sure you know the laws for the areas where you travel. Use care when fueling your motor fuel tanks and/ or propane containers.

  • Page 103: Double Cylinder Two Propane Cylinders

    Section 7: Fuel & Propane System Attach the 1/4” inverted flare x 24” Type 1 pigtail hose to the regulator inlet and the right hand swivel nut to the cylinder valve. Secure the cylinder to the A-frame bracket using the bolts, nuts and washers provided. Double Cylinder Mounted On A-Frame (if so equipped) When a second cylinder is installed, a tee check valve is used to replace the 90°...
  • Page 104 Section 7: Fuel & Propane System Replace all protective covers and caps on the propane system after filling. Make sure the valve is closed and the compartment door is securely latched. Maintenance Record Table of Contents...

  • Page 105: Plumbing System

    Section 8: Plumbing System Plumbing System There are two different water systems in your recreation vehicle: The fresh water system consists of the fresh water holding tank, faucets and connections, water pump, outside shower assembly (if so equipped), water heater, tub/shower, and water purification system (if so equipped).

  • Page 106: Operation

    Section 8: Plumbing System Operation Press only one tact switch at a time. As you push either the FRESH, BLK GREY1 or GREY2 switch, one or more LED lights will illuminate (from left to right) indicating the content level for that tank. When pushing the “BATT”...

  • Page 107: Fresh Water System

    Section 8: Plumbing System Fresh Water System All water contains contaminant and mineral particles that can cause fresh water system odors. Untreated well water is a major source of water system odors. The fresh water (potable water) system needs periodic sanitization and winterization to take care of all the components in the plumbing system to discourage the growth of bacteria and other organisms that can contaminate the water supply.

  • Page 108: Fresh Water Connections

    Section 8: Plumbing System For additional information on the care and operation of the pump, read the safety and operating information in the pump manufacturer’s owner’s manual. Water Pump Switch (if so equipped): Most water pump switches illuminate when the water pump is activated. In most models, the (red) pump switch is located on the monitor panel or the utility center.

  • Page 109: Potable Water Label

    Section 8: Plumbing System NOTE: The City Water Fill inlet when connected to a pressurized fresh water source sends water through the water lines and fixtures without the use of the pump. The fresh water tank cannot be filled using the city water fill (the gravity fill is used to fill the fresh water tank).

  • Page 110: Draining The Fresh Water System

    Section 8: Plumbing System Draining The Fresh Water System Water tanks may be drained through a valve located near the tank. A recreational vehicle with a demand pressure pump system will have low-point drains attached to the water lines (normally located near the water tank). These low-point drains will release water in the supply lines by opening the valves and all faucets.
  • Page 111 Section 8: Plumbing System handles should be turned so they are pointing in line with the vertical bypass tube (connecting both valves together). NOTE: In the diagram: Valve A is the black valve, valve B is the white valve. Valve D is the suction (syphon) valve that has the clear hose attached to it for siphoning in antifreeze, sanitizer or fresh water from an external container.
  • Page 112 Section 8: Plumbing System Open all hot water faucets one by one until water begins to flow continuously and a chlorine smell is noticeable. Include outside shower faucets (if so equipped). 10. Close the hot water faucets and repeat opening all cold water faucets one by one until you smell chlorine.
  • Page 113 Section 8: Plumbing System After draining the system: Water heater power should be OFF. (both switches: electric and LP gas) Water heater bypass valves (if applicable): A&B should be closed, valve C open. Put the vinegar solution into the fresh water tank. Pour the vinegar solution into the gravity fill using a hose (or funnel).
  • Page 114 Section 8: Plumbing System NOTE: : The water heater must be drained to prevent damage from freezing. It is recommended the water heater be drained and bypassed during the winterization process particularly if introducing RV antifreeze into the plumbing system. Do not drain the water heater while it is hot or under pressure! Antifreeze should be kept out of the water heater.
  • Page 115 Section 8: Plumbing System Run the pump until it is dry (approximately 15 to 20 seconds). Operating the pump longer than that with no water can damage the pump. Open all faucets in the RV. If there is an outside shower, attach the shower hose to the shower, and open the shower faucets.
  • Page 116 Section 8: Plumbing System NOTE: Antifreeze should never enter the water heater, RV water filter, refrigerator, refrigerator water filter, or fresh water tank. Turn water heater power OFF. Turn water heater gas valve (if so equipped) OFF (outside of the RV). Water heater bypass should be set to BYPASS.

  • Page 117: Water Heater

    Section 8: Plumbing System When you are done adding RV antifreeze: 11. Turn the water pump OFF. Turn siphon valve OFF. Remove the clear hose from the container of RV antifreeze. Leave the water tank shutoff valve closed to keep antifreeze out of the fresh water tank.
  • Page 118 Section 8: Plumbing System Make sure the water heater is filled with water before use as even momentary operation of the water heater without water in it may result in damage to the tank heating element and/or controls. Double check the bypass valves, make sure they are set properly. Always open both the hot and cold water faucets when filling the fresh water tank to allow air pockets to be forced out of the water heater.

  • Page 119: High Altitude Deration

    Section 8: Plumbing System the rate of deterioration; therefore, more frequent replacements may be required. If an anode rod is mostly eaten away, replace it with a new one. The water heater manufacturer recommends replacement of the anode rod when consumption or weight loss is greater than 75 percent.

  • Page 120: Outside Shower (If So Equipped)

    Section 8: Plumbing System Release the handle on the P&T valve - it should snap closed. Close the faucet and turn on the cold water supply. As the tank fills, the air pocket will develop. Repeat this procedure as often as needed to reduce the frequency of the weeping P&T valve.

  • Page 121: Faucets

    Section 8: Plumbing System To turn off the water, always close the hot/cold control (faucet) knobs. The lever on the shower head will not completely stop the flow of water; this is intentional to allow for draining. After the water has been allowed to drain from the shower head, return it to the outside shower compartment.

  • Page 122: Black/Grey Water System And Tanks

    Section 8: Plumbing System ABS plastic. Avoid using “Citrus” or biodegradable cleaners which contain “D-Limonene.” They will damage plastic materials. Contact your dealer for repair or replacement. Black/Grey Water System and Tanks Water from the sinks and shower flows into the gray water (or waste water) holding tank. Water from the toilet will flow into the sewage (or black water) holding tank (see Black/Grey Water Holding Tanks).
  • Page 123 Section 8: Plumbing System weight. The weight of the holding tank contents is not calculated into the RV cargo carrying capacity (this extra weight would reduce your available cargo capacity). Traveling with full holding tank(s) could possibly cause you to exceed the individual tire ratings and/or the RV GAWR or RV GVWR.
  • Page 124 Section 8: Plumbing System Open the black tank dump valve (depending on your model the valve may be located under the RV, or on the utility center). Close the dump valve when the black water holding tank is empty. Open the grey tank dump valve (depending on your model the valve will be located under the RV or on the utility center).
  • Page 125 Section 8: Plumbing System Dump the black water tank (see Gray Tank Drain & Black Tank Drain) and leave the black tank drain valve open. Connect a garden hose from the water supply source to the black tank flush. With the water source turned ON, flush the black water holding tank until the water running out of the black tank drain valve is clear (not discolored or cloudy).
  • Page 126 Section 8: Plumbing System Sewage (black) tank preparation Release one to two quarts (1 or 2 liters) of water into the toilet bowl. Follow the directions on your (approved RV) toilet chemical bottle (customer supplied), by placing the recommended quantity of holding tank chemical into the toilet bowl. Flush the toilet and allow at least two gallons (8 liters) of water to flow into the holding tank.

  • Page 127: Air Conditioner

    Section 9: Heating & Cooling Air Conditioner The air conditioning system is controlled by a thermostat. Cooled air enters the RV through the grill. Make sure you have sufficient power available before operating the air conditioner. Do not operate the air conditioner without the return air filter. Operating the system without the filter allows the lint and dirt that is normally stopped by the filter to accumulate on the cooling coil of the air conditioner.

  • Page 128: Furnace

    Section 9: Heating & Cooling Furnace The furnace installed in your recreation vehicle is controlled by a 12-volt DC thermostat. Depending on your model, there may be up to two thermostats enabling you to control the temperature to your comfort level. The furnace requires both 12-volt power and propane gas for full operation.

  • Page 129: Cooking Safety

    Section 10: Appliances General Cleaning Microwave and Convection Microwave IMPORTANT: Before cleaning, make sure all controls are off and the microwave oven is cool. Always follow label instructions on cleaning products. To avoid damage to the microwave oven caused by arcing due to soil buildup keep cavity, microwave inlet cover, cooking rack supports, and area where the door touches the frame clean.

  • Page 130: Cooktops; Range & Oven (If So Equipped)

    Section 10: Appliances Cooktops; Range & Oven (if so equipped) For detailed operating and safety information, refer to the manufacturer’s user guide.  During and after use, do not touch or let clothing or other flammable material come in contact with the top burners (or heating elements), burner grates or other areas near the top burners or oven until they have had sufficient time to cool.

  • Page 131: Gas Drop-In Cooktops (If So Equipped)

    Section 10: Appliances  Do not use aluminum foil on the electric range cooktop, as this material will damage the cooktop surface if it melts. Do not use aluminum foil under any circumstances on the electric range cooktop. Gas Drop-In Cooktops (if so equipped) Depending on your model, it may be equipped with either a 2 burner or 3 burner cooktop.
  • Page 132 Section 10: Appliances Gas BBQ Grill (if so equipped)  Be sure to read, understand and follow all information supplied with your recreation vehicle concerning the use of propane before operating the BBQ grill. The propane hose must be correctly connected before lighting the grill.

  • Page 133: Attaching The "Quick Coupler" Connection

    Section 10: Appliances Slide the grill onto the (2) arms against the stops. Make sure the grill is fully on the arms. Insert the retaining pins into the arms. To remove the grill, remove the retaining pins and simply slide it off of the bracket arms. Wait until grill has cooled down before removing it.

  • Page 134: Refrigerator

    Section 10: Appliances Refrigerator The refrigerator is not intended for quick freezing or cooling. We recommend stocking it with pre-frozen or pre-cooled food when possible. The shelves should not be covered with paper or plastic and the food items should be arranged so air can circulate freely. Keep the area at the back of the refrigerator clean and free of debris.

  • Page 135: Cleaning The Interior

    Section 10: Appliances Cleaning Your Refrigerator The following are general cleaning guidelines. For detailed information on cleaning your specific refrigerator, refer to the manufacturer’s user’s guide. Cleaning The Interior Unplug refrigerator or disconnect power. Hand wash, rinse, and dry removable parts and interior surfaces thoroughly. Use a clean sponge or soft cloth and a mild detergent in warm water.
  • Page 136 Section 10: Appliances Notes: Maintenance Record Table of Contents...

  • Page 137: Hdtv Antenna/Satellite System(S)

    Section 11: Electronics HDTV Antenna/Satellite System(s) HDTV Antenna (if so equipped) Your recreation vehicle is equipped with an exterior fixed height high definition TV antenna. This antenna rotates 360° and is capable of receiving any over-the-air (OTA) high definition television signals being broadcast in your receiving area.
  • Page 138 Section 11: Electronics Notes: Maintenance Record Table of Contents...

  • Page 139: Cleaning The Interior

    Section 12: Interior Cleaning The Interior To keep the value of your recreation vehicle, perform regular maintenance using the proper materials and procedures. Using the wrong cleaner may result in damage to the surfaces in your vehicle. Check with the manufacturer’s information for the recommended cleaning agent.

  • Page 140: Cabinetry & Tables

    Section 12: Interior Day/Night Shades: Clean with a mild cleaning solution using a sponge or paper towel. Wipe down with water after cleaning and dry thoroughly before raising the shade. Do not use spot remover, household cleaners or detergents to remove soiled spots, as these may cause damage to fabric or loss of color from fading.

  • Page 141: Abs Plastics

    Section 12: Interior ABS Plastics Dust and wipe clean with soft, damp cloth or chamois, wiping gently. Do not use gritty or abrasive particle soaps or scouring compound to clean ABS plastic. Avoid using “citrus” or biodegradable cleaners that contain “D-Limonene” as they may damage plastic materials. Sofa &...

  • Page 142: Pantry Or Hutch (If So Equipped)

    Section 12: Interior Booth Dinette (if so equipped) The dinette is designed to seat up to four adults. Depending on your model, there may be a storage area in the dinette bench. To access this storage, remove all the cushions and lift up on the bottom seat support.

  • Page 143: Laminate Countertops (If So Equipped)

    Section 12: Interior Do not let cleaners with bleach set on the top. Wipe them off promptly. For additional information on the removal of difficult stains or surface damage repair, refer to the countertop manufacturer’s user guide. Your recreation vehicle may be equipped with one or both of the following countertops. Laminate Countertops (if so equipped) Glass rings, food spills, water spots and smudges usually wipe off with a damp sponge.

  • Page 144: Bed Storage

    Section 12: Interior To care for the vinyl floor covering, use a damp mop with water and a mild cleaner on the entire floor. DO NOT SOAK THE FLOORING. Use care to avoid wetting the carpet edges. To avoid problems of “yellowing” linoleum, the flooring manufacturer recommends avoiding cleaners that contain oil based solvents (i.e.

  • Page 145: Cleaning The Exterior

    Section 13: Exterior Cleaning The Exterior To protect your recreation vehicle’s exterior finish, wash it often and thoroughly. For recreation vehicles with painted exterior graphics: If desired you may wash and wax your vehicle 60 days after purchase. The exterior paint does need time to cure before any wax is applied to the exterior surface.
  • Page 146 Section 13: Exterior a little “elbow grease”. Once again, after removing stubborn stains immediately rinse with clean water. Drying the recreation vehicle is just as important as washing your vehicle. Tap and well water contain many chemicals that could water stain your vehicle’s finish. We suggest using a damp natural or synthetic chamois.

  • Page 147: Frame

    Section 13: Exterior Polishing your recreation vehicle If painted surfaces have been severely damaged and have lost their original luster and color tone, polish the surface lightly with a fine polishing compound. Avoid limiting your polishing to the damaged surface only; polish a somewhat wider area, moving the polishing cloth in one direction.

  • Page 148: Exterior Roof & Sidewall Vents

    Section 13: Exterior Exterior Roof & Sidewall Vents Inspect the roof vents (including sealants) for cracks and keep them clean. Inspect the refrigerator and holding tank vents for blockages from bird nests, spider webs, leaves, etc. All exterior access doors and vents need to be kept clean and free of obstructions (i.e., insect nests, mud daubers, etc.) while the appliances are in use.
  • Page 149 Section 13: Exterior Travel Trailers - Sealant Diagram Maintenance Record Table of Contents...
  • Page 150 Section 13: Exterior Notes: Maintenance Record Table of Contents...

  • Page 151: Travel Checklist

    Section 14: Travel/Camping/Storage Checklists Travel Checklist Following is a preliminary list of items that need to be checked before leaving your home or campsite. This is a general list, which you may want to customize as you determine your own needs. Safety Make sure you follow all safety precautions noted in this owner’s manual and in any manufacturer’s operators manual when preparing to travel.
  • Page 152 Section 14: Travel/Camping/Storage Checklists Before leaving the campsite Check the area under the RV after overnight parking and look for water or other fluid leaks. If leaks are detected, find the cause and correct it immediately. Turn off propane tanks. Empty black and gray holding tanks, rinse as needed (if so equipped).
  • Page 153 Section 14: Travel/Camping/Storage Checklists Drain and flush all holding tanks (fresh water, gray water, black water and/or hot water tanks). Adding fuel stabilizer to the generator (if so equipped) will aid in preventing condensation and fuel varnishing. Disconnect 120-volt AC power to the RV. Remove all batteries from the RV and store in a place where they will not freeze.
  • Page 154 Section 14: Travel/Camping/Storage Checklists Notes: Maintenance Record Table of Contents...

  • Page 155: Featured Components Quick Reference Chart

    Your recreation vehicle may be equipped with some of the items listed below. This is a partial listing and it is not intended to cover all components. All information is the latest available at the time of publication. Jayco reserves the right to change any of the following information without notice.
  • Page 156 Section 15: Additional Information Toilet Thetford Corp. www.thetford.com See manufacturers’ user guide Winegard Company www.winegard.com TV Antenna King Jack www.kingconnect.com Water Heater, Tank DSI Atwood Greenbrier www.atwoodmobile.com Girard Systems www.greenrvproducts.com Water Heater, Tankless Truma AquaGo www.truma.com Shurflo East www.shurflo.com Water Pump, 12V Maintenance Record Table of Contents...

  • Page 157: Vehicle Maintenance Record

    Section 15: Additional Information Vehicle Maintenance Record Make: Model: Model Year: Vehicle Serial#: Service Performed Mileage Work Performed Notes Date Maintenance Record Table of Contents...
  • Page 158 Section 15: Additional Information Jayco Ownership Notification Fax Form To: (800) 825-7876 ATTENTION! Federal record keeping laws require that we maintain a file of owners of our product. Your cooperation in filling out this from will be appreciated. □ □...
  • Page 159 Section 15: Additional Information Notes: Maintenance Record Table of Contents...

Table of Contents