Danfoss FCM305 56 Instruction Manual page 51

DC link voltage [V] (DC LINK VOLTAGE [V])
Thermal load, FC [%] (FC THERMAL [%])
Hours run [Hours] (RUNNING HOURS)
Digital input [Binary code] (DIGITAL INPUT [BIN])
External reference [%] (EXTERNAL REF [%])
Status word [Hex] (STATUS WORD [HEX])
Heat sink temp. [°C] (HEATSINK TEMP [°C])
Alarm word [Hex] (ALARM WORD [HEX])
Control word [Hex] (CONTROL WORD [HEX])
Warning word 1 [Hex]
(WARNING WORD 1 [HEX])
Warning word 2 [Hex]
(WARNING WORD 2 [HEX])
Analog input 1 [mA] (ANALOG INPUT 1 [mA])
Analog input 2 [V] (ANALOG INPUT 2 [V])
Function:
This parameter allows a choice of the data value to
be displayed in line 2 of the display.
Parameters 010-012 enable the use of three
additional data values to be displayed in line 1.
NOTE!
In parameter 009, "none" [0] cannot be selected.
Description of choice:
Reference Reference [%] [%]
Reference Reference [%] Reference [%] corresponds to the total reference [%]
(sum of digital/analog/preset/bus/freeze ref./catch-
up and slow-down).
Reference Reference [unit] [unit]
Reference Reference [unit] Reference [unit] [unit] gives the sum of the references
using the unit stated on the basis of configuration in
parameter 100 (Hz, Hz and rpm).
Feedback Feedback Feedback Feedback Feedback [unit] [unit] gives the status value of terminal 1 [unit] [unit] [unit]
and 2 using the unit/scale selected in parameter
414, 415 and 416.
Frequency Frequency [Hz] Frequency [Hz] [Hz] [Hz] gives the motor frequency, i.e. the
Frequency Frequency [Hz]
output frequency to the motor.
Frequency x Scaling Frequency x Scaling [-] [-] [-] [-] [-] corresponds to the present Frequency x Scaling
Frequency x Scaling Frequency x Scaling
motor frequency f multiplied by a factor (scaling) set
M
in parameter 008.
Motor current Motor current [A] [A] [A] [A] states the phase current of the
Motor current Motor current [A] Motor current
motor measured as effective value.
T T T T T orque orque orque orque [%] orque [%] [%] [%] gives the current motor load in relation [%]
to the rated motor torque.
Power Power Power [kW] Power Power [kW] states the actual power consumed by [kW] [kW] [kW]
the motor in kW.
Power Power [HP] Power [HP] [HP] states the actual power consumed by [HP]
Power Power [HP]
the motor in HP.
= General factory setting - also applying to spare part unit, H H H H H = HVAC setting, I I I I I = Industrial setting,
( ) = display text [ ] = value for use in communication via serial communication port
MG.03.B6.2G - VLT is a registered Danfoss trademark
FCM 300 Series
[12] Motor voltage Motor voltage Motor voltage [V]
Motor voltage Motor voltage
[14] motor.
[15]
DC link voltage DC link voltage DC link voltage [V] DC link voltage DC link voltage
[16]
voltage in the FCM 300.
[21] Thermal load, FC Thermal load, FC
Thermal load, FC Thermal load, FC [%] Thermal load, FC
[22] estimated thermal load on the FCM 300. 100% is
[25]
the cut-out limit.
[26]
Hours run Hours run Hours run [Hours] Hours run Hours run [Hours] [Hours] states the number of hours that [Hours] [Hours]
[27]
the motor has run since the latest reset in
parameter 619.
[28]
Digital input Digital input Digital input Digital input Digital input [Binary code] [Binary code] states the signal states [Binary code] [Binary code] [Binary code]
from the 4 digital terminals (2, 3, 4 and 5). Input 5
[29]
corresponds to the bit at the far left. '0' = no signal,
[30] '1' = connected signal.
[31] External reference External reference [%] External reference
External reference External reference
reference as a percentage (the sum of analog/pulse/
bus).
Status word Status word [Hex] [Hex]
Status word Status word Status word [Hex] [Hex] [Hex] gives the status word sent via
the serial communication port in Hex code from the
FCM 300.
Heat sink Heat sink Heat sink temp. Heat sink Heat sink temp. temp. [°C] temp. temp.
temperature of the FCM 300. The cut-out limit is 90 ±
5°C; cutting back in occurs at 60 ± 5°C.
Alarm word Alarm word Alarm word Alarm word [Hex] Alarm word [Hex] [Hex] [Hex] [Hex] indicates one or several alarms in
a Hex code.
Control word. Control word. Control word. Control word. [Hex] Control word.
the FC motor. See Serial communication.
Warning word 1. Warning word 1. Warning word 1. [Hex]
Warning word 1. Warning word 1.
warnings in a Hex code.
Warning word 2. Warning word 2. Warning word 2. Warning word 2. Warning word 2. [Hex]
status states in a Hex code.
Analog input 1 [mA] Analog input 1 [mA], states the signal value on Analog input 1 [mA]
Analog input 1 [mA] Analog input 1 [mA]
terminal 1.
Analog input 2 [V] Analog input 2 [V] Analog input 2 [V], states the signal value on Analog input 2 [V] Analog input 2 [V]
terminal 2.
010 Display line 1.1 (DISPLAY LINE 1.1)
Value:
Reference [%]
See parameter 009.
Function:
This parameter enables a choice of the first of three
data values to be shown on the display, line 1,
position 1.
For display read-outs, press the [DISPLAY/STATUS]
button.
[V] [V] states the voltage supplied to the [V] [V]
[V] [V] [V] states the intermediate circuit [V]
[%] [%]
[%] [%] states the calculated/
[%] [%] gives the sum of the external [%]
[%]
[°C] [°C] [°C] [°C] states the present heat sink
[Hex] indicates the control word for [Hex] [Hex] [Hex]
[Hex] [Hex] indicates one or more [Hex]
[Hex]
[Hex] [Hex] [Hex] indicates one or more [Hex]
[1]
8-5