Built-In Program Mode; Sound Active Mode; Dmx Mode - ADJ UB 12H User Instructions

UB 12H

Built-In Program Mode:

1. Plug the fixture in and press the MODE button until "Pr.XX" is dis-
played. "XX" represents a number from 1-22. Use the UP or DOWN
buttons to scroll through the 22 programs. Programs 21 and 22
have adjustable base and scrolling colors. Once you have found your
desired program press the SET UP button.
2. Pressing the SET UP button will display "SP.XX". When this is dis-
played you can adjust the running speed of your desired program.
Use the UP or DOWN button to adjust the speed between "SP.01"
(slowest) and "SP.99" (fastest). Once you have set your desired run-
ning speed, you can press the SET UP button to to enter the Fade
adjustment mode.
3. Pressing the SET UP button will display "Fd.XX". When this is dis-
played you can adjust the fade speed of your desired program.
Use the UP or DOWN button to adjust the speed between "Fd.01"
(fastest) and "Fd.99" (slowest) or "Fd.00" (Off). Once you have set
your desired fade speed, you can press the SET UP button to to
enter the Flash (Strobe) mode.
4. After pressing SET UP, "FS.XX" will be displayed, this is Flash mode.
The Flash can be adjusted between "FS.00" (flash off) to "FS.15"
(fastest flash).
• PROGRAMS 21 & 22 - If you have chosen programs 21 or 22, after
the Flash mode, press the SET UP button. "C1.XX" will be displayed.
This is the base color, use the UP and DOWN buttons to scroll
through the 7 colors. Once you have chosen your base color, press
the SET UP button again so that "C2.XX" is displayed. This is the
moving color, use the UP and DOWN buttons to scroll through the 7
colors.

Sound Active Mode:

1. Plug the fixture in and press the MODE button until "SU.XX" is
displayed. "XX" represents the sound sensitivity level.
2. Use the UP or DOWN buttons to adjust the sound sensitivity.
"SU.00" is off, "SU.01 is the lowest sensitivity, and "SU.31" is the
highest. After adjusting the sound sensitivity, press SET UP if you
wish to activate the Flash mode.
3. "FS.XX" will now be displayed, this is Flash mode. The Flash can
be adjusted between "FS.00" (flash off) to "FS.15" (fastest flash).
ADJ Products, LLC - www.adj.com - UB 12H User Manual Page 10
Operating Instructions UB 12H

DMX Mode:

Operating through a DMX controller gives the user the freedom to
create their own programs tailored to their own individual needs.
This function also allows you to use your fixtures as spot lights. The
UB 12H has 4 DMX modes: 6 Channel mode, 10 Channel mode, 12
Channel mode, and 36 Channel mode. See pages 15-21 for each
mode's DMX traits.
1. This function will allow you to control each individual fixture's
traits with a standard DMX 512 controller.
2. To run your fixture in DMX mode press the MODE button until
"d.XXX" is displayed. "XXX" represents the current displayed ad-
dress. Use the UP or DOWN buttons to select your desired DMX
address, then press the SETUP button so that "Ch.XX" is displayed.
3. Use the UP or DOWN buttons to scroll through the DMX Channel
modes. The Channel modes are listed below:
• To run the 6 Channel Mode, press the MODE button until "Ch06"
is displayed. This is the 6 Channel DMX Mode.
• To run the 10 Channel Mode, press the MODE button until "Ch10"
is displayed. This is the 10 Channel DMX Mode.
• To run the 12 Channel Mode, press the MODE button until "Ch12"
is displayed. This is the 12 Channel DMX Mode.
• To run the 36 Channel Mode, press the MODE button until
"Ch36" is displayed. This is the 36 Channel DMX Mode.
4. Please see pages 15-21 for DMX values and traits.
5. After you have chosen your desired DMX Channel mode plug in
the fixture via the XLR connections to any standard DMX control-
ler.
ADJ Remote Activation:
This function is used to activate and deactivate the IR sensor. When
this function is activated you can control the fixture using either the
ADJ UC IR or Airstream App. Please see page 14 for the controls and
functions.
1. Plug the fixture in and press the MODE button until "dXX" is dis-
played. "XX" represents either "on" or "oFF".
2. Press the SET UP button until "IrXX" is displayed. "XX" represents
either "on" or "oF".
3. Press the UP or DOWN buttons to either activate the remote func-
tion (On) or deactivate it (Off).
ADJ Products, LLC - www.adj.com - UB 12H User Manual Page 11
Operating Instructions