Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Factor O2
Summary of Contents for Factor O2
- Page 1 FACTORBIKES.COM Assembly Manual...
- Page 2 Factor bicycle or frameset, and shall remain in force only as long as the original owner retains the lifetime of the original owner of each new Factor bicycle or frameset that the bicycle frame or ownership of the Factor bicycle. This lifetime limited warranty is not transferable.
- Page 3 In the event that Factor prevails in any court action, you agree to reimburse Factor for the expenses, the bicycle in, severe conditions or climates.
-
Page 4: Necessary Tools
Isopropyl alcohol Similar to a Formula 1 car, your Factor O2 requires a bit of patience and mechanical skill to achieve a truly impressive result. We recommend that you have your bicycle assembled and maintained by an authorized Factor dealer. Make sure to let your mechanic know how much you appreciate their help building the bike of your dreams! Check which rails standard are on your saddle. - Page 5 Note: Your Factor frame set requires a minimum of 90 mm of seat post insertion. The minimum insertion is clearly marked Slide 4 mm hex wrench through the hole under the top tube on the seat post.
-
Page 6: Di2 Cable Routing
Route the rear derailleur Di2 cable through the chain Note: Park Tool offers an excellent internal cable routing kit (Park Tool IR-1) to help you easily route your cables. If you do not have access to this stay. Install Di2 cable grommet. Connect to the Di2 Di2 cable routing overall view kit you can use a derailleur inner wire and a 5mm metal cable ferrule to Junction B. - Page 7 Route the Di2 cable from the Junction A to the Junction B through the down tube (as pictured) to the bottom bracket shell exit window. Route the front derailleur Di2 cable through the seat tube hole to the bottom bracket exit window. Connect to the Di2 Junction B. Carefully insert Junction B and all cables through the bottom bracket shell window.
- Page 8 Lightly grease the upper headset Lightly grease and install Lightly grease lower headset bearing and then install in upper compression ring. bearing and slide onto the headset cup. fork steerer tube. Install fork Install headset cone spacer Select the desired amount of headset spacers.
- Page 9 Install barstem Carefully remove any bulges or rough edges from the top of Note: Carefully consider all possibilities before cutting your Cut fork steerer tube (there are many blades specifically for the steerer tube with a flat file fork. Do not cut if you can foresee any reason to raise your cutting carbon tubes.
- Page 10 With the Black Inc barstem, during reassembly, Tighten the headset top cap bolt until there is no check that the top of the headset compression plug is bearing play but the headset still spins freely. no more than 3mm below the top of the stem. (If using an aftermarket stem we recommend using a 5mm spacer above the stem) Install top cap using M5 bolt and align the barstem with the...
-
Page 11: Barstem Di2 Routing
Route the rear shifter cable. Route the JC-130 through the handlebar. Note that the cables to both the front shifter and the JC-200 need to be pulled through at the same time. Connect the JC-130 and rear shifter cable to the Shimano RS910. -
Page 12: Rear Brake Cable Routing
Cut the cable housing to the correct length Route rear brake inner wire through top tube as pictured Install the cups into the frame with BRT-002 bearing press from Enduro Bearings. Clean the inside of the frame bottom bracket & the bottom Apply Loctite 641 on the grooves of the both bottom bracket bracket cups with an isopropyl alcohol. -
Page 13: Computer Mount
For 24 or 22 mm cranks install the included Wheels MFG BBright reducers/adapters. Release the bolt and remove the cover. Install the computer mount and tighten the 2 bolts to 2 Nm. Assembly Manual Computer mount... -
Page 14: Bottle Cage
Install cages and tighten M5 bolts with T20 Torx to 2 Nm. In case of dropout replacement, apply Loctite 243 on bolts threads and tighten to 1 Nm. Assembly Manual Bottle cage 10-1 Rear dropout... - Page 15 FACTORBIKES.COM...