Advertisement
Quick Links
Advertisement
Related Manuals for Factor Monza
Summary of Contents for Factor Monza
- Page 2 2025 Monza MANUAL...
- Page 3 Since specific tools and bicycle service experience is required for proper assembly installation, it is recommended that the product be assembled by a qualified bicycle mechanic. FACTOR BIKES assumes no responsibility for damages or injury due to improper assembly and installation of the product(s).
-
Page 4: Hose Routing
2025 Monza Hose routing Di2 routing Install rear brake and fish hose through the frame and out the head tube ● Install the Front and rear derailleur Di2 wires as needed, out the respective ● ● install the anti rattle rear brake hose foam sleeve ports in the frame, and out the top of the seat tube opening. - Page 5 2025 Monza Di2 Battery Installation Place the battery between the rubber clamshell battery sleeve ● ● Firmly install the battery and sleeve into the seatpost...
-
Page 6: Seatpost Installation
2025 Monza Seatpost installation Grease the area between the Apply a thick coat dielectric Install the clamp and firmly push it back into the two plates to prevent corrosion grease, or frame prep compound recess in the rear of the SP pocket. The grease... - Page 7 2025 Monza SP installation Install the SP gasket around the Install the SP into the frame. Tighten the grub screws Install the grub screw plugs post. Once the gasket is on (not using a high quality allen key to 4Nm, alternating...
- Page 8 Determine the type of SP rails on your saddle and choose the appropriate ● clamp setup from the Pizza Box of parts Factor frame sets are shipped with 7X9 mm outer rail clamps for carbon rail saddles. 7x7 mm outer rail clamps for traditional saddle rails are available through your Factor dealer.
- Page 9 2025 Monza Steerer Working with your mechanic determine the correct number of spacers, and cut the fork ● Pre-cut fork steerer making sure that it is cut 3mm below steerer tube as shown below the top of the stem. WARNING! Only use a maximum of 40mm of spacers (including tall headset cover) supplied with the frameset.
-
Page 10: Fork Mounting
2025 Monza Fork mounting Pull brake hose through the fork Grease and install the upper bearing, Split ring, Pull the hose through the lower bearing, and leave full length and dust cap. Make sure the hoses go through grease the lower bearing seat, and install... - Page 11 2025 Monza Fork mounting Apply carbon assembly paste to Install the relevant number of spacers. the compression plug, install in Note max spacer stack not to exceed 4cm steerer, and tighten to 8Nm...
- Page 12 2025 Monza Fork mounting Snake hoses through the bar, respecting Pull excess hose through barstem, which is left and which is right and exiting on your desired side corresponding front/rear brakes...
- Page 13 2025 Monza Fork mounting Alternating hoses and being sure to avoid Gently pull the hoses through the bar while starting to locate it kinking any lower it on the steerer tube until over the steerer tube. the bar sits atop the spacer stack...
- Page 14 2025 Monza Bar mounting Center the bar on the bike’s centerline prior to tightening. Ensure the spacer locating holes and mating features are aligned with the dust cap and the handlebar. Tighten the compression top cap until sufficient preload is on the bearings.
- Page 15 2025 Monza ● The 2025 Monza is configured for the use of a front derailleur, as well as supporting 1x only function. If using 1x, remove the FDM and install the supplied blanking plate. Be sure to follow all manufacturer recommendations for supporting plates, wedges, and screws when using the Monza, and tighten the FDM to no more ●...
- Page 16 2025 Monza Grommets Install the front and rear grommets, using either the Di2 passthrough style, or the E-Tap blanking style ●...
- Page 17 2025 Monza Apply a layer of good quality assembly paste Thread the cups into the frame and torque the cups Clean the inside of the frame bottom bracket to the threads of both bottom bracket cups. down to 30nm for the drive side and 40nm for the &...
- Page 18 2025 Monza The Frame is fitted with a Mini-UDH interface. If you use the UDH hanger, or a Sram Full mount derailleur you must insure the 4.5mm spacer is in place.
- Page 19 2025 Monza Install a front hub in the dropout with the free hub on non-drive side. This will allow better access for the After ensuring the dropout insert is correctly next step. Install the thru-axle with the nylon washer aligned, tighten the dropout bolt to 1 Nm.
- Page 20 2025 Monza Insure that the factory installed bezel bolts are tightened (2Nm). Install cover and tighten M5 WB bolts with a high quality 3mm Hex head to 2 Nm.
- Page 21 2025 Monza Install cages of your choice and tighten M5 bolts with a high quality 3mm Hex head to 2 Nm.
Need help?
Do you have a question about the Monza and is the answer not in the manual?
Questions and answers