Piper ARROW III Service Manual page 9

Table of Contents

Advertisement

Figure
11-13.
Installing End Bearing.......................................................................................................
11-14.
Removing Drive Pulley.....................................................................................................
11-15.
Removing Drive End Bealing ...........................................................................................
11-16.
Removing Slip Ring. .........................................................................................................
11-17.
Installing Slip Ring............................................................................................................
11-18.
Solder Points......................................................................................................................
11-19.
Installing Retainer .............................................................................................................
11-20.
Installing Drive End Shield and Bearing (Typical)...........................................................
11-21.
Installing Pulley.................................................................................................................
11-22.
Meter Connections for Alternator Performance Test ........................................................
11-23.
Exploded View of Prestolite Alternator.............................................................................
11-24.
Removal of Slip Ring End Bearing...................................................................................
11-25.
Removal of Rectifier .........................................................................................................
11-26.
Removal of Drive End Head (PA-28R-201 only)..............................................................
11-27.
Removal of End Head Bearing (Typical)..........................................................................
11-28.
Testing Rotor for Ground ..................................................................................................
11-29.
Testing Rotor for Shorts ....................................................................................................
11-30.
Installation of Drive End Head..........................................................................................
11-31.
Installation of Rectifier......................................................................................................
11-32.
Temminal Assembly..........................................................................................................
11-33.
Slip Ring End Bearing Assembly......................................................................................
11-34.
Testing Alternator..............................................................................................................
11-35.
Brush Installation...............................................................................................................
11-36.
Internal Wiring Diagram....................................................................................................
11-37.
Exploded View of Gear Reduction Starting Motor (PA-28R-201) ...................................
11-38.
Exploded View of Starting Motor (PA-28R-201T)...........................................................
11-39.
Tuming Starting Motor Commutator.................................................................................
11-40.
Testing Motor Armature for Shorts...................................................................................
11-41.
Testing Motor Fields for Grounds.....................................................................................
11-42.
No-Load Test Hook-Up.....................................................................................................
11-43.
Stall-Torque Hook-Up.......................................................................................................
11-44.
Strobe Light Connections (Earlier Models) ......................................................................
11-44a.
Strobe Light Connections (Later Models).........................................................................
11-44b.
Ignition Switch ..................................................................................................................
11-45.
Temminal Block ................................................................................................................
NOTE: (Electrical Schematics Figures 11-46 thru 11-67, see Table XI-VIII.)
12-1.
ELT Schematic Typical......................................................................................................
12-2.
ELT Portable Folding Antenna (Narco) ............................................................................
12-3.
ELT Using Fixed Aircraft Antenna (Narco)......................................................................
13-1.
Cabin Heater and Defroster (PA-28R-201) .......................................................................
13-2.
Cabin Heater and Defroster (PA-28R-201T).....................................................................
13-3.
Ovemead Vent System and Fresh Air System...................................................................
Revised: 2/13/89
LIST OF ILLUSTRATIONS (CONT)
1A9
Aerofiche
Grid No.
2H4
2H5
2H5
2H6
2H6
2H7
2H7
2H8
2H8
2H10
2H12
2H13
2H13
2H14
2H14
2H15
2H15
2H16
2H16
2H17
2H18
2H18
2H19
2H19
2H21
2H22
2H23
2H23
2H24
2H24
2I1
2I7
2I8
2I12
2I13
2K3
2K4
2K4
2K7
2K8
2K9

Hide quick links:

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the ARROW III and is the answer not in the manual?

This manual is also suitable for:

Turbo arrow iii

Table of Contents

Save PDF