Piper ARROW III Service Manual page 7

Figure
7-20. Installation of Anchor Bolt................................................................................................
7-21. Brake System Installation..................................................................................................
7-22. Brake Master Cylinder (Hand/Parking Brake)..................................................................
7-23. Toe Brake Installation........................................................................................................
7-24. Brake Cylinder (1700) (Toe Brake)...................................................................................
7-25. Brake Cylinder (10-27) (Toe Brake) .................................................................................
7-26. Bleeding Brakes.................................................................................................................
7-27. Nose Gear Service Tolerances...........................................................................................
7-28. Main Gear Service Tolerances...........................................................................................
8-1. Engine Cowling Installation..............................................................................................
8-3. Propeller Installation .........................................................................................................
8-4. Propeller Blade Minor Repair ...........................................................................................
8-5. Propeller Governor............................................................................................................
8-6. Engine Installation.............................................................................................................
8-7. Schematic Diagram of Turbocharger System....................................................................
8-8. Induction System Installation............................................................................................
8-8a. Magneto Assembly............................................................................................................
8-9. Contact Spring Inspection .................................................................................................
8-10. Contact Points....................................................................................................................
8-11. Impulse Coupling ..............................................................................................................
8-12. Flyweight Clearance of Impulse Coupling........................................................................
8-13. Rotor Holding Tool Installed.............................................................................................
8-14. Timing Kit Installed...........................................................................................................
8-15. Cast-In Timing Marks........................................................................................................
8-16. Fabricated Pointer..............................................................................................................
8-17. Engine Timing Marks........................................................................................................
8-18. Removing Spring From Lead Assembly...........................................................................
8-19. Assembly Tool...................................................................................................................
8-20. Assembly Tool Application...............................................................................................
8-21. Measuring Lead Assembly Length....................................................................................
8-22. Ferrule Seating Tool ..........................................................................................................
8-23. Measuring Wire From Top of Ferrule ...............................................................................
8-24. Needle................................................................................................................................
8-25. Installing Grommet Over Lead Assemblies......................................................................
8-26. Lead Assembly Installed in Grommet...............................................................................
8-27. Wire Doubled Over For Installation of Eyelet ..................................................................
8-28. Ignition Schematic.............................................................................................................
8-29. Removing Frozen Spark Plug............................................................................................
8-30. Lubrication System Maintenance Points...........................................................................
8-31. Schematic Diagram of Fuel Injection System...................................................................
8-32. Fuel Injection Nozzle Assembly .......................................................................................
8-33. Engine Controls.................................................................................................................
8-34. Idle Speed and Mixture Adjustment Points.......................................................................
8-35. Sectional View of Altitude Compensating Fuel Pump Assembly.....................................
8-36. Exhaust Bypass Screw.......................................................................................................
8A-l. Propeller Installation (Hartzell).........................................................................................
8A-2. Propeller Blade Minor Repair ...........................................................................................
8A-3. Propeller Governor............................................................................................................
8A-3a. Engine Cowling Installation..............................................................................................
8A-4. Engine Installation (PA-28R-201).....................................................................................
8A-4a. Adjustment of Engine Controls.........................................................................................
8A-5. Fuel Injector.......................................................................................................................
8A-6. Schematic Diagram of RSA Injector System....................................................................
Interim Revision: 2/21/95
LIST OF ILLUSTRATIONS (cont)
1A7
Aerofiche
Grid No.
1K16
1K18
1K19
1K20
1K21
1K21
1L1
1L9
1L12
2A13
2A14
2A16
2A17
2A20
2A23
2B5
2B7
2B8
2B9
2B10
2B10
2B11
2B11
2B12
2B12
2B13
2B15
2B17
2B17
2B17
2B19
2B19
2B19
2B19
2B20
2B20
2B21
2B23
2B24
2C2
2C3
2C4
2C6
2C8
2C10
2C21
2C22
2C24
2D2
2D4
2D7
2D8
2D9