HP 8642A Operation And Calibration Manual page 250

Index
SET SEQ, 3-161
Shift key functions, 3-35
SINGLE (sweep mode)
Amplitude, 3-84
Frequency, 3-51
SPCL, 3-168
Special functions, 3-35, 3-167
O.SPCLS 4-9 OFF, 3-172
03.SERVICE MODE-SEE MANUAL, 3-172, 3-201
04.ALC OFF, 3-74
05.EXT LOW RATE FM ON, 3-112
06.FM PRE-EMPHASIS ON, 3·113
07.LOW DISTORTION FM/<pM ON, 3-115, 3-124
08.PREFER HETERODYNE BAND, ,3-41
09.ATTEN RANGE HOLD ON, 3-74
100.ALL SPCLS
<
200 OFF, 3-172
111.SPCL FUNC VERIFY OFF, 3-172
112.INT+EXT LOW.RATE FM ON, 3-112
113.MOD.FRQ CORRECTION OFF, 3-133
1I4.NEGATIVE <PM POLARITY, 3-124
1I5.NEGATIVE FM POLARITY, 3-115
116.DCFM CORRECTION OFF, 3-116
117.DCFM UPDATE MODE ON, 3-116
118.AC-COUPLED DCFM ON, 3-116
119.DISABLE SETTLING, 3-173
121.SWEEP UP AND DOWN ON, 3-66, 3-93
122.LINEAR AMPTD SWEEP, 3-94
123.PHASE CONTINUOUS SWEEP, 3-49
134.TURN OFF LCD LIGHTING, 3-174
135.DISABLE DISPLAY, 3-174
240.DECR FREQ 0.1 HZ, 3-42
241.lNCR FREQ 0.1 HZ, 3-42
242.PHASE DECR 1 DEGREE, 3-42
243.PHASE INCR 1 DEGREE, 3-42
244.PHASE DECR 5 DEGREES, 3-42
245.PHASE INCR 5 DEGREES, 3-42
248.CAL MOD FREQ AGAIN, 3-133
249.DISPLAY FIRMWARE INFO. 3-176
250.PHASE ADJ.=KNOBjUPjDN, 3-42
251.CLEAR RECALL REGS, 3-159
Detailed list, 3-176
Display current, 3-169
3-212
Special functions (continued)
Select, 3-168
Summary, 3-170, 3-171
Turn off, 3-169
SRQ (see also RQS), 3-200
SRQ (annunciator), 3-207
START AMPTD, 3-84
START FREQ, 3-50
Step keys, 3-149
Stereo separation, 3-38, 3-112
STOP AMPTD, 3-84
STOP FREQ, 3-50
Store (see save or recall), 3-159
SWEEP (abbreviation), 3-83
Model 864 2A/R
SWPNG (annunciator), 3-49, 3-83, 3-207
T
TIME
Amplitude, 3-85
Frequency, 3-52
TLK (annunciator), 3-207
u
Units conversion, 3-205
UR (abbreviation), 3-208
User messages, writing to the display, 3-201
UV (abbreviation), 3-208
v
VL (abbreviation), 3-208
w
Writing messages to the display, 3-201
x
X AXIS output, 3-3, 3-49, 3-65, 3-83, 3-93
z
Z AXIS out.put, 3-3, 3-39, 3-65, 3-83, 3-93