1. Manuals
  2. Brands
  3. The Handy Manuals
  4. Spreader
  5. THS80
  6. Instruction manual

The Handy THS80 Instruction Manual

Push, 80lb, 36kg
Hide thumbs Also See for THS80:
Table of Contents

Advertisement

Quick Links

Download this manual
INSTRUCTION MANUAL
80LB (36kgs)
PUSH SPREADER
Model No: THS80 -- Product No: 193897002
ASSEMBLY REQUIRED
SAVE THESE INSTRUCTIONS
SPARES & SUPPORT: 01793 333212
Please read & understand this manual, paying attention to the safety instructions, before use.
The manufacturer reserves the right to change the product specification and livery according to
continued product improvements.
Images used are for illustration purposes only
01/02/2017

Advertisement

Table of Contents
loading

Related Manuals for The Handy THS80

Summary of Contents for The Handy THS80

  • Page 1 INSTRUCTION MANUAL 80LB (36kgs) PUSH SPREADER Model No: THS80 -- Product No: 193897002 ASSEMBLY REQUIRED SAVE THESE INSTRUCTIONS SPARES & SUPPORT: 01793 333212 Please read & understand this manual, paying attention to the safety instructions, before use. The manufacturer reserves the right to change the product specification and livery according to continued product improvements.

  • Page 2: Table Of Contents

    CONTENTS SPECIFICATION IMPORTANT INFORMATION GENERAL SAFETY INSTRUCTIONS COMPONENTS ASSEMBLY ADJUSTMENTS MAINTENANCE OPERATION RATE SETTINGS PARTS DIAGRAM PARTS LIST WARRANTY NOTES ASSEMBLY IS REQUIRED This product requires assembly before use. See the “Assembly” section for instructions. Please check that all parts required for the assembly of this spreader are included. If for any reason you believe a part for the assembly is missing or damaged, please contact us.

  • Page 3: Specification

    SPECIFICATIONS The manufacturer reserves the right to change the product specification and livery according to continued product improvements. Model THS80 Product Number 193897002 Capacity (Weight) 36kg Wheel Diameter 176mm Tyre 4.10/3.50-6 Tyre Rating 2 Ply Tyre Maximum PSI 25psi (Do not exceed)
  • Page 4 DO NOT OVERREACH OPERATION SPEED Keep proper footing and balance at all times Do not exceed 10mph, to avoid personal when using the machine. Never stand on the injury and/or equipment damage. machine. Serious injury could occur if the TYRE INFLATION machine is tipped or if the moving parts are Before operating, make sure the tyres have unintentionally contacted.

  • Page 5: Components

    COMPONENTS Hex Bolt M6x40 4PCS Hex Bolt M6x35 2PCS NOTE: Parts Lists are supplied for information purposes only, not all parts are stocked individually & we recommend you contact our Spares Team on 01793 333212 for expert advice.

  • Page 6: Assembly

    ASSEMBLY STEP 1  Install the impeller onto the gearbox and axle assembly.  Align the impeller with the hole on the axle, located nearest the gearbox.  Insert M4x20 screw, through the side of the impeller and the gearbox axle. Tighten until secure.
  • Page 7 STEP 2  Attach the Wheel Assembly Frame to each side of the Gearbox Assembly and Fixing Connecting Rod, insert two bolts M6x35 into the fixing connecting rod through the Wheel Assembly Frame.  Make sure the hole in the Gearbox Axle is on the RIGHT SIDE, when assembling, as shown. ...
  • Page 8 STEP 3  Insert the Inner Axle Bushing into the Outer Axle Bushing and make sure they are tight.  Install the right Wheel Assembly onto the right Axle, using M5x45 Bolt & M5 Lock Nut and install the End Cap onto the right Axle, using a wooden or rubber mallet. ...
  • Page 9 STEP 4  Insert Upper Handle into the Support Leg and tighten using M6x40 Bolts & M6 Lock Nuts. NOTE: NOW GO BACK AND TIGHTEN ALL NUTS AND BOLTS STARTING WITH THE WITH FIRST STEP. DO NOT OVER TIGHTEN.
  • Page 10 STEP 5  Insert the steel wire head of the control cable into the small hole on the Gauge & Lever Assembly.  Release the two M5x10 Bolts & Lock Nuts on the Press Plate.  Put the Plastic Tube into the slot of the Press Plate. ...

  • Page 11: Adjustments

    ADJUSTMENTS STEP 6 When you have finished all the above steps, if the hole at the bottom of hopper cannot be closed and opened completely by using the handle you may need to the follow these additional steps.  Release the two bolts M5x10 on clamp as shown. ...

  • Page 12: Maintenance

    MAINTENANCE LUBRICATE Maintenance spray or multi-purpose grease can be applied to the wheel axle prior to long-term storage. Oiling is not necessary. GEARBOX DO NOT open the gearbox. The gears are permanently lubricated from the factory. CHECK TYRE INFLATION Prior to using the Spreader, ensure the tyres are sufficiently inflated. We recommend the use of FOOT or HAND inflation devices only.

  • Page 13: Rate Settings

    RATE SETTINGS Our spreaders are designed to spread dry, powdered or granulated materials thinly and evenly over reasonably smooth surfaces.  Ensure that the material is dry and free-running. If in doubt pass it through a sieve with 3mm mesh to remove lumps. ...
  • Page 14 NOTES _____________________________________________ _____________________________________________ _____________________________________________ _____________________________________________ _____________________________________________ _____________________________________________ _____________________________________________ _____________________________________________ _____________________________________________ _____________________________________________ _____________________________________________ _____________________________________________ _____________________________________________ _____________________________________________ _____________________________________________ _____________________________________________ _____________________________________________ _____________________________________________ _____________________________________________ _____________________________________________ _____________________________________________ _____________________________________________ _____________________________________________ _____________________________________________ _____________________________________________ _____________________________________________ _____________________________________________...

  • Page 15: Parts Diagram

    PARTS DIAGRAM NOTE: Parts Lists are supplied for information purposes only, not all parts are stocked individually & we recommend you contact our Spares Team on 01793 333212 for expert advice.

  • Page 16: Parts List

    PARTS LIST Part No. Description Part No. Description Carriage Bolt Lock Nut TH137-2 TH137-24 M6x25 Lock Washer TH137-3 TH138-26GM Support Leg Ø8 Wheel Frame TH138-3 Gauge Plate TH138-27GM (Right) Adjust Handle TH137-5 TH138-28 Thin Washer Pole TH137-6 Adjust Handle A TH137-36GM Wheel &...
  • Page 17 GJ HANDY & CO LTD USER WARRANTY POLICY Users Statement of Warranty Each new machine is warranted against defective material or assembly of material under normal usage. The warranty applies to the original purchaser and covers faulty parts and the labour involved in replacing and repairing those parts, which are of original manufacture.
  • Page 18 GJ HANDY & CO LTD USER WARRANTY POLICY Not covered by this warranty a) The warranty policy does not cover any depreciation or damages caused by ordinary wear, rusting or corrosion, lack of correct maintenance or operation, misuse, abuse, lack of transportation or accident.

  • Page 20: Tel: 01793 333212

    For spares or support of your handy product, please contact us: Tel: 01793 333212 (Mon – Fri 8.00am to 5.30pm excl. Bank Holidays) Email: customerservice@handydistribution.co.uk To see our range of garden machinery & equipment visit: www.thehandy.co.uk Making gardening easier & affordable since 1938 Distributed by Handy Distribution, Murdock Road, Dorcan, Swindon, SN3 5HY...

This manual is also suitable for:

193897002

Table of Contents