Brocade Communications Systems 5300 Hardware Installation Manual
  1. Manuals
  2. Brands
  3. Brocade Communications Systems Manuals
  4. Switch
  5. 5300
  6. Hardware installation manual
Brocade Communications Systems 5300 Hardware Installation Manual

Brocade Communications Systems 5300 Hardware Installation Manual

Hide thumbs Also See for 5300:
Table of Contents

Advertisement

Quick Links

See also: Administrator's Manual , Reference Manual
HARDWARE INSTALLATION GUIDE
Brocade 5300
Hardware Installation Guide
53-1000858-07
28 February 2017

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the 5300 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Brocade Communications Systems 5300

Summary of Contents for Brocade Communications Systems 5300

  • Page 1 HARDWARE INSTALLATION GUIDE Brocade 5300 Hardware Installation Guide 53-1000858-07 28 February 2017...
  • Page 2 United States government. The authors and Brocade Communications Systems, Inc. assume no liability or responsibility to any person or entity with respect to the accuracy of this document or any loss, cost, liability, or damages arising from the information contained herein or the computer programs that accompany it.

  • Page 3: Table Of Contents

    Supported hardware and software........................................11 What’s new in this document..........................................11 Device Overview..........................................13 Brocade 5300 overview............................................13 Port side of the Brocade 5300.........................................14 Non-port side of the Brocade 5300......................................16 Brocade 5300 Management..........................................16 Ports on Demand license............................................ 17 Brocade Inter-Switch Link (ISL) Trunking..................................... 17 Preparing for Installation.........................................19...
  • Page 4 Local time synchronization........................................61 Setting the date...............................................62 Setting time zones............................................62 Synchronizing local time using NTP......................................63 Monitoring the Device........................................65 Powering the Brocade 5300 on and off....................................... 65 LED activity interpretation........................................... 65 Brocade 5300 LEDs........................................... 65 LED locations..............................................65 LED patterns..............................................67 POST and boot specifications...........................................69...
  • Page 5 Brocade 5300 Technical Specifications..................................81 Switch components..............................................81 Weight and physical dimensions........................................81 Facility requirements..............................................82 Power supply specifications..........................................82 Environmental requirements..........................................82 General specifications............................................83 Data transmission ranges............................................ 84 Memory specifications............................................84 Fibre Channel port specifications........................................84 Serial port specifications............................................85 Regulatory certifications............................................85 Regulatory compliance (EMC) ........................................
  • Page 6 Brocade 5300 Hardware Installation Guide 53-1000858-07...

  • Page 7: Preface

    Identifies command names. Identifies keywords and operands. Identifies the names of GUI elements. Identifies text to enter in the GUI. italic text Identifies emphasis. Identifies variables. Identifies document titles. Identifies CLI output. Courier font Brocade 5300 Hardware Installation Guide 53-1000858-07...

  • Page 8: Command Syntax Conventions

    By sending your feedback to documentation@brocade.com Provide the publication title, part number, and as much detail as possible, including the topic heading and page number if applicable, as well as your suggestions for improvement. Brocade 5300 Hardware Installation Guide 53-1000858-07...

  • Page 9: Contacting Brocade Technical Support

    Brocade Supplemental Support augments your existing OEM support contract, providing direct access to Brocade expertise. For more information, contact Brocade or your OEM. • For questions regarding service levels and response times, contact your OEM/solution provider. Brocade 5300 Hardware Installation Guide 53-1000858-07...
  • Page 10 Brocade 5300 Hardware Installation Guide 53-1000858-07...

  • Page 11: About This Document

    Fabric OS v6.1.0 and later, documenting all possible configurations and scenarios is beyond the scope of this document. This document is specific to the Brocade 5300 and Fabric OS 5.3.0. To obtain information about a Fabric OS version other than v5.3.0, see the documentation specific to that OS version.
  • Page 12 Brocade 5300 Hardware Installation Guide 53-1000858-07...

  • Page 13: Device Overview

    Brocade 5300 overview The Brocade 5300 is an 80-port 1, 2, 4, or 8 Gbps Fibre Channel switch that delivers Brocade sixth generation ASIC technology and architecture for Fibre Channel Storage Area Networks (SANs). The Brocade 5300 is designed for the needs of enterprise environments that require a high-port footprint for port aggregation.

  • Page 14: Port Side Of The Brocade 5300

    The Brocade EZSwitchSetup wizard that makes SAN configuration a three-step point-and-click task. Port side of the Brocade 5300 The port side of the Brocade 5300 includes the system status LED, console port, Ethernet port and LEDs, USB port, and Fibre Channel ports and the corresponding port status LEDs.
  • Page 15 You can also use port index and PIDs to identify a port. For more information, refer to the Fabric OS Administrator's Guide FIGURE 2 Trunking port groups and port numbers of the Brocade 5300 Trunking port group 1; FC ports 00-07 Trunking port group 2;...

  • Page 16: Non-Port Side Of The Brocade 5300

    4 Fan assembly #3 Brocade 5300 Management You can use the management functions built into the Brocade 5300 to monitor the fabric topology, port status, physical status, and other information to help you analyze switch performance and to accelerate system debugging.

  • Page 17: Ports On Demand License

    Ports on Demand license The Brocade 5300 has 80 ports. By default, ports 0-47 are enabled. As your needs increase, you can activate unlicensed ports by purchasing and installing the Brocade Ports on Demand (POD) optional licensed product. After it has been installed, the license appears in the licenseShow command output as Ports on Demand license .
  • Page 18 Brocade 5300 Hardware Installation Guide 53-1000858-07...

  • Page 19: Preparing For Installation

    • Recommendations for cable management............................21 • Items included with the Brocade 5300..............................22 General precautions When using this product, observe all danger, caution, and attention notices in this manual. The notices are accompanied by symbols that represent the severity of the safety condition.

  • Page 20: Power Precautions

    Ensure that the airflow direction of the power supply unit matches that of the installed fan tray. The power supplies and fan trays are clearly labeled with either a green arrow with an "E", or an orange arrow with an "I." Brocade 5300 Hardware Installation Guide 53-1000858-07...

  • Page 21: Eia Rack Considerations

    Leave at least 1 m (3.28 ft) of slack for each port cable. This provides room to remove and replace the switch, allows for inadvertent movement of the rack, and helps prevent the cables from being bent to less than the minimum bend radius. Brocade 5300 Hardware Installation Guide 53-1000858-07...

  • Page 22: Items Included With The Brocade 5300

    Items included with the Brocade 5300 The following items are included with the standard shipment of the Brocade 5300. When you open the Brocade 5300 packaging, verify that these items are included in the package and that no damage has occurred during shipping: •...

  • Page 23: Mounting The Device

    In an EIA rack using an optional mid-mount rack kit for switches. The optional mid-mount rack kit for switches can be ordered from your switch retailer. Installing a standalone Brocade 5300 Perform this task to install the Brocade 5300 as a standalone unit. Unpack the Brocade 5300 and verify the items listed on Items included with the Brocade 5300 on page 22.

  • Page 24: Installing The 1U, 1.5U, And 2U Mid-Mount Kit For Two-Post Racks (Xbr-000165, Xbr-000175, And Xbr-R000292)

    The following parts are provided with the 1U, 1.5U, or 2U Mid-Mount Rack Kit for Two-Post Racks (XBR-000165, XBR-000175, and XBR-R000292). NOTE Depending on the device type, not all parts may be used in an installation. Brocade 5300 Hardware Installation Guide 53-1000858-07...

  • Page 25: Attaching The Front Brackets To The Device

    To install the device in a recessed position in the rack, use the bracket holes that are set back from the end of the bracket. Insert 8-32 x 5/16-in. screws through the rest of the holes in the bracket and into the corresponding holes in the device. Brocade 5300 Hardware Installation Guide 53-1000858-07...

  • Page 26: Attaching The Device To A Rack

    Attach the right front bracket to the right rack rail using three 10-32 x 5/8-in. screws and three 10-32 retainer nuts. Attach the left front bracket to the left rack rail using three 10-32 x 5/8-in. screws and three 10-32 retainer nuts. Brocade 5300 Hardware Installation Guide 53-1000858-07...

  • Page 27: Attaching The Rear Brackets To The Rack

    Position the right rear bracket in the right rear of the device as shown in the following figure. Attach the brackets using three 10-32 x 5/8-in. screws and 10-32 retainer nuts. Repeat step 1 and step 2 to attach the left rear bracket. Brocade 5300 Hardware Installation Guide 53-1000858-07...

  • Page 28: Attaching The Rear Brackets To The Device

    Align the left rear bracket to the left rear of the device and use two 8-32 x 5/16-in. screws to attach the bracket to the device as shown in the following figure. Brocade 5300 Hardware Installation Guide 53-1000858-07...

  • Page 29: Installing The 1U And 2U Fixed-Mount Rack Kit For Four-Post Racks (Xbr-R000162)

    Allow 15 to 30 minutes to complete the installation procedure. The following items are required to install a device using the 1U and 2U Fixed-Mount Rack Kit for Four-Post Racks (XBR-R000162). • #2 Phillips torque screwdriver • 1/4-inch slotted-blade torque screwdriver Brocade 5300 Hardware Installation Guide 53-1000858-07...

  • Page 30: Parts List

    CAUTION Use the screws specified in the procedure. Using longer screws can damage the device. Parts list The following parts are provided with the 1U and 2U Fixed-Mount Rack Kit for Four-Post Racks (XBR-R000162). Brocade 5300 Hardware Installation Guide 53-1000858-07...
  • Page 31 Not all parts may be used with certain installations depending on the device type. NOTE Although this document describes how to install single-height (1U) and double-height (2U) devices, the illustrations show a single-height device as a typical installation. Brocade 5300 Hardware Installation Guide 53-1000858-07...

  • Page 32: Attaching The Front Brackets

    Repeat step 1 through step 3 to attach the left front bracket to the left side of the device. Tighten all the 8-32 x 5/16-in. screws to a torque of 15 in-lbs (17 cm-kgs). FIGURE 10 Attaching the front brackets Bracket, front right Screw, 8-32 x 5/16-in., panhead Phillips Brocade 5300 Hardware Installation Guide 53-1000858-07...

  • Page 33: Installing The Device In The Rack

    Attach the right front bracket to the right front rack post using two 10-32 x 5/8-in. screws and two retainer nuts. Attach the left front bracket to the left front rack post using two 10-32 x 5/8-in. screws and two retainer nuts. Brocade 5300 Hardware Installation Guide 53-1000858-07...

  • Page 34: Attaching The Rear Brackets To The Front Brackets

    Complete the following steps to attach the rear brackets to the front brackets. Position the right rear bracket inside the right front bracket, as shown in the following figure. Attach the brackets using four 6-32 x 1/4-in. screws. Brocade 5300 Hardware Installation Guide 53-1000858-07...

  • Page 35: Attaching The Rear Brackets To The Rack Posts

    Attach the right rear bracket to the right rear rack post using two 10-32 x 5/8-in. screws and two retainer nuts, as shown in the following figure. Attach the left rear bracket to the left rear rack post using two 10-32 x 5/8-in. screws and two retainer nuts. Brocade 5300 Hardware Installation Guide 53-1000858-07...

  • Page 36: Slide Rack Mount Kit (Xbr-R000070)

    Before mounting your device, review any specific installation and facility requirements in this Hardware Installation Guide. • Hardware devices illustrated in these procedures are only for reference and may not depict the device you are installing into the rack. Brocade 5300 Hardware Installation Guide 53-1000858-07...

  • Page 37: Safety Precautions

    The following parts are provided with the 1U and 2U Slide-Mount Rack Kit for Four-Post Racks (XBR-R000070). NOTE Use the screws specified for use with the device. Longer screws can damage the device. NOTE Depending on the device type, not all parts may be used in an installation. Brocade 5300 Hardware Installation Guide 53-1000858-07...
  • Page 38 3, 4, and 5 installed on the outer slide rail (each slide assembly is bagged separately) (2) FIGURE 15 Rack kit parts(2 of 4) Phillips screw, 10-32 x 1/2 in., black (12) Alignment washer (12) Three-hole rack nut bar, 8-32 (4) Retainer nut, 10-32 (12) Brocade 5300 Hardware Installation Guide 53-1000858-07...

  • Page 39: Installing The Device

    Locate the slide assembly in the kit, as shown in the following figure. The slide assembly comes fully assembled and includes all of the parts shown in the figure. Pull the inner slide rail out until the lock engages. Refer to the following figure. Brocade 5300 Hardware Installation Guide 53-1000858-07...
  • Page 40 NOTE The hole pattern is identical for all 1U, 1.5U, and 2U devices. Attach the rail using three Phillips 8-32 x 3/16-in. screws. Tighten the screws to a torque of 15 in-lbs (17 cm-kgs). Brocade 5300 Hardware Installation Guide 53-1000858-07...
  • Page 41 For recessed mounting, you can use the back rack mount brackets on the front instead of the left and right rack mount brackets. Tighten the screws to a torque of 15 in-lbs (17 cm-kgs). Brocade 5300 Hardware Installation Guide 53-1000858-07...
  • Page 42 Perform the following steps to reposition the port side L-bracket for correct mounting. On the port side of the outer slide rail, using the 11/32-inch wrench, loosen the nuts securing the L-bracket, as shown in the following figure. Brocade 5300 Hardware Installation Guide 53-1000858-07...
  • Page 43 Leave the middle hole empty on the port side for securing the rack mount bracket later (refer to Inserting the device in the rack on page 48). Tighten the screws to 15 in-lbs (17 cm-kgs). Brocade 5300 Hardware Installation Guide 53-1000858-07...
  • Page 44 Perform the following steps to install the square-hole hardware using Method A. Position the outer slide rail inside the rack posts with the closed ends of the slide rail toward the non-port side of the rack, as shown in the following figure. Brocade 5300 Hardware Installation Guide 53-1000858-07...
  • Page 45 Phillips screw, 10-32 x 1/2 in., black (5 each side) Rack post (non-port side) Three-hole slide mount L-bracket (2 each side) Three-hole slide mount L-bracket Rack post (port side) Retainer nut, 10-32 (5 each side) Outer slide rail Brocade 5300 Hardware Installation Guide 53-1000858-07...
  • Page 46 Leave the middle hole empty on the port side for securing the rack mount bracket later (refer to Inserting the device in the rack on page 48); however, position an alignment washer between the L-bracket and the rack post. Tighten the screws to 15 in-lbs (17 cm-kgs). Brocade 5300 Hardware Installation Guide 53-1000858-07...
  • Page 47 Three-hole slide mount L-bracket Three-hole slide mount L-bracket (2 each side) Alignment washer (6 each side) Rack post (port side) Rack post (non-port side) Outer slide rail Three-hole rack nut bar, 8-32 (2 each side) Brocade 5300 Hardware Installation Guide 53-1000858-07...
  • Page 48 Ensure that the clips do not interfere with the movement of the rails. Position all the clips either with the tabs above or with the tabs below the rail. FIGURE 25 Attaching the power cord clips Three-hole slide mount L-bracket Power cord clips (3 each side) Slide assembly Brocade 5300 Hardware Installation Guide 53-1000858-07...
  • Page 49 FIGURE 26 Inserting the power cords in clips Power cord Slide assembly Position the device next to the rack; align and insert the inner rails inside the outer rails, as shown in the following figure. Brocade 5300 Hardware Installation Guide 53-1000858-07...
  • Page 50 Check the rail alignment by sliding the device out and back into the rack. FIGURE 27 Inserting the device device Slide assembly open end Slide assembly closed end Inner slide rail Outer slide rail Lock-release lever Brocade 5300 Hardware Installation Guide 53-1000858-07...
  • Page 51 FIGURE 28 Securing rack mount brackets for round-hole rack posts Right rack mount bracket Three-hole rack nut bar, 8-32 Rack post Phillips screw, 10-32 x 1/2 in., black FIGURE 29 Method A for securing rack mount brackets for square-hole rack posts Brocade 5300 Hardware Installation Guide 53-1000858-07...
  • Page 52 Slide Rack Mount Kit (XBR-R000070) Right rack mount bracket Retainer nut, 10-32 Rack post Phillips screw, 10-32 x 1/2 in., black Three-hole slide mount L-bracket FIGURE 30 Method B for securing rack mount brackets for square-hole rack post Brocade 5300 Hardware Installation Guide 53-1000858-07...

  • Page 53: Installing The 1U And 2U Non-Port Side Fixed-Mount Rack Kit (24") For Four-Post Racks (Xna-000073 And Xna-100073)

    Hardware devices illustrated in these procedures are only for reference and may not depict the device you are installing into the rack. Single height (1U) devices are shown for illustration purposes, but the double height (2U) installation is similar. Brocade 5300 Hardware Installation Guide 53-1000858-07...

  • Page 54: Time And Items Required

    Screw, 10-32 x 5/8-in., panhead Phillips (8) Short rear brackets, right and left Retainer nut, 10-32 (8) Screw, 8-32 x 5/16-in., panhead Phillips (12) Clip nuts, 10-32, for round-hole rack posts (8) Screw, 6-32 x 1/4-in., flathead Phillips (8) Brocade 5300 Hardware Installation Guide 53-1000858-07...

  • Page 55: Attaching Front Brackets

    Select the correct nuts for either square or round holes in the rack posts. A single height device is shown, but the installation for a double height device is the same. Brocade 5300 Hardware Installation Guide 53-1000858-07...

  • Page 56: Attaching The Rear Brackets To Front Brackets

    Repeat step 1 through step 3 to attach the left rear bracket to the left front bracket. FIGURE 34 Attaching the rear brackets to the front brackets Bracket, front right Bracket, rear right Screws, 6-32 x 1/4-in., flathead Phillips (4) Brocade 5300 Hardware Installation Guide 53-1000858-07...

  • Page 57: Attaching The Rear Brackets To The Rack Posts

    Tighten the 10-32 x 5/8-in. screws to a torque of 25 in-lbs. (29 cm-kgs). FIGURE 35 Attaching the rear brackets to the rack posts Bracket, front right Bracket, short rear right Retainer nuts, 10-32 (2) Screws, 10-32 x 5/8-in., panhead Phillips (2) Brocade 5300 Hardware Installation Guide 53-1000858-07...
  • Page 58 Brocade 5300 Hardware Installation Guide 53-1000858-07...

  • Page 59: Initial Setup And Verification

    Date and time settings.....................................61 Once you have set up the Brocade 5300 in a rack or as a standalone switch, it is time to give it power and a basic configuration. If you are going to use the Brocade 5300 in a single-switch setup, you can use EZSwitchSetup to complete the basic configuration.

  • Page 60: Switch Ip Address

    Switch IP address You can configure the Brocade 5300 with a static IP address, or you can use a DHCP (Dynamic Host Configuration Protocol) server to set the IP address of the switch. DHCP is enabled by default. The Brocade 5300 supports both IPv4 and IPv6.

  • Page 61: Date And Time Settings

    The Brocade 5300 maintains the current date and time inside a battery-backed real-time clock (RTC) circuit. Date and time are used for logging events. Switch operation does not depend on the date and time; a Brocade 5300 with an incorrect date and time value still functions properly.

  • Page 62: Setting The Date

    Use one of the two following procedures to set the time zone. The following procedure describes how to set the current time zone using timezone_fmt mode to Central Standard time. Log into the switch using the default password, which is password. Brocade 5300 Hardware Installation Guide 53-1000858-07...

  • Page 63: Synchronizing Local Time Using Ntp

    The following example shows how to set up more than one NTP server using a DNS name: switch:admin> tsclockserver "10.32.170.1;10.32.170.2;ntp.localdomain.net" Updating Clock Server configuration...done. Updated with the NTP servers Changes to the clock server value on the principal or primary FCS switch are propagated to all switches in the fabric. Brocade 5300 Hardware Installation Guide 53-1000858-07...
  • Page 64 Brocade 5300 Hardware Installation Guide 53-1000858-07...

  • Page 65: Monitoring The Device

    The switch runs POST by default each time it is powered on; it can take up to several minutes to boot and complete POST. To power the Brocade 5300 off, power off both power supplies by setting each AC power switch to "O". All devices are returned to their initial state the next time the switch is powered on.
  • Page 66 LED activity interpretation FIGURE 36 LEDs on Port Side of Brocade 5300 Brocade 5300 System status LED System power LED Console port Ethernet port Ethernet speed LED Ethernet link LED FC port status LED (port 0) FC port status LED (port 4) 10.

  • Page 67: Led Patterns

    LED activity interpretation FIGURE 37 LEDs on non-port side of Brocade 5300 Power supply #2 status LED Power supply #2 Fan assembly #3 Fan assembly #2 Fan assembly #1 Power supply #1 status LED Power supply #1 Fan assembly #3 status LED Fan assembly #2 status LED 10.
  • Page 68 Power supply is not receiving power Verify the power supply is on and or is off. seated and the power cord is connected to a functioning power source. Steady green Power supply is operating normally. No action required. Brocade 5300 Hardware Installation Guide 53-1000858-07...

  • Page 69: Post And Boot Specifications

    The success or failure results of the diagnostic tests that run during POST can be monitored through LED activity, the error log, or the command line interface. POST includes the following tasks: Conducts preliminary POST diagnostics. Initializes the operating system. Initializes hardware. Runs diagnostic tests on several functions, including circuitry, port functionality, memory, statistics counters, and serialization. Brocade 5300 Hardware Installation Guide 53-1000858-07...

  • Page 70: Boot

    Fabric OS Message Reference Manual . Brocade 5300 Maintenance The Brocade 5300 is designed for high availability and low failure; it does not require any regular physical maintenance. It includes diagnostic tests and field-replaceable units, described in the following sections.

  • Page 71: Field Replaceable Units (Frus)

    The two power supplies are hot-swappable. They are identical and fit into either power supply slot. Fabric OS identifies the power supplies as follows (viewing the switch from the non-port side): • Power supply 1 on the right • Power supply 2 on the left Brocade 5300 Hardware Installation Guide 53-1000858-07...

  • Page 72: Fan Assemblies

    Fan 2 is Ok, speed is 4821 RPM Fan 3 is Ok, speed is 4891 RPM br5300:admin> For further information on replacing the fan assemblies, see the Brocade 5300 Fan Assembly Replacement Procedure . Brocade 5300 Hardware Installation Guide 53-1000858-07...

  • Page 73: Removal And Replacement Procedures

    Power supply 1 and Power supply 2. The actual appearance of the switch may differ from this illustration but the locations are correct. FIGURE 39 Power supplies on the non-port side Switch Non-port side Power supply 1 Power supply 2 Brocade 5300 Hardware Installation Guide 53-1000858-07...

  • Page 74: Time Required

    To leave the Switch or SAN Router in service while replacing a power supply, verify that the other power supply (the one not being replaced) has been powered on for at least four seconds and has a steady green LED. Brocade 5300 Hardware Installation Guide 53-1000858-07...
  • Page 75 Verify that the LED on the new power supply displays a steady green light while the Switch or SAN Router is operating (see the previous table). If the LED is not a steady green, ensure that the power supply is securely installed and seated properly. Brocade 5300 Hardware Installation Guide 53-1000858-07...
  • Page 76 Power supply status can also be viewed using the Web Tools application. See the following figure for the location of Power supply 1 and Power supply 2. FIGURE 40 Inserting the power supply Switch or SAN Router Power supply Captive screw Handle Status LED AC Power receptacle AC power switch Brocade 5300 Hardware Installation Guide 53-1000858-07...

  • Page 77: Removing And Replacing A Fan Assembly

    Removing and replacing a fan assembly The Brocade 5300 switch has three fan assemblies as displayed in the following figure. Fabric OS identifies the fans from left to right as Fan assembly #3, Fan assembly #2, and Fan assembly #1.

  • Page 78: Time Required

    The fan FRU was disabled by the user Time required Replacing a fan assembly in the Brocade 5300 switch should take less than two minutes. Items required You need the following items to replace a fan assembly in a Brocade 5300: •...
  • Page 79 Optionally, display the fan status using the fanShow command from the CLI (see the previous figure for the locations of Fan assembly #1, Fan assembly #2, and Fan assembly #3). FIGURE 42 Inserting the fan assembly Brocade 5300 Fan assembly unit Captive screw Status LED Handle Non-port side Brocade 5300 Hardware Installation Guide 53-1000858-07...
  • Page 80 Brocade 5300 Hardware Installation Guide 53-1000858-07...

  • Page 81: Brocade 5300 Technical Specifications

    They default to high speed upon boot, then switch to low speed as Fabric OS comes online, returning to high speed only as required. Weight and physical dimensions The following table lists the weight and dimensions of the Brocade 5300. TABLE 6 Physical specifications Dimension...

  • Page 82: Facility Requirements

    Facility requirements Facility requirements The following table provides the facilities requirements that must be met for the Brocade 5300. TABLE 7 Facility Requirements Type Requirements Electrical • Primary AC input 100-240 VAC, 2.0A, 47-63 Hz; switch autosenses input voltage •...

  • Page 83: General Specifications

    1280 Gbps if all 80 ports are running at 8 Gbps, full duplex Port-to-port latency Less than 2100 nanoseconds with no contention (destination port is free) The following table lists the electromagnetic compatibility (EMC) for the Brocade 5300. TABLE 11 EMC specifications Country...

  • Page 84: Data Transmission Ranges

    1 GB Fibre Channel port specifications The Fibre Channel ports in the Brocade 5300 are compatible with SWL, LWL, and ELWL SFP transceivers. The strength of the signal is determined by the type of transceiver in use. The ports meet all required safety standards. For more information about these standards, see Regulatory Statements.

  • Page 85: Serial Port Specifications

    Regulatory certifications Serial port specifications The serial port is located on the port side of the switch. The Brocade 5300 uses an RJ-45 connector for the serial port. An RJ-45 to DB9 adaptor cable is also provided with the switch.

  • Page 86: Regulatory Compliance (Environmental)

    Section 1502 of the Dodd-Frank Wall Street Reform and Consumer Protection Act of 2010 - U.S. Conflict Minerals. • 30/2011/TT-BCT - Vietnam circular. • SJ/T 11363-2006 Requirements for Concentration Limits for Certain Hazardous Substances in EIPs (China). • SJ/T 11364-2006 Marking for the Control of Pollution Caused by EIPs (China). Brocade 5300 Hardware Installation Guide 53-1000858-07...

  • Page 87: Regulatory Statements

    European Council directives, laws, and standards: • Electromagnetic Compatibility (EMC) Directive 2014/30/EU • Low Voltage Directive (LVD) 2014/35/EU • EN 55032/EN 55024 (European Immunity Requirements) – EN61000-3-2/JEIDA (European and Japanese Harmonics Spec) – EN61000-3-3 Brocade 5300 Hardware Installation Guide 53-1000858-07...

  • Page 88: China Ccc Statement

    This equipment has been tested and complies with the limits for a Class A computing device pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. Brocade 5300 Hardware Installation Guide 53-1000858-07...

  • Page 89: Kcc Statement (Republic Of Korea)

    This is a Class A product based on the standard of the Voluntary Control Council for Interference by Information Technology Equipment (VCCI). If this equipment is used in a domestic environment, radio disturbance might arise. When such trouble occurs, the user might be required to take corrective actions. Brocade 5300 Hardware Installation Guide 53-1000858-07...
  • Page 90 Brocade 5300 Hardware Installation Guide 53-1000858-07...

  • Page 91: Cautions And Danger Notices

    Stellen Sie sicher, dass an der Vorderseite, den Seiten und an der Rückseite der Luftstrom nicht behindert wird. MISE EN GARDE Vérifiez que rien ne restreint la circulation d'air devant, derrière et sur les côtés du dispositif et qu'elle peut se faire librement. Brocade 5300 Hardware Installation Guide 53-1000858-07...

  • Page 92: Electrical Cautions

    Si no instala un módulo o un fuente de alimentación en la ranura, deberá mantener el panel de ranuras en su lugar. Si pone en funcionamiento el chasis con una ranura descubierta, el sistema sufrirá sobrecalentamiento. Brocade 5300 Hardware Installation Guide 53-1000858-07...

  • Page 93: Danger Notices

    Pour des raisons de sécurité, la dragonne ESD doit contenir une résistance de série 1 méga ohm. PELIGRO Por razones de seguridad, la correa de muñeca ESD deberá contener un resistor en serie de 1 mega ohmio. Brocade 5300 Hardware Installation Guide 53-1000858-07...
  • Page 94 Las baterías usadas para respaldo de RTC/NVRAM no se encuentran en areas de acceso del operador. Existe riesgo de explosión si una batería es remplazada por un tipo incorrecto. Deshágase de los componentes usados con las baterías según las politicas y regulaciones locales. Brocade 5300 Hardware Installation Guide 53-1000858-07...

  • Page 95: Dangers Related To Equipment Weight

    Vérifiez que le bâti abritant le dispositif est bien fixé afin qu'il ne devienne pas instable ou qu'il ne risque pas de tomber. PELIGRO Verifique que el bastidor que alberga el instrumento está asegurado correctamente para evitar que pueda hacerse inestable o que caiga. Brocade 5300 Hardware Installation Guide 53-1000858-07...

This manual is also suitable for:

5100

Table of Contents