Fast Open GPS Tracking – F12 ......................11 More Settings ........................... 11 Configure by Computer ........................... 12 Run “Meitrack Manager.exe”, it will detect Comm port and read all MT90’s parameters automatically: ..13 SMS Tracking ............................ 14 GPRS Tracking........................... 16 Log on GPS Platform ............................
Meiligao (MEITRACK), or transmitted in any form, either electronically or mechanically, including photocopying and recording. In no event shall Meiligao (MEITRACK) be liable for direct, indirect, special, incidental, or consequential damages (including but not limited to economic loss, personal injury, and loss of asset and property) arising out of the use or inability or illegality to use the product or documentation.
Button Long press for 2 seconds to turn off MT90. Press to wake MT90 up from sleep mode, power LED will slowly flash for 10 seconds. Mini USB Mini USB is used for charging, connecting to computer for setting up parameters, updating software and so on.
Page 6
Revision V1.4 Confidential External Documentation logger will run automatically. (MT90 will log the route every 30 seconds automatically. Route record can be exported with the computer. Long press for 2 seconds again, when the buffer “BI” twice, and the logger will stop automatically.
External Documentation 6. First Use Remove the Battery Cover With the device turned off, place your MT90 with the front facing down. Use the mini screwdriver to remove the two screws to release the back cover. Lift up the back cover from the notch at the bottom of the device.
Quick Operation Instruction Operation tips: to properly use the MT90, common parameters should be set in advance before initial use. This can be done by using the parameter editor or by sending SMS commands to the device. Doing so will adapt the tracker to local time, allowing you to better enjoy the GPS service of Meitrack.
7.1 Real-time Location Tracking This location-tracking for knowing the current location of MT90, to ensure normal function of the GPS signal. Call the SIM card number embedded in MT90, hang up till the dial sound 2-3 times, as follows: ...
IMEI,A72,OK Successfully set monitor number. When the preset monitor number calls the MT90, the device will answer automatically and enter into the listening state. The device will not emit any sound. Note: the default value is empty, if the function numbers are less than three while setting, it must be added “,”...
IMEI,B35,OK Set the time zone successfully. Note: this value is your MT90’s IMEI number. The device will send this data automatically and these numbers don’t represent anything significant to the functionality of the tracker. Below the same applies. 7.6 Fast Open GPS Tracking – F12 This command is used to quickly open an embedded SIM card’s GPRS function, to ensure normal function of...
Configure by Computer This part mainly shows you how to use the Meitrack Manager. Please refer to the Meitrack Manager User Guide for more information regarding configuration and functions. Install the MT90 software of Meitrack Manager Find the software of Meitrack Manager from the CD.
File Name MEITRACK MT90 User Guide Creator Cavana Cheung Project MT90 Creation Date 2011-05-16 Update Date 2012-04-06 Sub Project User Guide Page 14 of 18 Revision V1.4 Confidential External Documentation 8.1 SMS Tracking Items Descriptions SMS Password The defaulted value 0000 of SMS password for sending SMS commands...
Page 15
Revision V1.4 Confidential External Documentation Low Battery Alarm Report when MT90 speeds higher than the preset value. SMS header defaulted as “Speeding”. GPS Blind Area Alarm Enter alarm: report when MT90 enters GPS blind area. SMS header defaulted as “No Fix”.
Online configuration For more information about our GPS platform, please refer to Meitrack Meigps Platform User Guide. 10. Safety and Usage Information Handle and dispose of batteries and chargers with care Use only Meitrack-approved accessories specially designed for your device. Incompatible accessories can cause serious injuries or damages to your device.
Need help?
Do you have a question about the MT90 and is the answer not in the manual?
Questions and answers