Advertisement
....
'
....
(0
Assigning the Remote Control Functions - REMOTE Menu
341
PARA REMOTE CONFIG: Select the REMOTE 2 connector pins for which you want to
change the function.
The
factory settings for each pin are given below.<=? 342
I PIN ... : CHOI
2PIN ••• :CH02
3 PIN ... : EXT SYNC
4PIN ••• :MONO
5
PIN ... : SAFE AREA
6
PIN ... : unused
7 PIN ... : unused
8PIN ••• :TALLY
342
1-8 PIN (1/2): Assign a function to the selected pin .
CH: Select a channel number. Enter the desired channel number with the numeric keypad.
····: Set to unused.
UNDERSCAN: Set underscan on or off.
16:9: Set a 16:9 aspect ratio on or off.
H DELAY: Set the horizontal sync display on or off.
V DELAY: Set rhe vertical sync display on or off.
EXT SYNC: Set the synchronization to external sync signals enabled or disabled.
COMB: Set the comb filter on or off.
APERTURE: Set the correction of frequency characteristics enabled or disabled.
MONO: Set monochrome display on or off.
342
1-8 PIN (1J2): Assign a function to the selected pin.
BLUE ONLY: Set the blue signal pictures display (monochrome) on or off.
R OFF: Set cutting red beams enabled or disabled.
G OFF: Set cutting green beams enabled or disabled.
B OFF: Set culling blue beams enabled or disabled.
VITC ON: Set the .VITC display on or off.
SAFE AREA ON: Set the safe area display on or off.
CAPTION VISION: Set the caption vision on or off.
TALLY ON: Set tally signals on or off.
DEGAUSS ON: Set degaussing on or off.
POWER ON: Set the monitor power on or off.
For information about pin connections, su the description of the REMOTE 2 connector in "locmion
and Function of Parts·· on page JO.
343
SERI REMOTE CONFIG: Set the monitor address and group number of the
monitor currently connected directly to the control unit. The monitors to be assigned
addresses and group numbers must be directly connected to the control unit and set one at
a time.
MONITOR ADDRESS: Enter a number.
GROUP ADDRESS: Enter a number.
Setting the Password
-
PASSWORD Menu
A four-digit password can be specified and applied to
desired menu options to prohibit the menu settings
from being changed without permission. The
password is set with the PASSWORD menu.
A password is always assigned to the PASSWORD
menu (factory setting: 9999). When a new password is
created, it is automatically applied to the PASSWORD
menu.
Use of the Password
The message "'PLEASE ENTER PASSWORD" is
displayed when an attempt is made to select a menu
item for which the password has been applied. The
correct password must be entered with the numeric
keypad within about five seconds.
If the password is not entered correctly
If an incorrect password is entered,-or if nothing is
entered within about five seconds from when the
message is displayed, the message ··INCORRECT
ENTRY" is displayed, and the menus disappear from
the screen.
•.·.-.,,~.,.ij..,ij~~~t~.~~:f!!etit;<-i
This section explains the setting lists displayed in the
menu.
The lists are numbered and shown with indentations to
indicate the hierarchy in the menu.
If
a setting in each list leads to another list or a
monitor operation, the list number or the opera1ion is
indicated after the<=? mark. (Settings without the<=?
mark end in a single list.)
Select SET UP from the menu list.
CONTROL PRESET ADJ ...
CQI,_()_R IEMP ADJ...,,.
MEMORY CARD ...
COPY ...
STATUS ...
MAINTENANCE ...
KEY PROTECT
OFF
Menu list
300
SET UP menu list: Choose the menu for setting the desired items.
INPUT CONFIGURATION
menu
REMO_TE menu
SYSTEM CONFIGURATION
menu
ON SCREEN SET menu
ALIGNMENT menu
Advertisement
