Advertisement
....
I
....
w
Preset
Adjustment
of the Picture
Level Control
Knobs
-
CONTROL
PRESET ADJ Menu
110
MANUAL (PRESET/xxCH):
Adjust values by turning the PHASE, BRIGHT,
CHROMA, and/or CONTRAST knobs.
PHASE:
xxxx
CHROMA: xxxx
BRIGHT: xxxx
CONTRAST: xxxx
120
AUTO (PRESET/xxCH):
Select the color bar signal to be used for automatic adjustment
=:>
Adjustment Is
carried out.
FULL FIELD CB 100:
100% full-field color bar
FULL FIELD CB
75: 75% full-field color bar
SMPTE CB: SMPTE
standard color bar
EIA CB:
EIA standard color bar
130
COPY (PRESET/xxCH):
Select the source to be copied from.
OTHER VALUE ... :
Copy data from another channel or from PRESET setting.
=:>
131
OTHER MONITOR ... :
Copy data from another monitor.=!> 133
MEMORY CARD ... :
Copy data from a memory card. =!> 136
131
OTHER VALUE (PRESET/xxCH):
Choose either PRESET or CH SET.
=:>
Copy Is carried out •
PRESET:
Copy common data.
CH SET:
Copy data set for another channel. Input the number of the channel from which
the data will be copied.
133
OTHER MONITOR (PRESET/xxCH):
Input the address of the monitor from
which the data will be copied.
=:>
134
j
MONITOR ADDRESS: Input the address.
134
OTHER MONITOR (PRESET/xxCH):
Choose either PRESET or CH SET.
=:>
Copy Is carried out,
PRESET:
Copy common data.
CH SET:
Copy data set for another channel. Input the number of the channel from
which the data will
be
copied.
136
MEMORY CARD (PRESET/xxCH):
Select the file name. =!> 137
[ FILE NAME: Select the file name.
137
FILE NAME (PRESET/xxCH):
Choose either PRESET or CH SET.
=:>
Copy Is carried
out.
PRESET:
Copy common data.
CH SET:
Copy data set for another channel. Input the number of the channel from
which
the
data will be copied.
Adjusting the Color Temperature -
COLOR TEMP
ADJ Menu
The color temperature is adjusted with the COLOR
TEMP ADJ menu. The color temperature can be set
either commonly to all channels or individually for
each channel.
The adjusted value can then be used as an original
value.
Color temperature adjustment can
be
made in the
following four ways:
(I)
Knob adjustment
Adjust the color temperature with the bias and gain
knobs.
(2) Automatic adjustment using a probe
Bias
and
gain can be adjusted automatically by
connecting a color analyzer such as the Minolta CA-
100.
(3)
Copying other data
Copying data from other channels, common data, other
BVM-series monitors that have been connected via the
serial remote connector, or from data stored in monitor
memory cards
(4) Restoring factory settings
>i~rfftl,,
••
1111~~ilit;~i
1
il/::
,&j}1.::t;
This section explains the setting lists displayed in the
menu.
The lists are numbered and shown with indentations to
indicate the hierarchy in the menu.
If a setting in each list leads to another list or a
monitor operation, the list number or the operation is
indicated after the
=:>
mark. (Settings without the
=:>
mark end in a single !isl.)
Select COLOR TEMP ADJ from the main menu list.
CONTROL PRESET ADJ ...
St:TUP ...
MEMORY CARD ...
COPY ...
STATUS ...
MAINTENANCE ...
KEY PROTECT
OFF
Menu list
l
200
COLOR TEMP ADJ menu: Select STD, COL I, COL2, or CH SET. =!> 201
STD:
Use common data (factory setting: D65).
COLI:
Use common data (factory setting: D65 ).
COL2:
Use common data (factory setting: D93).
CH SET:
Use data for each individual channel (factory setting: D65). Use the numeric keypad to select the
desired channel.
--~~...._,__,,
___
,...,~~~
..... L#"
....
,&>,..,._.....-,-..~~,,.,.,.__,,,,-aso,',,Ca,~~-·."~'""'~"~'~-
"'>
,
b,---••·~"-"'"'"•~•
~<.,.<-"'--•s',
__
_
Advertisement
