Table of Contents
Advertisement
Quick Links
OWNER'S MANUAL
Outdoor Inversion Table
Item#6571
The specifications of this product may vary from this photo and are subject to change without notice.
IRONMAN, IRONMAN TRIATHLON and M-DOT are registered trademarks of World Triathlon Corporation.
This product is licensed by the World Triathlon Corporation.
Advertisement
Table of Contents
Related Manuals for Ironman Fitness 6571
Summary of Contents for Ironman Fitness 6571
- Page 1 Outdoor Inversion Table Item#6571 The specifications of this product may vary from this photo and are subject to change without notice. IRONMAN, IRONMAN TRIATHLON and M-DOT are registered trademarks of World Triathlon Corporation.
- Page 2 6571.1‐101315 ...
-
Page 3: Table Of Contents
TABLE OF CONTENTS SERVICE-------------------------------------------------------------------- 2 IMPORTANT SAFETY INSTRUCTIONS--------------------------- 3 LABEL PLACEMENT---------------------------------------------------- 5 OVERVIEW DRAWING------------------------------------------------- 6 PART LIST----------------------------------------------------------------- 7 HARDWARE LIST & TOOLS----------------------------------------- 8 ASSEMBLY----------------------------------------------------------------9 ADJUSTMENT------------------------------------------------------------15 HOW TO USE------------------------------------------------------------16 OPERATION--------------------------------------------------------------17 WARM UP----------------------------------------------------------------- 18 WARRANTY-------------------------------------------------------------- 19 FAX FORM---------------------------------------------------------------- 20 1 ... -
Page 4: Service
SERVICE IMPORTANT: FOR NORTH AMERICA ONLY For damaged or defective product, questions, replacement parts or any other service support, please contact our customer service department (8:00 AM - 5:00 PM Pacific Standard Time, Daily) by the below methods: For Best Service, please Email: Service@paradigmhw.com Response Time: 1-2 Business Days... -
Page 5: Important Safety Instructions
IMPORTANT SAFETY INSTRUCTIONS This inversion table was designed and built for optimal safety. However, certain precautions apply whenever you operate the exercise equipment. Be sure to read the entire manual before assembling and operating the equipment. When using this equipment, basic precautions should always be followed, including the following: ... - Page 6 IMPORTANT SAFETY INSTRUCTIONS WARNING - Risk of personal injury - Keep body parts, hair, loose clothing and jewelry clear of all moving parts. NOTE: Maximum user weight for this product is 350 lbs (159 kgs.) Maximum Rated Height for this product is 6’6”/198cm. ...
-
Page 7: Label Placement
LABEL PLACEMENT 5 ... -
Page 8: Overview Drawing
OVERVIEW DRAWING 6 ... -
Page 9: Part List
PART LIST Description Q'ty Description Q'ty Pivot Arm Rotation Cap I Front Frame Ø60xØ19.5x21 Rear Frame 26 Round Cap Bed Frame 27 Hex Bolt M6x47 Left Pivot Arm 28 Hex Bolt M8x23 Handlebar 29 Hex Bolt M8x60 Adjustable lnstep Frame 30 Hex Bolt M8x55 Pivot Arm 31 Hex Bolt M8x25 Adjustable Boom... -
Page 10: Hardware List & Tools
HARDWARE LIST & TOOLS 8 ... -
Page 11: Assembly
ASSEMBLY The product weighs more than 44lbs / 20kgs and should be assembled and moved by two or more people. Hex Wrench 1PC Allen Wrench 5mm 1PC Step 1. Stand up the base of the machine by separating the Front and Rear Frames(1, 2). Pull the Front and Rear Frames (1, 2) as far apart from each other as possible. - Page 12 ASSEMBLY Hex Wrench 1PC Allen Wrench 5mm 1PC Step 2. 1. Attach the Bed Frame (3) onto the Pivot Arm (7) and tighten with two Hex Bolts (28), two Lock Nut (36) and two Washer (13) by using the Hex Wrench, Allen Wrench 5mm provided. 2.
- Page 13 ASSEMBLY Hex Wrench 1PC Allen Wrench 5mm 1PC Step 3. 1. Attach the bracket of Handlebar (5) onto the Rear Frame (2) and tighten with one Hex Bolt (30), one Nylon Nut (36), and two Washers (39) by using the Hex Wrench provided. 2.
- Page 14 ASSEMBLY Hex Wrench 2 PC Step 4. 1. Slide the Heel Holder Brackets (10) and Rubber Heel Holders (12) onto both ends of the Front Leg Holder (6) until the teeth of Holder Bracket (10) are wedged into the slots on Front Leg Holder (6), as shown in Figure A and B.
- Page 15 ASSEMBLY Step 5. 1. Loosen the Knob (15). 2. Pull on the ball of the Boom Spring Knob (19) in order to slide the Adjustable Boom (8) in to the square tube of Bed Frame (3). 3. Adjust to your desired height. 4.
- Page 16 ASSEMBLY Step 6. 1. Attach a Safety Hook (45) to the loops at both ends of the Nylon Strap (47). 2. Attach one end of Nylon Strap with Safety Hook (45) to the underside of Bed Frame (3) as shown in image A. 3.
-
Page 17: Adjustment
ADJUSTMENT LENGTHEN SHORTEN THE STRAP For added safety, a nylon strap has been included to help restrict the degree of inversion. This strap can be adjusted to different lengths to allow for a greater or lesser degrees of inversion. To lengthen the Nylon Strap (47) feed the top end of Nylon Strap (47) into the strap lock, and pull on the lower end of the strap. -
Page 18: How To Use
HOW TO USE Set the Adjustable Boom to your height 1. Turn Knob counter-clockwise to loosen the Adjustable Boom. 2. Pull Boom Spring Knob as you adjust Adjustable the Adjustable Boom to desired height. Boom 3. Turn Knob clockwise to tighten the Boom Spring Knob Adjustable Boom. -
Page 19: Operation
ERATION N USIN NG THE E INVER RSION T TABLE 1. Start by y lying fully y back on t the bed wi th your ha ands at you ur side, or resting on n your thig 2. Slowly r raise your arms, allo owing the t... -
Page 20: Warm Up
WARM U adriceps S Stretch With h one hand d against a a wall for b balance, re ach back a pull your right foot up. B Bring your h heel as clo ose to your butt tocks as po ossible. -
Page 21: Warranty
WARRANTY MANUFACTURER’S LIMITED WARRANTY Paradigm Health & Wellness warrants to the original purchaser that this product is free from defects in material and workmanship when used for the purpose intended, under the conditions that it has been installed and operated in accordance with Paradigm’s Owner’s Manual. -
Page 22: Fax Form
FAX FORM Paradigm Health & Wellness, Inc. PARTS REQUEST FAX FORM Please fax this form to (1-626-810-2166) OR YOU CAN EMAIL CUSTOMER SERVICE REQUESTS TO service@paradigmhw.com NAME: _______________________________________________________ ADDRESS: ____________________________________________________ CITY ______________ STATE ______________ ZIP ___________________ TELEPHONE: (Day) _____________________________________________ (Night) ____________________________________________ (Email Address) ____________________________________ SERIAL#: __________________________________________ MODEL#: __________________________________________...